Development of filter media treatments for liquid filtration

Woven monofilament, multifilament, and spun yarn filter media have long been the standard media in liquid filtration equipment. While the energy for a solid-liquid separation process is determined by the engineering work, it is the interface between the slurry and the equipment - the filter media - that greatly affects the performance characteristics of the unit operation. Those skilled in the art are well aware that a poorly designed filter medium may endanger the whole operation, whereas well-performing filter media can make the operation smooth and economical. As the mineral and pulp producers seek to produce ever finer and more refined fractions of their products, it is becoming increasingly important to be able to dewater slurries with average particle sizes around 1 ¿m using conventional, high-capacity filtration equipment. Furthermore, the surface properties of the media must not allow sticky and adhesive particles to adhere to the media. The aim of this thesis was to test how the dirt-repellency, electrical resistance and highpressure filtration performance of selected woven filter media can be improved by modifying the fabric or yarn with coating, chemical treatment and calendering. The results achieved by chemical surface treatments clearly show that the woven media surface properties can be modified to achieve lower electrical resistance and improved dirt-repellency. The main challenge with the chemical treatments is the abrasion resistance and, while the experimental results indicate that the treatment is sufficiently permanent to resist standard weathering conditions, they may still prove to be inadequately strong in terms of actual use.From the pressure filtration studies in this work, it seems obvious that the conventional woven multifilament fabrics still perform surprisingly well against the coated media in terms of filtrate clarity and cake build-up. Especially in cases where the feed slurry concentration was low and the pressures moderate, the conventional media seemed to outperform the coated media. In the cases where thefeed slurry concentration was high, the tightly woven media performed well against the monofilament reference fabrics, but seemed to do worse than some of the coated media. This result is somewhat surprising in that the high initial specific resistance of the coated media would suggest that the media will blind more easily than the plain woven media. The results indicate, however, that it is actually the woven media that gradually clogs during the coarse of filtration. In conclusion, it seems obvious that there is a pressure limit above which the woven media looses its capacity to keep the solid particles from penetrating the structure. This finding suggests that for extreme pressures the only foreseeable solution is the coated fabrics supported by a strong enough woven fabric to hold thestructure together. Having said that, the high pressure filtration process seems to follow somewhat different laws than the more conventional processes. Based on the results, it may well be that the role of the cloth is most of all to support the cake, and the main performance-determining factor is a long life time. Measuring the pore size distribution with a commercially available porometer gives a fairly accurate picture of the pore size distribution of a fabric, but failsto give insight into which of the pore sizes is the most important in determining the flow through the fabric. Historically air, and sometimes water, permeability measures have been the standard in evaluating media filtration performance including particle retention. Permeability, however, is a function of a multitudeof variables and does not directly allow the estimation of the effective pore size. In this study a new method for estimating the effective pore size and open pore area in a densely woven multifilament fabric was developed. The method combines a simplified equation of the electrical resistance of fabric with the Hagen-Poiseuille flow equation to estimate the effective pore size of a fabric and the total open area of pores. The results are validated by comparison to the measured values of the largest pore size (Bubble point) and the average pore size. The results show good correlation with measured values. However, the measured and estimated values tend to diverge in high weft density fabrics. This phenomenon is thought to be a result of a more tortuous flow path of denser fabrics, and could most probably be cured by using another value for the tortuosity factor.

Validation Studies of Thermal-hydraulic Code for Safety Analysis of Nuclear Power Plants

This thesis gives an overview of the validation process for thermal hydraulic system codes and it presents in more detail the assessment and validation of the French code CATHARE for VVER calculations. Three assessment cases are presented: loop seal clearing, core reflooding and flow in a horizontal steam generator. The experience gained during these assessment and validation calculations has been used to analyze the behavior of the horizontal steam generator and the natural circulation in the geometry of the Loviisa nuclear power plant. The cases presented are not exhaustive, but they give a good overview of the work performed by the personnel of Lappeenranta University of Technology (LUT). Large part of the work has been performed in co-operation with the CATHARE-team in Grenoble, France. The design of a Russian type pressurized water reactor, VVER, differs from that of a Western-type PWR. Most of thermal-hydraulic system codes are validated only for the Western-type PWRs. Thus, the codes should be assessed and validated also for VVER design in order to establish any weaknesses in the models. This information is needed before codes can be used for the safety analysis. Theresults of the assessment and validation calculations presented here show that the CATHARE code can be used also for the thermal-hydraulic safety studies for VVER type plants. However, some areas have been indicated which need to be reassessed after further experimental data become available. These areas are mostly connected to the horizontal stem generators, like condensation and phase separation in primary side tubes. The work presented in this thesis covers a large numberof the phenomena included in the CSNI code validation matrices for small and intermediate leaks and for transients. Also some of the phenomena included in the matrix for large break LOCAs are covered. The matrices for code validation for VVER applications should be used when future experimental programs are planned for code validation.

Effect of Noncondensable Gases on Circulation of Primary Coolant in Nuclear Power Plants in Abnormal Situations

The present study focuses on two effects of the presence of a noncondensable gas on the thermal-hydraulic behavior of thecoolant of the primary circuit of a nuclear reactor in the VVER-440 geometry inabnormal situations. First, steam condensation with the presence of air was studied in the horizontal tubes of the steam generator (SG) of the PACTEL test facility. The French thermal-hydraulic CATHARE code was used to study the heat transfer between the primary and secondary side in conditions derived from preliminary experiments performed by VTT using PACTEL. In natural circulation and single-phase vapor conditions, the injection of a volume of air, equivalent to the totalvolume of the primary side of the SG at the entrance of the hot collector, did not stop the heat transfer from the primary to the secondary side. The calculated results indicate that air is located in the second half-length (from the mid-length of the tubes to the cold collector) in all the tubes of the steam generator The hot collector remained full of steam during the transient. Secondly, the potential release of the nitrogen gas dissolved in the water of the accumulators of the emergency core coolant system of the Loviisa nuclear power plant (NPP) was investigated. The author implemented a model of the dissolution and release ofnitrogen gas in the CATHARE code; the model created by the CATHARE developers. In collaboration with VTT, an analytical experiment was performed with some components of PACTEL to determine, in particular, the value of the release time constant of the nitrogen gas in the depressurization conditions representative of the small and intermediate break transients postulated for the Loviisa NPP. Such transients, with simplified operating procedures, were calculated using the modified CATHARE code for various values of the release time constant used in the dissolution and release model. For the small breaks, nitrogen gas is trapped in thecollectors of the SGs in rather large proportions. There, the levels oscillate until the actuation of the low-pressure injection pumps (LPIS) that refill the primary circuit. In the case of the intermediate breaks, most of the nitrogen gas is expelled at the break and almost no nitrogen gas is trapped in the SGs. In comparison with the cases calculated without taking into account the release of nitrogen gas, the start of the LPIS is delayed by between 1 and 1.75 h. Applicability of the obtained results to the real safety conditions must take into accountthe real operating procedures used in the nuclear power plant.

Propagation of the Ignition Front against Airflow in Packed Beds of Wood Particles

Combustion of wood is increasing because of the needs of decreasing the emissions of carbon dioxide and the amount of waste going to landfills. Wood based fuels are often scattered on a large area. The transport distances should be short enough to prevent too high costs, and so the size of heating and power plants using wood fuels is often rather small. Combustion technologies of small-size units have to be developed to reach efficient and environmentally friendly energy production. Furnaces that use different packed bed combustion or gasification techniques areoften most economic in small-scale energy production. Ignition front propagation rate affects the stability, heat release rate and emissions of packed bed combustion. Ignition front propagation against airflow in packed beds of wood fuels has been studied. The research has been carried out mainly experimentally. Theoretical aspects have been considered to draw conclusions about the experimental results. The effects of airflow rate, moisture content of the fuel, size, shape and density of particles, and porosity of the bed on the propagation rate of the ignition front have been studied. The experiments were carried out in a pot furnace. The fuels used in the experiments were mainly real wood fuels that are often burned in the production of energy. The fuel types were thin wood chips, saw dust, shavings, wood chips, and pellets with different sizes. Also a few mixturesof the above were tested. Increase in the moisture content of the fuel decreases the propagation rates of the ignition front and makes the range of possible airflow rates narrower because of the energy needed for the evaporation of water and the dilution of volatile gases due to evaporated steam. Increase in the airflow rate increases the ignition rate until a maximum rate of propagation is reached after which it decreases. The maximum flame propagation rate is not always reached in stoichiometric combustion conditions. Increase in particle size and density transfers the optimum airflow rate towards fuel lean conditions. Mixing of small and large particles is often advantageous, because small particles make itpossible to reach the maximum ignition rate in fuel rich conditions, and large particles widen the range of possible airflow rates. A correlation was found forthe maximum rate of ignition front propagation in different wood fuels. According to the correlation, the maximum ignition mass flux is increased when the sphericity of the particles and the porosity of the bed are increased and the moisture content of the fuel is decreased. Another fit was found between sphericity and porosity. Increase in sphericity decreases the porosity of the bed. The reasons of the observed results are discussed.

Öljyvahinkojätteiden käsittely alusonnettomuuden jälkeen Kymenlaakson alueen näkökulmasta

Työn tavoitteena oli selvittää Suomenlahden rannalta merkittävän suuruisen alusöljyvahingon jälkeen kerättävän öljyisen jätteen käsittelymahdollisuudet ja -kapasiteetit sekä loppusijoitusmahdollisuudet ja -kapasiteetit Kymenlaakson alueen näkökulmasta. Tarkoituksena oli selvittää, missä jätteiden käsittely voidaan toteuttaa sekä, miten öljyisiä jätteitä voidaan esikäsitellä välivarastoinnin aikana puhdistuksen ja loppusijoituksen tehostamiseksi. Tutkimuksen kohteena oli sekä rannalta kerättävät kiinteät öljyiset ainekset että öljyinen merivesi. Työn alussa on perehdytty jätehuoltovastuuseen, eli kenen vastuulla öljyalusonnettomuuksissa syntyvät öljyiset jätteet ovat. Työssä on esitelty lyhyesti öljyvahinkojätteille teknisesti soveltuvien käsittelymenetelmien periaatteet ja menetelmien rajoituksia käsitellä öljyvahinkojätetteitä. Työssä on myös mainittu aiemmin Suomea koskettaneiden tai maailmalla tapahtuneiden alusöljyvahinkojen jätemääriä ja tapauksissa käytettyjä jätteiden käsittelymenetelmiä. Työ painottuu esittelemään Kymenlaakson alueen laitosten, Riihimäen Ekokem Oy Ab:n ja siirrettävien laitteistojen mahdollisuuksia käsitellä öljyisiä jätteitä. Lisäksi on esitelty öljyisen meriveden käsittelyyn soveltuvia laitoksia Kymenlaakson alueen näkökulmasta. Tietoja on kerätty puhelimitse ja sähköpostitse yritysten edustajilta vuoden 2007 aikana. Kymenlaakson alueella voidaan polttaa voimalaitosten leijupedeissä puhtaaseen polttoaineeseen sekoitettuja öljyisiä orgaanisia aineksia ja murskautuvia puhdistustyössä käytettyjä varusteita noin 10 000 t/a, homogenoitua öljyistä orgaanista ainesta voidaan polttaa Leca-soratehtaan rumpu-uunissa noin 1 200 t/a. Alueen polttokapasiteetti kasvaa, kun työn aikana rakenteilla oleva jätteenpolttolaitos valmistuu ja jätettä voidaan polttaa laitoksen arinalla. Haihtuvilla öljy-yhdisteillä pilaantuneita maa-aineksia voidaan alipainekäsitellä, jos yhdisteet eivät ole haihtuneet jo merellä. Erityisesti öljyiset maaainekset voidaan käsitellä alhaisilla öljypitoisuuksilla (öljypitoisuus noin alle 1-2 %) bitumistabiloimalla, aumakompostoimalla tai pesemällä siirrettävällä pesulaitteistolla. Kymenlaakson alueelle voidaan tuoda myös alueen ulkopuolelta siirrettäviä laitteistoja. Siirrettävät termodesorptiolaitteistot on tehty pilaantuneen maa-aineksen ensisijaiseen käsittelyyn, mutta samalla voidaan käsitellä myös muita jätejakeita, joilla on pieni partikkelikoko (alle 5-10 cm). Savaterra Oy:n siirrettävän termodesorptiolaitteiston kapasiteettiarvio on 100 000 t/a. Myös Niska & Nyyssönen Oy:llä on siirrettävä termodesorptiolaitteisto. Doranova Oy:n siirrettävän pesulaitteiston kapasiteettiarvio on 30 000- 50 000 t/a öljyistä maa-ainesta. Tutkimuksessa on ollut mukana myös Riihimäen Ekokem Oy Ab:n jätevoimala, jonka kapasiteettiarvio on 40 000-45 000 t/a erityisesti öljyisille orgaanisille aineksille, varusteille ja kuolleille eläimille. Riihimäen Ekokem Oy Ab:n ongelmajätelaitoksen rumpuuuneissa voidaan käsitellä arviolta 80 000-100 000 t/a öljyisiä maa-aineksia eli kiinteitä jätteitä, joiden partikkelikoko on suunnilleen alle 10 cm, ja 20 000 t/a nestemäisiä öljyisiä jätteitä. Työn loppupuolella on esitelty myös öljyisen meriveden käsittelyyn soveltuvia laitoksia ja niiden rajoituksia käsitellä kyseistä jätettä. Kyseisten laitosten kapasiteetit selviävät usein vasta onnettomuuden sattuessa. Kaikkiin annettuihin kapasiteettiarvioihin vaikuttaa merkittävästi jätteen koostumus. Raportin lopussa on esitelty alustava toimintasuunnitelma öljyvahinkojätteen käsittelemiseksi. Suunnitelmaan sisältyvät eri jätejakeille laaditut kaaviot, joista voi nähdä muun muassa eri jätekoostumuksille teknisesti soveltuvat käsittelymenetelmät ja käsittelymenetelmiä suorittavat yritykset. Öljyalusonnettomuuden sattuessa soveltuviin yrityksiin tulee ottaa yhteyttä ja selvittää kyseisellä hetkellä vapaana oleva käsittelykapasiteetti. Raportissa on myös esitelty käsittelykustannuksiin vaikuttavia tekijöitä ja arvioitu aiheutuvia kuljetuskustannuksia. Saadut tutkimustulokset ovat hyödynnettävissä erityisesti Kymenlaakson alueella. Tiedot käsittelymenetelmistä ja niiden rajoitteista ovat hyödynnettävissä valtakunnallisesti.

Metsäteollisuuden jätevedenpuhdistamon lietteiden vaihtoehtoiset käsittelymenetelmät.

Työ on tehty osana ympäristöklusterin tutkimusohjelmaa "Materiaalivirrat ja energiankäyttö metsäteollisuusintegraatissa ja niihin liittyvät toimintastrategiat ympäristövaikutuslähtöisesti". Juha Räsänen on tehnyt metsäteollisuuden sivuainevirroista projektissa perusselvityksen, joka on tämän työn pohjana. Työn tavoitteena on ollut selvittää neljän itäsuomalaisen metsäteollisuusintegraatin tapauksissa vaihtoehtoisten lietteenkäsittelymenetelmien tekninen ja taloudellinen soveltuvuus nykyiseen käsittelyyn verrattuna. Tutkimuksessa hyödynnettiin aikaisempia tutkimustuloksia ja eri laitevalmistajien ja metsäteollisuusintegraattien kokemuksia. Työssä esitettäviä arvioita voidaan hyödyntää myös sektoritasolla. Metsäteollisuuden jätevedenpuhdistamon lietteistä käsiteltävyyden kannalta vaativin on bioliete, jonka osuuden kasvaessa perinteinen mekaaninen puristaminen ja poltto vaikeutuvat useilla tehtailla merkittävästikin nykyään ja lähivuosina. Polton ongelmat ja niistä aiheutuva ajoittainen aumakompostointitarve voivat puoltaa joko sekalietteen termistä tai biotermistä kuivausta ennen polttamista. Toinen tapa ratkaista lieteongelma on käsitellä bio- ja primäärilietteet erikseen. Biolietteen lipeälinjakäsittelyssä liete lingotaan, käsitellään mustalipeällä, haihdutetaan ja poltetaan soodakattilassa. Bioliete voidaan myös mädättää ja käsitellä sen jälkeen perinteisessä mekaanisessa puristuksessa. Kaikki käsitellyt menetelmät ovat teknisesti toteutettavissa, kunhan tietyt prosessireunaehdot täyttyvät. Vaihtoehtoiset käsittelymenetelmät vähentävät lietteen jäteluonnetta, mutta vastaavasti kustannukset lisääntyvät usein merkittävästi. Menetelmien käytöstä aiheutuvat integraatin puhdistamolietteen käsittelyn kokonaiskustannukset laskettiin työn osana olevalla taulukkolaskentasovelluksella laitetoimittajien budjettitarjouksia hyödyntäen. Biolietteen poltto soodakattilassa tarjoaa kustannusten kannalta houkuttelevimman ratkaisun. Työhön sisältyvää laskentamenettelyä voidaan soveltaa periaatteessa minkä tahansa metsäteollisuusintegraatin tapaukseen.

Wet Oxidation of TMP Concentrated Paper Mill Process Water. Kinetics of the reaction

Työn tarkoituksena oli tutkia lämpötilan, paineen, pH:n ja katalyytin vaikutusta paperitehtaan TMP-konsentroidun prosessiveden märkähapetuksessa. Teoriaosio sisältää katsauksen sellu- ja paperiteollisuuteen, jätevesien käsittelyyn, nanosuodatuksen ja märkähapetusprosessin toimintaperiaatteet ja sovellukset hybriditeknologialle nanosuodatus-märkähapetuksessa. Empiirinen osa koostuu märkähapetuskokeista eri lämpötiloissa, paineissa, pH:ssa ja eri katalyyseillä. Työssä tutkittiin näiden vaikutusta kemialliseen hapenkulutukseen (COD), Biologiseen hapenkulutukseen (BOD), Välittömästi saatavana olevan biologisen hapenkulutukseen (IABOD), ligniiniin, täysin orgaanisen hiileen (TOC) ja rasvaliukoisten uuteaineiden (LWEs) pitoisuuteen. Tuloksina kokeellisesta työstä saatiin korkeimmat COD:n alenemat ja BOD/COD (biohajoavuus) suurimmilla lämpötilaolosuhteilla (COD:n alenema 70 % ja BOD/COD 97 % 200 °C:ssa ja hapen 10 bar osapaineella). Tutkimuksessa, jossa selvitettiin hapen osapaineen vaikutusta saatiin tuloksena, että hapen osapaineen kasvu parantaa orgaanisen kuormituksen poistoa: COD poisto oli olosuhteilla130°C, 5bar 5 %, olosuhteilla 130 °C, 15bar 15 %, olosuhteilla 170 °C, 5bar 20 % ja olosuhteilla 170 °C, 15bar 50 %. Lähes täydellinen LWEs –poisto saavutettiin 150 °C ja 10bar olosuhteilla, vaikka tässä lämpötilassa ei saavutettu korkeata orgaanisen kuormituksen poistoa. Emäksinen pH vaikutti suosivan hapettavia reaktioita, koska korkein COD:n poisto saavutettiin näissä olosuhteilla; kuitenkin alkalisen väliaineen tehokkuudelle löydettiin tärkeä lämpötilariippuvuus.

Aluminium fouling and its impact on activated carbon based dioxin and furan removal in a wet scrubber at a co-incineration plant

Dioxins and furans, PCDD/Fs, are highly toxic substances formed in post combustion zones in furnaces. PCDD/F emissions are regulated by a waste incineration directive which relates also to co-incineration plants. Several observations of dioxin and furan enhancements in wet scrub- bers have been reported previously. This is thought to be due to the so-called "memory effect" which occurs when dioxins and furans absorb into plastic material in scrubbers and desorb when ambient circumstances alter significantly. At the co-incineration plant involved, dioxins and furans are controlled with a wet scrubber, the tower packing of which is made of plastic in which activated carbon particles are dispersed. This should avoid the memory effect and act as a dioxin and furan sink since dioxins and furans are absorbed irreversibly into the packing ma- terial. In this case, the tower packing in the scrubber is covered with a white layer that has been found to be mainly aluminium. The aim of this thesis was to determine the aluminium balance and the dioxin and furan behaviour in the scrubber and, thus, the impacts that the foul- ing has on dioxin and furan removal. The source of aluminium, reasons for fouling and further actions to minimize its impacts on dioxin and furan removal were also to be discovered. Measurements in various media around the scrubber and in fuels were made and a profile analysis of PCDD/F and mass balance calculations were carried out. PCDD/F content de- creased in the scrubber. The reduced PCDD/F was not discharged into scrubbing water. The removal mechanism seems to work in spite of the fouling, at least with low PCDD/F loads. Most of the PCDD/F in excess water originates from the Kymijoki River which is used as feeding water in the scrubber. Fouling turned out to consist mainly of aluminium hydroxides. Sludge combusted in the furnace was found to be a significant source of aluminium. Ways to minimize the fouling would be adjustment of pH to a proper lever, installation of a mechanical filter to catch the loose material from the scrubbing water and affecting the aluminium content of the sludge.

Reduction and Analysis Methods of Indigo

Throughout history indigo was derived from various plants for example Dyer’s Woad (Isatis tinctoria L.) in Europe. In the 19th century were the synthetic dyes developed and nowadays indigo is mainly synthesized from by-products of fossil fuels. Indigo is a so-called vat dye, which means that it needs to be reduced to its water soluble leucoform before dyeing. Nowadays, most of the industrial reduction is performed chemically by sodium dithionite. However, this is considered environmentally unfavourable because of waste waters contaminating degradation products. Therefore there has been interest to find new possibilities to reduce indigo. Possible alternatives for the application of dithionite as the reducing agent are biologically induced reduction and electrochemical reduction. Glucose and other reducing sugars have recently been suggested as possible environmentally friendly alternatives as reducing agents for sulphur dyes and there have also been interest in using glucose to reduce indigo. In spite of the development of several types of processes, very little is known about the mechanism and kinetics associated with the reduction of indigo. This study aims at investigating the reduction and electrochemical analysis methods of indigo and give insight on the reduction mechanism of indigo. Anthraquinone as well as it’s derivative 1,8-dihydroxyanthraquinone were discovered to act as catalysts for the glucose induced reduction of indigo. Anthraquinone introduces a strong catalytic effect which is explained by invoking a molecular “wedge effect” during co-intercalation of Na+ and anthraquinone into the layered indigo crystal. The study includes also research on the extraction of plant-derived indigo from woad and the examination of the effect of this method to the yield and purity of indigo. The purity has been conventionally studied spectrophotometrically and a new hydrodynamic electrode system is introduced in this study. A vibrating probe is used in following electrochemically the leuco-indigo formation with glucose as a reducing agent.

Thermal-Hydraulic Studies on the Safety Of VVER-440 Type Nuclear Power Plants

This thesis includes several thermal hydraulic analyses related to the Loviisa WER 440 nuclear power plant units. The work consists of experimental studies, analysis of the experiments, analysis of some plant transits and development of a calculational model for calculation of boric acid concentrations in the reactor. In the first part of the thesis, in the case of won of boric acid solution behaviour during long term cooling period of LOCAs, experiments were performed in scaled down test facilities. The experimental data together with the results of RELAPS/MOD3 simulations were used to develop a model for calculations of boric acid concentrations in the reactor during LOCAs. The results of calculations showed that margins to critical concentrations that would lead to boric acid crystallization were large, both in the reactor core and in the lower plenum. This was mainly caused by the fact that water in the primary cooling circuit includes borax (Na)BsO,.IOHZO), which enters the reactor when ECC water is taken from the sump and greatly increases boric acid solubility in water. In the second part, in the case of simulation of horizontal steam generators, experiments were performed with PACTEL integral test loop to simulate loss of feedwater transients. The PACTEL experiments, as well as earlier REWET III natural circulation tests, were analyzed with RELAPS/MOD3 Version Sm5 code. The analysis showed that the code was capable of simulating the main events during the experiments. However, in the case of loss of secondary side feedwater the code was not completely capable to simulate steam superheating in the secondary side of the steam generators. The third part of the work consists of simulations of Loviisa VVER reactor pump trip transients with RELAPSlMODI Eur, RELAPS/MOD3 and CATHARE codes. All three codes were capable to simulate the two selected pump trip transients and no significant differences were found between the results of different codes. Comparison of the calculated results with the data measured in the Loviisa plant also showed good agreement.

Cuticular and Suberin Polymers of Edible Plants. Analysis by Gas Chromatographic-Mass Spectrometric and Solid State Spectroscopic Methods

Cutin and suberin are structural and protective polymers of plant surfaces. The epidermal cells of the aerial parts of plants are covered with an extracellular cuticular layer, which consists of polyester cutin, highly resistant cutan, cuticular waxes and polysaccharides which link the layer to the epidermal cells. A similar protective layer is formed by a polyaromatic-polyaliphatic biopolymer suberin, which is present particularly in the cell walls of the phellem layer of periderm of the underground parts of plants (e.g. roots and tubers) and the bark of trees. In addition, suberization is also a major factor in wound healing and wound periderm formation regardless of the plants’ tissue. Knowledge of the composition and functions of cuticular and suberin polymers is important for understanding the physiological properties for the plants and for nutritional quality when these plants are consumed as foods. The aims of the practical work were to assess the chemical composition of cuticular polymers of several northern berries and seeds and suberin of two varieties of potatoes. Cutin and suberin were studied as isolated polymers and further after depolymerization as soluble monomers and solid residues. Chemical and enzymatic depolymerization techniques were compared and a new chemical depolymerization method was developed. Gas chromatographic analysis with mass spectrometric detection (GC-MS) was used to assess the monomer compositions. Polymer investigations were conducted with solid state carbon-13 cross polarization magic angle spinning nuclear magnetic resonance spectroscopy (13C CP-MAS NMR), Fourier transform infrared spectroscopy (FTIR) and microscopic analysis. Furthermore, the development of suberin over one year of post-harvest storage was investigated and the cuticular layers from berries grown in the North and South of Finland were compared. The results show that the amounts of isolated cuticular layers and cutin monomers, as well as monomeric compositions vary greatly between the berries. The monomer composition of seeds was found to differ from the corresponding berry peel monomers. The berry cutin monomers were composed mostly of long-chain aliphatic ω-hydroxy acids, with various mid-chain functionalities (double-bonds, epoxy, hydroxy and keto groups). Substituted α,ω-diacids predominated over ω-hydroxy acids in potato suberin monomers and slight differences were found between the varieties. The newly-developed closed tube chemical method was found to be suitable for cutin and suberin analysis and preferred over the solvent-consuming and laborious reflux method. Enzymatic hydrolysis with cutinase was less effective than chemical methanolysis and showed specificity towards α,ω-diacid bonds. According to ₁₃C CP-MAS NMR and FTIR, the depolymerization residues contained significant amounts of aromatic structures, polysaccharides and possible cutan-type aliphatic moieties. Cultivation location seems to have effect on cuticular composition. The materials studied contained significant amounts of different types of biopolymers that could be utilized for several purposes with or without further processing. The importance of the so-called waste material from industrial processes of berries and potatoes as a source of either dietary fiber or specialty chemicals should be further investigated in detail. The evident impact of cuticular and suberin polymers, among other fiber components, on human health should be investigated in clinical trials. These by-product materials may be used as value-added fiber fractions in the food industry and as raw materials for specialty chemicals such as lubricants and emulsifiers, or as building blocks for novel polymers.

APROS model validation in case of fast transients in a boiling water reactor

This Master´s thesis investigates the performance of the Olkiluoto 1 and 2 APROS model in case of fast transients. The thesis includes a general description of the Olkiluoto 1 and 2 nuclear power plants and of the most important safety systems. The theoretical background of the APROS code as well as the scope and the content of the Olkiluoto 1 and 2 APROS model are also described. The event sequences of the anticipated operation transients considered in the thesis are presented in detail as they will form the basis for the analysis of the APROS calculation results. The calculated fast operational transient situations comprise loss-of-load cases and two cases related to a inadvertent closure of one main steam isolation valve. As part of the thesis work, the inaccurate initial data values found in the original 1-D reactor core model were corrected. The input data needed for the creation of a more accurate 3-D core model were defined. The analysis of the APROS calculation results showed that while the main results were in good accordance with the measured plant data, also differences were detected. These differences were found to be caused by deficiencies and uncertainties related to the calculation model. According to the results the reactor core and the feedwater systems cause most of the differences between the calculated and measured values. Based on these findings, it will be possible to develop the APROS model further to make it a reliable and accurate tool for the analysis of the operational transients and possible plant modifications.