Shell moottoriöljyjä

kuv., 12 x 19 cm

Experimental and discrete element simulation studies of bell-less charging of blast furnace

This thesis presents an experimental study and numerical study, based on the discrete element method (DEM), of bell-less charging in the blast furnace. The numerical models are based on the microscopic interaction between the particles in the blast furnace charging process. The emphasis is put on model validation, investigating several phenomena in the charging process, and on finding factors that influence the results. The study considers and simulates size segregation in the hopper discharging process, particle flow and behavior on the chute, which is the key equipment in the charging system, using mono-size spherical particles, multi-size spheres and nonspherical particles. The behavior of the particles at the burden surface and pellet percolation into a coke layer is also studied. Small-scale experiments are used to validate the DEM models.

Technology park as an element of innovative infrastructure- its role in internationalization support.

The Thesis concentrates on two central terms – Technology park and the resource-based view of the organization. General attention is devoted to competencies and capabilities of organizations that operate in foreign environment. It is difficult to go abroad without any experience and support from local government, especially for small or medium company. Technology and Science parks are the main sources of competitive advantage for this kind of organizations. They provide a huge range of services as well as business consultations and financial support on different stages of companies’ development. The Thesis was made with the assistance of Technopolis Oy in Lappeenranta. During the research companies in Finland and Russia were interviewed. Based on empirical findings important capabilities for entering foreign market were identified and some recommendations for the Technology park were given.

Tunable lumped-element bandpass filters for Cognitive Radio application

In this thesis the design of bandpass filters tunable at 400 MHz – 800 MHz was under research. Microwave filters are vital components which provide frequency selectivity in wide variety of electronic systems operating at high frequencies. Due to the occurrence of multi-frequency bands communication and diverse applications of wireless devices, requirement of tunable filters exists. The one of potential implementation of frequency-agile filters is frontends and spectrum sensors in Cognitive Radio (CR). The principle of CR is to detect and operate at a particular available spectrum without interfering with the primary user’s signals. This new method allows improving the efficiency of utilizing allocated spectrum such as TV band (400 MHz – 800 MHz). The focus of this work is development of sufficiently compact, low cost tunable filters with quite narrow bandwidth using currently available lumped-element components and PCB board technology. Filter design, different topologies and methods of tuning of bandpass filters are considered in this work. As a result, three types of topologies of bandpass filter were simulated and realised. They use digitally tunable capacitors (DTCs) for adjusting central frequency at TV "white space" spectrum. Measurements revealed that schematics presented in this work have proper output response and filters are successfully tuned by DTCs.

Automobiili- ja maantiekartta ynnä Shell-bensiiniasemat Automobil- och landsvägskarta jämte Shell-bensinstationer

1 kartta seitsemällätoista lehdellä :, vär. ;, 20 x 22,5 cm +, 1:1000000

Numerical simulation of two-chamber plasma sources using finite element method

Numerical simulation of plasma sources is very important. Such models allows to vary different plasma parameters with high degree of accuracy. Moreover, they allow to conduct measurements not disturbing system balance.Recently, the scientific and practical interest increased in so-called two-chamber plasma sources. In one of them (small or discharge chamber) an external power source is embedded. In that chamber plasma forms. In another (large or diffusion chamber) plasma exists due to the transport of particles and energy through the boundary between chambers.In this particular work two-chamber plasma sources with argon and oxygen as active mediums were onstructed. This models give interesting results in electric field profiles and, as a consequence, in density profiles of charged particles.

Inventive design and product development of a mechanical element

The thesis is dedicated to enhancement and development of a Mechanism in Company X in order to increase its key parameters and approve its workability. Current Mechanism model is described in details. The basis of various analysis, models and theories that are reflecting the working process of the Mechanism are included in the thesis. According to these three directions of enhancements are chosen: from mechanical, tribological and conceptual points of view. As the result the list of improvements is presented. The new models of Mechanism are built. The efficiency and lifetime value are obtained in accordance with corresponding estimations. The comparative analysis confirms the necessity of conducted changes. Recommendations for the Company X specialists are represented in the thesis. Proposals for deeper research are also suggested.

Simulation and material calibration of ultra high strength steel (UHSS) S960 welded joint under static tensile test utilizing finite element method (FEM)

The aim of this work was to calibrate the material properties including strength and strain values for different material zones of ultra-high strength steel (UHSS) welded joints under monotonic static loading. The UHSS is heat sensitive and softens by heat due to welding, the affected zone is heat affected zone (HAZ). In this regard, cylindrical specimens were cut out from welded joints of Strenx® 960 MC and Strenx® Tube 960 MH, were examined by tensile test. The hardness values of specimens’ cross section were measured. Using correlations between hardness and strength, initial material properties were obtained. The same size specimen with different zones of material same as real specimen were created and defined in finite element method (FEM) software with commercial brand Abaqus 6.14-1. The loading and boundary conditions were defined considering tensile test values. Using initial material properties made of hardness-strength correlations (true stress-strain values) as Abaqus main input, FEM is utilized to simulate the tensile test process. By comparing FEM Abaqus results with measured results of tensile test, initial material properties will be revised and reused as software input to be fully calibrated in such a way that FEM results and tensile test results deviate minimum. Two type of different S960 were used including 960 MC plates, and structural hollow section 960 MH X-joint. The joint is welded by BöhlerTM X96 filler material. In welded joints, typically the following zones appear: Weld (WEL), Heat affected zone (HAZ) coarse grained (HCG) and fine grained (HFG), annealed zone, and base material (BaM). Results showed that: The HAZ zone is softened due to heat input while welding. For all the specimens, the softened zone’s strength is decreased and makes it a weakest zone where fracture happens while loading. Stress concentration of a notched specimen can represent the properties of notched zone. The load-displacement diagram from FEM modeling matches with the experiments by the calibrated material properties by compromising two correlations of hardness and strength.

Reputational Risk Management as a key element for business continuity and value maximization

This thesis reveals the topic of reputational risk management as a key element for business continuity and value maximization. The purpose of the work is to investigate reputational risk from the side of its definition, management (including legal requirements on this risk category) and measurement and to analyse reputational risk’s impact on business continuity and value maximization. To be able to do this, different respective articles, reports of financial institutions are gathered and constructive summaries and analysis are made. In order to deeply investigate the impact of reputational risk on business continuity and value maximization, it was chosen to study it from three aspects: 1) check the impact of stock valuation of 7 companies that experienced reputational catastrophe / risk, 2) analyse a case study on disagreements in management of reputational risk among case companies and impact on their respective performance, and 3) conduct a survey of financial sector companies in Liechtenstein to see how reputational risk management works in practice. The findings of the research showed a significant impact of reputation decadence on company’s value and trading volume, and showed crucial importance of post-crisis management for the company’s financial performance. The results of the qualitative research based on survey proved that companies consider reputational risk management as a one of the key elements for their business continuity and value maximization.

Sellumassan varastosäiliön rakenneanalyysi

Tämä työ käsittelee valkaistun ja valkaisemattoman sellumassan varastosäiliön tärinää ja värähtelyä. Värähtelyn seurauksena säiliön seinämän jäykisterenkaan hitsausliitokseen on syntynyt särö. Työn tavoitteena on selvittää, mikä johtaa särön syntyyn ja miten kestäväm-piä varastosäiliöitä voidaan rakentaa materiaali-, valmistus- tai rakennemuutoksien avulla. Työ alkoi tutkimalla rakennemateriaalina olevan duplex-teräksen mikrorakenteen ominai-suuksia, sekä sen hitsattavuutta ja seostamista kirjallisuustutkimuksena. Kirjallisuustutki-musta jatkettiin selvittämällä mahdollisia vaurion syntymekanismeja seinämän särölle. Työssä analysoitiin myös tehtaalla mitattuja värähtelyarvoja. Lopuksi laskettiin FE-analyysillä tyhjän varastosäiliön ominaismuodot ja -taajuudet moodianalyysillä, sekä selvi-tettiin harmonisella analyysillä pinnankorkeuden vaihtelun vaikutus siirtymävasteeseen ja kriittisiin värähtelytaajuuksiin. Varastosäiliöön kohdistuvaa värähtelyä ei ole mahdollista poistaa kokonaan, mutta väräh-telyn aiheuttamia seurauksia kyetään rajaamaan useilla keinoilla. Toimenpiteinä voivat olla ainakin seinämän materiaalin paksuuden lisääminen, jäykisteripojen lisääminen ja kriittisten sellun pinnankorkeuksien välttäminen. Kriittiseksi pinnankorkeudeksi havaittiin 40–45 %:n täyttöaste ja turvalliseksi korkeudeksi 35–38 %:n täyttöaste. Varastosäiliölle kriittisen ominaistaajuuden katsotaan syntyvän taajuuksilla 3,3–3,8 Hz ja 5,8–6,4 Hz. Sellumassa putoaa varastosäiliöön noin 2 Hz taajuudella.

Peak Force Kelvin Probe Force Microscopy Investigation of ZrO2 Nanocomposites for Hygroelectricity Power Element

ZrO2 nanocomposites were investigated considering their perspective application in hygroelectric power elements. Scanning probe microscopy (SPM) techniques allowed to visualize the surface topography and electrical properties. In this work was compared spacial charge behaviour of sample in humid and dry air conditions. Also different SPM modes were compared. Kelvin probe force microscopy (KPFM) was applied to characterize the spacial charge distribution on surface of the sample. Measurements showed, that trapped charge is not dissipated and can be manipulated with low voltages. Humidity influence on the electric potential of the sample was shown.