High-Speed Solid-Rotor Induction Machine – Electromagnetic Calculation and Design

Within the latest decade high-speed motor technology has been increasingly commonly applied within the range of medium and large power. More particularly, applications like such involved with gas movement and compression seem to be the most important area in which high-speed machines are used. In manufacturing the induction motor rotor core of one single piece of steel it is possible to achieve an extremely rigid rotor construction for the high-speed motor. In a mechanical sense, the solid rotor may be the best possible rotor construction. Unfortunately, the electromagnetic properties of a solid rotor are poorer than the properties of the traditional laminated rotor of an induction motor. This thesis analyses methods for improving the electromagnetic properties of a solid-rotor induction machine. The slip of the solid rotor is reduced notably if the solid rotor is axially slitted. The slitting patterns of the solid rotor are examined. It is shown how the slitting parameters affect the produced torque. Methods for decreasing the harmonic eddy currents on the surface of the rotor are also examined. The motivation for this is to improve the efficiency of the motor to reach the efficiency standard of a laminated rotor induction motor. To carry out these research tasks the finite element analysis is used. An analytical calculation of solid rotors based on the multi-layer transfer-matrix method is developed especially for the calculation of axially slitted solid rotors equipped with wellconducting end rings. The calculation results are verified by using the finite element analysis and laboratory measurements. The prototype motors of 250 – 300 kW and 140 Hz were tested to verify the results. Utilization factor data are given for several other prototypes the largest of which delivers 1000 kW at 12000 min-1.

Jännitteen reunan hallinta taajuusmuuttajissa

Diplomityössä perehdyttiin taajuusmuuttajien toimintaan ja ohjaukseen. Lisäksi työssä tarkasteltiin vaihtosuuntaajan nopeiden transienttitilojen aiheuttamaa moottorin ylijännitettä. Moottorikaapelin heijastuksia käsiteltiin vertaamalla moottorikaapelia siirtolinjaan ja todennettiin ylijännitteen syyt. Ylijännitteen vähentämiseksi on kehitetty useita suodatusmenetelmiä. Työssä vertailtiin näitä menetelmiä ja kartoitettiin kaupallisia vaihtoehtoja. Taajuusmuuttajan ohjaus on tähän päivään asti tehty yleensä käyttäen mikroprosessoria sekä logiikkapiiriä. Tulevaisuudessa ohjaukseen käytetään todennäköisesti uudelleenohjelmoitavia FPGA-piirejä (Field Programmable Gate Array). FPGA-piirin etuihin kuuluu uudelleenohjelmoitavuus sekä ohjauksen keskittäminen yhdelle piirille.

Test automation of digital mammography device

Testing of a complex software is time consuming. Automated tools are available quite a lot for desktop applications, but for embedded systems a custom-made tool is required Building a complete test framework is a complicated task. Therefore, the test platform was built on top of an already existing tool, CANoe. CANoe is a tool for CAN bus analysis and node simulation. The functionality of CANoe was extended with LabVIEW DLL. The LabVIEW software was used for simulating hardware components of the embedded device As a result of the study, a platform was created where tests could be automated. Of the current test plan, 10 percent were automated and up to 60 percent could be automated with the current functionality.

Design of flywheel generator for a diesel hybrid working machine

The aim of this work is to design a flywheel generator for a diesel hybrid working machine. In this work we perform detailed design of a generator. Mobile machines are commonly used in industry: road building machines, three harvesting machines, boring machines, trucks and other equipment. These machines work with a hydraulic drive system. This system provides good service property and high technical level. Manufacturers of mobile machines tend to satisfy all requirements of customers and modernized drive system. In this work also a description of the frequency inverter is present. Power electronics system is one of the basic parts for structures perform in the project.

Customer driven business model – connecting customer value to firm resources in ICT value networks

The objective of this thesis is to provide a business model framework that connects customer value to firm resources and explains the change logic of the business model. Strategic supply management and especially dynamic value network management as its scope, the dissertation is based on basic economic theories, transaction cost economics and the resource-based view. The main research question is how the changing customer values should be taken into account when planning business in a networked environment. The main question is divided into questions that form the basic research problems for the separate case studies presented in the five Publications. This research adopts the case study strategy, and the constructive research approach within it. The material consists of data from several Delphi panels and expert workshops, software pilot documents, company financial statements and information on investor relations on the companies’ web sites. The cases used in this study are a mobile multi-player game value network, smart phone and “Skype mobile” services, the business models of AOL, eBay, Google, Amazon and a telecom operator, a virtual city portal business system and a multi-play offering. The main contribution of this dissertation is bridging the gap between firm resources and customer value. This has been done by theorizing the business model concept and connecting it to both the resource-based view and customer value. This thesis contributes to the resource-based view, which deals with customer value and firm resources needed to deliver the value but has a gap in explaining how the customer value changes should be connected to the changes in key resources. This dissertation also provides tools and processes for analyzing the customer value preferences of ICT services, constructing and analyzing business models and business concept innovation and conducting resource analysis.

Organizing automation maintenance business in Russia

The target of this thesis is to find out potential of automation maintenance services in Russian industry, especially in the region of St. Petersburg. At the beginning of this study the industrial maintainability and process efficiency are discussed from the point of view of process automation. A survey of the present technology and maintenance methods has been made during five visits to local plants. The results of the interviews are analyzed numerically to clarify the common needs and the potential of automation maintenance services. The most interesting services are evaluated by their required resources to find economically justified solutions for the needs of the industry. As results of this study, some service products that would interest interviewed companies have been introduced. These could be offered to the industry to enhance cost-efficiency and productivity of processes.

Eristekourujen ponttauslaitteen suunnittelu

Diplomityössä suunnitellaan eristekourujen ponttauslaite, jolla pystytään ponttaamaan eristekouruja. Pontattavien eristekourujen pituus ja halkaisija muuttuvat. Suunnittelun lähtökohtana on nykyisin käytössä olevien ponttauslaitteiden ergonomia- ja työturvallisuusongelmat. Työssä käydään läpi erilaisia mahdollisuuksia ponttauslaitteen toteutukseen ja kehitellään kaksi periaatteellista ratkaisua toimiviksi kokoonpanoiksi. Kokoonpanoista valitaan perustellusti parempi vaihtoehto jatkokehitykseen ja se kehitellään valmiiksi ponttauslaitteeksi. Työ käsittää laitteen mekaniikkasuunnittelun, automaatiosuunnittelu rajataan työn ulkopuolelle. Työn eteneminen seuraa järjestelmällisen koneensuunnitteluprosessin vaiheita. Lopputuloksena suunniteltiin laite, joka toteuttaa sille asetetut suoritusvaatimukset. Suunniteltu laite on turvallinen ja ergonomiset vaatimukset täyttävä. Lisäksi laitteen rungolle tehtiin värähtelytarkasteluja, joiden perusteella analysoitiin ominais- ja herätetaajuuksien suhteita sekä rungon jäykistämisen vaikutuksia.

Rouhintasorvauksen säätöjärjestelmä

Tässä työssä kuvataan menetelmä, jonka avulla on mahdollista sorvausprosessista mitattujen signaalien perusteella muokata lastuamisprosessin parametreja siten, että prosessissa mahdollisesti esiintyvät ongelmatilanteet korjataan. Työ on tehty osana Feedchip-tutkimushanketta ja tukeutuu tutkimushankkeessa aiemmin tehtyyn työhön vaadittavien korjaustoimenpiteiden, signaaleja mittaavien antureiden instrumentoinnin sekä alustavan ongelmatilanteiden ominaispiirteiden signaaleista tunnistuksen osalta. Tämä työ keskittyy esittelemään toiminnot, joiden avulla aiemmat tulokset voidaan koota yhteen kokonaisuuteen. Järjestelmän toiminta edellyttää sen osien toiminnan korkean tason koordinointia. Lisäksi määritellään päättelyjärjestelmä, joka kykenee mitatuista arvoista tunnistettujen ongelmatilanteiden esiintymisasteiden perusteella määrittämään tarvittavat toimenpiteet ongelmatilanteiden poistamiseksi. Kandidaatintyön rinnalla toteutetaan ohjelmisto Lappeenrannan teknillisen yliopiston konepajatekniikan laboratorion sorvausjärjestelmän yhteyteen rakennetun prototyyppilaitteiston ohjaamiseksi.

Electrical machine in a Hybrid Electrical Vehicle

Hybrid electric vehicles (HEV) have attracted very much attention during the latest years. Increasing environmental concern and an increase in fuel prices are key factors for the growing interest towards the HEV. In a hybrid electric vehicle the power train consists of both a mechanical power system and an electric power transmission system. The major subsystems in the mechanical power system are the internal combustion engine which powers the vehicle; electric power transmission including an energy storage, power electronic inverter, hybrid control system; the electric motor drive that runs either in the generating mode or in the motoring mode to process the power flow between the energy storage and the electrical machine. This research includes two advanced electric motors for a parallel hybrid: induction machine and permanent magnets synchronous machine. In the thesis an induction motor and a permanent magnet motor are compared as propulsion motors. Electric energy storages are also studied.

Salient Pole Synchronous Machine Modelling in an Industrial Direct Torque Controlled Drive Application

Synchronous motors are used mainly in large drives, for example in ship propulsion systems and in steel factories' rolling mills because of their high efficiency, high overload capacity and good performance in the field weakening range. This, however, requires an extremely good torque control system. A fast torque response and a torque accuracy are basic requirements for such a drive. For large power, high dynamic performance drives the commonly known principle of field oriented vector control has been used solely hitherto, but nowadays it is not the only way to implement such a drive. A new control method Direct Torque Control (DTC) has also emerged. The performance of such a high quality torque control as DTC in dynamically demanding industrial applications is mainly based on the accurate estimate of the various flux linkages' space vectors. Nowadays industrial motor control systems are real time applications with restricted calculation capacity. At the same time the control system requires a simple, fast calculable and reasonably accurate motor model. In this work a method to handle these problems in a Direct Torque Controlled (DTC) salient pole synchronous motor drive is proposed. A motor model which combines the induction law based "voltage model" and motor inductance parameters based "current model" is presented. The voltage model operates as a main model and is calculated at a very fast sampling rate (for example 40 kHz). The stator flux linkage calculated via integration from the stator voltages is corrected using the stator flux linkage computed from the current model. The current model acts as a supervisor that prevents only the motor stator flux linkage from drifting erroneous during longer time intervals. At very low speeds the role of the current model is emphasised but, nevertheless, the voltage model always stays the main model. At higher speeds the function of the current model correction is to act as a stabiliser of the control system. The current model contains a set of inductance parameters which must be known. The validation of the current model in steady state is not self evident. It depends on the accuracy of the saturated value of the inductances. Parameter measurement of the motor model where the supply inverter is used as a measurement signal generator is presented. This so called identification run can be performed prior to delivery or during drive commissioning. A derivation method for the inductance models used for the representation of the saturation effects is proposed. The performance of the electrically excited synchronous motor supplied with the DTC inverter is proven with experimental results. It is shown that it is possible to obtain a good static accuracy of the DTC's torque controller for an electrically excited synchronous motor. The dynamic response is fast and a new operation point is achieved without oscillation. The operation is stable throughout the speed range. The modelling of the magnetising inductance saturation is essential and cross saturation has to be considered as well. The effect of cross saturation is very significant. A DTC inverter can be used as a measuring equipment and the parameters needed for the motor model can be defined by the inverter itself. The main advantage is that the parameters defined are measured in similar magnetic operation conditions and no disagreement between the parameters will exist. The inductance models generated are adequate to meet the requirements of dynamically demanding drives.

Integrating distributed generation and Smart Grids into single-family house

This study examines Smart Grids and distributed generation, which is connected to a single-family house. The distributed generation comprises small wind power plant and solar panels. The study is done from the consumer point of view and it is divided into two parts. The first part presents the theoretical part and the second part presents the research part. The theoretical part consists of the definition of distributed generation, wind power, solar energy and Smart Grids. The study examines what the Smart Grids will enable. New technology concerning Smart Grids is also examined. The research part introduces wind and sun conditions from two countries. The countries are Finland and Germany. According to the wind and sun conditions of these two countries, the annual electricity production from wind power plant and solar panels will be calculated. The costs of generating electricity from wind and solar energy are calculated from the results of annual electricity productions. The study will also deal with feed-in tariffs, which are supporting systems for renewable energy resources. It is examined in the study, if it is cost-effective for the consumers to use the produced electricity by themselves or sell it to the grid. Finally, figures for both countries are formed. The figures include the calculated cost of generating electricity from wind power plant and solar panels, retail and wholesale prices and feed-in tariffs. In Finland, it is not cost-effective to sell the produced electricity to the grid, before there are support systems. In Germany, it is cost-effective to sell the produced electricity from solar panels to the grid because of feed-in tariffs. On the other hand, in Germany it is cost-effective to produce electricity from wind to own use because the retail price is higher than the produced electricity from wind.

Performance Evaluation and Calibration of Machine Vision Measurement

This thesis presents the calibration and comparison of two systems, a machine vision system that uses 3 channel RGB images and a line scanning spectral system. Calibration. is the process of checking and adjusting the accuracy of a measuring instrument by comparing it with standards. For the RGB system self-calibrating methods for finding various parameters of the imaging device were developed. Color calibration was done and the colors produced by the system were compared to the known colors values of the target. Software drivers for the Sony Robot were also developed and a mechanical part to connect a camera to the robot was also designed. For the line scanning spectral system, methods for the calibrating the alignment of the system and the measurement of the dimensions of the line scanned by the system were developed. Color calibration of the spectral system is also presented.

Machine Learning and Clinical Text. Supporting Health Information Flow

Fluent health information flow is critical for clinical decision-making. However, a considerable part of this information is free-form text and inabilities to utilize it create risks to patient safety and cost-­effective hospital administration. Methods for automated processing of clinical text are emerging. The aim in this doctoral dissertation is to study machine learning and clinical text in order to support health information flow.First, by analyzing the content of authentic patient records, the aim is to specify clinical needs in order to guide the development of machine learning applications.The contributions are a model of the ideal information flow,a model of the problems and challenges in reality, and a road map for the technology development. Second, by developing applications for practical cases,the aim is to concretize ways to support health information flow. Altogether five machine learning applications for three practical cases are described: The first two applications are binary classification and regression related to the practical case of topic labeling and relevance ranking.The third and fourth application are supervised and unsupervised multi-class classification for the practical case of topic segmentation and labeling.These four applications are tested with Finnish intensive care patient records.The fifth application is multi-label classification for the practical task of diagnosis coding. It is tested with English radiology reports.The performance of all these applications is promising. Third, the aim is to study how the quality of machine learning applications can be reliably evaluated.The associations between performance evaluation measures and methods are addressed,and a new hold-out method is introduced.This method contributes not only to processing time but also to the evaluation diversity and quality. The main conclusion is that developing machine learning applications for text requires interdisciplinary, international collaboration. Practical cases are very different, and hence the development must begin from genuine user needs and domain expertise. The technological expertise must cover linguistics,machine learning, and information systems. Finally, the methods must be evaluated both statistically and through authentic user-feedback.

Concentrated Winding Multiphase Permanent Magnet Machine Design and Electromagnetic Properties – Case Axial Flux Machine

Concentrated winding permanent magnet machines and their electromagnetic properties are studied in this doctoral thesis. The thesis includes a number of main tasks related to the application of permanent magnets in concentrated winding open slot machines. Suitable analytical methods are required for the first design calculations of a new machine. Concentrated winding machines differ from conventional integral slot winding machines in such a way that adapted analytical calculation methods are needed. A simple analytical model for calculating the concentrated winding axial flux machines is provided. The next three main design tasks are discussed in more detail in the thesis. The magnetic length of the rotor surface magnet machines is studied, and it is shown that the traditional methods have to be modified also in this respect. An important topic in this study has been to evaluate and minimize the rotor permanent magnet Joule losses by using segmented magnets in the calculations and experiments. Determination of the magnetizing and leakage inductances for a concentrated winding machine and the torque production capability of concentrated winding machines with different pole pair numbers are studied, and the results are compared with the corresponding properties of integral slot winding machines. The thesis introduces a new practical permanent magnet motor type for industrial use. The special features of the machine are based on the option of using concentrated winding open slot constructions of permanent magnet synchronous machines in the normal speed ranges of industrial motors, for instance up to 3000 min-1, without excessive rotor losses. By applying the analytical equations and methods introduced in the thesis, a 37 kW 2400 min-1 12-slot 10-pole axial flux machine with rotor-surfacemounted magnets is designed. The performance of the designed motor is determined by experimental measurements and finite element calculations.

Computational and Experimental Investigation of the Grooved Roll in Paper Machine Environment

In the paper machine, it is not a desired feature for the boundary layer flows in the fabric and the roll surfaces to travel into the closing nips, creating overpressure. In this thesis, the aerodynamic behavior of the grooved roll and smooth rolls is compared in order to understand the nip flow phenomena, which is the main reason why vacuum and grooved roll constructions are designed. A common method to remove the boundary layer flow from the closing nip is to use the vacuum roll construction. The downside of the use of vacuum rolls is high operational costs due to pressure losses in the vacuum roll shell. The deep grooved roll has the same goal, to create a pressure difference over the paper web and keep the paper attached to the roll or fabric surface in the drying pocket of the paper machine. A literature review revealed that the aerodynamic functionality of the grooved roll is not very well known. In this thesis, the aerodynamic functionality of the grooved roll in interaction with a permeable or impermeable wall is studied by varying the groove properties. Computational fluid dynamics simulations are utilized as the research tool. The simulations have been performed with commercial fluid dynamics software, ANSYS Fluent. Simulation results made with 3- and 2-dimensional fluid dynamics models are compared to laboratory scale measurements. The measurements have been made with a grooved roll simulator designed for the research. The variables in the comparison are the paper or fabric wrap angle, surface velocities, groove geometry and wall permeability. Present-day computational and modeling resources limit grooved roll fluid dynamics simulations in the paper machine scale. Based on the analysis of the aerodynamic functionality of the grooved roll, a grooved roll simulation tool is proposed. The smooth roll simulations show that the closing nip pressure does not depend on the length of boundary layer development. The surface velocity increase affects the pressure distribution in the closing and opening nips. The 3D grooved roll model reveals the aerodynamic functionality of the grooved roll. With the optimal groove size it is possible to avoid closing nip overpressure and keep the web attached to the fabric surface in the area of the wrap angle. The groove flow friction and minor losses play a different role when the wrap angle is changed. The proposed 2D grooved roll simulation tool is able to replicate the grooved aerodynamic behavior with reasonable accuracy. A small wrap angle predicts the pressure distribution correctly with the chosen approach for calculating the groove friction losses. With a large wrap angle, the groove friction loss shows too large pressure gradients, and the way of calculating the air flow friction losses in the groove has to be reconsidered. The aerodynamic functionality of the grooved roll is based on minor and viscous losses in the closing and opening nips as well as in the grooves. The proposed 2D grooved roll model is a simplification in order to reduce computational and modeling efforts. The simulation tool makes it possible to simulate complex paper machine constructions in the paper machine scale. In order to use the grooved roll as a replacement for the vacuum roll, the grooved roll properties have to be considered on the basis of the web handling application.