Modulaarisen tuotteen mallivalikoiman ja tuoterakenteen keventäminen

Työn päätavoitteena on analysoida Konecranesin nosturiohjaamoperheitä ja tehdä analyysin pohjalta ehdotuksia liiketoimintayksiköiden käyttämän ohjaamovalikoiman ja modulaarisen tuoterakenteen keventämisestä. Ohjaamovalikoiman ja ohjaamojen tuoterakenteen keventämiselle on tarvetta koska laajan ohjaamovalikoiman ja monimutkaisen tuoterakenteen myötä tuotehallinta on vaikeutunut hankaloittaen myyntiprosessia ja lisäten samalla myös tuotteen tilaus-toimitusprosessin virhealttiutta ja kustannuksia. Suuren valikoiman ja monimutkaisen tuoterakenteen takia tuotekonfiguroinnissa tarvittavia teknisiä lausekkeita ei voida myöskään soveltaa kaikkiin ohjaamomalleihin ja ne ovatkin sen takia jääneet vajaakäyttöön Työn tuloksena ehdotetaan elinkaarensa päähän tulleiden ja/tai duplikaateiksi luokiteltavien mallien poistamista valikoimasta ja vain vähäistä myyntipotentiaalia omaavien tuotteiden siirtämistä erikoistuotteiden valikoimaan tarjottavaksi suunnittelua vaativina, projektiluonteisina tuotteina. Työn tuloksena ehdotetaan myös ohjaamoperheiden tuoterakenteen yhtenäistämistä ja tuotealustojen vari-oituvuuden vähentämisestä siirtämällä pienen myyntipotentiaalin omaavia alustoja projektituotteiksi.

Islandora Sync: Enabling Administrators and Developers

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

AOD 2.0: A category based submission add-on for DSpace 4.0

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Methyl and ethyl chloride synthesis in microreactors

Methyl chloride is an important chemical intermediate with a variety of applications. It is produced today in large units and shipped to the endusers. Most of the derived products are harmless, as silicones, butyl rubber and methyl cellulose. However, methyl chloride is highly toxic and flammable. On-site production in the required quantities is desirable to reduce the risks involved in transportation and storage. Ethyl chloride is a smaller-scale chemical intermediate that is mainly used in the production of cellulose derivatives. Thus, the combination of onsite production of methyl and ethyl chloride is attractive for the cellulose processing industry, e.g. current and future biorefineries. Both alkyl chlorides can be produced by hydrochlorination of the corresponding alcohol, ethanol or methanol. Microreactors are attractive for the on-site production as the reactions are very fast and involve toxic chemicals. In microreactors, the diffusion limitations can be suppressed and the process safety can be improved. The modular setup of microreactors is flexible to adjust the production capacity as needed. Although methyl and ethyl chloride are important chemical intermediates, the literature available on potential catalysts and reaction kinetics is limited. Thus the thesis includes an extensive catalyst screening and characterization, along with kinetic studies and engineering the hydrochlorination process in microreactors. A range of zeolite and alumina based catalysts, neat and impregnated with ZnCl2, were screened for the methanol hydrochlorination. The influence of zinc loading, support, zinc precursor and pH was investigated. The catalysts were characterized with FTIR, TEM, XPS, nitrogen physisorption, XRD and EDX to identify the relationship between the catalyst characteristics and the activity and selectivity in the methyl chloride synthesis. The acidic properties of the catalyst were strongly influenced upon the ZnCl2 modification. In both cases, alumina and zeolite supports, zinc reacted to a certain amount with specific surface sites, which resulted in a decrease of strong and medium Brønsted and Lewis acid sites and the formation of zinc-based weak Lewis acid sites. The latter are highly active and selective in methanol hydrochlorination. Along with the molecular zinc sites, bulk zinc species are present on the support material. Zinc modified zeolite catalysts exhibited the highest activity also at low temperatures (ca 200 °C), however, showing deactivation with time-onstream. Zn/H-ZSM-5 zeolite catalysts had a higher stability than ZnCl2 modified H-Beta and they could be regenerated by burning the coke in air at 400 °C. Neat alumina and zinc modified alumina catalysts were active and selective at 300 °C and higher temperatures. However, zeolite catalysts can be suitable for methyl chloride synthesis at lower temperatures, i.e. 200 °C. Neat γ-alumina was found to be the most stable catalyst when coated in a microreactor channel and it was thus used as the catalyst for systematic kinetic studies in the microreactor. A binder-free and reproducible catalyst coating technique was developed. The uniformity, thickness and stability of the coatings were extensively characterized by SEM, confocal microscopy and EDX analysis. A stable coating could be obtained by thermally pretreating the microreactor platelets and ball milling the alumina to obtain a small particle size. Slurry aging and slow drying improved the coating uniformity. Methyl chloride synthesis from methanol and hydrochloric acid was performed in an alumina-coated microreactor. Conversions from 4% to 83% were achieved in the investigated temperature range of 280-340 °C. This demonstrated that the reaction is fast enough to be successfully performed in a microreactor system. The performance of the microreactor was compared with a tubular fixed bed reactor. The results obtained with both reactors were comparable, but the microreactor allows a rapid catalytic screening with low consumption of chemicals. As a complete conversion of methanol could not be reached in a single microreactor, a second microreactor was coupled in series. A maximum conversion of 97.6 % and a selectivity of 98.8 % were reached at 340°C, which is close to the calculated values at a thermodynamic equilibrium. A kinetic model based on kinetic experiments and thermodynamic calculations was developed. The model was based on a Langmuir Hinshelwood-type mechanism and a plug flow model for the microreactor. The influence of the reactant adsorption on the catalyst surface was investigated by performing transient experiments and comparing different kinetic models. The obtained activation energy for methyl chloride was ca. two fold higher than the previously published, indicating diffusion limitations in the previous studies. A detailed modeling of the diffusion in the porous catalyst layer revealed that severe diffusion limitations occur starting from catalyst coating thicknesses of 50 μm. At a catalyst coating thickness of ca 15 μm as in the microreactor, the conditions of intrinsic kinetics prevail. Ethanol hydrochlorination was performed successfully in the microreactor system. The reaction temperature was 240-340°C. An almost complete conversion of ethanol was achieved at 340°C. The product distribution was broader than for methanol hydrochlorination. Ethylene, diethyl ether and acetaldehyde were detected as by-products, ethylene being the most dominant by-product. A kinetic model including a thorough thermodynamic analysis was developed and the influence of adsorbed HCl on the reaction rate of ethanol dehydration reactions was demonstrated. The separation of methyl chloride using condensers was investigated. The proposed microreactor-condenser concept enables the production of methyl chloride with a high purity of 99%.

The early activities of front end of innovation in oem companies using a new fei platform as a framework for renewal

The main goal of this study is to create a seamless chain of actions and more detailed structure to the front end of innovation to be able to increase the front end performance and finally to influence the renewal of companies. The main goal is achieved through by the new concept of an integrated model of early activities of FEI leading to a discovery of new elements of opportunities and the identification of new business and growth areas. The procedure offers one possible solution to a dynamic strategy formation process in innovation development cycle. In this study the front end of innovation is positioned between a strategy reviews and a concept creation with needed procedures, tools, and frameworks. The starting point of the study is that the origins of innovation are not well enough understood. The study focuses attention on the early activities of FEI. These first activities are conceptualized in order to find out successful innovation initiatives and strategic renewal agendas. A seamless chain of activities resulting in faster and more precise identification of opportunities and growth areas available on markets and inside companies is needed. Three case studies were conducted in order to study company views on available theory doctrine and to identify the first practical experiences and procedures in the beginning of the front end of innovation. Successful innovation requires focus on renewal in both internal and external directions and they should be carefully balanced for best results. Instead of inside-out mode of actions the studied companies have a strong outside-in thinking mode and they mainly co-develop their innovation initiatives in close proximity with customers i.e. successful companies are an integral part of customers business and success. Companies have tailor-made innovation processes combined their way of working linked to their business goals, and priorities of actual needs of transformation. The result of this study is a new modular FEI platform which can be configured by companies against their actual business needs and drivers. This platform includes new elements of FEI documenting an architecture presenting how the system components work together. The system is a conceptual approach from theories of emergent strategy formation, opportunity identification and creation, interpretation-analysis-experimentation triad and the present FEI theories. The platform includes new features compared to actual models of FEI. It allows managers to better understand the importance of FEI in the whole innovation development stage and FEI as a phase and procedure to discover and implement emergent strategy. An adaptable company rethinks and redirects strategy proactively from time to time. Different parts of the business model are changed to remove identified obstacles for growth and renewal which gives them avenues to find right reforms for renewal.

Hisseissä käytettävän kulmakorin tuotekehitys ja tuotteistaminen

Diplomityö käsittelee hisseissä erikoistapauksessa käytettävän kulmakorin suunnittelua ja tuotteistamista. Työ suoritetaan KONE Oyj:lle. Diplomityössä luotiin kulmakorille modulaarinen tuotearkkitehtuuri ja määritettiin korin toimitusprosessi. Työn tavoitteena oli saavuttaa 48,12% asiakkaiden mahdollisista vaatimuksista ja vähentää suunnitteluun kuluvaa aikaa aikaisemmasta 24 tunnista neljään tuntiin. Työn tavoite saavutettiin kokeneen tapauskohtaisten kulmakorien suunnittelijan kommenttien perusteella. 48,12% asiakasvaatimuksista sisällytettiin tuotemalliin konfigurointimahdollisuuksina. Työn alussa on esitelty tuotesuunnittelua, laadun hallintaa, parametrista mallinnusta, massakustomointia ja tuotetiedon hallintaa. Sen jälkeen on käsitelty kulmakorin tuotteistamisen kannalta kaikki tärkeimmät muuttujat. Tämän jälkeen kulmakorin tuotemalli suunnitellaan ja mallinnetaan systemaattisesti ylhäältä-alas –mallinnustapaa käyttäen ja luodaan osille ja kokoonpanoille valmistuskuvat. Päätyökaluna työssä käytettiin Pro/ENGINEER-ohjelmistoa. Tällä mallinnettiin parametrinen tuotemalli ja rakenteiden lujuustarkastelussa käytettiin ohjelmistoa Ansys. Työn tavoite saavutettiin analysoimalla massakustomoinnin perusteiden olennaisimmat osat ja seuraamalla analyyttistä ja systemaattista tuotekehitysprosessia. Laatua painottaen tuotearkkitehtuuri validoitiin suorittamalla rajoitettu tuotanto, joka sisälsi kolme tuotemallilla konfiguroitua kulmakoria. Yksi koreista testikasattiin Hyvinkään tehtaalla.

Designing sustainable industrial ecosystems : the case of a biogas-for-traffic solution

This thesis focuses on the development of sustainable industrial architectures for bioenergy based on the metaphors of industrial symbiosis and industrial ecosystems, which imply exchange of material and energy side-flows of various industries in order to improve sustainability of those industries on a system level. The studies on industrial symbiosis have been criticised for staying at the level of incremental changes by striving for cycling waste and by-flows of the industries ‘as is’ and leaving the underlying industry structures intact. Moreover, there has been articulated the need for interdisciplinary research on industrial ecosystems as well as the need to extend the management and business perspectives on industrial ecology. This thesis addresses this call by applying a business ecosystem and business model perspective on industrial symbiosis in order to produce knowledge on how industrial ecosystems can be developed that are sustainable environmentally and economically. A case of biogas business is explored and described in four research papers and an extended summary that form this thesis. Since the aim of the research was to produce a normative model for developing sustainable industrial ecosystems, the methodology applied in this research can be characterised as constructive and collaborative. A constructive research mode was required in order to expand the historical knowledge on industrial symbiosis development and business ecosystem development into the knowledge of what should be done, which is crucial for sustainability and the social change it requires. A collaborative research mode was employed through participating in a series of projects devoted to the development of a biogas-for-traffic industrial ecosystem. The results of the study showed that the development of material flow interconnections within industrial symbiosis is inseparable from larger business ecosystem restructuring. This included a shift in the logic of the biogas and traffic fuel industry and a subsequent development of a business ecosystem that would entail the principles of industrial symbiosis and localised energy production and consumption. Since a company perspective has been taken in this thesis, the role of an ecosystem integrator appeared as a crucial means to achieve the required industry restructuring. This, in turn, required the development of a modular and boundary-spanning business model that had a strong focus on establishing collaboration among ecosystem stakeholders and development of multiple local industrial ecosystems as part of business growth. As a result, the designed business model of the ecosystem integrator acquired the necessary flexibility in order to adjust to local conditions, which is crucial for establishing industrial symbiosis. This thesis presents a normative model for the development of a business model required for creating sustainable industrial ecosystems, which contributes to approaches at the policy-makers’ level, proposed earlier. Therefore, this study addresses the call for more research on the business level of industrial ecosystem formation and the implications for the business models of the involved actors. Moreover, the thesis increases the understanding of system innovation and innovation in business ecosystems by explicating how business model innovation can be the trigger for achieving more sustainable industry structures, such as those relying on industrial symbiosis.

Design structure matrix ja sen hyödyntäminen ohjelmistotuotannossa

Työn tarkoituksena on selvittää, miten DSM ja siihen liittyvät analyysit toimivat. Työssä selvitetään myös, miten DSM:a voidaan hyödyntää tuotekehityksessä ja ohjelmistotuotannon kohtaamissa ongelmissa. DSM-neliömatriisiin sijoitetaan tarkasteltavan kohteen osat riveihin ja kolumneihin identtisessä järjestyksessä. Matriisin soluihin merkitään osien väliset riippuvuudet, joilla selvitetään kunkin osan lähettämä ja vastaanottama data suhteessa muihin osiin. DSM-analyysissa osien järjestystä muutetaan suoritus- tai toteutusjärjestyksen mukaisesti parhaaseen järjestykseen. Osat ryhmitellään moduuleihin, jolloin esimerkiksi tuotekehitys ohjautuu automaattisesti modulaarisuuteen. Tuotekehitysprojekteihin DSM on kompaktin muodon, yksinkertaisuuden ja automaattisen järjestelyn ansiosta erinomainen työkalu, jolla voidaan mallintaa käytännössä mitä tahansa, mikä voidaan jakaa toisistaan riippuviin osiin. DSM voi vähentää projektien suunnitteluun vaadittua työmäärää ja avustaa realististen budjettien ja aikataulujen luontia suurissa projekteissa.

Cost Reduction of Permanent Magnet Synchronous Machines

Electrical machine drives are the most electrical energy-consuming systems worldwide. The largest proportion of drives is found in industrial applications. There are, however many other applications that are also based on the use of electrical machines, because they have a relatively high efficiency, a low noise level, and do not produce local pollution. Electrical machines can be classified into several categories. One of the most commonly used electrical machine types (especially in the industry) is induction motors, also known as asynchronous machines. They have a mature production process and a robust rotor construction. However, in the world pursuing higher energy efficiency with reasonable investments not every application receives the advantage of using this type of motor drives. The main drawback of induction motors is the fact that they need slipcaused and thus loss-generating current in the rotor, and additional stator current for magnetic field production along with the torque-producing current. This can reduce the electric motor drive efficiency, especially in low-speed, low-power applications. Often, when high torque density is required together with low losses, it is desirable to apply permanent magnet technology, because in this case there is no need to use current to produce the basic excitation of the machine. This promotes the effectiveness of copper use in the stator, and further, there is no rotor current in these machines. Again, if permanent magnets with a high remanent flux density are used, the air gap flux density can be higher than in conventional induction motors. These advantages have raised the popularity of PMSMs in some challenging applications, such as hybrid electric vehicles (HEV), wind turbines, and home appliances. Usually, a correctly designed PMSM has a higher efficiency and consequently lower losses than its induction machine counterparts. Therefore, the use of these electrical machines reduces the energy consumption of the whole system to some extent, which can provide good motivation to apply permanent magnet technology to electrical machines. However, the cost of high performance rare earth permanent magnets in these machines may not be affordable in many industrial applications, because the tight competition between the manufacturers dictates the rules of low-cost and highly robust solutions, where asynchronous machines seem to be more feasible at the moment. Two main electromagnetic components of an electrical machine are the stator and the rotor. In the case of a conventional radial flux PMSM, the stator contains magnetic circuit lamination and stator winding, and the rotor consists of rotor steel (laminated or solid) and permanent magnets. The lamination itself does not significantly influence the total cost of the machine, even though it can considerably increase the construction complexity, as it requires a special assembly arrangement. However, thin metal sheet processing methods are very effective and economically feasible. Therefore, the cost of the machine is mainly affected by the stator winding and the permanent magnets. The work proposed in this doctoral dissertation comprises a description and analysis of two approaches of PMSM cost reduction: one on the rotor side and the other on the stator side. The first approach on the rotor side includes the use of low-cost and abundant ferrite magnets together with a tooth-coil winding topology and an outer rotor construction. The second approach on the stator side exploits the use of a modular stator structure instead of a monolithic one. PMSMs with the proposed structures were thoroughly analysed by finite element method based tools (FEM). It was found out that by implementing the described principles, some favourable characteristics of the machine (mainly concerning the machine size) will inevitable be compromised. However, the main target of the proposed approaches is not to compete with conventional rare earth PMSMs, but to reduce the price at which they can be implemented in industrial applications, keeping their dimensions at the same level or lower than those of a typical electrical machine used in the industry at the moment. The measurement results of the prototypes show that the main performance characteristics of these machines are at an acceptable level. It is shown that with certain specific actions it is possible to achieve a desirable efficiency level of the machine with the proposed cost reduction methods.

Embedded Service Bus for Internet of Things Interoperability

Internet of Things (IoT) technologies are developing rapidly, and therefore there exist several standards of interconnection protocols and platforms. The existence of heterogeneous protocols and platforms has become a critical challenge for IoT system developers. To mitigate this challenge, few alliances and organizations have taken the initiative to build a framework that helps to integrate application silos. Some of these frameworks focus only on a specific domain like home automation. However, the resource constraints in the large proportion of connected devices make it difficult to build an interoperable system using such frameworks. Therefore, a general purpose, lightweight interoperability framework that can be used for a range of devices is required. To tackle the heterogeneous nature, this work introduces an embedded, distributed and lightweight service bus, Lightweight IoT Service bus Architecture (LISA), which fits inside the network stack of a small real-time operating system for constrained nodes. LISA provides a uniform application programming interface for an IoT system on a range of devices with variable resource constraints. It hides platform and protocol variations underneath it, thus facilitating interoperability in IoT implementations. LISA is inspired by the Network on Terminal Architecture, a service centric open architecture by Nokia Research Center. Unlike many other interoperability frameworks, LISA is designed specifically for resource constrained nodes and it provides essential features of a service bus for easy service oriented architecture implementation. The presented architecture utilizes an intermediate computing layer, a Fog layer, between the small nodes and the cloud, thereby facilitating the federation of constrained nodes into subnetworks. As a result of a modular and distributed design, the part of LISA running in the Fog layer handles the heavy lifting to assist the lightweight portion of LISA inside the resource constrained nodes. Furthermore, LISA introduces a new networking paradigm, Node Centric Networking, to route messages across protocol boundaries to facilitate interoperability. This thesis presents a concept implementation of the architecture and creates a foundation for future extension towards a comprehensive interoperability framework for IoT.

Bearing-spesific complications of total hip arthroplasty: characterization and treatment

Hip resurfacing arthroplasty (HRA) and large head metal-on-metal total arthroplasty (LDH MoM THA) gained popularity during the last decade. Adverse reaction to metal debris (ARMD) is a unique complication of metal bearings. ARMD is a complex reaction caused by metal debris from metal-on- metal bearing surfaces and from trunnion corrosion of modular junctions. We analyzed survivorship of 8059 LDH MoM THAs based on data of the Finnish Arthroplasty Register. We found relatively high short-term survivorship for some LDH MoM THAs, but there were remarkable differences between the devices studied. After some alarming reports of failing MoM THAs, we studied the first 80 patients who had received a ReCap-M2a-Magnum implant at our institution and evaluated the prevalence of ARMD. We found a high prevalence of pseudotumors, and, because of this, we discontinued the use of MoM bearings and followed up all patients with a MoM THA. Bone loss due infection, osteolysis or fracture poses a great challenge for reconstructive and fracture surgery. Onlay allografting for both revision and fracture surgery provides mechanical stability and increases bone stock. Bone loss and implant stability must be assessed preoperatively and adequately classified; this provides guidelines for the operative treatment of periprosthetic fractures and revision THA. In our studies on structural allografts union rates were high, although the rates of infections and dislocations were marked. In summary, early results of the use of LDH MoM devices were encouraging. However, the survival of the LDH MoMs varied. The prevalence of adverse reaction to metal debris was high after application of the ReCap-Magnum THA. New implants should be introduced carefully and under close surveillance by University clinics and arthroplasty registers.

Modulaarinen arkkitehtuuri tuoteperheen kehittämisessä

Modulaarisen tuotteen kehittäminen tehostaa yrityksen kilpailukykyä ja helpottaa asiakkaiden tarpeiden tyydyttämistä. Tuoteperheen edut verrattaessa massatuotantoon ovat laajempi tuotevalikoima sekä parempi tuotettavuus massaräätälöintiin verrattuna. Eri tuotevaihtoehtoja ja moduuleja on mahdollista kehittää rinnakkain. Moduloitava tuoteperhe helpottaa yrityksen eri vaiheita aina tuotteen suunnittelusta huoltotoimenpiteisiin ja lopulta tuotteen purkamiseen. Asiakkaille tärkeitä hyötyjä moduloinnin osalta ovat tuotteiden parempi laatu ja huollettavuus. Täysin uuden modulaarisen tuoteperheen kehittäminen vaatii runsaasti resursseja suunnitteluosastolla. Modulaarisessa tuotteessa suunnittelutyö voidaan kohdistaa vain tietyn moduulin kohdalle ja suunnitteluaikoja saadaan täten lyhennettyä. Tässä kandidaatintyössä tutkittiin, miten hitsausautomaatiosovelluksissa modulaarisuus on toteutettu sekä pohditaan kehityskohteita, koska hitsausautomaatiosovelluksia tuotetaan runsaasti asiakasräätälöintinä. Tarkasteltavana tuoteperheenä oli robottihitsausportaalit ja hitsaustornit.

Modularity in Health and Social Services: Perspectives on Organization and Management

Organizations that provide health and social services operate in a complex and constantly changing environment. Changes occur, for example, in ageing, technology and biotechnology, and customers’ expectations, as well as the global economic situation. Organizations typically aim to adapt the changes by introducing new organizational structures and managerial practices, such as process and lean management. Only recently has there been an interest in evaluating whether organizations providing health and social services could apply modularity in order to respond to some of the changes. The concept of modularity originates from manufacturing, but is applied in many other disciplines, such as information technology and logistics. However, thus far, the literature concerning modularity in health and social services is scarce. Therefore the purpose of this thesis is to increase understanding concerning modularity and the possibilities to apply modularity in the health and social services context. In addition, the purpose is to shed light on the viewpoints that are worth taking into account when considering the application of modularity in the health and social services context. The aim of the thesis is to analyze the way in which the modular structures are applied in the health and social services context and to analyze what advantages and possible barriers, as well as managerial concerns, might occur if modularity is applied in the health and social services context. The thesis is conducted by using multiple methods in order to provide a broad aspect to the topic. A systematic literature review provided solid ground for pre-understanding the topic and supported the formulation of the research questions. Theoretical reasoning provided a general overview of the special characteristics of the health and social services context and their effect on application of modularity. Empirical studies concentrated on managerial concerns of modularity particularly from the perspective of health and social services for the elderly. Results of the thesis reveal that structures in products, services, processes, and organizations are rather modular in health and social services. They can be decomposed in small independent units, while the challenges seem to occur especially in the compatibility of the services. It seems that health and social services managers have recognized this problem and they are increasingly paying attention to this challenge in order to enhance the flexible compatibility of services. Advantages and possible barriers of modularity are explored in this thesis, and from the theoretical perspective it could be argued that modularity seems to be beneficial in the context of health and social services. In fact, it has the potential to alleviate several of the challenges that the health and social services context is confronting. For example, modular structures could support organizations in their challenging task to respond to customers’ increasing demand for heterogeneous services. However, special characteristics of the health and social services context create barriers and provide significant challenges in application of modularity. For example, asymmetry of information, negative externalities, uncertainty of demand, and rigid regulation prevent managers from extensively drawing benefits from modularity. Results also reveal that modularity has managerial implications in health and social service. Modularity has the potential to promote and support new service development and outsourcing. Results also provide insights into network management and increases managerial understanding of different network management strategies. Standardization in health and social services is extensive due to legislation and recommendations. Modularity provides alternative paths to take an advantage of standardization while still ensuring the quality of the services. Based on this thesis, it can be concluded, both from a theoretical perspective and from empirical results concerning modularity in health and social services, that modularity might fit well and be beneficial. However, the special characteristics of the health and social services context prevent some of the benefits of modularity and complicate its application. This thesis contributes to the academic literature on the organization and management of health and social services by describing modularity as an alternative way for organizing and managing health and social services. In addition, it contributes to the literature of modularity by exploring the applicability of modularity in the context of health and social services. It also provides practical contribution to health and social services managers by evaluating the pros and cons of modularity when applied to health and social services.

Development of a New Welding Product Quality Control and Management System Model for China

The Chinese welding industry is growing every year due to rapid development of the Chinese economy. Increasingly, companies around the world are looking to use Chinese enterprises as their cooperation partners. However, the Chinese welding industry also has its weaknesses, such as relatively low quality and weak management. A modern, advanced welding management system appropriate for local socio-economic conditions is required to enable Chinese enterprises to enhance further their business development. The thesis researches the design and implementation of a new welding quality management system for China. This new system is called ‗welding production quality control management model in China‘ (WQMC). Constructed on the basis of analysis of a survey and in-company interviews, the welding management system comprises the following different elements and perspectives: a ‗Localized congenital existing problem resolution strategies‘ (LCEPRS) database, a ‗human factor designed training system‘ (HFDT) training strategy, the theory of modular design, ISO 3834 requirements, total welding management (TWM), and lean manufacturing (LEAN) theory. The methods used in the research are literature review, questionnaires, interviews, and the author‘s model design experiences and observations, i.e. the approach is primarily qualitative and phenomenological. The thesis describes the design and implementation of a HFDT strategy in Chinese welding companies. Such training is an effective way to increase employees‘ awareness of quality and issues associated with quality assurance. The study identified widely existing problems in the Chinese welding industry and constructed a LCEPRS database that can be used in efforts to mitigate and avoid common problems. The work uses the theory of modular design, TWM and LEAN as tools for the implementation of the WQMC system.

Pienet modulaariset ydinreaktorit

Tämän opinnäytetyön tavoitteena oli selvittää millaisia pieniä modulaarisia ydinvoimaloita (SMR engl. small modular reactor) on suunnitteilla ja miten pienet modulaariset kevytvesireaktorit eroavat toisen ja kolmannen sukupolven kevytvesilaitoksista. Työ tehtiin perehtymällä kirjallisuuslähteisiin ja erityisesti IAEA:n julkaisuihin ja raportteihin. SMR-laitosten suurin eroavaisuus verrattuna perinteisiin kevytvesilaitoksiin on lisääntynyt passiivinen turvallisuus. Ne voidaan suunnitella siten, ettei sähköä tai operaattoria tarvita reaktorin turvallisuuden varmistamiseksi. Lisäksi useissa SMR-reaktoreissa primääripiiri on integroitu painesäiliön sisään, mikä aiheuttaa uudenlaisia vaatimuksia reaktorisydämelle ja höyrystimille. Pienten modulaaristen voimaloiden etuina on niiden soveltuvuus pieniin sähköverkkoihin ja vaikeasti tavoitettavien alueiden energiantuotantoon. Sähköntuotannon lisäksi niitä voidaan käyttää myös lämmöntuotantoon, mikä parantaa laitosten kokonaishyötysuhdetta merkittävästi. Lisäksi SMR-laitosten erilainen kustannusrakenne tekee niistä houkuttelevan vaihtoehdon suurille ydinvoimalaitoksille, sillä pienemmät investointikustannukset alentavat sijoittajien riskejä. Lyhyemmän rakennusajan johdosta SMR-voimalat alkavat myös tuottaa voittoa suuria laitoksia nopeammalla aikataululla.