Key success factors and process for IT project portfolio management

The importance of Information Technology (IT) in the business environment is continuously growing. This stimulates the increase of size, complexity and number of IT projects and raises the need for IT Project Portfolio Management (IT PPM). While being actively discussed for the last few decades, IT PPM has a short history of practical implementation. This creates inconsistency in the views of different authors and provides an opportunity for additional research. As a first step, this research explores the existing studies and brings together the views of different authors on IT PPM. As a result, a high-level IT PPM Process Cycle and a set of Key Success Factors for IT PPM are proposed. IT PPM Process Cycle gives an overview of the main elements of IT PPM process, while the set of Key Success Factors provides a number of factors that should be considered during the implementation. As a second step, both theoretical deliverables are empirically tested by a case study and a survey conducted in a big multinational company. The case study is used to analyze process framework of the studied company towards the developed IT PPM Process Cycle. Subsequently, a survey was conducted among subject matter experts of the same company to evaluate the importance and relevance of the proposed Key Success Factors. Finally, this thesis concludes with findings made during the case study and provides an empirically tested selection of factors to be taken into account. These two deliverables can be used by both academics and practitioners to close the gaps in existing literature and assist in IT PPM implementation.

Integration of learning supportive applications into the development of the e-portfolio construction process

The portfolio as a means of demonstrating personal skills has lately been gaining prominence among technology students. This is partially due to the introduction of electronic portfolios, or e-portfolios. As platforms for e-portfolio management with different approaches have been introduced, the learning cycle, traditional portfolio pedagogy, and learner centricity have sometimes been forgotten, and as a result, the tools have been used for the most part as data depositories. The purpose of this thesis is to show how the construction of e-portfolios of IT students can be supported by institutions through the usage of different tools that relate to study advising, teaching, and learning. The construction process is presented as a cycle based on learning theories. Actions related to the various phases of the e-portfolio construction process are supported by the implementation of software applications. To maximize learner-centricity and minimize the intervention of the institution, the evaluated and controlled actions for these practices can be separated from the e-portfolios, leaving the construction of the e-portfolio to students. The main contributions of this thesis are the implemented applications, which can be considered to support the e-portfolio construction by assisting in planning, organizing, and reflecting activities. Eventually, this supports the students in their construction of better and more extensive e-portfolios. The implemented tools include 1) JobSkillSearcher to help students’ recognition of the demands of the ICT industry regarding skills, 2) WebTUTOR to support students’ personal study planning, 3) Learning Styles to determine students' learning styles, and 4) MyPeerReview to provide a platform on which to carry out anonymous peer review processes in courses. The most visible outcome concerning the e-portfolio is its representation, meaning that one can use it to demonstrate personal achievements at the time of seeking a job and gaining employment. Testing the tools and the selected open-source e-portfolio application indicates that the degree of richness of e-portfolio content can be increased by using the implemented applications.

Additional revenue opportunities in pulp mills and their impacts on the kraft process

Although the concept of multi-products biorefinery provides an opportunity to meet the future demands for biofuels, biomaterials or chemicals, it is not assured that its implementation would improve the profitability of kraft pulp mills. The attractiveness will depend on several factors such as mill age and location, government incentives, economy of scale, end user requirements, and how much value can be added to the new products. In addition, the effective integration of alternative technologies is not straightforward and has to be carefully studied. In this work, detailed balances were performed to evaluate possible impacts that lignin removal, hemicelluloses recovery prior to pulping, torrefaction and pyrolysis of wood residues cause on the conventional mill operation. The development of mill balances was based on theoretical fundamentals, practical experience, literature review, personal communication with technology suppliers and analysis of mill process data. Hemicelluloses recovery through pre-hydrolysis of chips leads to impacts in several stages of the kraft process. Effects can be observed on the pulping process, wood consumption, black liquor properties and, inevitably, on the pulp quality. When lignin is removed from black liquor, it will affect mostly the chemical recovery operation and steam generation rate. Since mineral acid is used to precipitate the lignin, impacts on the mill chemical balance are also expected. A great advantage of processing the wood residues for additional income results from the fact that the pulping process, pulp quality and sales are not harmfully affected. For pulp mills interested in implementing the concept of multi-products biorefinery, this work has indicated possible impacts to be considered in a technical feasibility study.

ORCiD – Membership and implementation at Chalmers University of Technology

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

DataONE Member Node Implementation Workshop

Workshop at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Susteinable steelmaking by process integration

Environmental issues, including global warming, have been serious challenges realized worldwide, and they have become particularly important for the iron and steel manufacturers during the last decades. Many sites has been shut down in developed countries due to environmental regulation and pollution prevention while a large number of production plants have been established in developing countries which has changed the economy of this business. Sustainable development is a concept, which today affects economic growth, environmental protection, and social progress in setting up the basis for future ecosystem. A sustainable headway may attempt to preserve natural resources, recycle and reuse materials, prevent pollution, enhance yield and increase profitability. To achieve these objectives numerous alternatives should be examined in the sustainable process design. Conventional engineering work cannot address all of these substitutes effectively and efficiently to find an optimal route of processing. A systematic framework is needed as a tool to guide designers to make decisions based on overall concepts of the system, identifying the key bottlenecks and opportunities, which lead to an optimal design and operation of the systems. Since the 1980s, researchers have made big efforts to develop tools for what today is referred to as Process Integration. Advanced mathematics has been used in simulation models to evaluate various available alternatives considering physical, economic and environmental constraints. Improvements on feed material and operation, competitive energy market, environmental restrictions and the role of Nordic steelworks as energy supplier (electricity and district heat) make a great motivation behind integration among industries toward more sustainable operation, which could increase the overall energy efficiency and decrease environmental impacts. In this study, through different steps a model is developed for primary steelmaking, with the Finnish steel sector as a reference, to evaluate future operation concepts of a steelmaking site regarding sustainability. The research started by potential study on increasing energy efficiency and carbon dioxide reduction due to integration of steelworks with chemical plants for possible utilization of available off-gases in the system as chemical products. These off-gases from blast furnace, basic oxygen furnace and coke oven furnace are mainly contained of carbon monoxide, carbon dioxide, hydrogen, nitrogen and partially methane (in coke oven gas) and have proportionally low heating value but are currently used as fuel within these industries. Nonlinear optimization technique is used to assess integration with methanol plant under novel blast furnace technologies and (partially) substitution of coal with other reducing agents and fuels such as heavy oil, natural gas and biomass in the system. Technical aspect of integration and its effect on blast furnace operation regardless of capital expenditure of new operational units are studied to evaluate feasibility of the idea behind the research. Later on the concept of polygeneration system added and a superstructure generated with alternative routes for off-gases pretreatment and further utilization on a polygeneration system producing electricity, district heat and methanol. (Vacuum) pressure swing adsorption, membrane technology and chemical absorption for gas separation; partial oxidation, carbon dioxide and steam methane reforming for methane gasification; gas and liquid phase methanol synthesis are the main alternative process units considered in the superstructure. Due to high degree of integration in process synthesis, and optimization techniques, equation oriented modeling is chosen as an alternative and effective strategy to previous sequential modelling for process analysis to investigate suggested superstructure. A mixed integer nonlinear programming is developed to study behavior of the integrated system under different economic and environmental scenarios. Net present value and specific carbon dioxide emission is taken to compare economic and environmental aspects of integrated system respectively for different fuel systems, alternative blast furnace reductants, implementation of new blast furnace technologies, and carbon dioxide emission penalties. Sensitivity analysis, carbon distribution and the effect of external seasonal energy demand is investigated with different optimization techniques. This tool can provide useful information concerning techno-environmental and economic aspects for decision-making and estimate optimal operational condition of current and future primary steelmaking under alternative scenarios. The results of the work have demonstrated that it is possible in the future to develop steelmaking towards more sustainable operation.

Business-Oriented IT Tool Development For Service Delivery Process

The target of this thesis is to evaluate a bid, project and resource management IT tool for service delivery process via proof-of-concept (POC) project to assess, if the tested software is an appropriate tool for the Case Company’s business requirements. Literature suggests that IT projects implementation is still a grey area in scientific research. Also, IT projects have a notably high rate of failure, one significant reason for this being insufficient planning. To tackle this risk, the Case Company decided to perform a POC project, which involved a hands-on testing period of the assessed system. End users from the business side feel that current, highly tailored project management tool is inflexible, difficult to use, and sets unnecessary limitations for the business. Semi-structured interviews and a survey form are used to collect information about current business practices and business requirements related to the IT tool. For the POC project, a project group involving members from each of the Case Company’s four business divisions was established to perform the hands-on testing. Based on data acquired during the interviews and the hands-on testing period, a target state was defined and a gap analysis was carried out by comparing the features provided by the current tool and the tested tool to the target state, which are, together with the current state description, the most important result of the thesis.

Lean Innovation in Large Companies: a Case of Implementation in R&D

The main objective of the study is to evaluate the impact of Lean Innovation management philosophy on the creativity potential of the large multinational enterprise. A theory of Lean Innovation indicates that the modern company in any industry can successfully combine both waste-decreasing approach and innovative potential promotion through creativity cultivation or, at least, preservation. The theoretical part of the work covers the main factors, pros and cons of Lean thinking and Innovation management separately, along with generalized new product development overview. While the modern international market becomes more accessible for entrepreneural initiatives, small enterprises and start-ups, large international corporations are more subject to adopt the Lean Innovation approach in both operational and product development sectors due to extended resources and capabilities. Moreover, a multinational enterprise is a highly probable pioneer in Lean innovation implementation. The empirical part of the thesis refers to a case of large European enterprise, operating in many markets around the globe, that currently undergoes innovation management adjustments and implementations in product development while already have related themselves with operational process optimization process through Lean thinking. A goal of the work is to understand what kind of difficulties and consequences a large international firm faces when dealing with Lean Innovation to improve own performance, if they can be sealed for generalized approach.

Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Implementation of Quantitative Reaction-based Model Refinement

Building a computational model for complex biological systems is an iterative process. It starts from an abstraction of the process and then incorporates more details regarding the specific biochemical reactions which results in the change of the model fit. Meanwhile, the model’s numerical properties such as its numerical fit and validation should be preserved. However, refitting the model after each refinement iteration is computationally expensive resource-wise. There is an alternative approach which ensures the model fit preservation without the need to refit the model after each refinement iteration. And this approach is known as quantitative model refinement. The aim of this thesis is to develop and implement a tool called ModelRef which does the quantitative model refinement automatically. It is both implemented as a stand-alone Java application and as one of Anduril framework components. ModelRef performs data refinement of a model and generates the results in two different well known formats (SBML and CPS formats). The development of this tool successfully reduces the time and resource needed and the errors generated as well by traditional reiteration of the whole model to perform the fitting procedure.

Analysis and guidelines for implementation of EN 1090-2 Standard to assist execution class assignment of steel structures

Finnish design and consulting companies are delivering robust and cost-efficient steel structures solutions to a large number of manufacturing companies worldwide. Recently introduced EN 1090-2 standard obliges these companies to specify the execution class of steel structures for their customers. This however, requires clarifying, understanding and interpreting the sophisticated procedure of execution class assignment. The objective of this research is to provide a clear explanation and guidance through the process of execution class assignment for a given steel structure and to support the implementation of EN 1090-2 standard in Rejlers Oy, one of Finnish design and consulting companies. This objective is accomplished by creating a guideline for designers that elaborates on the four-step process of the execution class assignment for a steel structure or its part. Steps one to three define the consequence class (projected consequences of structure failure), the service category (hazards associated with the service use exploitation of steel structure) and the production category (manufacturing process peculiarities), based on the ductility class (capacity of structure to withstand deformations) and the behaviour factor (corresponds to structure seismic behaviour). The final step is the execution class assignment taking into account results of previous steps. Main research method is indepth literature review of European standards family for steel structures. Other research approach is a series of interviews of Rejlers Oy representatives and its clients, results of which have been used to evaluate the level of EN 1090-2 awareness. Rejlers Oy will use the developed novel coherent standard implementation guideline to improve its services and to obtain greater customer satisfaction.

Development and Effect Analysis of the Asteri Consultative Auditing Process - Safety and Security Management in Educational Institutions

The Finnish legislation requires for a safe and secure learning environment. However, the comprehensive, risk based safety and security management (SSM) and the management commitment in the implementation and development of the SSM are not mentioned in the legislation. Multiple institutions, operators and researchers have studied and developed safety and security in educational institutions over the past decade. Typically the approach has been fragmented and without bringing up the importance of the comprehensive SSM. The development needs of the safety and security operations in universities have been studied. However, in universities of applied sciences (UASs) and in elementary schools (ESs), the performance level, strengths and weaknesses of the comprehensive SSM have not been studied. The objective of this study was to develop the comprehensive, risk based SSM of educational institutions by developing the new Asteri consultative auditing process and study its effects on auditees. Furthermore, the performance level in the comprehensive SSM in UASs and ESs were studied using Asteri and the TUTOR model developed by the Keski-Uusimaa Department for Rescue Services. In addition, strengths, development needs and differences were identified. In total, 76 educational institutions were audited between the years 2011 and 2014. The study is based on logical empiricism, and an observational applied research design was used. Auditing, observation and an electronic survey were used for data collection. Statistical analysis was used to analyze the collected information. In addition, thematic analysis was used to analyze the development areas of the organizations mentioned by the respondents in the survey. As one of the main contributions, this research presents the new Asteri consultative auditing process. Organizations with low performance levels on the audited subject benefit the most from the Asteri consultative auditing process. Asteri may be usable in many different types of audits, not only in SSM audits. As a new result, this study provides new knowledge on attitudes related to auditing. According to the research findings, auditing may generate negative attitudes and the auditor should take them into account when planning and preparing for audits. Negative attitudes can be compensated by producing added value, objectivity and positivity for the audit and, thus, improve the positive effects of auditing on knowledge and skills. Moreover, as the results of this study shows, auditing safety and security issues do not increase feelings of insecurity, but rather increase feelings of safety and security when using the new Asteri consultative auditing process with the TUTOR model. The results showed that the SSM in the audited UASs was statistically significantly more advanced than that in the audited ESs. However, there is still room for improvement in the ESs and the UASs as the approach to the SSM was fragmented. It can be assumed that the majority of Finnish UASs and ESs do not likely meet the basic level of the comprehensive, risk based the SSM.

The Design and Implementation of a SD Card File System

SD card (Secure Digital Memory Card) is widely used in portable storage medium. Currently, latest researches on SD card, are mainly SD card controller based on FPGA (Field Programmable Gate Array). Most of them are relying on API interface (Application Programming Interface), AHB bus (Advanced High performance Bus), etc. They are dedicated to the realization of ultra high speed communication between SD card and upper systems. Studies about SD card controller, really play a vital role in the field of high speed cameras and other sub-areas of expertise. This design of FPGA-based file systems and SD2.0 IP (Intellectual Property core) does not only exhibit a nice transmission rate, but also achieve the systematic management of files, while retaining a strong portability and practicality. The file system design and implementation on a SD card covers the main three IP innovation points. First, the combination and integration of file system and SD card controller, makes the overall system highly integrated and practical. The popular SD2.0 protocol is implemented for communication channels. Pure digital logic design based on VHDL (Very-High-Speed Integrated Circuit Hardware Description Language), integrates the SD card controller in hardware layer and the FAT32 file system for the entire system. Secondly, the document management system mechanism makes document processing more convenient and easy. Especially for small files in batch processing, it can ease the pressure of upper system to frequently access and process them, thereby enhancing the overall efficiency of systems. Finally, digital design ensures the superior performance. For transmission security, CRC (Cyclic Redundancy Check) algorithm is for data transmission protection. Design of each module is platform-independent of macro cells, and keeps a better portability. Custom integrated instructions and interfaces may facilitate easily to use. Finally, the actual test went through multi-platform method, Xilinx and Altera FPGA developing platforms. The timing simulation and debugging of each module was covered. Finally, Test results show that the designed FPGA-based file system IP on SD card can support SD card, TF card and Micro SD with 2.0 protocols, and the successful implementation of systematic management for stored files, and supports SD bus mode. Data read and write rates in Kingston class10 card is approximately 24.27MB/s and 16.94MB/s.

Hydrometallurgical process modeling using advanced mathematical tools

Hydrometallurgical process modeling is the main objective of this Master’s thesis work. Three different leaching processes namely, high pressure pyrite oxidation, direct oxidation zinc concentrate (sphalerite) leaching and gold chloride leaching using rotating disc electrode (RDE) are modeled and simulated using gPROMS process simulation program in order to evaluate its model building capabilities. The leaching mechanism in each case is described in terms of a shrinking core model. The mathematical modeling carried out included process model development based on available literature, estimation of reaction kinetic parameters and assessment of the model reliability by checking the goodness fit and checking the cross correlation between the estimated parameters through the use of correlation matrices. The estimated parameter values in each case were compared with those obtained using the Modest simulation program. Further, based on the estimated reaction kinetic parameters, reactor simulation and modeling for direct oxidation zinc concentrate (sphalerite) leaching is carried out in Aspen Plus V8.6. The zinc leaching autoclave is based on Cominco reactor configuration and is modeled as a series of continuous stirred reactors (CSTRs). The sphalerite conversion is calculated and a sensitivity analysis is carried out so to determine the optimum reactor operation temperature and optimum oxygen mass flow rate. In this way, the implementation of reaction kinetic models into the process flowsheet simulation environment has been demonstrated.

Mobile marketing process of an international event – Case: Falun2015 FIS Nordic World Ski Championships

Any other technology has never affected daily life at this level and witnessed as speedy adaptation as the mobile phone. At the same time, mobile media has developed to be a serious marketing tool for all kinds of businesses, and the industry has grown explosively in recent years. The objective of this thesis is to inspect the mobile marketing process of an international event. This thesis is a qualitative case study. The chosen case for this thesis is the mobile marketing process of Falun2015 FIS Nordic World Ski Championships due to researcher’s interest on the topic and contacts to the people around the event. The empirical findings were acquired by conducting two interviews with three experts from the case organisation and its partner organisation. The interviews were performed as semi-structured interviews utilising the themes arising from the chosen theoretical framework. The framework distinguished six phases in the process: (i) campaign initiation, (ii) campaign design, (iii) campaign creation, (iv) permission management, (v) delivery, and (vi) evaluation and analysis. Phases one and five were not examined in this thesis because campaign initiation was not purely seen as part of the campaign implementation, and investigating phase five would have required a very technical viewpoint to the study. In addition to the interviews, some pre-established documents were exploited as a supporting data. The empirical findings of this thesis mainly follow the theoretical framework utilised. However, some modifications to the model could be made mainly related to the order of different phases. In the revised model, the actions are categorised depending on the time they should be conducted, i.e. before, during or after the event. Regardless of the categorisation, the phases can be in different order and overlapping. In addition, the business network was highly emphasised by the empirical findings and is thus added to the modified model. Five managerial recommendations can be concluded from the empirical findings of this thesis: (i) the importance of a business network should be highly valued in a mobile marketing process; (ii) clear goals should be defined for mobile marketing actions in order to make sure that everyone involved is aware them; (iii) interactivity should be perceived as part of a mobile marketing communication; (iv) enough time should be allowed for the development of a mobile marketing process in order to exploit all the potential it can offer; and (v) attention should be paid to measuring and analysing matters that are of relevance