Kestomagneettitahtigeneraattorin kannattavuustarkastelu vesivoimalaitoksen saneerauksen yhteydessä

Työssä vertaillaan kestomagneettitahtigeneraattorin kannattavuutta suhteessa perinteiseen erillismagnetoituun tahtigeneraattoriin. Sähkön markkinahinnan nousu tulevaisuudessa, pakottaa etsimään uusia ratkaisuja jo olemassa olevien vesivoimalaitosten hyötysuhteen parantamiseksi. Hyötysuhteeseen vaikuttavat laitoksen mekaaniset ja sähköiset häviöt. Työn kohteena olevan vesivoimalaitoksen saneeraus on ajankohtainen lähivuosina, ja samalla avautuu mahdollisuus vaihtaa myös vanha erillismagnetoitu tahtigeneraattori uudempaan kestomagneeteilla toteutettuun. Työssä tarkastellaan kalliimman investoinnin kannattavuutta suhteessa kasvavaan energian tuotantoon. Tarkastelujaksolla lisääntyneen vuosituotannon osuuden rahallista arvoa verrataan investointihetken kustannuksiin. Työn edetessä havaittiin, että virtaamamäärän lisäyksellä on vahva rooli kannattavuutta laskettaessa. Pienillä virtaamilla ei saavuteta riittävää tuottoa ilman mekaanisen hyötysuhteen parantamista. Pelkästään generaattorityypin vaihto ei tällä hetkellä kannata, kun nykyisellä generaattorilla on käyttöaikaa jäljellä kymmeniä vuosia. Tilanne voi muuttua kannattavaksi esimerkiksi äkillisen generaattorivaurion myötä.

Kestomagneettitahtikonekäyttöjen erot

Permanent magnet drives with nominal power over 10 kW were not a cost-sufficient system 25 years ago due to high material expenses. The improvements in motor drives, the rise in competition and the tightening of standards and regulations have caused that the PM-drives are more and more common in the over 10 kW nominal power range. The goal of this thesis is to research the performance in relation to nominal power of a PM-drive technique that is vastly increasing its popularity in fan related devices. The studied motor technique brushless direct current drive (BLDC) consists of a voltage source inverter, permanent motor and six-step-control. The reference drive is a brushless alternating current drive (BLAC) which consists of a VSI, PM and a hysteresis control. As a conclusion there are no major obstacles that would impede the BLDC-drive technique from expanding to larger power stages. The following factors must be taken into consideration when designing a BLDC-drive: motor’s current change rate, inverter switching frequency, motor’s nominal electric frequency, phase inductance and the current handling capability of the inverter. The fluctuating material costs create instability to the end prices of PM-motors that can in the worst case lead to diminished interest towards BLDC- and PM-drives in general.

Modal testing and numerical modeling of the dynamic properties of layered sheet-steel structure

Recently, due to the increasing total construction and transportation cost and difficulties associated with handling massive structural components or assemblies, there has been increasing financial pressure to reduce structural weight. Furthermore, advances in material technology coupled with continuing advances in design tools and techniques have encouraged engineers to vary and combine materials, offering new opportunities to reduce the weight of mechanical structures. These new lower mass systems, however, are more susceptible to inherent imbalances, a weakness that can result in higher shock and harmonic resonances which leads to poor structural dynamic performances. The objective of this thesis is the modeling of layered sheet steel elements, to accurately predict dynamic performance. During the development of the layered sheet steel model, the numerical modeling approach, the Finite Element Analysis and the Experimental Modal Analysis are applied in building a modal model of the layered sheet steel elements. Furthermore, in view of getting a better understanding of the dynamic behavior of layered sheet steel, several binding methods have been studied to understand and demonstrate how a binding method affects the dynamic behavior of layered sheet steel elements when compared to single homogeneous steel plate. Based on the developed layered sheet steel model, the dynamic behavior of a lightweight wheel structure to be used as the structure for the stator of an outer rotor Direct-Drive Permanent Magnet Synchronous Generator designed for high-power wind turbines is studied.

Novel virtual environment and real-time simulation based methods for improving life-cycle efficiency of non-road mobile machinery

Virtual environments and real-time simulators (VERS) are becoming more and more important tools in research and development (R&D) process of non-road mobile machinery (NRMM). The virtual prototyping techniques enable faster and more cost-efficient development of machines compared to use of real life prototypes. High energy efficiency has become an important topic in the world of NRMM because of environmental and economic demands. The objective of this thesis is to develop VERS based methods for research and development of NRMM. A process using VERS for assessing effects of human operators on the life-cycle efficiency of NRMM was developed. Human in the loop simulations are ran using an underground mining loader to study the developed process. The simulations were ran in the virtual environment of the Laboratory of Intelligent Machines of Lappeenranta University of Technology. A physically adequate real-time simulation model of NRMM was shown to be reliable and cost effective in testing of hardware components by the means of hardware-in-the-loop (HIL) simulations. A control interface connecting integrated electro-hydraulic energy converter (IEHEC) with virtual simulation model of log crane was developed. IEHEC consists of a hydraulic pump-motor and an integrated electrical permanent magnet synchronous motorgenerator. The results show that state of the art real-time NRMM simulators are capable to solve factors related to energy consumption and productivity of the NRMM. A significant variation between the test drivers is found. The results show that VERS can be used for assessing human effects on the life-cycle efficiency of NRMM. HIL simulation responses compared to that achieved with conventional simulation method demonstrate the advances and drawbacks of various possible interfaces between the simulator and hardware part of the system under study. Novel ideas for arranging the interface are successfully tested and compared with the more traditional one. The proposed process for assessing the effects of operators on the life-cycle efficiency will be applied for wider group of operators in the future. Driving styles of the operators can be analysed statistically from sufficient large result data. The statistical analysis can find the most life-cycle efficient driving style for the specific environment and machinery. The proposed control interface for HIL simulation need to be further studied. The robustness and the adaptation of the interface in different situations must be verified. The future work will also include studying the suitability of the IEHEC for different working machines using the proposed HIL simulation method.

On the Analysis and Control of a Linear Synchronous Servomotor with a Flexible Load

Industry's growing need for higher productivity is placing new demands on mechanisms connected with electrical motors, because these can easily lead to vibration problems due to fast dynamics. Furthermore, the nonlinear effects caused by a motor frequently reduce servo stability, which diminishes the controller's ability to predict and maintain speed. Hence, the flexibility of a mechanism and its control has become an important area of research. The basic approach in control system engineering is to assume that the mechanism connected to a motor is rigid, so that vibrations in the tool mechanism, reel, gripper or any apparatus connected to the motor are not taken into account. This might reduce the ability of the machine system to carry out its assignment and shorten the lifetime of the equipment. Nonetheless, it is usually more important to know how the mechanism, or in other words the load on the motor, behaves. A nonlinear load control method for a permanent magnet linear synchronous motor is developed and implemented in the thesis. The purpose of the controller is to track a flexible load to the desired velocity reference as fast as possible and without awkward oscillations. The control method is based on an adaptive backstepping algorithm with its stability ensured by the Lyapunov stability theorem. As a reference controller for the backstepping method, a hybrid neural controller is introduced in which the linear motor itself is controlled by a conventional PI velocity controller and the vibration of the associated flexible mechanism is suppressed from an outer control loop using a compensation signal from a multilayer perceptron network. To avoid the local minimum problem entailed in neural networks, the initial weights are searched for offline by means of a differential evolution algorithm. The states of a mechanical system for controllers are estimated using the Kalman filter. The theoretical results obtained from the control design are validated with the lumped mass model for a mechanism. Generalization of the mechanism allows the methods derived here to be widely implemented in machine automation. The control algorithms are first designed in a specially introduced nonlinear simulation model and then implemented in the physical linear motor using a DSP (Digital Signal Processor) application. The measurements prove that both controllers are capable of suppressing vibration, but that the backstepping method is superior to others due to its accuracy of response and stability properties.

Sähkökoneen staattorikäämityksen kehittäminen

Tämä insinöörityö tehtiin ABB:n Pitäjänmäen konetehtaalle Tahtikoneet-tulosyksikölle. Työssä tutkittiin mahdollisuuksia valmistaa murtovakovyyhtejä kestomagneettituuligeneraattoreihin, joissa vakoluku on alle yhden. Työ tehtiin tutustumalla aluksi Pitäjänmäen konetehtaan käytössä oleviin vyyhden valmistus- ja käämintämenetelmiin. Lisäksi tutkittiin erilaisia mahdollisia murtovakovyyhden valmistusmenetelmiä, joista lupaavimpia myös kokeiltiin. Saatujen kokemusten pohjalta valittiin vyyhden valmistusmenetelmä, jonka mukaan valmistettiin koe-erä. Koe-erälle suoritettiin mittauksia, joilla varmistettiin niiden sähköinen kestävyys Työn tuloksena valitulla valmistusmenetelmällä valmistettiin vyyhdet prototyyppi tuuligeneraattorin.

Sähköisen lineaariservomoottorijärjestelmän dynamiikan simulointi

Työssä johdettiin sähköisen lineaariservomoottorijärjestelmän dynaaminen malli. Lineaarimoottori on keksintönä vanha, mutta vasta viimeaikoina kestomagneettimateriaalien kehittyessä ja halvetessa lineaarimoottorista on tullut varteenotettava vaihtoehto pyörivän moottorin ja lineaarisen liikkeen toteuttavan mekanismin yhdistelmälle. Kestomagnetoituja lineaarimoottoreita käytetään sovelluksissa, joissa tarvitaan tarkkaa paikoitusta ja nopeudella ja kiihtyvyydellä on suuret vaatimukset. Moottorimalli toteutettiin vuorovaikutteisena simulointimallina. Moottorimalli, josta saatiin moottorin voima, rakennettiin MatLabâ 6.0/Simulinkâ –ohjelmalle ja moottoriin kiinnitetyn mekaniikan malli ADAMS 10.0 –ohjelmalle. Mallit on liitetty tämän jälkeen vuorovaikutteiseksi simulointimalliksi. Simuloinnista saatuja tuloksia on verrattu koneautomaation laboratorioon hankitun lineaarimoottorijärjestelmän mitattuihin vasteisiin.

Eddy-current losses in rotor surface mounted permanent magnets

The aim of the work is to study the existing analytical calculation procedures found in literature to calculate the eddy-current losses in surface mounted permanent magnets within PMSM application. The most promising algorithms are implemented with MATLAB software under the dimensional data of LUT prototype machine. In addition finite elements analyze, utilized with help of Flux 2D software from Cedrat Ltd, is applied to calculate the eddy-current losses in permanent magnets. The results obtained from analytical methods are compared with numerical results.

Kestomagneettiavusteisen synkronireluktanssikoneen soveltuvuus autokäyttöihin

Työn tavoitteena on tehdä kirjallisuuskatsaus kestomagneettiavusteisesta synkronireluktanssikoneesta ja tarkastella sen soveltuvuutta sähköauton voimantuottoon. Lisäksi työssä tehdään katsaus tämänhetkisiin sähköautoihin ja niissä esiintyviin koneratkaisuihin ja esitetään esimerkkilaskelma moottorin voimantarpeesta auton eri toiminta-alueilla. Tarkasteluissa selvisi, että kestomagneettiavusteinen synkronireluktanssikone on varteenotettava moottoriratkaisu sähköautoissa. Tämänhetkisissä sähköautoissa pääosin esiintyviin epätahtikoneeseen ja kestomagneettitahtikoneeseen verrattuna kestomagneettiavusteisella synkronireluktanssikoneella on muutamia ominaisuuksia, jotka autokäytössä ovat erityisesti sen vahvuuksia. Epätahtikoneeseen verrattuna kestomagneettiavusteisella synkronireluktanssikoneella on etuina huomattavasti pienempi paino ja synkronisuus ja kestomagneettitahtikoneeseen verrattuna sillä on paremmat kentänheikennysominaisuudet ja näin laajempi nopeusalue käytettävissä.

Hysteresis Losses in Sintered NdFeB Permanent Magnets in Rotating Electrical Machines

Permanent magnet materials are nowadays widely used in the electrical machine manufacturing industry. Eddy current loss models of permanent magnets used in electrical machines are frequently discussed in research papers. In magnetic steel materials we have, in addition to eddy current losses, hysteresis losses when AC or a rotating flux travels through the material. Should a similar phenomenon also be taken into account in calculating the losses of permanent magnets? Actually, every now and then authors seem to assume that some significant hysteresis losses are present in rotating machine PMs. This paper studies the mechanisms of possible hysteresis losses in PMs and their role in PMs when used in rotating electrical machines.

Designing Digital Filters for Servo Systems

The aim of this work was to select an appropriate digital filter for a servo application and to filter the noise from the measurement devices. Low pass filter attenuates the high frequency noise beyond the specified cut-off frequency. Digital lowpass filters in both IIR and FIR responses were designed and experimentally compared to understand their characteristics from the corresponding step responses of the system. Kaiser Windowing and Equiripple methods were selected for FIR response, whereas Butterworth, Chebyshev, InverseChebyshev and Elliptic methods were designed for IIR case. Limitations in digital filter design for a servo system were analysed. Especially the dynamic influences of each designed filter on the control stabilityof the electrical servo drive were observed. The criterion for the selection ofparameters in designing digital filters for servo systems was studied. Control system dynamics was given significant importance and the use of FIR and IIR responses in different situations were compared to justify the selection of suitableresponse in each case. The software used in the filter design was MatLab/Simulink® and dSPACE's DSP application. A speed controlled Permanent Magnet Linear synchronous Motor was used in the experimental work.

Position sensorless electrically excited synchronous motor drive for industrial use based on direct flux linkage and torque control

Synchronous machines with an AC converter are used mainly in large drives, for example in ship propulsion drives as well as in rolling mill drives in steel industry. These motors are used because of their high efficiency, high overload capacity and good performance in the field weakening area. Present day drives for electrically excited synchronous motors are equipped with position sensors. Most drives for electrically excited synchronous motors will be equipped with position sensors also in future. This kind of drives with good dynamics are mainly used in metal industry. Drives without a position sensor can be used e.g. in ship propulsion and in large pump and blower drives. Nowadays, these drives are equipped with a position sensor, too. The tendency is to avoid a position sensor if possible, since a sensor reduces the reliability of the drive and increases costs (latter is not very significant for large drives). A new control technique for a synchronous motor drive is a combination of the Direct Flux Linkage Control (DFLC) based on a voltage model and a supervising method (e.g. current model). This combination is called Direct Torque Control method (DTC). In the case of the position sensorless drive, the DTC can be implemented by using other supervising methods that keep the stator flux linkage origin centered. In this thesis, a method for the observation of the drift of the real stator flux linkage in the DTC drive is introduced. It is also shown how this method can be used as a supervising method that keeps the stator flux linkage origin centered in the case of the DTC. In the position sensorless case, a synchronous motor can be started up with the DTC control, when a method for the determination of the initial rotor position presented in this thesis is used. The load characteristics of such a drive are not very good at low rotational speeds. Furthermore, continuous operation at a zero speed and at a low rotational speed is not possible, which is partly due to the problems related to the flux linkage estimate. For operation in a low speed area, a stator current control method based on the DFLC modulator (DMCQ is presented. With the DMCC, it is possible to start up and operate a synchronous motor at a zero speed and at low rotational speeds in general. The DMCC is necessary in situations where high torque (e.g. nominal torque) is required at the starting moment, or if the motor runs several seconds at a zero speed or at a low speed range (up to 2 Hz). The behaviour of the described methods is shown with test results. The test results are presented for the direct flux linkage and torque controlled test drive system with a 14.5 kVA, four pole salient pole synchronous motor with a damper winding and electric excitation. The static accuracy of the drive is verified by measuring the torque in a static load operation, and the dynamics of the drive is proven in load transient tests. The performance of the drive concept presented in this work is sufficient e.g. for ship propulsion and for large pump drives. Furthermore, the developed methods are almost independent of the machine parameters.

Kestomagneettikoneen roottorin väsymisanalyysi

Työn tavoitteena oli luoda työkalu kestomagneettikoneiden roottoreiden väsymisen analysointia varten. Työkalu toteutettiin siten, että siihen voidaan liittää oikeasta koneesta mitattu kuormitusdata, sekä tarvittavat materiaalitiedot. Kuormitusdata muunnetaan työkalussa jännityshistoriaksi käyttämällä elementtimenetelmän avulla laskettavaa skaalauskerrointa. Kestoiän laskemiseen analyysityökalu käyttää jännitykseen perustuvaa menetelmää sekä rainflowmenetelmää ja Palmgren-Minerin kumulatiivista vauriosääntöä. Lisäksi työkalu tekee tutkittavalle tapaukselle Smithin väsymislujuuspiirroksen. Edellä mainittujen menetelmien lisäksi työn teoriaosassa esiteltiin väsymisanalyysimenetelmistä myös paikalliseen venymään perustuva menetelmä sekä murtumismekaniikka. Nämä menetelmät jäivät monimutkaisuutensa vuoksi toteuttamatta työkalussa. Väsymisanalyysityökalulla laskettiin kestoiät kahdelle esimerkkitapaukselle. Kummassakin tapauksessa saatiin tulokseksi ääretön kestoikä, mutta aksiaalivuokoneen roottorin dynaaminen varmuus oli pieni. Vaikka tulokset vaikuttavat järkeviltä, ne olisi vielä hyvä verifioida esimerkiksi kaupallisen ohjelmiston avulla täyden varmuuden saamiseksi.

Virtual technology and haptic interface solutions for design and control of mobile working machines

Commercially available haptic interfaces are usable for many purposes. However, as generic devices they are not the most suitable for the control of heavy duty mobile working machines like mining machines, container handling equipment and excavators. Alternative mechanical constructions for a haptic controller are presented and analysed. A virtual reality environment (VRE) was built to test the proposed haptic controller mechanisms. Verification of an electric motor emulating a hydraulic pump in the electro-hydraulic system of a mobile working machine is carried out. A real-time simulator using multi-body-dynamics based software with hardware-in-loop (HIL) setup was used for the tests. Recommendations for further development of a haptic controller and emulator electric motor are given.

Kestomagnetoidun roottorin mekaniikkasuunnittelu ja -analysointi

Työssä kehitettiin suurnopeuskäyttöön soveltuva kestomagnetoitu roottori olemassa olevan induktiokoneen staattorirunkoon. Kehitystyön tarkoituksena oli selvittää roottorin mekaaniset raja-arvot, kuten maksimi kehänopeus. Samalla otettiin kantaa myös tarvittaviin analysointi- ja mitoitusmenetelmiin. Maksimi kehänopeuden, laakeroinnin ja roottorin skaalattavuuden selvittäminen edellytti myös tarkkaa materiaaliselvitystä ja optimointia. Tästä syystä työn aikana tehtiin tiivistä yhteistyötä materiaalitoimittajien kanssa. Työn tuloksena syntyi uusi menetelmä toteuttaa radiaalisen magneettivuon luova kestomagneettiroottori 200 m/s kehänopeudelle. Suunniteltua roottoriratkaisua käytetään testausroottorina, jolla selvitetään valmistuksen, kokoonpanon ja sähkötehon rajoitteet käytännössä. Suunnittelutyö edellyttikin jatkuvaa iterointia sähkösuunnittelun ja roottorin osien valmistajien kanssa, jotta löydettiin paras kompromissiratkaisu roottorin prototyyppiin. Tämän seurauksena saatiin luotua varsin tarkat suunnittelu- ja analysointiraja-arvot kestomagneettiroottorin tuotteistettavia versioita varten.