The effects of welding heat input on the usability of high strength steels in welded structures

High strength steel (HSS) has been in use in workshops since the 1980s. At that time, the significance of the term HSS differed from the modern conception as the maximum yield strength of HSSs has increased nearly every year. There are three different ways to make HSS. The first and oldest method is QT (quenched and tempered) followed by the TMCP (thermomechanical controlled process) and DQ (direct quenching) methods. This thesis consists of two parts, the first of which part introduces the research topic and discusses welded HSS structures by characterizing the most important variables. In the second part of the thesis, the usability of welded HSS structures is examined through a set of laboratory tests. The results of this study explain the differences in the usability of the welded HSSs made by the three different methods. The results additionally indicate that usage of different HSSs in the welded structures presumes that manufacturers know what kind of HSS they are welding. As manufacturers use greater strength HSSs in welded structures, the demands for welding rise as well. Therefore, during the manufacturing process, factors such as heat input, cooling time, weld quality, and more must be under careful observation.

The effect of shielding gas feeding method in laser welding of steel

Gas shielding plays an important role in laser welding phenomena. This is because it does not only provide shielding against oxidization but it has an effect in beam absorption and thus welds penetration. The goal of this thesis is to study and compare the effects of different shielding gas feeding methods in laser welding of steel. Research method is a literature survey. It is found that the inclination angle and the arrangement of the gas feeding nozzles affect the phenomena significantly. It is suggested that by designing shielding gas feeding case specifically better welding results can be obtained.

The effect of focal point parameters in fiber laser welding of structural steel

In this thesis the effect of focal point parameters in fiber laser welding of structural steel is studied. The goal is to establish relations between laser power, focal point diameter and focal point position with the resulting quality, weld-bead geometry and hardness of the welds. In the laboratory experiments, AB AH36 shipbuilding steel was welded in an I-butt joint configuration using IPG YLS-10000 continuous wave fiber laser. The quality of the welds produced were evaluated based on standard SFS-EN ISO 13919-1. The weld-bead geometry was defined from the weld cross-sections and Vickers hardness test was used to measure hardness's from the middle of the cross-sections. It was shown that all the studied focal point parameters have an effect on the quality, weld-bead geometry and hardness of the welds produced.

Nd:YAG Laser Welding of 5083 Aluminium Alloy using Filler Wire

High reflectivity and high thermal conductivity, high vapour pressure of alloyingelements as well as low liquid surface tension and low ionisation potential, make laser welding of aluminium and its alloys a demanding task.Problems that occur during welding are mainly process instabilities of the keyhole and the melt pool, increased plasma formation above the melt pool and loss of alloying elements. These problems lead to unwanted metallurgical defects like hot cracks and porosity in the weld bead andother problems concerning the shape and appearance of the weld bead. In order to minimise the defects and improve the weld quality, the process and beam parameters need to be carefully adjusted along with a consideration concerning the use of filler wire for the welding process. In this work the welding of 3,0 mm thick grade 5083 aluminium alloy plates using a 3,0 kW Nd:YAG laser with grade 5183 filler wire addition is investigated. The plates were welded as butt joints with air gap sizes 0,5 mm, 0,7mm and 1,0 mm. The analysis of the weld beads obtained from the weldedsamples showed that the least imperfections were produced with 0,7 mm air gaps at moderate welding speeds. The analysis also covered the calculation of the melting efficiency and the study of the shape of the weld bead. The melting efficiency was on average around 20 % for the melting process of the welded plates. The weld beads showed the characteristic V-shape of a laser weld and retained this shape during the whole series of experiments.

Effect of Shielding Gases in Laser Welding of Aluminium Alloys

High reflectivity to laser light, alloying element evaporation during high power laser welding makes aluminium alloys highly susceptibility to weld defects such as porosity, cracking and undercutting. The dynamic behaviour of the keyhole, due to fluctuating plasma above the keyhole and the vaporization ofthe alloying elements with in the keyhole, is the key problem to be solved for the improvement of the weld quality and stabilization of the keyhole dynamics isperhaps the single most important development that can broaden the application of laser welding of aluminium alloys. In laser welding, the shielding gas is commonly used to stabilize the welding process, to improve the welded joint features and to protect the welded seam from oxidation. The chemicalcomposition of the shielding gas is a key factor in achieving the final qualityof the welded joints. Wide range of shielding gases varying from the pure gasesto complex mixtures based on helium, argon, nitrogen and carbon dioxide are commercially available. These gas mixtures should be considered in terms of their suitability during laser welding of aluminium alloys to produce quality welds. The main objective of the present work is to study the effect of the shielding gascomposition during laser welding of aluminium alloys. Aluminium alloy A15754 was welded using 3kW Nd-YAG laser (continuous wave mode). The alloy samples were butt welded with different shielding gases (pure and mixture of gases) so that high quality welds with high joint efficiencies could be produced. It was observed that the chemical composition of the gases influenced the final weld quality and properties. In general, the mixture gases, in correct proportions, enabled better utilisation of the properties of the mixing gases, stabilized the welding process and produced better weld quality compared to the pure shielding gases.

A support system for evaluating a suitable joining method in the production of sheet metal goods

This report illustrates a comparative study of various joining methods involved in sheet metal production. In this report it shows the selection of joining methods, which includes comparing the advantages and disadvantages of a method over the other ones and choosing the best method for joining. On the basis of various joining process from references, a table is generated containing set of criterion that helps in evaluation of various sheet metal joining processes and in selecting the most suitable process for a particular product. Three products are selected and a comprehensive study of the joining methods is analyzed with the help of various parameters. The table thus is the main part of the analysis process of this study and can be advanced with the beneficial results. It helps in a better and easy understanding and comparing the various methods, which provides the foundation of this study and analysis. The suitability of the joining method for various types of cases of different sheet metal products can be tested with the help of this table. The sections of the created table display the requirements of manufacturing. The important factor has been considered and given focus in the table, as how the usage of these parameters is important in percentages according to particular or individual case. The analysis of the methods can be extended or altered by changing the parameters according to the constraint. The use of this table is demonstrated by pertaining the cases from sheet metal production.

MIG-juotto väsymiskestävyyden parantamismenetelmänä

Tässä tutkimuksessa esitellään MIG-juoton periaatteet ja tarkastellaan menetelmää siitä näkökulmasta, että menetelmä voisi toimia yhtenä varteenotettavana hitsattujen liitosten väsymiskestävyyden parantamismenetelmänä. Muiden parantamismenetelmien laajaa kirjoa esitellään lyhyesti. MIG-juoton soveltuvuutta parantamismenetelmäksi tutkittiin väsytyskokein. Kokeiden avulla määritettiin pelkästään MIG-juotetun liitoksen väsymiskestävyys erilaisissa tapauksissa. Lisäksi määritettiin väsymiskestävyys tapauksessa, jossa perinteisen MAG-pienahitsin rajaviivalle MIG-juotetiin ylimääräinen palko. Jälkimmäisessä tapauksessa menetelmä toimii väsymiskestävyyden parantamismenetelmänä. Väsytyskokeita tehtiin kaikkiaan 63 kpl.Kaikkiaan erilaisia väsytyskoesarjoja oli kymmenen, joista kuusi oli 8-10 koekappaletta käsittäviä varsinaisia tutkittavia tapauksia ja neljä pieniä, vain kaksi tai kolme koesauvaa käsittäviä pilottikoesarjoja. Koetuloksia verrattiin IIW:n(International Institute of Welding) suunnitteluohjeisiin ja suosituksiin. MIG-juotettujen liitosten väsymiskestävyys oli yleisesti ottaen hyvä. Päittäisliitosoli vähintään yhtä hyvä kuin tavanomaisesti hitsattu. Voimaa kantavassa taivutustapauksessa saatiin 110 % parempi väsymislujuus verrattuna IIW:n suunnitteluohjeeseen. Voimaa kantamattomissa poikittaisissa kiinnitysliitoksissa puolestaan saavutettiin paikallisia nimellisiä jännityksiä käyttäen 70-80 %:n parannus suunnitteluohjeeseen nähden. Pelkästään MIG-juotetun liitoksen ja 'parannetun' liitoksen väsymislujuudet olivat tässä tapauksessa likimain yhtä suuret. MIG-juottoa käytetään vaihtoehtoisena liittämismenetelmänä jo joissakin teollisissa sovelluksissa. Tämän tutkimuksen koetulokset antavat selviä viitteitä siitä, että menetelmä voisi toimia yhtenä varteenotettavana väsymiskestävyyden parantamiskeinona uusille tai korjatuille rakenteille. Vaaditaan kuitenkin vielä lisätutkimuksia, jotta menetelmää voisi soveltaa luottavaisin mielin tuotantokäytössä väsymiskestävyyden parantamismenetelmänä.

Arc : for piano and orchestra

Digitoitu 10. 6. 2008.

Musica per tredici arc[h]i

Digitoitu 11. 7. 2008.

Optimizing of intelligence level in welding

The productivity, quality and cost efficiency of welding work are critical for metal industry today. Welding processes must get more effective and this can be done by mechanization and automation. Those systems are always expensive and they have to pay the investment back. In this case it is really important to optimize the needed intelligence and this way needed automation level, so that a company will get the best profit. This intelligence and automation level was earlier classified in several different ways which are not useful for optimizing the process of automation or mechanization of welding. In this study the intelligence of a welding system is defined in a new way to enable the welding system to produce a weld good enough. In this study a new way is developed to classify and select the internal intelligence level of a welding system needed to produce the weld efficiently. This classification contains the possible need of human work and its effect to the weld and its quality but does not exclude any different welding processes or methods. In this study a totally new way is developed to calculate the best optimization for the needed intelligence level in welding. The target of this optimization is the best possible productivity and quality and still an economically optimized solution for several different cases. This new optimizing method is based on grounds of product type, economical productivity, the batch size of products, quality and criteria of usage. Intelligence classification and optimization were never earlier made by grounds of a made product. Now it is possible to find the best type of welding system needed to welddifferent types of products. This calculation process is a universal way for optimizing needed automation or mechanization level when improving productivity of welding. This study helps the industry to improve productivity, quality and cost efficiency of welding workshops.

Genesis and Emplacement of Carbonatites and Lamprophyres in the Svecofennian Domain

A small carbonatite dyke swarm has been identified at Naantali, southwest Finland. Several swarms of shoshonitic lamprophyres are also known along the Archean-Proterozoic boundary in eastern Finland and northwest Russia. These intrusions, along with the carbonatite intrusion at Halpanen, eastern Finland, represent a stage of widespread low-volume mantle-sourced alkaline magmatism in the Svecofennian Domain. Using trace element and isotope geochemistry coupled with precise geochronology from these rocks, a model is presented for the Proterozoic metasomatic evolution of the Fennoscandian subcontinental lithospheric mantle. At ~2.2-2.06 Ga, increased biological production in shallow seas linked to continental rifting, resulted in increased burial rates of organic carbon. Subduction between ~1.93-1.88 Ga returned organic carbon-enriched sediments of mixed Archean and Proterozoic provenance to the mantle. Dehydration reactions supplied water to the mantle wedge, driving arc volcanism, while mica, amphibole and carbonate were brought deeper into the mantle with the subducting slab. The cold subducted slab was heated conductively from the surrounding warm mantle, while pressures continued to gradually increase as a result of crustal thickening. The sediments began to melt in a two stage process, first producing a hydrous alkaline silicate melt, which infiltrated the mantle wedge and crystallised as metasomatic veins. At higher temperatures, carbonatite melt was produced, which preferentially infiltrated the pre-existing metasomatic vein network. At the onset of post-collisional extension, deep fault structures formed, providing conduits for mantle melts to reach the upper crust. Low-volume partial melting of the enriched mantle at depths of at least 110 km led to the formation of first carbonatitic magma and subsequently lamprophyric magma. Carbonatite was emplaced in the upper crust at Naantali at 1795.7 ± 6.8 Ma; lamprophyres along the Archean-Proterozoic boundary were emplaced between 1790.1 ± 3.3 Ma and 1781 ± 20 Ma.

Investigation of Oxygen Cutting Process in Solid-State Welding

The oxygen cutting is a thermal cutting process, in which metal is heated locally up to its ignition temperature and burnt off by oxygen blast. Oxygen cutting can be used to remove upset metal of a hollow bar occurred due to solid-state welding process. The main goal of this research was to establish a connection between oxygen blasts and mass of metal removed and relate findings to production to suggest improvements to the current process. This master´s thesis describes the designing and building of a test rig for oxygen blowing measurements. It also contains all executed tests and test results, which were carried out. There are different cutting parameters which were studied as well as their effect on cutting process. The oxygen cutting process, used in solid-state welding process, can be improved by the test results.

WiseRoot-prosessilla hitsatun päittäisliitoksen väsymislujuus

Työssä tutkittiin Kempin WiseRoot-prosessilla hitsattujen päittäisliitosten väsymiskestävyyttä laboratoriokokein ja väsymiskestävyyden mitoitusmenetelmillä. WiseRoot-hitsausprosessi on räätälöity lyhytkaariprosessi juuripalkojen hitsaukseen yhdeltä puolelta. Väsytyskoekappaleissa käytettiin eri lujuusluokan rakenneteräksiä sekä materiaalipaksuuksia. Mantsinen Group Ltd Oy hitsasi lisäksi yhdeltä ja kahdelta puolelta hitsattuja vertailukappaleita normaalilla MAG-hitsausprosessilla. Väsymismitoitus tehdään yleisesti perustuen väsymisluokkiin, joten väsytyskokeilla ja mitoitusmenetelmillä saatuja tuloksia tarkasteltiin näiden luokitusten avulla. Tuloksia vertailtiin sekä keskenään että standardeista löytyviin väsymisluokkasuosituksiin. Väsymiskestävyyden mitoitusmenetelmistä työssä käytettiin nimelliseen jännitykseen, teholliseen lovijännitykseen ja paikalliseen venymään perustuvaa menetelmää sekä murtumismekaniikkaa. Laboratoriokokeiden perusteella voidaan todeta, että WiseRoot-hitsausprosessilla on mahdollista tuottaa yhdeltä puolelta päittäisliitos, jonka väsymiskestävyys on verrattavissa kahdelta puolelta hitsattuun päittäisliitokseen. Mitoitusmenetelmillä saadut tulokset olivat pääsääntöisesti konservatiivisia verrattuna koetuloksiin. Ainoastaan paikalliseen venymään perustuvalla menetelmällä saadut väsymisluokat olivat suurempia kuin väsytyskoetulosten perusteella lasketut väsymisluokat.

Fatigue study of the fillet weld waving on weld toe and the penetration in the weld root based on the effective notch stress approach

The fatigue failure of structures under fluctuating loads in fillet weld joints raises a demand to determine the parameters related to this type of loading. In this study, the stress distribution in the susceptible area of weld toe and weld root in fillet welded models analyzed by finite element method applying FEMAP software. To avoid the geometrical singularity on the path of analytical stress analysis in the toe and root area of a weld model the effective notch stress approach applied by which a proper fictitious rounding that mostly depend on the material of structure is applied. The models with different weld toe waving width and radius are analyzed while the flank angle of weld varied in 45 and 30 degrees. The processed results shows that the waving compare to the straight weld toe makes differences in the value of stress and consequently the stress concentration factor between the tip and depth of the waves in the weld toe which helps to protect the crack of propagation and gives enough time and tools to be informed of the crack initiation in the structure during the periodical observation of structure. In the weld root study the analyses among the models with the welding penetration percentage from non-penetration to the full-penetration shows a slightly increase in the root area stress value which comparing with the stiffening effect of penetration conclude that the half-penetration can make an optimization between the stress increase and stiffening effect of deep penetration.

Rullaoikaisukoneen asetusarvojen laskeminen ja uuden oikaisukonekokonaisuuden määritys

Tämän tutkimuksen tavoitteena oli nykyisin tuotantokäytössä olevan rullaoikaisukoneen automatisointi ja uuden oikaisukonekokonaisuuden mitoitus tulevaisuuden materiaaliominaisuuksien perusteella. Automatisoinnilla on tarkoitus nykyisessä käytössä helpottaa nauhahitsaajan työtä ja lähitulevaisuudessa optimoida romutustarvetta kelojen keula- ja häntäalueilla. Uuden oikaisukonekokonaisuuden osalta työssä on määritetty rullaoikaisukoneen rullakoot, rullien keskiöetäisyys, vaadittava moottoriteho ja rullien tuennan tarve sekä erillisen hilseenmurskaimen/rullavenytysoikaisukoneen tarve peittauslinjan toiminnassa. Rullaoikaisukoneen asetusarvojen laskeminen toteutettiin ympyräkaarimenetelmää ja seurantatutkimusta käyttäen. Ensimmäisen ylärullan asetteluarvot on laskettu suorilla kaavasovelluksilla. Toisen ylärullan kohdalla oli tarpeellista tehdä laajempaa seurantatutkimusta, jotta löydettiin sellainen tapa, jolla myös sen arvot saataisiin riippuvaiseksi ensimmäisen ylärullan asetteluarvoista ja ympyränkaarimenetelmästä. Uutta oikaisukonekokonaisuutta varten suoritettujen laskelmien perusteella rullaoikaisukoneen telakokoa ja keskiöetäisyyttä on pienennettävä, moottoritehoa on kasvatettava ja työrullien tuentaa on parannettava verrattuna nykyiseen tuotantokoneeseen. Esioikaisukonetyyppisen rullaoikaisukoneen rajoittuneesta oikaisutuloksesta ja tietyillä kelalaaduilla esiintyvä erittäin luja wüstiittihilse puoltaa vahvasti erillisen hilseenmurskaimen lisäämistä peittauslinjan konekantaan.