Torrefioidun biohiilipelletin kirjallisuustutkimus ja koeajot pilottilaitoksessa

Tämä raportti käsittelee ”Torrefioidun biohiilipelletin laatu ja varastoitavuus” hankkeen tuloksia. Hankkeen tavoitteena oli tutkia torrefioidun biohiilipelletin prosessiteknologiaa, markkinoita ja tuotantokustannuksia kirjallisuustutkimusosiossa. Hankkeen päätutkimus keskittyi koeajoihin pilottilaitoksella, jossa valmistettiin biohiilipellettiä erilaisista puuraaka-aineista. Pilottilaitos oli perustettu Torrec Oy:n toimesta Etelä-Savon Energian Pursialan voimalaitoksen yhteyteen Mikkelissä ja sen tuotanto oli käynnistynyt kesällä 2014. Kaikki koe-erät valmistettiin vain käyttämällä sidonta-aineena lauhdevettä, jota oli tiivistynyt säiliön pohjalle torrefiointiprosessin aikana. Näin ollen erillistä lisäsidonta-aineita ei tarvittu, jolloin voidaan säästää tuotantokustannuksissa jatkossakin. Euroopan Unioni on asettanut 20 % tavoitteen uusiutuvien energioiden käytölle vuoteen 2020, josta biomassalla voidaan kattaa kaksi kolmannesta. Tutkimushankkeen tavoitteena oli metsään perustuvan bioenergiatuotannon lisääminen ja tuontienergian korvaaminen kotimaisella polttoaineella. Hankkeen tarkoituksena oli tutkimusanalyysien kautta kehittää uutta kilpailukykyistä teknologiavaihtoehtoa puupolttoaineiden hyödyntämiseksi. Torrefiointiteknologiaa ollaan kaupallistamassa ympäri Eurooppaa parasta aikaa ja uusia biohiilen tuotantolaitoksia on kehitteillä ja rakenteilla. Tutkimuksen tulokset osoittavat, että biohiilipelletillä on mahdollisuudet suurimittakaavaiseen energiantuotantoon laadun suhteen, kunhan sen käyttäminen tulee edullisemmaksi laitoksissa. Toisaalta, tämä kehitys vaatii tukimekanismeja valtion puolelta, jotta pelletit lähtisivät todella liikkeelle markkinoilla.

The legal framework for energy provisions in the European Union – With special regard to providing of energy provisions within the scope of Article 194(2) TFEU

The thesis interprets the caveat of Article 194(2) TFEU in order to assess the use of the Article as a legal basis for energy provisions provided by the European Union. The research subject is the Energy Title in the Treaty of the Functioning of the European Union and the possibilities of the application of the legal basis provided therein. The purpose is analysis of the possibilities for providing of provisions within the scope of the caveat found in Article 194(2) TFEU with special regard to the possibilities of providing renewable energy legislation. The purpose of the thesis is on one hand to provide an overview of the premises for providing of energy provisions in the EU, and on the other hand to analyse the Treaty text in order to determine the legal basis for energy provisions. The ultimate objective is to determine the correct legal basis for renewable energy provisions, aimed at the mitigation of climate change. According to Article 194(2) TFEU, the practice of the shared legislative powers in the field of energy are restricted by the retention of certain energy matters within the power of the Member States. The wording of the caveat containing the restrictions is open to interpretation and has been a subject of extensive discussion. Many scholars have argued that the caveat in Article 194(2) TFEU might obstruct decision-making in energy matters. This argument is contested, and the factual impact of the codification of the energy competences is analysed. The correct legal basis for energy provisions depends on the final interpretation of the text of the caveat and the level of significance of the effect of the measure. The use of Article 194(2) TFEU as a legal basis might not be the only option. There is a possibility that the legal bases within the Environmental Title might be used as legal bases for energy provisions in addition to Article 194(2) TFEU.

Hydrogen Sensor Application of Anodic Titanium Oxide Nanostructures

Hydrogen (H2) fuel cells have been considered a promising renewable energy source. The recent growth of H2 economy has required highly sensitive, micro-sized and cost-effective H2 sensor for monitoring concentrations and alerting to leakages due to the flammability and explosiveness of H2 Titanium dioxide (TiO2) made by electrochemical anodic oxidation has shown great potential as a H2 sensing material. The aim of this thesis is to develop highly sensitive H2 sensor using anodized TiO2. The sensor enables mass production and integration with microelectronics by preparing the oxide layer on suitable substrate. Morphology, elemental composition, crystal phase, electrical properties and H2 sensing properties of TiO2 nanostructures prepared on Ti foil, Si and SiO2/Si substrates were characterized. Initially, vertically oriented TiO2 nanotubes as the sensing material were obtained by anodizing Ti foil. The morphological properties of tubes could be tailored by varying the applied voltages of the anodization. The transparent oxide layer creates an interference color phenomena with white light illumination on the oxide surface. This coloration effect can be used to predict the morphological properties of the TiO2 nanostructures. The crystal phase transition from amorphous to anatase or rutile, or the mixture of anatase and rutile was observed with varying heat treatment temperatures. However, the H2 sensing properties of TiO2 nanotubes at room temperature were insufficient. H2 sensors using TiO2 nanostructures formed on Si and SiO2/Si substrates were demonstrated. In both cases, a Ti layer deposited on the substrates by a DC magnetron sputtering method was successfully anodized. A mesoporous TiO2 layer obtained on Si by anodization in an aqueous electrolyte at 5°C showed diode behavior, which was influenced by the work function difference of Pt metal electrodes and the oxide layer. The sensor enabled the detection of H2 (20-1000 ppm) at low operating temperatures (50–140°C) in ambient air. A Pd decorated tubular TiO2 layer was prepared on metal electrodes patterned SiO2/Si wafer by anodization in an organic electrolyte at 5°C. The sensor showed significantly enhanced H2 sensing properties, and detected hydrogen in the range of a few ppm with fast response/recovery time. The metal electrodes placed under the oxide layer also enhanced the mechanical tolerance of the sensor. The concept of TiO2 nanostructures on alternative substrates could be a prospect for microelectronic applications and mass production of gas sensors. The gas sensor properties can be further improved by modifying material morphologies and decorating it with catalytic materials.

The legal framework for energy provisions in the European Union – With special regard to providing of energy provisions within the scope of Article 194(2) TFEU

The thesis interprets the caveat of Article 194(2) TFEU in order to assess the use of the Article as a legal basis for energy provisions provided by the European Union. The research subject is the Energy Title in the Treaty of the Functioning of the European Union and the possibilities of the application of the legal basis provided therein. The purpose is analysis of the possibilities for providing of provisions within the scope of the caveat found in Article 194(2) TFEU with special regard to the possibilities of providing renewable energy legislation. The purpose of the thesis is on one hand to provide an overview of the premises for providing of energy provisions in the EU, and on the other hand to analyse the Treaty text in order to determine the legal basis for energy provisions. The ultimate objective is to determine the correct legal basis for renewable energy provisions, aimed at the mitigation of climate change. According to Article 194(2) TFEU, the practice of the shared legislative powers in the field of energy are restricted by the retention of certain energy matters within the power of the Member States. The wording of the caveat containing the restrictions is open to interpretation and has been a subject of extensive discussion. Many scholars have argued that the caveat in Article 194(2) TFEU might obstruct decision-making in energy matters. This argument is contested, and the factual impact of the codification of the energy competences is analysed. The correct legal basis for energy provisions depends on the final interpretation of the text of the caveat and the level of significance of the effect of the measure. The use of Article 194(2) TFEU as a legal basis might not be the only option. There is a possibility that the legal bases within the Environmental Title might be used as legal bases for energy provisions in addition to Article 194(2) TFEU.

Dynamic Modelling of Circulating Fluidized Bed Plant with Gas Turbine Repowering

Increasing amount of renewable energy source based electricity production has set high load control requirements for power grid balance markets. The essential grid balance between electricity consumption and generation is currently hard to achieve economically with new-generation solutions. Therefore conventional combustion power generation will be examined in this thesis as a solution to the foregoing issue. Circulating fluidized bed (CFB) technology is known to have sufficient scale to acts as a large grid balancing unit. Although the load change rate of the CFB unit is known to be moderately high, supplementary repowering solution will be evaluated in this thesis for load change maximization. The repowering heat duty is delivered to the CFB feed water preheating section by smaller gas turbine (GT) unit. Consequently, steam extraction preheating may be decreased and large amount of the gas turbine exhaust heat may be utilized in the CFB process to reach maximum plant electrical efficiency. Earlier study of the repowering has focused on the efficiency improvements and retrofitting to maximize plant electrical output. This study however presents the CFB load change improvement possibilities achieved with supplementary GT heat. The repowering study is prefaced with literature and theory review for both of the processes to maximize accuracy of the research. Both dynamic and steady-state simulations accomplished with APROS simulation tool will be used to evaluate repowering effects to the CFB unit operation. Eventually, a conceptual level analysis is completed to compare repowered plant performance to the state-of-the-art CFB performance. Based on the performed simulations, considerably good improvements to the CFB process parameters are achieved with repowering. Consequently, the results show possibilities to higher ramp rate values achieved with repowered CFB technology. This enables better plant suitability to the grid balance markets.

Pk-yrityksen aurinkovoimalainvestointiin vaikuttavat tekijät

Tutkielman tavoitteena on selvittää pienten ja keskisuurten yritysten aurinkovoimalainvestointiin liittyviä tekijöitä sekä erityispiirteitä. Tutkielmassa pk-yritykset on rajattu alueellisesti Etelä-Suomeen ja tekijöitä tarkastellaan investoinnin sekä päätöksenteon näkökulmasta. Keskeisenä asiana tutkielmassa on aurinkosähkömarkkinoiden nykytila sekä mahdollisuudet. Osatavoitteena on tutkia aurinkosähkön hyödyntämistä ja käyttöönottoa Suomessa sekä luoda aurinkosähkön mahdollisuuksista selkeämpi kokonaiskuva. Tutkielman tutkimusmenetelmänä käytetään laadullista tutkimusta. Tutkielma koostuu teoreettisesta katsauksesta sekä empiirisestä osuudesta. Teoreettinen osuus tarkastelee investointeja ja rahoitusvaihtoehtoja. Empiirinen osuus pitää sisällään kolmen kohdeyrityksen haastattelut. Haastattelut toteutettiin marraskuussa 2015 aurinkosähkömarkkinoilla toimiville ratkaisuntarjoajille. Haastatteluiden avulla kartoitettiin alalla toteutettujen aurinkovoimalainvestointien taustatekijöitä ja erityispiirteitä. Tutkimustuloksina havaittiin selkeitä aurinkovoimalainvestointiin vaikuttavia tekijöitä sekä muutamia erityispiirteitä. Taloudellista kannattavuutta voidaan pitää investointien lähtökohtana. Tähän vaikuttaa uusiutuvan energian investointeihin saatavilla oleva energiatuki, jolla on merkittävä vaikutus pk-yrityksen päätöksentekoon. Lisäksi ekologinen sähkön tuotanto sekä omavaraisuus nousivat haastatteluissa esiin. Johtopäätöksinä voidaan todeta aurinkosähkön sisältävän useita tekijöitä ja erityispiirteitä, joita investoijien sekä ratkaisuntarjoajien tulee ottaa huomioon. Aurinkosähkömarkkinoiden suurta potentiaalia voidaan hyödyntää tehokkaammin kehittämällä alan tiedonjakoa esille nousseiden tekijöiden ja erityispiirteiden osalta.

Aurinkosähköjärjestelmä pientaloon

Tässä kandidaatintyössä selvitetään aurinkosähköjärjestelmän rakentamisen kannattavuutta, teknisiä ratkaisuja sekä vaatimuksia pientaloon. Tutkimus suoritetaan tarkasteltavaan kiinteistöön aurinkosähköjärjestelmän teknisten ratkaisumahdollisuuksien sekä taloudellisesti kannattavimman mallin löytämiseksi. Työssä käydään läpi järjestelmän teknisten komponenttien rakennetta ja ominaisuuksia, niille määriteltyjä vaatimuksia sekä hintaa. Työssä myös simuloidaan eri voimalakokonaisuuksien tuotantoa voimalan koon optimoimiseksi kohteelle. Saatujen tulosten perusteella voimalan hankkiminen on vielä kallista ja takaisinmaksuajat pitkiä johtuen järjestelmän kalliista hinnasta. Tulevaisuudessa aurinkosähkö tulee olemaan kannattava investointi samalla, kun yhä enenevissä määrin energistyvässä maailmassa luovutaan fossiilisista polttoaineista niiden ympäristövaikutusten ja resurssien puutteen vuoksi. Aurinkosähkö on yksi potentiaalisista korvaajista tulevaisuudessa ja voimme odottaa järjestelmien hintojen laskevan kilpailun lisääntyessä. Myös valtion tuki tulevaisuudessa on mahdollinen pientuottajillekin.

Optimal Recycling Combination of Ash in South-East Finland

The present world energy production is heavily relying on the combustion of solid fuels like coals, peat, biomass, municipal solid waste, whereas the share of renewable fuels is anticipated to increase in the future to mitigate climate change. In Finland, peat and wood are widely used for energy production. In any case, the combustion of solid fuels results in generation of several types of thermal conversion residues, such as bottom ash, fly ash, and boiler slag. The predominant residue type is determined by the incineration technology applied, while its composition is primarily relevant to the composition of fuels combusted. An extensive research has been conducted on technical suitability of ash for multiple recycling methods. Most of attention was drawn to the recycling of the coal combustion residues, as coal is the primary solid fuel consumed globally. The recycling methods of coal residues include utilization in a cement industry, in concrete manufacturing, and mine backfilling, to name few. Biomass combustion residues were also studied to some extent with forest fertilization, road construction, and road stabilization being the predominant utilization options. Lastly, residues form municipal solid waste incineration attracted more attention recently following the growing number of waste incineration plants globally. The recycling methods of waste incineration residues are the most limited due to its hazardous nature and varying composition, and include, among others, landfill construction, road construction, mine backfilling. In the study, environmental and economic aspects of multiple recycling options of thermal conversion residues generated within a case-study area were studied. The case-study area was South-East Finland. The environmental analysis was performed using an internationally recognized methodology — life cycle assessment. Economic assessment was conducted applying a widely used methodology — cost-benefit analysis. Finally, the results of the analyses were combined to enable easier comparison of the recycling methods. The recycling methods included the use of ash in forest fertilization, road construction, road stabilization, and landfill construction. Ash landfilling was set as a baseline scenario. Quantitative data about the amounts of ash generated and its composition was obtained from companies, their environmental reports, technical reports and other previously published literature. Overall, the amount of ash in the case-study area was 101 700 t. However, the data about 58 400 t of fly ash and 35 100 t of bottom ash and boiler slag were included in the study due to lack of data about leaching of heavy metals in some cases. The recycling methods were modelled according to the scientific studies published previously. Overall, the results of the study indicated that ash utilization for fertilization and neutralization of 17 600 ha of forest was the most economically beneficial method, which resulted in the net present value increase by 58% compared to ash landfilling. Regarding the environmental impact, the use of ash in the construction of 11 km of roads was the most attractive method with decreased environmental impact of 13% compared to ash landfilling. The least preferred method was the use of ash for landfill construction since it only enabled 11% increase of net present value, while inducing additional 1% of negative impact on the environment. Therefore, a following recycling route was proposed in the study. Where possible and legally acceptable, recycle fly and bottom ash for forest fertilization, which has strictest requirements out of all studied methods. If the quality of fly ash is not suitable for forest fertilization, then it should be utilized, first, in paved road construction, second, in road stabilization. Bottom ash not suitable for forest fertilization, as well as boiler slag, should be used in landfill construction. Landfilling should only be practiced when recycling by either of the methods is not possible due to legal requirements or there is not enough demand on the market. Current demand on ash and possible changes in the future were assessed in the study. Currently, the area of forest fertilized in the case-study are is only 451 ha, whereas about 17 600 ha of forest could be fertilized with ash generated in the region. Provided that the average forest fertilizing values in Finland are higher and the area treated with fellings is about 40 000 ha, the amount of ash utilized in forest fertilization could be increased. Regarding road construction, no new projects launched by the Center of Economic Development, Transport and the Environment in the case-study area were identified. A potential application can be found in the construction of private roads. However, no centralized data about such projects is available. The use of ash in stabilization of forest roads is not expected to increased in the future with a current downwards trend in the length of forest roads built. Finally, the use of ash in landfill construction is not a promising option due to the reducing number of landfills in operation in Finland.

Improvement of Energy Efficiency in a Gold Mining Industry: Case Study of a Russian Gold Mining Company

The issue of energy efficiency is attracting more and more attention of academia, business and policy makers worldwide due to increasing environmental concerns, depletion of non-renewable energy resources and unstable energy prices. The significant importance of energy efficiency within gold mining industry is justified by considerable energy intensity of this industry as well as by the high share of energy costs in the total operational costs. In the context of increasing industrial energy consumption energy efficiency improvement may provide significant energy savings and reduction of CO2 emission that is highly important in order to contribute to the global goal of sustainability. The purpose of this research is to identify the ways of energy efficiency improvement relevant for a gold mining company. The study implements single holistic case study research strategy focused on a Russian gold mining company. The research involves comprehensive analysis of company’s energy performance including analysis of energy efficiency and energy management practices. This study provides following theoretical and managerial contributions. Firstly, it proposes a methodology for comparative analysis of energy performance of Russian and foreign gold mining companies. Secondly, this study provides comprehensive analysis of main energy efficiency challenges relevant for a Russian gold mining company. Finally, in order to overcome identified challenges this research conceives a guidance for a gold mining company for implementation of energy management system based on the ISO standard.

Evaluation of the main energy scenarios for the global energy transition

Energy scenarios are used as a tool to examine credible future states and pathways. The one who constructs a scenario defines the framework in which the possible outcomes exist. The credibility of a scenario depends on its compatibility with real world experiences, and on how well the general information of the study, methodology, and originality and processing of data are disclosed. In the thesis, selected global energy scenarios’ transparency and desirability from the society’s point of view were evaluated based on literature derived criteria. The global energy transition consists of changes to social conventions and economic development in addition to technological development. Energy solutions are economic and ethical choices due to far-reaching impacts of energy decision-making. Currently the global energy system is mostly based on fossil fuels, which is unsustainable over the long-term due to various reasons: negative climate change impacts, negative health impacts, depletion of fossil fuel reserves, resource-use conflicts with water management and food supply, loss of biodiversity, challenge to preserve ecosystems and resources for future generations, and inability of fossil fuels to provide universal access to modern energy services. Nuclear power and carbon capture and storage cannot be regarded as sustainable energy solutions due to their inherent risks and required long-term storage. The energy transition is driven by a growing energy demand, decreasing costs of renewables, modularity and scalability of renewable technologies, macroeconomic benefits of using renewables, investors’ risk awareness, renewable energy related attractive business opportunities, almost even distribution of solar and wind resources on the planet, growing awareness of the planet’s environmental status, environmental movements and tougher environmental legislation. Many of the investigated scenarios identified solar and wind power as a backbone for future energy systems. The scenarios, in which the solar and wind potentials were deployed in largest scale, met best the set out sustainability criteria. In future research, energy scenarios’ transparency can be improved by better disclosure on who has ordered the study, clarifying the funding, clearly referencing to used sources and indicating processed data, and by exploring how variations in cost assumptions and deployment of technologies influence on the outcomes of the study.

Screening of power to gas projects

The purpose of this thesis was the screening of power to gas projects worldwide and reviewing the technologies used and applications for the end products. This study focuses solely on technical solutions and feasibility, economical profitability is excluded. With power grids having larger penetrations of intermittent sources such as solar and wind power, the demand and production cannot be balanced in conventional methods. Technologies for storing electric power in times of surplus production are needed, and the concept called power to gas is a solution for this problem. A total of 57 projects mostly located in Europe were reviewed by going through publications, presentations and project web pages. Hydrogen is the more popular end product over methane. Power to gas is a viable concept when power production from intermittent sources needs to be smoothed and time shifted, when carbon free fuels are produced for vehicles and when chemical industry needs carbon neutral raw materials.

Litiumin talteenotto luonnon suola-altaista ionisilla nesteillä

Uusiutuvan energian käytön lisääntyminen lisää sähkön varastoinnin tarvetta. Litiumioniakku-jen on todettu olevan oivallisia keinoja varastoida sähköä esimerkiksi sähköautojen energian-lähteeksi. Tästä syystä akkujen kysyntä kasvaa nopeaa tahtia, jolloin nykyiset litiumlähteet ei-vät enää riitä tuottamaan tarpeeksi litiumia kasvavaan tarpeeseen. Tämän vuoksi litiumin tal-teenottoon tulee valjastaa uusia litiumin lähteitä, joiden hyödynnettävyys nykyisellä tekniikalla on pienen litiumkonsentraation ja muiden alkali- ja maa-alkalimetallien läsnäolon takia vaikeaa. Tällä hetkellä litiumia otetaan talteen eniten korkean litiumpitoisuuden luonnon suolajärvistä. Nykyisin käytössä oleva litiumin erotusprosessi on hidas ja sen käyttö pienten litiumkonsent-raatioiden suola-altailla on kannattamatonta. Tehokkaampana talteenottomenetelmänä luonnon suolajärvillä nähdään litiumin selektiivinen uutto ionisilla nesteillä. Menetelmä on todettu toi-mivaksi suolajärvillä, joilla on matala litiumkonsentraatio. Uusien suolajärvien käyttöönotto ei ratkaise kaikkia litiumin talteenottoon liittyviä ongelmia, sillä suolajärvet ovat alttiita ilmastonmuutokselle, eikä niiden litiumvarannot ole ehtymättömät. Merien litiumvarantoja sen sijaan pidetään lähes ehtymättöminä. Litiumin talteenotto meristä on mahdollista ionisia nesteitä ja membraaneja hyödyntävällä elektrodialyysilaitteistolla, jolla litiumia voidaan ottaa talteen myös hyvin pienistä pitoisuuksista. Lisäksi on mahdollista, että litiumin talteenottoon yhdistetään juomaveden valmistus. Tällainen vedenpuhdistusprosessi olisi myös hyvä kestävän kehityksen näkökulmasta.

Dynamic model development of adiabatic compressed air energy storage

The share of variable renewable energy in electricity generation has seen exponential growth during the recent decades, and due to the heightened pursuit of environmental targets, the trend is to continue with increased pace. The two most important resources, wind and insolation both bear the burden of intermittency, creating a need for regulation and posing a threat to grid stability. One possibility to deal with the imbalance between demand and generation is to store electricity temporarily, which was addressed in this thesis by implementing a dynamic model of adiabatic compressed air energy storage (CAES) with Apros dynamic simulation software. Based on literature review, the existing models due to their simplifications were found insufficient for studying transient situations, and despite of its importance, the investigation of part load operation has not yet been possible with satisfactory precision. As a key result of the thesis, the cycle efficiency at design point was simulated to be 58.7%, which correlated well with literature information, and was validated through analytical calculations. The performance at part load was validated against models shown in literature, showing good correlation. By introducing wind resource and electricity demand data to the model, grid operation of CAES was studied. In order to enable the dynamic operation, start-up and shutdown sequences were approximated in dynamic environment, as far as is known, the first time, and a user component for compressor variable guide vanes (VGV) was implemented. Even in the current state, the modularly designed model offers a framework for numerous studies. The validity of the model is limited by the accuracy of VGV correlations at part load, and in addition the implementation of heat losses to the thermal energy storage is necessary to enable longer simulations. More extended use of forecasts is one of the important targets of development, if the system operation is to be optimised in future.

Liquid-phase alcohol promoted methanol synthesis from CO2 and H2

Methanol is an important and versatile compound with various uses as a fuel and a feedstock chemical. Methanol is also a potential chemical energy carrier. Due to the fluctuating nature of renewable energy sources such as wind or solar, storage of energy is required to balance the varying supply and demand. Excess electrical energy generated at peak periods can be stored by using the energy in the production of chemical compounds. The conventional industrial production of methanol is based on the gas-phase synthesis from synthesis gas generated from fossil sources, primarily natural gas. Methanol can also be produced by hydrogenation of CO2. The production of methanol from CO2 captured from emission sources or even directly from the atmosphere would allow sustainable production based on a nearly limitless carbon source, while helping to reduce the increasing CO2 concentration in the atmosphere. Hydrogen for synthesis can be produced by electrolysis of water utilizing renewable electricity. A new liquid-phase methanol synthesis process has been proposed. In this process, a conventional methanol synthesis catalyst is mixed in suspension with a liquid alcohol solvent. The alcohol acts as a catalytic solvent by enabling a new reaction route, potentially allowing the synthesis of methanol at lower temperatures and pressures compared to conventional processes. For this thesis, the alcohol promoted liquid phase methanol synthesis process was tested at laboratory scale. Batch and semibatch reaction experiments were performed in an autoclave reactor, using a conventional Cu/ZnO catalyst and ethanol and 2-butanol as the alcoholic solvents. Experiments were performed at the pressure range of 30-60 bar and at temperatures of 160-200 °C. The productivity of methanol was found to increase with increasing pressure and temperature. In the studied process conditions a maximum volumetric productivity of 1.9 g of methanol per liter of solvent per hour was obtained, while the maximum catalyst specific productivity was found to be 40.2 g of methanol per kg of catalyst per hour. The productivity values are low compared to both industrial synthesis and to gas-phase synthesis from CO2. However, the reaction temperatures and pressures employed were lower compared to gas-phase processes. While the productivity is not high enough for large-scale industrial operation, the milder reaction conditions and simple operation could prove useful for small-scale operations. Finally, a preliminary design for an alcohol promoted, liquid-phase methanol synthesis process was created using the data obtained from the experiments. The demonstration scale process was scaled to an electrolyzer unit producing 1 Nm3 of hydrogen per hour. This Master’s thesis is closely connected to LUT REFLEX-platform.

LM-vesiturbiinin tuotteistaminen

Tämän työn tarkoituksena on kehittää LM-vesiturbiini tuotantoon soveltuvaksi, käytöltään pitkäikäiseksi ja helposti huollettavaksi tuotesarjaksi. Työn ohjaavana runkona on käytetty VDI-Richtlinie 2221: 'Kehitystyön ja konstruoinnin yleinen kulku', mukaista järjestelmää. Lisäksi on käytetty valmistuksellista modulointia tuotteen osien suunnittelussa. Erityisesti on huomioitu tuotteen koko elinkaaren aikaiset kustannukset (LCC) ja sen vaatimukset mitoitukseen. LM-vesiturbiinistaon kehitetty kolmen erikokoisen laitteiston tuotesarja. Tuoteperheen yksittäisistä sylinteriryhmistä voidaan koota joustavasti erikokoisia ja -tehoisia energiantuotantoyksiköitä, jotka soveltuvat käyttöön hyvin pieniinkin virtauksiin ja putouskorkeuksiin. Piensarjatuotantoon hyvin soveltuvat materiaalit on valittu silmälläpitäen mahdollisimman edullista kokonaiskustannusta. Kiertomäntä laitteiston toiminnan kannalta tärkeimpänä ja siten vaativimpana osana on edellyttänyt laserhitsausta ja -leikkausta sekä koekappaleiden valmistusta, joiden perusteellalopulliseen rakenteeseen on päädytty. Mitoitus perustuu perinteisiin lujuuslaskentamenetelmiin, joiden avulla eri osien kestävyys käyttöolosuhteissa on pyrittysaamaan luotettavaksi vähintään 20 vuoden kestoiälle ja väsymiskestävyyteen käytön aikaisissa vaihtelevissa olosuhteissa. Kiertomäntä on ns. kevytrakenne koostuen ohutlevykennorakenteesta ja täytteenä olevasta kompound-materiaalista.