Impacts of capacity remunerative mechanisms on cross-border trade

The European ambitious targets to increase the share of renewable generation pose a challenge to the generation adequacy. Many European member states are concerned that energy-only markets alone might not be able to deliver sufficient capacity required to meet the future electricity demand and back up shortfalls of energy from renewable energy sources (RES) during periods of low wind and sun. Many EU members consider to re-design their energy-only markets and establish different forms of capacity remunerative mechanisms (CRMs) to maintain the security of supply. There is a certain concern that market design changes at the level of EU member countries might conflict with the European goal of a single market. As soon as many European markets are highly interconnected, uncoordinated CRMs might create negative crossborder effects and hinder the achievement of the Internal Electricity Market in Europe. The pros and cons of capacity markets are well examined at the national level. However, the cross-border effects of capacity markets within the European market aiming at higher integration have received less attention. This doctoral dissertation examines the cross-border effects of unilateral implementation of CRMs applying both theoretical and case study analyses. The results show that capacity remunerative mechanisms (CRMs) may cause negative cross-border effects, especially if they are implemented unilaterally.

Sähköajoneuvojen akkujen uusiokäyttö

Tässä kandidaatintyössä tutkittiin sähkö- ja hybridiajoneuvojen akkujen uusiokäyttöä. Tutkimus toteutettiin kirjallisuustyönä. Tavoitteena oli selvittää voidaanko sähkö- ja hybridiajoneuvojen akkuja uusiokäyttää, mitä ongelmia mahdollisesti uusiokäyttöön liittyy, minkälaisissa sovelluksissa käytettyjä akkuja voisi käyttää ja uusiokäytetäänkö kyseisenlaisia akkuja jo nykyään. Työssä esiteltiin myös yleisimpiä akkutekniikoita sekä niiden kierrätystä. Tutkimuksessa havaittiin, että akuissa on runsaasti kapasiteettia jäljellä ajoneuvokäytön jälkeen. Uusiokäytössä akku voi kestää jopa yhtä paljon käyttöä kuin ajoneuvokäytössä. Ongelmat uusiokäytössä liittyvät akkujen vaihtelevaan kuntoon ja kapasiteettiin. Ennen uusiokäyttöä akut tulisi tarkastaa ja jos mahdollista, poistaa huonokuntoiset ja vialliset kennot. Käytettyjen akkujen uusiokäyttöön soveltuvista laitteistoista on tehty muutamia prototyyppejä, jotka ovat teholtaan ja kapasiteetiltaan hyvin vaihtelevia. Sopivalla valvontajärjestelmällä varustettuna käytettyjä akkuja voitaneen käyttää myös olemassa olevissa, akkuja sisältävissä järjestelmissä. Käytettyjä akkuja voitaneen käyttää muun muassa uusiutuvan energian varastointiin, sähköverkon kulutushuippujen kompensointiin ja sähköajoneuvojen pikalatauksen puskurina. Etenkin litiumioniakkujen uusiokäyttö on järkevää, koska kierrätys ei ole kovin tehokasta ainakaan vielä.

Optimization of PV and battery capacity for domestic purposes

The usage of PV batteries nowadays became more and more widely spread. Due to the fact that the efficiency of modern PV is rising every year the prevalence of this source of energy is increasing. As the source of the energy is sunlight, these batteries need to be complimented by storage capacitors which will store energy for future use. Nevertheless the less the calculation of demanded amount of energy according the load and capacity of a storage battery that will keep the end consumer in work during certain time still is not overviewed. In this thesis the overall system will be considered and there will be made economic calculations for configurations of such system that will depend from the load. Also the behavior of the system in different geographical and climate conditions that influence of the amount of energy produced will be overviewed.

Improve the production capacity: A case study of Eurofins Viljavuuspalvelu Oy

In any manufacturing system, there are many factors that are affecting and limiting the capacity of the entire system. This thesis addressed a study on how to improve the production capacity in a Finnish company (Viljavuuspalvelu Oy) through different methods like bottleneck analysis, Overall Equipment Effectiveness (OEE), and Just in Time production. Four analyzing methods have been studied in order to detect the bottleneck machine in Viljavuuspalvelu Oy. The results shows that the bottleneck machine in the industrial area that constraint the production is the grinding machine while the bottleneck machine in the laboratory section is the photometry machine. In addition, the Overall Equipment Effectiveness (OEE) of the entire system of the studied case was calculated and it has been found that the OEE of the Viljavuuspalvelu Oy is 35.75%. Moreover, two methods on how to increase the OEE were studied and it was shown that either the total output of the company should be 1254 samples/shift in order to have an OEE around 85% which is considered as a world class or the Ideal run rate should be 1.45 pieces/minute. In addition, some realistic methods are applied based on the finding in this thesis to increase the OEE factor in the company and in one realistic method the % OEE has increase to 62.59%. Finally, an explanation on how to implement the Just in Time production in Viljavuuspalvelu Oy has been studied.