Collective Memory Embodied in Poetry as Poison. The Mnemonic Role of Romantic Poets Discussed on the Basis of Adam Mickiewicz’ Konrad Wallenrod and Forefathers (Part III)

This thesis constitutes an interdisciplinary approach to the Polish Romanticism combining literature studies with memory studies, nationalism research and psychoanalysis. This phenomenon-based study attempts to answer the question, how the Polish national poet Adam Mickiewicz (1798–1855) – or more exactly the implied authors in his works – perceived the role of poetry in mnemonic terms and how it changes in course of time. Consequently, ‘memory in literature’ (Astrin Erll and Ansger Nünning) is discussed here. Two pieces of writing by Mickiewicz – Konrad Wallenrod [1828] and the third part of Forefathers [1832], where a bard respectively a poetic genius appears – are seen as meta-texts defining goals of poets in time of the political non-existence of a state. Poetry is supposed to keep memory of the glorious past alive, kindle the love for the motherland, support the collective identity of a group and initiate a liberation movement. Poets function as memory guards, leaders of the nation and prophets. Thus, literature is a medium of collective memory – it stores crucial contents, transmits them and acts as a cue. Nevertheless, shifting the focus from the community towards well-being of individuals, which is consistent with the postmodern thinking, the impact that poetry has on members of a given memory culture (Jan Assmann) can be described in ‘vampiric’ terms (Maria Janion). Poetry embodying collective memory may be compared to ‘poison’, ‘infecting’ people with a nationalistic way of thinking to their disadvantage as far as their personal lives are concerned.

Pyörivän keskiökärjen rakenteen kehittäminen työstövärähtelyjen välttämiseksi sorvauksessa

Tässä diplomityössä käsitellään sorvauksen työstövärähtelyjen ja sorvin keskiökärjen rakenteen yhteyttä. Työ on osa Lappeenrannan teknillisen yliopiston VMAX-projektia, ja sen taustalla on pyrkimys uudenlaisen, sorvin kärkipylkän puristusvoiman ajonaikaiseen säätämiseen perustuvan työstövärähtelyjen välttämismenetelmän kehittämiseen. Tämän menetelmän toiminnan todentaminen oli työn ensimmäinen tavoite. Menetelmän toteuttaminen asettaa kuitenkin käytetyn keskiökärjen rakenteelle tiettyjä vaatimuksia. Työn toisena tavoitteena oli nämä vaatimukset täyttävän keskiökärjen prototyypin kehittäminen. Tutkimus eteni seuraavasti. Ensimmäiseksi ongelma määriteltiin tutustumalla työn teoreettiseen taustaan ja aiheeseen liittyvään tutkimukseen Lappeenrannan teknillisestä yliopistosta ja muualta. Myös keskiökärkiä valmistavien yritysten tuotekatalogeja tarkasteltiin. Seuraavaksi siirryttiin alustavaan suunnitteluvaiheeseen, jossa verifioitiin menetelmän toiminta ja luotiin konsepteja keskiökärjen rakenteen kehittämistä varten. Tämän alustavan vaiheen jälkeen suoritettiin suunnitteluprosessi keskiökärjen prototyypille. Lopuksi, suunnitellun prototyypin rakenteen käyttäytymistä arvioitiin tietokonemallinnuksen avulla. Lisätuloksena tutkimuksen aikana johdettiin yksinkertaistettu elementtimenetelmään perustuva laskentamalli järjestelmän ominaistaajuuksien selvittämiseksi. Laskentamallin tarkkuutta arvoitiin. Suunnitteluprosessin tuloksena saatiin kaikki menetelmän toiminnan sekä normaalin käytön asettamat vaatimukset täyttävä rakenne keskiökärjen prototyypille. Myös johdetun laskentamallin tulokset ovat varsin lähellä 3D-elementtimallinnuksen antamia tuloksia. Tutkimuksen tavoitteiden voidaan siis sanoa toteutuneen. Koska prototyyppiä ja laskentamallia ei kuitenkaan ole vielä kokeellisesti verifioitu, tämä ei ole täysin varmaa.

Aircraft tracking and classification with vhf passive bistatic radar

Since the times preceding the Second World War the subject of aircraft tracking has been a core interest to both military and non-military aviation. During subsequent years both technology and configuration of the radars allowed the users to deploy it in numerous fields, such as over-the-horizon radar, ballistic missile early warning systems or forward scatter fences. The latter one was arranged in a bistatic configuration. The bistatic radar has continuously re-emerged over the last eighty years for its intriguing capabilities and challenging configuration and formulation. The bistatic radar arrangement is used as the basis of all the analyzes presented in this work. The aircraft tracking method of VHF Doppler-only information, developed in the first part of this study, is solely based on Doppler frequency readings in relation to time instances of their appearance. The corresponding inverse problem is solved by utilising a multistatic radar scenario with two receivers and one transmitter and using their frequency readings as a base for aircraft trajectory estimation. The quality of the resulting trajectory is then compared with ground-truth information based on ADS-B data. The second part of the study deals with the developement of a method for instantaneous Doppler curve extraction from within a VHF time-frequency representation of the transmitted signal, with a three receivers and one transmitter configuration, based on a priori knowledge of the probability density function of the first order derivative of the Doppler shift, and on a system of blocks for identifying, classifying and predicting the Doppler signal. The extraction capabilities of this set-up are tested with a recorded TV signal and simulated synthetic spectrograms. Further analyzes are devoted to more comprehensive testing of the capabilities of the extraction method. Besides testing the method, the classification of aircraft is performed on the extracted Bistatic Radar Cross Section profiles and the correlation between them for different types of aircraft. In order to properly estimate the profiles, the ADS-B aircraft location information is adjusted based on extracted Doppler frequency and then used for Bistatic Radar Cross Section estimation. The classification is based on seven types of aircraft grouped by their size into three classes.

Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Improving oral healthcare in Scotland with special reference to sustainability and caries prevention

Brett Duane Improving oral healthcare in Scotland with special reference to sustainability and caries prevention University of Turku, Faculty of Medicine, Institute of Dentistry, Community Dentistry, Finnish Doctoral Program in Oral Sciences (FINDOS-Turku), Turku, Finland Annales Universitatis Turkuensis, Sarja- Ser. D, Medica-Odontologica. Painosalama Oy, Turku, Finland, 2015. Dentistry must provide sustainable, evidence-based, and prevention-focused care. In Scotland oral health prevention is delivered through the Childsmile programme, with an increasing use of high concentration fluoride toothpaste (HCFT). Compared with other countries there is little knowledge of xylitol prevention. The UK government has set strict carbon emission limits with which all national health services (NHS) must comply. The purpose of these studies was firstly to describe the Scottish national oral health prevention programme Childsmile (CS), to determine if the additional maternal use of xylitol (CS+X) was more effective at affecting the early colonisation of mutans streptococci (MS) than this programme alone; secondly to analyse trends in the prescribing and management of HCFT by dentists; and thirdly to analyse data from a dental service in order to improve its sustainability. In all, 182 mother/child pairs were selected on the basis of high maternal MS levels. Motherswere randomly allocated to a CS or CS+X group, with both groups receiving Childsmile. Theintervention group consumed xylitol three times a day, from when the child was 3 months until 24 months. Children were examined at age two to assess MS levels. In order to understand patterns of HCFT prescribing, a retrospective secondary data analysis of routine prescribing data for the years 2006-2012 was performed. To understand the sustainability of dental services, carbon accounting combined a top-down approach and a process analysis approach, followed by the use of Pollard’s decision model (used in other healthcare areas) to analyse and support sustainable service reconfiguration. Of the CS children, 17% were colonised with MS, compared with 5% of the CS+X group. This difference was not statistically significant (P=0.1744). The cost of HCFT prescribing increased fourteen-fold over five years, with 4% of dentists prescribing 70% of the total product. Travel (45%), procurement (36%) and building energy (18%) all contributed to the 1800 tonnes of carbon emissions produced by the service, around 4% of total NHS emissions. Using the analytical model, clinic utilisation rates improved by 56% and patient travel halved significantly reducing carbon emissions. It can be concluded that the Childsmile programme was effective in reducing the risk for MS transmission. HCFT is increasing in Scotland and needs to be managed. Dentistry has similar carbon emissions proportionally as the overall NHS, and the use of an analytic tool can be useful in helping identify these emissions. Key words: Sustainability, carbon emissions, xylitol, mutans streptococci, fluoride toothpaste, caries prevention.