Optical spectroscopy of organic material based on C60

The structure and optical properties of thin films based on C60 materials are studied. Reproducible vacuum method of thin fullerene films production with Cd impurity on Si, glass and mica surfaces is developed. Surface morphology of the films are investigated by AFM and SEM methods. The ab initio quantum - chemical calculations of the geometry, total energy and excited energy states of complex fullerene- cadmium telluride supramolecules are performed. Photoluminescence spectra of composite thin films based on C60 before and after X-ray irradiation were measured. The intensity of additional peaks is defined as the charge composition due to the type of substrate. These results are interpreted as an appearance of the dipole-allowed transitions in the fullerene excited singlet states spectrum cause of an interference with cadmium telluride. X-ray irradiated films were investigated, and additional peaks in photoluminescence spectra were detected. These peaks appear as a result of molecular complexes formation from C60CdTe mixture and dimerization of the films. Density functional B3LYP quantum-chemical calculations for C60CdTe, molecular complexes, (C60)2 and C120O dimers were performed to elucidate some experimental results.

Enhancement of ultrafiltration process by pretreatment in recovery of hemicelluloses from wood extracts

Hemicelluloses are potential raw material for several items produced in future wood-based biorefineries. One possible method for recovering hemicelluloses from wood extracts is ultrafiltration (UF). However, low filtration capacities and severe fouling restrict the use of tight UF membranes in the treatment of wood extracts. The lack of suitable commercial membranes creates a need for pretreatment which would decrease fouling and increase the filtration capacity. This thesis focuses on the evaluation of the possibility to improve the filtration capacity and decrease fouling with the pretreatment of wood extracts. Methods which remove harmful compounds and methods which degrade them are studied, as well as combinations of the methods. The tested pretreatments have an influence on both the concentration of different compounds and the molecular mass distribution of the compounds in the extract. This study revealed that in addition to which kind of compounds were removed, also the change in molecular size distribution affected the filtration capacity significantly. It was shown that the most harmful compounds for the filtration capacity of the hydrophobic 5 kDa membrane were the ones capable of permeating the membrane and fouling also the inner membrane structure. Naturally, the size of the most harmful compounds depends on the used UF membrane and is thus case-specific. However, in the choice of the pretreatment method, the focus should be on the removal of harmful compound sizes rather than merely on the total amount of removed foulants. The results proved that filtration capacity can be increased with both adsorptive and oxidative pretreatments even by hundreds of per cents. For instance, the use of XAD7 and XAD16 adsorbents increased the average flux in the UF of a birch extract from nearly zero to 107 kg/(m2h) and 175 kg/(m2h), respectively. In the treatment of a spruce extract, oxidation by pulsed corona discharge (PCD) increased the flux in UF from 46 kg/(m2h) to 158 kg/(m2h). Moreover, when a birch extract batch was treated with laccase enzyme, the flux in UF increased from 15 kg/(m2h) to 36 kg/(m2h). However, fouling was decreased only by adsorptive pretreatment while oxidative methods had a negligible or even negative impact on it. This demonstrates that filtration capacity and fouling are affected by different compounds and mechanisms. The results of this thesis show that filtration capacity can be improved and fouling decreased through appropriate pretreatment. However, the choice of the best possible pretreatment is case-specific and depends on the wood extract and the membrane used. Finding the best option requires information on the extract content and membrane characteristics as well as on the filtration performance of the membrane in the prevailing conditions and a multivariate approach. On the basis of this study, it can be roughly concluded that adsorptive pretreatment improves the filtration capacity and decreases fouling rather reliably, but it may lead to significant hemicellulose losses. Oxidation reduces the loss of valuable hemicelluloses and could improve the filtration capacity, but fouling challenges may remain. Combining oxidation with adsorptive pretreatment was not a solution for avoiding hemicellulose losses in the tested cases.

Two-dimensional drift-diffusion simulation of organic solar cells

The aim of this master's thesis is to develop a two-dimensional drift-di usion model, which describes charge transport in organic solar cells. The main bene t of a two-dimensional model compared to a one-dimensional one is the inclusion of the nanoscale morphology of the active layer of a bulk heterojunction solar cell. The developed model was used to study recombination dynamics at the donor-acceptor interface. In some cases, it was possible to determine e ective parameters, which reproduce the results of the two-dimensional model in the one-dimensional case. A summary of the theory of charge transport in semiconductors was presented and discussed in the context of organic materials. Additionally, the normalization and discretization procedures required to nd a numerical solution to the charge transport problem were outlined. The charge transport problem was solved by implementing an iterative scheme called successive over-relaxation. The obtained solution is given as position-dependent electric potential, free charge carrier concentrations and current densities in the active layer. An interfacial layer, separating the pure phases, was introduced in order to describe charge dynamics occurring at the interface between the donor and acceptor. For simplicity, an e ective generation of free charge carriers in the interfacial layer was implemented. The pure phases simply act as transport layers for the photogenerated charges. Langevin recombination was assumed in the two-dimensional model and an analysis of the apparent recombination rate in the one-dimensional case is presented. The recombination rate in a two-dimensional model is seen to e ectively look like reduced Langevin recombination at open circuit. Replicating the J-U curves obtained in the two-dimensional model is, however, not possible by introducing a constant reduction factor in the Langevin recombination rate. The impact of an acceptor domain in the pure donor phase was investigated. Two cases were considered, one where the acceptor domain is isolated and another where it is connected to the bulk of the acceptor. A comparison to the case where no isolated domains exist was done in order to quantify the observed reduction in the photocurrent. The results show that all charges generated at the isolated domain are lost to recombination, but the domain does not have a major impact on charge transport. Trap-assisted recombination at interfacial trap states was investigated, as well as the surface dipole caused by the trapped charges. A theoretical expression for the ideality factor n_id as a function of generation was derived and shown to agree with simulation data. When the theoretical expression was fitted to simulation data, no interface dipole was observed.