Power and Performance Management Strategies on NoC-Based Multicore Platforms, Using DVFS, Adaptive Algorithm and Task Parallelism

This work presents synopsis of efficient strategies used in power managements for achieving the most economical power and energy consumption in multicore systems, FPGA and NoC Platforms. In this work, a practical approach was taken, in an effort to validate the significance of the proposed Adaptive Power Management Algorithm (APMA), proposed for system developed, for this thesis project. This system comprise arithmetic and logic unit, up and down counters, adder, state machine and multiplexer. The essence of carrying this project firstly, is to develop a system that will be used for this power management project. Secondly, to perform area and power synopsis of the system on these various scalable technology platforms, UMC 90nm nanotechnology 1.2v, UMC 90nm nanotechnology 1.32v and UMC 0.18 μmNanotechnology 1.80v, in order to examine the difference in area and power consumption of the system on the platforms. Thirdly, to explore various strategies that can be used to reducing system’s power consumption and to propose an adaptive power management algorithm that can be used to reduce the power consumption of the system. The strategies introduced in this work comprise Dynamic Voltage Frequency Scaling (DVFS) and task parallelism. After the system development, it was run on FPGA board, basically NoC Platforms and on these various technology platforms UMC 90nm nanotechnology1.2v, UMC 90nm nanotechnology 1.32v and UMC180 nm nanotechnology 1.80v, the system synthesis was successfully accomplished, the simulated result analysis shows that the system meets all functional requirements, the power consumption and the area utilization were recorded and analyzed in chapter 7 of this work. This work extensively reviewed various strategies for managing power consumption which were quantitative research works by many researchers and companies, it's a mixture of study analysis and experimented lab works, it condensed and presents the whole basic concepts of power management strategy from quality technical papers.

Timing of Capacity Change: Models for Capital Intensive Industry

The suitable timing of capacity investments is a remarkable issue especially in capital intensive industries. Despite its importance, fairly few studies have been published on the topic. In the present study models for the timing of capacity change in capital intensive industry are developed. The study considers mainly the optimal timing of single capacity changes. The review of earlier research describes connections between cost, capacity and timing literature, and empirical examples are used to describe the starting point of the study and to test the developed models. The study includes four models, which describe the timing question from different perspectives. The first model, which minimizes unit costs, has been built for capacity expansion and replacement situations. It is shown that the optimal timing of an investment can be presented with the capacity and cost advantage ratios. After the unit cost minimization model the view is extended to the direction of profit maximization. The second model states that early investments are preferable if the change of fixed costs is small compared to the change of the contribution margin. The third model is a numerical discounted cash flow model, which emphasizes the roles of start-up time, capacity utilization rate and value of waiting as drivers of the profitable timing of a project. The last model expands the view from project level to company level and connects the flexibility of assets and cost structures to the timing problem. The main results of the research are the solutions of the models and analysis or simulations done with the models. The relevance and applicability of the results are verified by evaluating the logic of the models and by numerical cases.

Automated formulation of optimisation models for steel beam structures

Over 70% of the total costs of an end product are consequences of decisions that are made during the design process. A search for optimal cross-sections will often have only a marginal effect on the amount of material used if the geometry of a structure is fixed and if the cross-sectional characteristics of its elements are property designed by conventional methods. In recent years, optimalgeometry has become a central area of research in the automated design of structures. It is generally accepted that no single optimisation algorithm is suitable for all engineering design problems. An appropriate algorithm, therefore, mustbe selected individually for each optimisation situation. Modelling is the mosttime consuming phase in the optimisation of steel and metal structures. In thisresearch, the goal was to develop a method and computer program, which reduces the modelling and optimisation time for structural design. The program needed anoptimisation algorithm that is suitable for various engineering design problems. Because Finite Element modelling is commonly used in the design of steel and metal structures, the interaction between a finite element tool and optimisation tool needed a practical solution. The developed method and computer programs were tested with standard optimisation tests and practical design optimisation cases. Three generations of computer programs are developed. The programs combine anoptimisation problem modelling tool and FE-modelling program using three alternate methdos. The modelling and optimisation was demonstrated in the design of a new boom construction and steel structures of flat and ridge roofs. This thesis demonstrates that the most time consuming modelling time is significantly reduced. Modelling errors are reduced and the results are more reliable. A new selection rule for the evolution algorithm, which eliminates the need for constraint weight factors is tested with optimisation cases of the steel structures that include hundreds of constraints. It is seen that the tested algorithm can be used nearly as a black box without parameter settings and penalty factors of the constraints.

Dynamic Capabilities and Firm Performance

Firms operating in a changing environment have a need for structures and practices that provide flexibility and enable rapid response to changes. Given the challenges they face in attempts to keep up with market needs, they have to continuously improve their processes and products, and develop new products to match market requirements. Success in changing markets depends on the firm's ability to convert knowledge into innovations, and consequently their internal structures and capabilities have an important role in innovation activities. According 10 the dynamic capability view of the firm, firms thus need dynamic capabilities in (he form ofassets, processes and structures that enable strategic flexibility and support entrepreneurial opportunity sensing and exploitation. Dynamic capabilities are also needed in conditions of rapid change in the operating environment, and in activities such as new product development and expansion to new markets. Despite the growing interest in these issues and the theoretical developments in the field of strategy research, there are still only very few empirical studies, and large-scale empirical studies in particular, that provide evidence that firms'dynamic capabilities are reflected in performance differences. This thesis represents an attempt to advance the research by providing empirical evidence of thelinkages between the firm's dynamic capabilities and performance in intenationalization and innovation activities. The aim is thus to increase knowledge and enhance understanding of the organizational factors that explain interfirm performance differences. The study is in two parts. The first part is the introduction and the second part comprises five research publications covering the theoretical foundations of the dynamic capability view and subsequent empirical analyses. Quantitative research methodology is used throughout. The thesis contributes to the literature in several ways. While a lot of prior research on dynamic capabilities is conceptual in nature, or conducted through case studies, this thesis introduces empirical measures for assessing the different aspects, and uses large-scale sampling to investigate the relationships between them and performance indicators. The dynamic capability view is further developed by integrating theoretical frameworks and research traditions from several disciplines. The results of the study provide support for the basic tenets of the dynamic capability view. The empirical findings demonstrate that the firm's ability to renew its knowledge base and other intangible assets, its proactive, entrepreneurial behavior, and the structures and practices that support operational flexibility arepositively related to performance indicators.

Representations of work and worker in the three generations of knowledge management. Critical Discourse Analysis of selected texts.

The thesis studies the representations of different elements of contemporary work as present in Knowledge Management (KM). KM is approached as management discourse that is seen to affect and influence managerial practices in organizations. As representatives of KM discourse four journal articles are analyzed, using the methodology of Critical Discourse Analysis and the framework of Critical Management Studies, with a special emphasis on the question of structure and agency. The results of the analysis reveal that structural elements such as information technology and organizational structures are strongly present in the most influential KM representations, making their improvement also a desirable course of action for managers. In contrast agentic properties are not in a central role, they are subjugated to structural constraints of varying kind and degree. The thesis claims that one such constraint is KM discourse itself, influencing managerial and organizational choices and decision making. The thesis concludes that the way human beings are represented, studied and treated in management studies such as KM needs to be re-examined. Pro gradu-tutkielmassa analysoidaan työhön ja sen tekijään liittyviä representaatioita Tietojohtamisen kirjallisuudessa. Tietojohtamista tarkastellaan liikkeenjohdollisena diskurssina, jolla nähdään olevan vaikutus organisaatioiden päätöksentekoon ja toimintaan. Tutkielmassa analysoidaan neljä Tietojohtamisen tieteellistä artikkelia, käyttäen metodina kriittistä diskurssianalyysiä. Tutkielman viitekehyksenä on kriittinen liikkeenjohdon tutkimus. Lisäksi työssä pohditaan kysymystä rakenteen ja toimijan välisestä vuorovaikutuksesta. Tutkielman analyysi paljastaa, että tietojohtamisen vaikutusvaltaisimmat representaatiot painottavat rakenteellisia tekijöitä, kuten informaatioteknologiaa ja organisaatiorakenteita. Tämän seurauksena mm. panostukset em. tekijöihin nähdään organisaatioissa toivottavana toimintana. Vastaavasti representaatiot jotka painottavat yksilöitä ja toimintaa ovat em. tekijöille alisteisessa asemassa. Tapaa, jolla yksilöitä kuvataan ja käsitellään Tietojohtamisen diskurssissa, tulisikin laajentaa ja monipuolistaa.

The use of future-oriented knowledge in regional innovation processes: Research on knowledge generation, transfer and conversion

The importance of the regional level in research has risen in the last few decades and a vast literature in the fields of, for instance, evolutionary and institutional economics, network theories, innovations and learning systems, as well as sociology, has focused on regional level questions. Recently the policy makers and regional actors have also began to pay increasing attention to the knowledge economy and its needs, in general, and the connectivity and support structures of regional clusters in particular. Nowadays knowledge is generally considered as the most important source of competitive advantage, but even the most specialised forms of knowledge are becoming a short-lived resource for example due to the accelerating pace of technological change. This emphasizes the need of foresight activities in national, regional and organizational levels and the integration of foresight and innovation activities. In regional setting this development sets great challenges especially in those regions having no university and thus usually very limited resources for research activities. Also the research problem of this dissertation is related to the need to better incorporate the information produced by foresight process to facilitate and to be used in regional practice-based innovation processes. This dissertation is a constructive case study the case being Lahti region and a network facilitating innovation policy adopted in that region. Dissertation consists of a summary and five articles and during the research process a construct or a conceptual model for solving this real life problem has been developed. It is also being implemented as part of the network facilitating innovation policy in the Lahti region.

Managerial Careers in the IT Industry: Women in China and in Finland

This research focuses on the career experiences of women managers in the IT industry in China and Finland, two countries with different cultures, policies, size of population, and social and economic structures regarding work-life support and equal opportunities. The object of this research is to present a cross-cultural comparison of women’s career experiences and how women themselves understand and account for their careers. The study explores how the macro and the micro levels of cultural and social processes become manifested in the lives of individual women. The main argument in this thesis is that culture plays a crucial role in making sense of women’s career experiences, although its role should be understood through its interrelationship with other social processes, e.g., institutional relations, social policies, industrial structures and organizations, as well as globalization. The interrelationship of a series of cultural and social processes affects individuals’ attitudes to, and arrangement and organization of, their work and family lives. This thesis consists of two parts. The first part introduces the research topic and discusses the overall results. The second part comprises five research papers. The main research question of the study is: How do cultural and social processes affect the experiences of women managers? Quantitative and qualitative research methods, which include in-depth interviews, Q-methodology, interpretive analysis, and questionnaires, are used in the study. The main theoretical background is culturally sensitive career theory and the theory of individual differences. The results of this study are viewed through a feminist lens. The research methodology applied allows new explorations on how demographic factors, work experiences, lifestyle issues, and organizational cultures can jointly affect women’s managerial careers. The sample group used in the research is 42 women managers working in IT companies in China (21) and Finland (21). The results of the study illustrate the impact of history, tradition, culture, institutional relations, social politics, industry and organizations, and globalization on the careers of women managers. It is claimed that the role of culture – cultural norms within nations and organizations – is of great importance in the relationship of gender and work. Women’s managerial careers are affected by multiple factors (personal, social and cultural) reflecting national and inter-individual differences. The results of the study contribute to research on careers, adding particularly to the literature on gender, work and culture, and offering a complex and holistic perspective for a richer understanding of pluralism and global diversity. The results of the study indicate how old and new career perspectives are evidenced in women managers in the IT industry. The research further contributes to an understanding of women’s managerial careers from a cross-culture perspective. In addition, the study contributes to the literature on culture and extends understanding of Hofstede’s work. Further, most traditional career theories do not perceive the importance of culture in determining an individual’s career experience and this study richens understanding of women managers’ careers and has considerable implications for international human resource management. The results of this study emphasize the need, when discussing women managers’ careers, to understand the ways by which gendering is produced rather than merely examining gender differences. It is argued that the meaning of self-knowledge is critical. Further, the environment where the careers under study develop differs greatly; China and Finland are very different – culturally, historically and socially. The findings of this study should, therefore, be understood as a holistic, specific, and contextually-bound.

Novel Robot Solutions for Carrying out Field Joint Welding and Machining in the Assembly of the Vacuum Vessel of ITER

It is necessary to use highly specialized robots in ITER (International Thermonuclear Experimental Reactor) both in the manufacturing and maintenance of the reactor due to a demanding environment. The sectors of the ITER vacuum vessel (VV) require more stringent tolerances than normally expected for the size of the structure involved. VV consists of nine sectors that are to be welded together. The vacuum vessel has a toroidal chamber structure. The task of the designed robot is to carry the welding apparatus along a path with a stringent tolerance during the assembly operation. In addition to the initial vacuum vessel assembly, after a limited running period, sectors need to be replaced for repair. Mechanisms with closed-loop kinematic chains are used in the design of robots in this work. One version is a purely parallel manipulator and another is a hybrid manipulator where the parallel and serial structures are combined. Traditional industrial robots that generally have the links actuated in series are inherently not very rigid and have poor dynamic performance in high speed and high dynamic loading conditions. Compared with open chain manipulators, parallel manipulators have high stiffness, high accuracy and a high force/torque capacity in a reduced workspace. Parallel manipulators have a mechanical architecture where all of the links are connected to the base and to the end-effector of the robot. The purpose of this thesis is to develop special parallel robots for the assembly, machining and repairing of the VV of the ITER. The process of the assembly and machining of the vacuum vessel needs a special robot. By studying the structure of the vacuum vessel, two novel parallel robots were designed and built; they have six and ten degrees of freedom driven by hydraulic cylinders and electrical servo motors. Kinematic models for the proposed robots were defined and two prototypes built. Experiments for machine cutting and laser welding with the 6-DOF robot were carried out. It was demonstrated that the parallel robots are capable of holding all necessary machining tools and welding end-effectors in all positions accurately and stably inside the vacuum vessel sector. The kinematic models appeared to be complex especially in the case of the 10-DOF robot because of its redundant structure. Multibody dynamics simulations were carried out, ensuring sufficient stiffness during the robot motion. The entire design and testing processes of the robots appeared to be complex tasks due to the high specialization of the manufacturing technology needed in the ITER reactor, while the results demonstrate the applicability of the proposed solutions quite well. The results offer not only devices but also a methodology for the assembly and repair of ITER by means of parallel robots.

Teaching mathematics and programming : new approaches with empirical evaluation

Programming and mathematics are core areas of computer science (CS) and consequently also important parts of CS education. Introductory instruction in these two topics is, however, not without problems. Studies show that CS students find programming difficult to learn and that teaching mathematical topics to CS novices is challenging. One reason for the latter is the disconnection between mathematics and programming found in many CS curricula, which results in students not seeing the relevance of the subject for their studies. In addition, reports indicate that students' mathematical capability and maturity levels are dropping. The challenges faced when teaching mathematics and programming at CS departments can also be traced back to gaps in students' prior education. In Finland the high school curriculum does not include CS as a subject; instead, focus is on learning to use the computer and its applications as tools. Similarly, many of the mathematics courses emphasize application of formulas, while logic, formalisms and proofs, which are important in CS, are avoided. Consequently, high school graduates are not well prepared for studies in CS. Motivated by these challenges, the goal of the present work is to describe new approaches to teaching mathematics and programming aimed at addressing these issues: Structured derivations is a logic-based approach to teaching mathematics, where formalisms and justifications are made explicit. The aim is to help students become better at communicating their reasoning using mathematical language and logical notation at the same time as they become more confident with formalisms. The Python programming language was originally designed with education in mind, and has a simple syntax compared to many other popular languages. The aim of using it in instruction is to address algorithms and their implementation in a way that allows focus to be put on learning algorithmic thinking and programming instead of on learning a complex syntax. Invariant based programming is a diagrammatic approach to developing programs that are correct by construction. The approach is based on elementary propositional and predicate logic, and makes explicit the underlying mathematical foundations of programming. The aim is also to show how mathematics in general, and logic in particular, can be used to create better programs.

Causation and dominance : a study of Finnish causative verbs expressing social dominance

En väsentlig fråga inom såväl lingvistiska som kognitiva teorier är, hur språket beskriver kausala relationer. I finskan finns det en speciell typ av kausativa verb avledda med suffixet (U)ttA som används för att uttrycka att handlingen i fråga utförs av någon annan än subjektreferenten, t.ex. Maija haetuttaa Matilla kirjastosta kirjan ’Maija låter Matti hämta boken från biblioteket’ och Matti juoksuttaa Maijan kaupunkiin ’Matti låter Maija springa till staden’. Syftet med denna avhandling var att med exempel av sociala dominansens kausativer undersöka ordbildningens natur samt begreppet ’socialt förorsakande’. För att beskriva avledningars regelbundna argumentstruktur i form av kopplingen mellan syntaxen och semantiken upprättades deras prototypiska strukturer. Dessa verb har emellertid också specifika användningsområden som framhäver variationer i sociala relationer. Säregna egenskaper hos den sociala dominansens kausativer inkluderades i undersökningen och definierades som konstruktioner. Konstruktionerna omfattar speciella syntaktiska och/eller semantiska element och utöver det också pragmatiska värderande implikationer. Uppbyggnaden av den sociala dimensionen hos de undersökta verben består av egenskaper förbundna med typen av förorsakande, argumentens agentiva egenskaper (aktivitet eller passivitet, dominans, kontroll, viljestyrdhet och ansvarighet) samt konventionaliserade attityder och tolkningar. Ett exempel på en s.k. 'tolkningskonstruktion’ är den negativa dominansens uttryck som i avhandlingen kallas Maktmissbrukskonstruktionen. Denna konstruktion inkluderar talarens starkt kritiska hållning till den uttryckta situationen, t.ex. Asiakas juoksuttaa lentoemäntää ’Kunden låter flygvärdinnan springa’. Dessa konstruktioner fyller en viktig funktion i språklig kommunikation: att beskriva avvikande av sociala normer och att foga expressivitet till budskapet. Metodologiskt kombinerar denna avhandling teorier som baseras på det aktuella språkbruket och teoretisk lingvistisk analys. Verbens samt konstruktionernas konceptuella lexikala struktur och prototypstrukturerna analyserades med hjälp av den konceptuella semantikens verktyg, som har utvecklats av Jackendoff, Nikanne och Pörn.

Communicative and Anticipatory Decision-Making Supported by Bayesian Networks

The purpose of this research is to draw up a clear construction of an anticipatory communicative decision-making process and a successful implementation of a Bayesian application that can be used as an anticipatory communicative decision-making support system. This study is a decision-oriented and constructive research project, and it includes examples of simulated situations. As a basis for further methodological discussion about different approaches to management research, in this research, a decision-oriented approach is used, which is based on mathematics and logic, and it is intended to develop problem solving methods. The approach is theoretical and characteristic of normative management science research. Also, the approach of this study is constructive. An essential part of the constructive approach is to tie the problem to its solution with theoretical knowledge. Firstly, the basic definitions and behaviours of an anticipatory management and managerial communication are provided. These descriptions include discussions of the research environment and formed management processes. These issues define and explain the background to further research. Secondly, it is processed to managerial communication and anticipatory decision-making based on preparation, problem solution, and solution search, which are also related to risk management analysis. After that, a solution to the decision-making support application is formed, using four different Bayesian methods, as follows: the Bayesian network, the influence diagram, the qualitative probabilistic network, and the time critical dynamic network. The purpose of the discussion is not to discuss different theories but to explain the theories which are being implemented. Finally, an application of Bayesian networks to the research problem is presented. The usefulness of the prepared model in examining a problem and the represented results of research is shown. The theoretical contribution includes definitions and a model of anticipatory decision-making. The main theoretical contribution of this study has been to develop a process for anticipatory decision-making that includes management with communication, problem-solving, and the improvement of knowledge. The practical contribution includes a Bayesian Decision Support Model, which is based on Bayesian influenced diagrams. The main contributions of this research are two developed processes, one for anticipatory decision-making, and the other to produce a model of a Bayesian network for anticipatory decision-making. In summary, this research contributes to decision-making support by being one of the few publicly available academic descriptions of the anticipatory decision support system, by representing a Bayesian model that is grounded on firm theoretical discussion, by publishing algorithms suitable for decision-making support, and by defining the idea of anticipatory decision-making for a parallel version. Finally, according to the results of research, an analysis of anticipatory management for planned decision-making is presented, which is based on observation of environment, analysis of weak signals, and alternatives to creative problem solving and communication.

Integration in project business : mechanisms for integrating customers and the project network during the life-cycle of industrial projects

This thesis focuses on integration in project business, i.e. how projectbased companies organize their product and process structures when they deliver industrial solutions to their customers. The customers that invest in these solutions run their businesses in different geographical, political and economical environments, which should be acknowledged by the supplier when providing solutions comprising of larger and more complex scopes than previously supplied to these customers. This means that the suppliers are increasing their supply range by taking over some of the activities in the value chain that have traditionally been handled by the customer. In order to be able to provide the functioning solutions, including more engineering hours, technical equipment and a wider project network, a change is needed in the mindset in order to be able to carry out and take the required responsibility that these new approaches bring. For the supplier it is important to be able to integrate technical products, systems and services, but the supplier also needs to have the capabilities to integrate the cross-functional organizations and departments in the project network, the knowledge and information between and within these organizations and departments, along with inputs from the customer into the product and process structures during the lifecycle of the project under development. Hence, the main objective of this thesis is to explore the challenges of integration that industrial projects meet, and based on that, to suggest a concept of how to manage integration in project business by making use of integration mechanisms. Integration is considered the essential process for accomplishing an industrial project, whereas the accomplishment of the industrial project is considered to be the result of the integration. The thesis consists of an extended summary and four papers, that are based on three studies in which integration mechanisms for value creation in industrial project networks and the management of integration in project business have been explored. The research is based on an inductive approach where in particular the design, commissioning and operations functions of industrial projects have been studied, addressing entire project life-cycles. The studies have been conducted in the shipbuilding and power generation industries where the scopes of supply consist of stand-alone equipment, equipment and engineering, and turnkey solutions. These industrial solutions include demanding efforts in engineering and organization. Addressing the calls for more studies on the evolving value chains of integrated solutions, mechanisms for inter- and intra-organizational integration and subsequent value creation in project networks have been explored. The research results in thirteen integration mechanisms and a typology for integration is proposed. Managing integration consists of integrating the project network (the supplier and the sub-suppliers) and the customer (the customer’s business purpose, operations environment and the end-user) into the project by making use of integration mechanisms. The findings bring new insight into research on industrial project business by proposing integration of technology and engineering related elements with elements related to customer oriented business performance in contemporary project environments. Thirteen mechanisms for combining products and the processes needed to deliver projects are described and categorized according to the impact that they have on the management of knowledge and information. These mechanisms directly relate to the performance of the supplier, and consequently to the functioning of the solution that the project provides. This thesis offers ways to promote integration of knowledge and information during the lifecycle of industrial projects, enhancing the development towards innovative solutions in project business.

Phenolics of the Inner Bark of Silver Birch: Characterization and Intraspecific Variation

This thesis describes work related to the in-depth characterization of the phenolic compounds of silver birch (Betula pendula) inner bark. Phenolic compounds are the most ubiquitous class of plant secondary compounds. The unifying feature of this structurally diverse group is an aromatic ring containing at least one hydroxyl group. Due to the structural diversity, phenolics have various roles in the plant defense against biotic and abiotic stresses. In addition, they can confer several health-promoting properties to humans. Furthermore, the structural diversity of this class of compounds causes challenges for their analysis. The study species in the present work, silver birch, is economically the most important hard wood species in northern Europe. Its inner bark contains a high level of phenolic compounds and it has shown one of the strongest antioxidant activities among 92 Finnish plant materials. The literature review surveys the diversity and organ specific distribution of phenolic compounds in silver birch as well as the proposed ecological functions of phenolic compounds in nature. In addition, the basis for the characterization of phenolics by mass spectrometry (MS), nuclear magnetic resonance spectroscopy (NMR), and circular dichroism spectroscopy (CD) are reviewed. The objective of the experimental work was to extract, purify, characterize, and quantify the inner bark phenolic compounds. Overall 36 compounds were characterized by MS and ultraviolet spectroscopy (UV). 24 compounds were isolated and their structures confirmed by NMR and CD spectroscopy. Five novel natural compounds were identified. Special emphasis was placed on the establishment of a method for the characterization of proanthocyanidins (PAs). Hydrophilic interaction liquid chromatography (HILIC) was utilized because of its high resolution power and predictable elution order of oligomeric and polymeric PAs according to an increasing degree of polymerization. The combination of HILIC and high-resolution MS detection allowed the identification of procyanidin (PC) polymers up to the degree of polymerization of 22. In addition, a series of oligomeric and polymeric PC monoxylosides were observed for the first time in nature. Season and genotype influenced the quantities of the main inner bark phenolics, yet qualitative differences were not observed. However, manual wounding of the inner bark induced the production of ellagitannins (ETs) in the wounded tissues, i.e. callus. Since ETs were not detected in the intact inner bark, this finding may reflect the capacity of silver birch to exploit ellagitannins in its defense.

Pursuit of change versus organizational inertia: a study on strategic renewal in the Finnish broadcasting company

This doctoral dissertation explores the intra-organizational dynamics of a strategic renewal process. The main research question is how the pursuit of change and organizational inertia co-exist, intertwine, and collide in organizational cognition and capabilities during the strategic renewal. It is a comprehensive study on how organizational capabilities, organizational cognition, and structure enhance and inhibit change. Theoretically, the study is positioned in the modern tradition of strategy research, using the dynamic capability view and the organizational and managerial cognition research tradition as the main theoretical frames. Empirically, the study is a longitudinal case study of the Finnish Broadcasting Company (Yle), following the organizational changes during the years of 2011-1014. The analysis is based on both quantitative and qualitative data, which was collected during the research process using surveys, interviews, and archives. The main theoretical contribution is the application of the two theoretical approaches in one study. Empirically, the study contributes to operationalization of the concepts related to the dynamic capability view and organizational cognition, in a media context that is going through drastic changes due to digitalization. Furthermore, the case of a public broadcasting company extends the application of the theoretical concepts to the context of public management. The results suggest that renewal is a complex process, in which an organization’s perceptions intertwine with the strategic actions and decision-making. The change evolves pathdependently: the past experiences, routines, and organizational structures tend to dictate the future visions, desires, and actions. The study also reveals how the public nature of an organization adds to the tensions between change and organizational inertia, and hampers the decision-making. The doctoral dissertation consists of six research papers, each of which explores the phenomenon under study from a different perspective.

Kognitiiviset kartat operatiivisen ketjuliiketoimintajohtamisen taustalla

Tutkimuksen tavoitteena oli selvittää, millaiset ajattelumallit korostuvat menestyksekkäässä ketjuliiketoimintajohtamisessa tasapainotetun tuloskortin eri näkökulmien osalta. Tutkimuskohteena olivat kuusi päivittäistavarakaupan ketjuliiketoiminnan asiakasrajapinnassa työskentelevää Osuuskauppa Keskimaan S-marketpäällikköä. Ajattelua tutkittiin kognitiivisesta näkökulmasta. Tutkimus toteutettiin laadullista tutkimusmenetelmää, kognitiivista kartoitusta hyödyntäen. Karttojen rakentamiseen käytetty tutkimusaineisto hankittiin puolistrukturoitujen teemahaastattelujen avulla. Tutkimuksen teoreettinen viitekehys rakennettiin mielen sisäisten skeemojen ja kognitiivisten karttojen kautta päätöksenteonteorioihin. Tutkimuksen tulosten perusteella asiakasnäkökulmassa menestyminen edellyttää liikeideaa kunnioittavaa ja konseptin tinkimättömään toteuttamiseen keskittyvää johtamisajattelua. Henkilöstönäkökulmassa menestyminen korostaa kokonaisvaltaisen esimiestyön ja moniulotteisten vuorovaikutussuhteiden merkitystä, joiden ilmeneminen on kognitiivisia rakenteita ja prosesseja monimuotoisempi kokonaisuus. Prosessinäkökulmassa menestyminen edellyttää selkeiden ohjeiden vaalimiseen ja niiden johtamiseen keskittyvää ajattelutapaa. Menestys talousnäkökulmassa kokoaa tuloskortin eri näkökulmat yhteen, korostaen kokonaisuuden hahmottamisen tärkeyttä sekä toimialan ja ketjuliiketoiminnan business-logiikan ymmärtämisen merkitystä osana operatiivista ketjuliiketoimintajohtamista. Lisäksi tutkimus vahvistaa aiempien tutkimustulosten mukaisesti, että kognitiivisen kartan rikkaudella, yhtenäisyydellä, johdonmukaisuudella, kartan sisältämien suorituskykymittareihin viittaavien mainintojen määrällä sekä esimiehen kokemalla vaikutusmahdollisuudella on yhteys liiketoimintamenestyksen kanssa. Kokonaisuutena päivittäistavarakaupan ketjuliiketoiminnan menestyksekkäässä johtamisessa näyttää korostuvan rationaalisuutta ja loogisuutta korostava ajattelutapa, joka tukeutuu vahvasti ketjuliiketoiminnan perusprosesseihin.