Vaahdonestokemikaalin syöttötapahtuman tehostamisen vaikutus märkäosan toimintaan

An improved defoamer dosage procedure and a more efficient dosing point to the approach system were studied in this thesis. Their influence on paper machine wet end operations was investigated. The improved defoamer dosing procedure was examined at UMP-Kymmene Tervasaari PM8. Air content and its controlling methods at the paper machine were studied in the literature survey. Also the influence of dissolved gases and entrained air in the papermaking furnish were introduced. Feeding methods – a TrumpJet chemical mixer and traditional feeding devices – were reviewed. The defoamer’s functioning methods were studied. The influence of the use of defoamers was estimated based on the main selected wet end operations. In the experimental part, defoamer mixing with a traditional feeding method and two improved mixing stages were compared based on the air content profiles in PM8’s approach system. The reference dosage procedure was PM8’s old dosing system. The first dosage procedure in the comparison involved two TrumpJet chemical mixers installed on the bottom wire trays. The second element of comparison involved the improvement brought by a third TrumpJet chemical mixer installed on the top wire tray. This second comparison of the efficient defoamer feeding concept was made at a higher production speed of PM8. The air content control situation was also studied at the higher production speed. In addition the connection between the defoamer and air content was observed and a mill-scale system was studied. The economical benefits of the new dosing procedure were also reviewed. Air content profiles of short circulation were measured in the reference situation and the two comparison points of the study. These air content measurements proved the main gas load is introduced to PM8's paper furnish from the white water tray. Thick stock air content was not essential when the air volume flow was considered. The improved defoamer dosing procedure made lower dosage amounts possible. Compared with the traditional feeding system, the new defoamer feeding concept made only few direct improvements to the wet end operations and the produced paper itself. The lower defoamer need was noticed to have a positive influence on hydrophobic sizing and paper defects. The surfaces of the white water tanks and the operation of pumps were assessed based on the density variations of the suspension. The temperature in the white water silo was stated to have a significant influence on the air content measured in the first centrifugal cleaning stage.

Kehittyneiden hitsausprosessien soveltuvuus alumiinin ja hiiliterästen hitsaukseen

Diplomityössä tutkitaan hitsausprosessien kehitystä. Työn kirjallisen osan alku kuvaa hitsauksen nykypäivää ja tulevaisuutta sekä millainen on hitsaava Suomi. Kehittyneiden hitsausprosessien tarkastelu on jaettu hiiliterästen ja alumiinien hitsausprosesseihin. Hiiliteräksien hitsauksen osalta työssä esitellään kitkahitsaus pyörivällä työkalulla, muunnettu lyhytkaarihitsaus, laserhitsaus, laser-hybridihitsaus ja kapearailohitsaus. Alumiinien hitsauksen osalta työssä esitellään laserhitsaus, muunnettu lyhytkaarihitsaus, kitkahitsaus pyörivällä työkalulla ja vaihtovirta MIG hitsaus. Diplomityön käytännönosuudessa todennettiin hitsausprosessien kehitys. Ensimmäisissä hitsauskokeissa hitsattiin merialumiinia eri kaarityypeillä. Vertailua tehdään pulssihitsauksen, lankapulssihitsauksen sekä CMT-kaarihitsauksen välillä. Koehitsaukset osoittavat CMT-hitsauksen tuottavan MIG-pulssihitsausta pienemmät hitsausmuodonmuutokset. CMT-hitsauksessa alumiinin oksidikerros aiheuttaa MIGpulssihitsausta vähemmän ongelmia, sillä kaari syttyy varmemmin suurillakin hitsausnopeuksilla, eikä hitsiin synny huokosia. Hitsausnopeudella 40 cm/min lankapulssihitsauksella ja MIG-pulssihitsauksella päittäisliitoksena hitsattujen vesileikattujen alumiinikappaleiden hitseihin ei syntynyt huokosia. Kokeen perusteella voidaan todeta, ettei oksidikerroksella ollut vaikutusta hitsin onnistumiseen. Hitsauskokeiden toinen osio tutkii hiilimangaaniteräksisen T-palkin kuitulaserhitsausta. Viiden kilowatin laserteholla hitsattiin onnistuneesti viisi metriä pitkiä T-palkkeja hitsausnopeudella 2 m/min. Takymetrimittauksella ja Tritop 3D-koordinaattimittauksella todennettiin laserhitsatun T-palkin hitsausmuodonmuutosten olevan huomattavasti Twin-jauhekaarihitsauksella hitsattua T-palkkia pienemmät.

Web Application Performance Testing

Web application performance testing is an emerging and important field of software engineering. As web applications become more commonplace and complex, the need for performance testing will only increase. This paper discusses common concepts, practices and tools that lie at the heart of web application performance testing. A pragmatic, hands-on approach is assumed where applicable; real-life examples of test tooling, execution and analysis are presented right next to the underpinning theory. At the client-side, web application performance is primarily driven by the amount of data transmitted over the wire. At the server-side, selection of programming language and platform, implementation complexity and configuration are the primary contributors to web application performance. Web application performance testing is an activity that requires delicate coordination between project stakeholders, developers, system administrators and testers in order to produce reliable and useful results. Proper test definition, execution, reporting and repeatable test results are of utmost importance. Open-source performance analysis tools such as Apache JMeter, Firebug and YSlow can be used to realise effective web application performance tests. A sample case study using these tools is presented in this paper. The sample application was found to perform poorly even under the moderate load incurred by the sample tests.

Tasajännitetason nosto polttokennosovelluksessa

Polttokennojen, erityisesti SOFC-kennojen, tutkimuksessa on viime vuosina saavutettu merkittäviä edistysaskelia ja mahdollisuudet kennojen laajamittaiseen hyödyntämiseen paranevat koko ajan. Polttokennojen yleistyessä tarvitaan tehoelektroniikkaa muokkaamaan kennojen tasajännite verkkoon sopivaksi vaihtojännitteeksi. Verkkovaihtosuuntaaja vaatii korkeamman jännitetason, kuin polttokennosta on saatavissa, joten tasajännitetasoa on ensin nostettava. Tässä diplomityössä esitellään kolme eri hakkuritopologiaa ja perehdytään kokosiltahakkurin optimointiin. Hakkurin pääasialliset häviölähteet olivat toision diodisilta ja transistorit. Diodien vaihtaminen piidiodeista piikarbididiodeihin ei parantanut hyötysuhdetta, koska toision jännite tarkastellussa sovelluksessa oli matala. Muuntajan käämiminen litz-johtimella paransi hyötysuhdetta merkittävästi.

Pretreatment in membrane filtration of wood hydrolysate

Interest in recovery of valuable components from process streams has increased in recent years. Purpose of biorefinery is to utilize components that otherwise would go to waste. Hemicelluloses, for example, could be utilized in production of many valuable products. One possible way to separate and fractionate hemicelluloses is membrane filtration. In the literature part of this work membrane fouling in filtration processes of pulp and paper process- and wastewaters was investigated. Especially purpose was to find out the possible fouling compounds, after which facilities to remove or modify such components less harmful were studied. In the experimental part different pretreatment methods, mainly to remove or degrade lignin from wood hydrolysate, were studied. In addition, concentration of hemicelluloses and separation from lignin were examined with two ultrafiltration membranes; UFX5 and RC70PP. Changes in feed solution, filtration capacity and fouling of membranes were used to evaluate the effects of pretreatment methods. Changes in hydrolysate composition were observed with different analysis methods. Filtration of hydrolysate proved to be challenging, especially with the UFX5 membrane. The more hydrophilic RC70PP membrane did not seem to be fouled as severely as the UFX5 membrane, according to pure water flux measurements. The UFX5 membrane retained hemicelluloses rather well, but problems arose from rapid flux decline resulting from concentration polarization and fouling of membrane. Most effective pretreatment methods in the case with the UFX5 membrane proved to be prefiltration with the RC70PP membrane, activated carbon adsorption and photocatalytic oxidation using titanium dioxide and UV radiation. An additional experiment with PHW extract showed that pulsed corona discharge treatment degraded lignin quite efficiently and thus improved filtration capacity remarkably, even over six times compared to the filtration with untreated extract.

Happidispersion karakterisointi laboratoriosekoittimessa

Työn tarkoituksena oli tarkastella uutta kuvantamistekniikkaa käyttäen happikaasun dispergointia keskisakeuksisen massasuspension joukkoon laboratoriosekoittimessa. Työssä pyrittiin tarkastelemaan muodostuvan dispersion homogeenisuutta neljästä eri kuvauspisteestä sekoittimen kannesta ja kyljestä. Samalla tarkasteltiin myös sekoittimen tehonkulutusta sekä tehonkulutuksen ja aikaansaadun dispersion välistä yhteyttä. Työn yhtenä tarkoituksena oli myös tarkastella uuden kuvantamistekniikan mahdollisuuksia tämäntyyppisissä sovellutuksissa, sillä työ kuuluu PulpVision-projektiin, jossa kehitetään massa- ja paperiteollisuuden uusia konenäkösovellutuksia. Työn kokeellinen osuus koostui sekoituskokeista, joissa tarkasteltiin neljästä kuvauspisteestä kahdella sekoittimen nopeudella mänty- ja koivususpensioihin muodostuvaa kuplakokojakaumaa. Sekoituskokeiden lisäksi tehtiin tehonkulutuskokeita, joissa tarkasteltiin sekoittimen tehonkulutusta sekoittimen täyttöasteen funktiona koivu- ja mäntysuspensioilla sekä vedellä. Työn tuloksien perusteella todettiin, että koivususpensiosta havaittujen kuplien pinta-ala oli noin puolet mäntysuspensiosta havaittujen kuplien pinta-alasta. Sekoittimen roottorin pyörimisnopeuden puolittuessa suspensioon dispergoidun hapen kuplakoko kasvoi huomattavasti. Neljästä kuvausyhteestä tarkasteltuna havaittiin pienimpien kuplien esiintyvän sekoittimen alaosassa. Mäntysuspension tehonkulutuksen havaittiin kasvavan viidenneksellä, kun sekoittimen täyttöaste kasvoi 10 %, kun taas koivususpension tehonkulutuksen kasvu oli tästä vain puolet. Kuvantamislaitteiston todettiin olevan tämänkaltaiseen sovellutukseen riittävä, varsinkin kun valonlähteenä käytetään pulssilaseria.

Spectroscopic monitoring during laser welding of aluminium alloy

The mechanical properties of aluminium alloys are strongly influenced by the alloying elements and their concentration. In the case of aluminium alloy EN AW-6060 the main alloying elements are magnesium and silicon. The first goal of this thesis was to determine stability, repeatability and sensitivity as figures of merit of the in-situ melt identification technique. In this study the emissions from the laser welding process were monitored with a spectrometer. With the information produced by the spectrometer, quantitative analysis was conducted to determine the figures of merit. The quantitative analysis concentrated on magnesium and aluminium emissions and their relation. The results showed that the stability of absolute intensities was low, but the normalized magnesium emissions were quite stable. The repeatability of monitoring magnesium emissions was high (about 90 %). Sensitivity of the in-situ melt identification technique was also high. As small as 0.5 % change in magnesium content was detected by the spectrometer. The second goal of this study was to determine the loss of mass during deep penetration laser welding. The amount of magnesium in the material was measured before and after laser welding to determine the loss of magnesium. This study was conducted for aluminium alloy with nominal magnesium content of 0-10 % and for standard material EN AW-6060 that was welded with filler wire AlMg5. It was found that while the magnesium concentration in the material changed, the loss of magnesium remained fairly even. Also by feeding filler wire, the behaviour was similar. Thirdly, the reason why silicon had not been detected in the emission spectrum needed to be explained. Literature research showed that the amount of energy required for silicon to excite is considerably higher compared to magnesium. The energy input in the used welding process is insufficient to excite the silicon atoms.

Modeling and Analysis of Noise and Interconnects for On-Chip Communication Link Design

This thesis considers modeling and analysis of noise and interconnects in onchip communication. Besides transistor count and speed, the capabilities of a modern design are often limited by on-chip communication links. These links typically consist of multiple interconnects that run parallel to each other for long distances between functional or memory blocks. Due to the scaling of technology, the interconnects have considerable electrical parasitics that affect their performance, power dissipation and signal integrity. Furthermore, because of electromagnetic coupling, the interconnects in the link need to be considered as an interacting group instead of as isolated signal paths. There is a need for accurate and computationally effective models in the early stages of the chip design process to assess or optimize issues affecting these interconnects. For this purpose, a set of analytical models is developed for on-chip data links in this thesis. First, a model is proposed for modeling crosstalk and intersymbol interference. The model takes into account the effects of inductance, initial states and bit sequences. Intersymbol interference is shown to affect crosstalk voltage and propagation delay depending on bus throughput and the amount of inductance. Next, a model is proposed for the switching current of a coupled bus. The model is combined with an existing model to evaluate power supply noise. The model is then applied to reduce both functional crosstalk and power supply noise caused by a bus as a trade-off with time. The proposed reduction method is shown to be effective in reducing long-range crosstalk noise. The effects of process variation on encoded signaling are then modeled. In encoded signaling, the input signals to a bus are encoded using additional signaling circuitry. The proposed model includes variation in both the signaling circuitry and in the wires to calculate the total delay variation of a bus. The model is applied to study level-encoded dual-rail and 1-of-4 signaling. In addition to regular voltage-mode and encoded voltage-mode signaling, current-mode signaling is a promising technique for global communication. A model for energy dissipation in RLC current-mode signaling is proposed in the thesis. The energy is derived separately for the driver, wire and receiver termination.

Evolution of Bordetella pertussis post vaccination

Evolution of Bordetella pertussis post vaccination Whooping cough or pertussis is caused by the gram-negative bacterium Bordetella pertussis. It is a highly contiguous disease in the human respiratory tract. Characteristic of pertussis is a paroxysmal cough with whooping sound during gasps of breath after coughing episodes. It is potentially fatal to unvaccinated infants. The best approach to fight pertussis is to vaccinate. Vaccinations against pertussis have been available from the 1940s. Traditionally vaccines were whole-cell pertussis (wP) preparations as part of the combined diphtheria-tetanus-pertussis (DTP) vaccines. More recently acellular pertussis (aP) vaccines have replaced the wP vaccines in many countries. The aP vaccines are less reactogenic and can also be administered to school children and adults. There are several publications reporting variation in the i>B. pertussis virulence factors that are also aP vaccine antigens. This has occurred in the genes coding for pertussis toxin and pertactin about 15 to 30 years after the introduction of pertussis vaccines to immunisation programs. Resurgence of pertussis has also been reported in many countries with high vaccination coverage. In this study the evolution of B. pertussis was investigated in Finland, the United Kingdom, Poland, Serbia, China, Senegal and Kenya. These represent countries with a long history of high vaccination coverage with stable vaccines or changes in the vaccine formulation; countries which established high vaccination coverage late; and countries where vaccinations against pertussis were started late. With bacterial cytotoxicity and cytokine measurements, comparative genomic hybridisation, pulsed-field gel electrophoresis (PFGE), genotyping and serotyping it was found that changes in the vaccine composition can postpone the emergence of antigenic variants. It seems that the change in PFGE profiles and the loss of genetic material in the genome of B. pertussis are similar in most countries and the vaccine-induced immunity is selecting non-vaccine type strains. However, the differences in the formulation of the vaccines, the vaccination programs and in the coverage of pertussis vaccination have affected the speed and timing of these changes.

Kapearailotekniikan käyttö jauhekaarihitsauksessa

Diplomityössä tavoitteena oli tutkia kapearailojauhekaaritekniikan soveltuvuutta konepajakäyttöön ja sen vaikutusta hitsauksen tuottavuuteen sekä hitsin mekaanisiin ominaisuuksiin. Työ tehtiin vertailukokeilla, jossa koehitsaukset suoritettiin eri aineenpaksuuksille siten, että jokaiselle tutkimuksen kohteena olleelle materiaalille tehtiin yksi hitsaus käytössä olevalla jauhekaaritekniikalla, jolloin saatiin vertailukohde, johon uutta kapearailotekniikkaa verrattiin. Tulokset osoittivat, että kapearailotekniikalla 1 palko/palkokerros aineenpaksuudeltaan Pl. 60 mm koekappale saatiin hitsattua n. 39 % nopeammin verrattuna perinteiseen tandem -hitsaukseen. Kyseisellä aineenpaksuudella lisäainelangan kulutus oli n. 41 % ja jauheen kulutus n. 71 % pienempi verrattuna perinteiseen X- railohitsaukseen tandem -menetelmällä. Lisäksi tuli esille, että ”palkoa palonpäälle” -tekniikka on kapearailotekniikoista tehokkain, sillä 2 palkoa/palkokerros menetelmässä railon leveyttä jouduttiin leventämään, jolloin kapearailotekniikan pieni railotilavuus menetettiin. Lisäaineen kulutus tälläkin menetelmällä jäi pienemmäksi verrattuna X- railohitsaukseen. Ennalta pelättyä kuonan irtoamisongelmaa ei kapearailohitsauksessa havaittu, vaan kuona irtosi ongelmitta railon kyljistä. Lisäksi kapearailotekniikalla hitsattujen hitsien lujuudet olivat vertailukelpoiset tandem- ja yksilankamenetelmällä hitsattujen hitsien kanssa.

Welding development of crane main girder

Konecranes Corporation manufactures huge steel structures in 16 factories worldwide, in which the environment and quality varies. The company has a desire to achieve the same weld quality in each factory, regardless of the manufacturing place. The main subject of this master’s thesis was to develop the present box girder crane welding process, submerged arc welding and especially the fillet welding. Throughput time and manufacturing costs can be decreased by welding the full penetration fillet weld without a bevel, changing present groove types for more appropriate ones and by achieving the desired weld quality on the first time. Welding experiments of longitudinal fillet welding were made according to the present challenges, which the manufacturing process is facing. In longitudinal fillet welding tests the main focus was to achieve full penetration fillet weld for 6, 8 and 10 millimeters thick web plates with single and twin wire submerged arc welding. Full penetration was achieved with all the material thicknesses, both with single and twin wire submerged arc welding processes. The main problem concerning the weld was undercutting and shape of the weld bead. The question about insufficiency of presently used power sources with twin wire was risen up during testing, due to the thicknesses that require high welding current. Bigger power source is required when box girders are welded nonstop, if twin wire is used. For single wire process the penetration was achieved with significantly less amperage than with twin wire.

Sellutehtaan vedenkäytön vähentäminen

Työn tarkoituksena oli etsiä mahdollisia kohteita sellutehtaan veden käytön vähen-tämiseksi. Analyysien avulla selvitettiin voidaanko havaittujen kohteiden tällä hetkellä menetettyjä vesivirtoja käyttää uudelleen. Lopuksi arvioitiin miten kierrä-tettävät vedet vaikuttaisivat raakaveden laatuun, mikäli ne yhdistettäisiin tämän joukkoon. Veden käytön vähentämiskohteita etsittiin tutkimalla tehtaan prosessi-kaavioita osastokohtaisesti sekä selvittämällä näin havaittuja kohteita osastoilla. Työn kokeellinen osa koostui vesianalyyseistä. Vesianalyyseissä määritettiin seu-raavat arvot sellutehtaalle tulevasta vedestä: sameus (FTU), kiintoaine, sähkönjoh-tavuus, pH, CODCr, BOD7ATU, kokonaisfosfori P, Mn, Cl, K, Ca, Mg ja AOX. Nämä tehtiin valituista kohteista havaituista tällä hetkellä tehtaalta pois johdetuista mutta mahdollisesti kierrätettävistä vesistä. Työn tuloksien perusteella havaittiin, että seuraavissa tarkasteluun valituissa koh-teissa vedet olivat hyvin puhtaita ja talteen otettavia kierrätykseen. Näitä olivat savukaasupesurin vedet, sekundäärilauhdesäiliön vedet sekä tiivistevedet. Haih-duttamon lämminvesisäiliön sekä kuivauskone 4 kiertovesitornin vedet olivat hieman likaantuneet mutta hyvin kierrätettävissä. Koivulinjan D0-vaiheen, havu-linjan D1-vaiheen sekä kuivauskone 4 lajittamon vesivirtoja ei likaantumisen vuoksi kannattanut kerätä hyötykäyttöön.

Uittonippujen sidelangan valinta ja sitomiskonstruktion suunnittelu

Työssä suunniteltiin uittonippujen sidonnan koneellistamiseksi tarvittavan sidontalangan käsittelylaitteisto. Sen toiminnalliset pääkomponentit ovat langan ohjauskouru, syöttölaite sekä solminta- ja katkaisulaitteet. Lisäksi työssä tehtiin koneelliseen sidontaan sopivan sidontalangan määrityksiä.