Quantitative elemental analysis of dry-ashed bark and wood samples of birch, spruce and pine from south-western Finland using PIXE

A total of over 200 different samples of bark and wood of Silver birch, Norway spruce and Scots pine were analysed. Samples were taken from several areas in western Finland, some with known sources of atmospheric heavy metal emission (Harjavalta, Ykspihlaja). Also analytical data for pine needles from some sites are reported. The chemical analyses were performed by thick-target particle-induced X-ray emission (PIXE) spectrometry after preconcentration by dry ashing of samples at 550oC. The following elements were quantified in most of the samples: P, S, K, Ca, Mn, Fe, Ni, Cu, Zn, Rb, Sr, Cd, Ba and Pb. The ash percentage and the chemical composition of ashes of different wood materials were also obtained, as dry ashing was used in the analytical procedure. The variations in elemental concentrations in wood and bark of an individual tree, expressed as RSDs, were mostly in the range 10 – 20 %. For several trees of the same species sampled from small areas (< 1 ha), the variations in elemental concentrations were surprisingly high (RSDs 20 – 50 %). In the vicinity of metal plants, effects of strong atmospheric heavy metal pollution (pollution factor above 100) were observed in pine bark. The increase of heavy metal content in wood samples from the same sites was quite small. Elemental concentrations in ashes of bark and wood, from areas with no local source of atmospheric pollution, were relatively uniform. Based on this observation an alternative way of demonstrating atmospheric pollution of tree bark is discussed.

Polttoainekoostumuksen vaikutus lentotuhkan laatuun ja hyötykäyttömahdollisuuksiin UPM-Kymmene Oyj:n Kaukaan tehtailla

Tavoitteena tässä diplomityössä oli selvittää UPM-Kymmene Oyj:n Kaukaan tehtaiden lentotuhkan hyötykäyttömahdollisuuksia. Tarkastelussa olivat mukana metsälannoite-, maarakennus- sekä sementtiteollisuuskäytöt. Ensin työssä tarkasteltiin näitä vaihtoehtoja kirjallisuuden perusteella. Tämän jälkeen pohdittiin Kaukaan lentotuhkasta tehtyjen analyysien perusteella, mihin käyttökohteisiin lentotuhka soveltuu tällä hetkellä, sekä tulevaisuudessa uuden biopolttoainekattilan myötä. Lentotuhkan hyötykäyttöä lannoitteena ja maarakentamisessa säätelee lainsäädäntö. Lannoitteille on asetuksessa säädetty tietyille haitta-aineille enimmäispitoisuudet, jotka tuhkan tulee alittaa, jotta sitä voitaisiin hyödyntää. Maarakennuskäytölle on asetuksessa määritelty raja-arvot, jotka alitettaessa voidaan tuhkaa hyödyntää rakenteissa ilmoitusmenettelyllä. Tämä menettely helpottaa rakennusprojekteja huomattavan paljon, sillä tällöin ympäristölupaa ei tarvitse hakea jokaiselle projektille erikseen. Maarakennuskäyttö on mahdollista, vaikkei raja-arvoja alitettaisikaan, mutta tällöin ympäristöluvan hakeminen hankaloittaa projektien etenemistä ja aiheuttaa kustannuksia. Tuhkan on lisäksi oltava ominaisuuksiltaan riittävän hyvää, jotta hyötykäyttö olisi mahdollista. Kaukaan tuhkasta tehtyjen analyysien perusteella huomattiin, että se sopii hyvin metsälannoitteeksi ja todennäköisesti myös sementtiteollisuuskäyttöön. Maarakennuskäytön osalta tulokset osoittivat tuhkan olevan juuri rajoilla ilmoitusmenettelyn hyödyntämisen suhteen. Maarakennuskäytöstä tarvitaankin vielä lisäselvityksiä jatkossa. Uudessa polttolaitoksessa poltetaan myös turvetta puuperäisen lisäksi. Kirjallisuuden perusteella voitiin tehdä arvio, mihin suuntaan turve tulee tuhkaa todennäköisesti muuttamaan. Todettiin, että turpeen poltto parantaa todennäköisesti tuhkan laatua sementtiteollisuudessa käytön kannalta. Tuhkan lannoitekäyttöön turpeen poltolla todettiin taas olevan negatiivisia vaikutuksia. Maarakennuskäytön kannalta turpeella saattaa myös olla negatiivisia vaikutuksia. Tuhkaa kannattaisikin käyttää sementtiteollisuudessa silloin kun turvetta on polttoaineessa paljon ja muuhun käyttöön silloin kun turvetta on vähän.

Non-wood massojen vedenpoiston arvioiminen märkäpuristuksessa

Yksivuotisten kasvien (non-wood) kuitua verrataan usein lehtipuukuituihin. Käytetyimpiä non-wood kasveja ovat vehnän olki, bambu, järviruoko ja bagassi. Non-wood massan erottaa puumassasta kuitenkin korkea silikaattipitoisuus sekä parenkyymisolupitoisuus, joka antaa massalle korkean hienoainepitoisuuden. Tämä yhdessä korkean hemiselluloosapitoisuuden ja lyhyen kuidun pituuden kanssa heikentävät voimakkaasti non-wood massan vedenpoisto-ominaisuuksia. Non-wood kuidulla voidaan korvata lehtipuumassaa hienopapereissa. Non-wood kuitu antaa paperille hyvän opasiteetin, korkean valonsirontakertoimen sekä sileän painopinnan. Massaan lisättävä pitkäkuituinen havupuumassa parantaa ajetta¬vuutta paperikoneella ja helpottaa massan vedenpoistoa. Non-wood massan vedenpoistoa voidaan tehostaa esimerkiksi poistamalla osa hienoaineesta, käyttämällä non-wood massalle sopivaa keittotapaa sekä käyttämällä märkä¬puristuksessa pitkänippityyppistä puristinratkaisua. Myös non-wood kuidun kuivaaminen parantaa vedenpoistoa. Tässä tutkimuksessa kirjallisuusosassa keskityttiin yleisimpiin paperin valmistuksessa käytettäviin non-wood kuidun lähteisiin, märkäpuristuksen teoriaan ja tapoihin tehostaa vedenpoistoa. Kokeellisessa osassa tutkittiin vehnänolkimassan käyttäytymistä märkäpuristuksessa erilaisten ominaisuuksien pohjalta. Tutkimuksen kohteena oli non-wood massan keittotapa (hapan/alkali), hienoainepitoisuus, silikaattipitoisuus sekä kuivattu/kuivaamaton kuitu. Vertailun vuoksi tutkimuksessa oli mukana myös yksi järviruokomassa. Tuloksista huomataan, että non-wood massan vedenpoistoon vaikuttaa hienoainepitoisuus, kuidun kuivaus sekä massan valmistustapa. Järviruokomassan veden¬poisto on tehokkaampaa kuin vehnänolkimassan paremman kuitu¬koostumuksensa takia. Jos hienopaperimassassa korvataan lehtipuumassaa non-wood kuidulla maksimissaan 40 %, massan vedenpoistoa voidaan hyvin arvioida erilaisten suotautuvuusmittojen, kuten freeneksen, vedenpidätyskyvyn ja suotautumisajan, avulla.

Fractionation of wood hydrolysate by ultrafiltration membranes at high temperature

Ultrafiltration (UF) is already used in pulp and paper industry and its demand is growing because of the required reduction of raw water intake and the separation of useful compounds from process waters. In the pulp and paper industry membranes might be exposed to extreme conditions and, therefore, it is important that the membrane can withstand them. In this study, extractives, hemicelluloses and lignin type compounds were separated from wood hydrolysate in order to be able to utilise the hemicelluloses in the production of biofuel. The performance of different polymeric membranes at different temperatures was studied. Samples were analysed for total organic compounds (TOC), lignin compounds (UV absorption at 280 nm) and sugar. Turbidity, conductivity and pH were also measured. The degree of fouling of the membranes was monitored by measuring the pure water flux before and comparing it with the pure water flux after the filtration of hydrolysate. According to the results, the retention of turbidity was observed to be higher at lower temperature compared to when the filtrations were operated at high temperature (70 °C). Permeate flux increased with elevated process temperature. There was no detrimental effect of temperature on most of the membranes used. Microdyn-Nadir regenerated cellulose membranes (RC) and GE-Osmonics thin film membranes seemed to be applicable in the chosen process conditions. The Polyethersulphone (NF-PES-10 and UH004P) and polysulphone (MPS-36) membranes used were highly fouled, but they showed high retentions for different compounds.

Recovery of Hemicelluloses from Wood Hydrolysates by Membrane Filtration

Hemicelluloses are among the most important natural resources that contain polysaccharides. In this study the separation and purification of hemicelluloses from water extraction liquors containing wood hemicelluloses, lignin compounds and monosaccharide by using membrane filtration was investigated. The isolation of the hemicelluloses from the wood hydrolysates was performed in two steps: concentration of high molar mass hemicelluloses by ultrafiltration and separation of low molar mass hemicelluloses from monomeric sugars using tight ultrafiltration membranes. The purification of the retained hemicelluloses was performed by diafiltration. During the filtration experiments, the permeate flux through ultrafiltration and tight ultrafiltration membranes was relatively high. The fouling ability of the used membranes was relatively low. In our experiments, the retention of hemicelluloses using two filtration steps was almost complete. The separation of monosaccharides from hemicelluloses was relatively high and the purification of hemicelluloses by diafiltration was highly efficient. The separation of lignin from hemicelluloses was partially achieved. Diafiltration showed potential to purify retained hemicelluloses from lignin and other organics. The best separation of lignin from hemicelluloses in the first filtration step was obtained using the UC005 membrane. The GE-5 and ETNA01PP membranes showed potential to purify and separate lignin from hemicelluloses. However, the feed solution of the second filtration stages (from different ultrafiltration membranes) affected the permeate flux and the separation of various extracted compounds from hemicelluloses. The GE-5 and ETNA01PP membranes gave the efficient purification of the hemicelluloses when using diafiltration. Separation of degraded xylan from glucomannan (primary spruce hemicelluloses) was also possible using membrane filtration. The best separation was achieved using the GE-5 membrane. The retention of glucomannan was three times higher than xylan retention.

Fractionation of Wood Extracts

The aim of this thesis was to fractionate wood extracts into pure fractions using membrane technology, to observe membrane behaviour in solvents and to study the effect of conditioning on membrane performance. Four different wood extracts were used in the performed filtrations. In the literature part, the focus was on the effect of different solvent properties on polymeric membranes, especially on their retention and flux. Solute properties, such as shape, polarity and charge, were examined. Transport models, membrane stability and ways to improve the stability, when solvents were filtered, were also discussed. The experimental part consisted of a series of filtrations, where the effect of the wood extracts and solvent concentration on solute retention was observed. Polymeric and ceramic membranes were tested under different conditions and the solute analyses were performed with GC and GC-MS. It was discovered that it is possible to fractionate wood extracts using membrane technology to some extent, but more research must be done to understand the mechanisms behind the various interactions between the solvent and the membrane. Conditioning was also considered as an important part of the membrane pre-treatment.

The Innovation Process – Aiming towards Innovativeness in a Construction Company

The bachelor’s thesis concentrates on the innovativeness in the construction industry. The purpose of the thesis is to define the innovation as a concept reflected on a context of the construction industry. The second objective is to examine how the construction companies could foster and increase the innovativeness. The third objective was to find out tools, methods and phases of the front-end of the innovation process. The construction industry is often considered as a traditional and an old-fashioned manufacturing industry. The innovation or the innovativeness rarely linked to the construction industry. Productivity is a common problem in the construction industry. The construction industry needs to increase the productivity to compete in a globalized world. The productivity can be increased by the innovation. The thesis based on a literature review. The findings from the literature include a description of the innovation as a concept, the innovative culture and the innovation process as a context of the construction industry. The phases of the front-end of the innovation process were explained. Customers centered approach was taken into account in the innovation process. The required tools and methods for managing the front-end of the innovation process were illustrated. The thesis ensures the importance of the innovation facing challenges of the construction industry. Managing the front-end of the innovation is the most important aspect to stand out from the less innovative companies. To take a full advantage of the innovation companies cannot fear of changes. The innovation process requires a full support of the top management of the company. Taking into consideration a theoretical aspect of the thesis a further research is required to respond practical needs of the company. Tools and methods should be considered according the company’s needs and activities. Company’s existing state and culture should be examined before implementing the front-end of the innovation process to ensure the functionality.

Research of wood fuel market in Ukraine and the Republic of Belarus

The goal of the present work was to describe the wood fuel market of Ukraine and the Republic of Belarus, to estimate wood fuel potential and to research opportunities of wood fuel trading. Nowadays the wood waste, wood residues and by-products are becoming more and more potential raw materials for energy production. Against the background of unstable prices of traditional energy sources and environmental degradation, European States are planning to get 12% of energy from alternative sources already in 2010. Wastes of wood-working and agricultural productions are such sources. At present time the most popular wood biofuels are wood pellets, briquettes, wood chips and logs. Ukraine and the Republic of Belarus have a rather big potential of wood fuel resources. But wood fuels markets of these countries are on the entry level and quite disorganized. There is almost no domestic usage of wood biofuel. All produced pellets, briquettes as well as wood chips and logs go to the export, but the volumes are not high at present time. Ukraine and the Republic of Belarus have a very suitable geographical location. The most promising directions of wood fuel trading are developed wood fuel markets of Northern countries, Austria, Germany as well as actively developing markets of Poland and Hungary. At the long distance truck and sea transportation are the most appropriate. At a short distance cheap transportation by rail is more suitable. Thereby export is a potential opportunity for development of wood fuel production and in the future for usage in the researched countries.

Research of wood fuel market in North-West of Russia

The main purposes of this study are analyzing of forest sector of North-West and research of potentials of wood fuel market in this region. Research is focused on definition of the most perspective areas for export of wood fuel: logging residues, industrial wood processing residues, pellets and briquettes. Russian wood energy industry is very young in comparison with European countries. Nowadays there are no support and serious attention from the government to this sector. Hence almost all wood fuel market is oriented to the Western Europe. Export of wood fuel is dominated over the internal consumption. Pellet production in North –West is rapidly growing. Despite internal market has been developed the lion's share of pellets goes to export. Part of industrial wood processing residues is used by producers for their own goals, part goes to the export and rest of them is not used at all. Logging residues as raw materials for fuel have great potentials; most of them are left in a forest. Special techniques for their processing are too expensive for Russian entrepreneur. Some parts of North –West, which are situated close to the border with European countries, are potential for export. Political, economical and logistical challenges are complicated facilities for foreign customer to purchase wood fuel in remote parts of North-West. However some decisions for solving this problem exist and Russian manufactures are still interested in export of their products.