Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Comparison of Biomass Gasification Technologies for Natural Gas Substitution in Iron Ore Pelletizing Plants

The iron ore pelletizing process consumes high amounts of energy, including nonrenewable sources, such as natural gas. Due to fossil fuels scarcity and increasing concerns regarding sustainability and global warming, at least partial substitution by renewable energy seems inevitable. Gasification projects are being successfully developed in Northern Europe, and large-scale circulating fluidized bed biomass gasifiers have been commissioned in e.g. Finland. As Brazil has abundant biomass resources, biomass gasification is a promising technology in the near future. Biomasses can be converted into product gas through gasification. This work compares different technologies, e.g. air, oxygen and steam gasification, focusing on the use of the product gas in the indurating machine. The use of biosynthetic natural gas is also evaluated. Main parameters utilized to assess the suitability of product gas were adiabatic flame temperature and volumetric flow rate. It was found that low energy content product gas could be utilized in the traveling grate, but it would require burner’s to be changed. On the other hand, bio-SGN could be utilized without any adaptions. Economical assessment showed that all gasification plants are feasible for sizes greater than 60 MW. Bio-SNG production is still more expensive than natural gas in any case.

Defining of the material models for stainless steels to be used in FE modeling

The aim of this work is to study the results of tensile tests for austenitic stainless steel type 304 and make accurate FE-models according to the results of the tests. Tensile tests were made at Central Research Institute of Structural Material, Prometey at Saint Petersburg and Mariyenburg in Russia. The test specimens for the tensile tests were produced at Lappeenranta University of Technology in a Laboratory of Steel Structures. In total 4 different tests were made, two with base material specimens and two with transverse butt weld specimens. Each kind of a specimen was tested at room temperature and at low temperature. By comparing the results of room and low temperature tests of similar test specimen we get to study the results of work hardening that affect the austenitic steels at below room temperature. The produced specimens are to be modeled accurately and then imported for nonlinear FEM- analyzing. Using the data gained from the tensile tests the aim is to get the models work like the specimens did during the tests. By using the analyzed results of the FE-models the aim is to calculate and get the stress-strain curves that correspond to the results acquired from the tensile tests.

Upconverting diagnostics: Multiplex assays utilizing upconversion luminescence technology

Conventional diagnostics tests and technologies typically allow only a single analysis and result per test. The aim of this study was to propose robust and multiplex array-inwell test platforms based on oligonucleotide and protein arrays combining the advantages of simple instrumentation and upconverting phosphor (UCP) reporter technology. The UCPs are luminescent lanthanide-doped crystals that have a unique capability to convert infrared radiation into visible light. No autofluorescence is produced from the sample under infrared excitation enabling the development of highly sensitive assays. In this study, an oligonucleotide array-in-well hybridization assay was developed for the detection and genotyping of human adenoviruses. The study provided a verification of the advantages and potential of the UCP-based reporter technology in multiplex assays as well as anti-Stokes photoluminescence detection with a new anti- Stokes photoluminescence imager. The developed assay was technically improved and used to detect and genotype adenovirus types from clinical specimens. Based on the results of the epidemiological study, an outbreak of adenovirus type B03 was observed in the autumn of 2010. A quantitative array-in-well immunoassay was developed for three target analytes (prostate specific antigen, thyroid stimulating hormone, and luteinizing hormone). In this study, quantitative results were obtained for each analyte and the analytical sensitivities in buffer were in clinically relevant range. Another protein-based array-inwell assay was developed for multiplex serodiagnostics. The developed assay was able to detect parvovirus B19 IgG and adenovirus IgG antibodies simultaneously from serum samples according to reference assays. The study demonstrated that the UCPtechnology is a robust detection method for diverse multiplex imaging-based array-inwell assays.

Reusing repository technology for Cultural Heritage and Special Collections

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Potential and Challenges of Analog Reconfigurable Computation in Modern and Future CMOS

In this work, the feasibility of the floating-gate technology in analog computing platforms in a scaled down general-purpose CMOS technology is considered. When the technology is scaled down the performance of analog circuits tends to get worse because the process parameters are optimized for digital transistors and the scaling involves the reduction of supply voltages. Generally, the challenge in analog circuit design is that all salient design metrics such as power, area, bandwidth and accuracy are interrelated. Furthermore, poor flexibility, i.e. lack of reconfigurability, the reuse of IP etc., can be considered the most severe weakness of analog hardware. On this account, digital calibration schemes are often required for improved performance or yield enhancement, whereas high flexibility/reconfigurability can not be easily achieved. Here, it is discussed whether it is possible to work around these obstacles by using floating-gate transistors (FGTs), and analyze problems associated with the practical implementation. FGT technology is attractive because it is electrically programmable and also features a charge-based built-in non-volatile memory. Apart from being ideal for canceling the circuit non-idealities due to process variations, the FGTs can also be used as computational or adaptive elements in analog circuits. The nominal gate oxide thickness in the deep sub-micron (DSM) processes is too thin to support robust charge retention and consequently the FGT becomes leaky. In principle, non-leaky FGTs can be implemented in a scaled down process without any special masks by using “double”-oxide transistors intended for providing devices that operate with higher supply voltages than general purpose devices. However, in practice the technology scaling poses several challenges which are addressed in this thesis. To provide a sufficiently wide-ranging survey, six prototype chips with varying complexity were implemented in four different DSM process nodes and investigated from this perspective. The focus is on non-leaky FGTs, but the presented autozeroing floating-gate amplifier (AFGA) demonstrates that leaky FGTs may also find a use. The simplest test structures contain only a few transistors, whereas the most complex experimental chip is an implementation of a spiking neural network (SNN) which comprises thousands of active and passive devices. More precisely, it is a fully connected (256 FGT synapses) two-layer spiking neural network (SNN), where the adaptive properties of FGT are taken advantage of. A compact realization of Spike Timing Dependent Plasticity (STDP) within the SNN is one of the key contributions of this thesis. Finally, the considerations in this thesis extend beyond CMOS to emerging nanodevices. To this end, one promising emerging nanoscale circuit element - memristor - is reviewed and its applicability for analog processing is considered. Furthermore, it is discussed how the FGT technology can be used to prototype computation paradigms compatible with these emerging two-terminal nanoscale devices in a mature and widely available CMOS technology.

Improving the usability of extruded wood-plastic composites by using modification technology

Using cellulosic reinforcement to produce plastic composites is a globally growing trend. One of such materials are wood-plastic composites, which are an extensively studied group of materials for which the global industry is looking for new applications. Issues such as bondability, durability and fire resistance still require development to improve the usability of the wood-plastic composite material. Improvement of the usability of wood-plastic composites is studied in this thesis through the effects of using selected modification technology in wood and plastic industry. The applied modification methods are surface by mechanical abrasion and plasma, chemical impregnation of wood flour, and structural modification by the co-extrusion process. The study shows that the properties of WPC can be influenced by the selected modification methods. The selected methods are also found to be able to result as improvement in the properties of the material. The may also affect other than just the targeted properties of the end-product, either in a positive or a negative manner. Therefore modification as performance improvement should be considered as a caseby- case study. Introducing WPC materials for new applications can be done by using modification technology. Structuralmodification can possibly be used to reduce material costs of the modified WPC material.

Forest inventory information needs in Northwest Russia

This thesis applies the customer value hierarchy model to forestry in order to determine strategic options to enhance the value of LiDAR technology in Russian forestry. The study is conducted as a qualitative case study with semi-structured interviews as a main source of the primary data. The customer value hierarchy model constitutes a theoretical base for the research. Secondary data incorporates information on forest resource management, LiDAR technology and Russian forestry. The model is operationalised using forestry literature and forms a basis for analyses of primary data. Analyses of primary data coupled with comprehension of Russian forest inventory system and knowledge on global forest inventory have led to conclusions on the forest inventory methods selection criteria and the organizations that would benefit the most from LiDAR technology use. The thesis recommends strategic options for LiDAR technology’s value enhancement in Russian forestry.

Large scale solar power plant flat roof and carport installation in Finland

This work focuses on the 159.5 kW solar photovoltaic power plant project installed at the Lappeenranta University of Technology in 2013 as an example of what a solar plant project could be in Finland. The project consists of a two row carport and a flat roof installation on the roof of the university laboratories. The purpose of this project is not only its obvious energy savings potential but also to serve as research and teaching laboratory tool. By 2013, there were not many large scale solar power plants in Finland. For this reason, the installation and data experience from the solar power plant at LUT has brought valuable information for similar projects in northern countries. This work includes a first part for the design and acquisition of the project to continue explaining about the components and their installation. At the end, energy produced by this solar power plant is studied and calculated to find out some relevant economical results. For this, the radiation arriving to southern Finland, the losses of the system in cold weather and the impact of snow among other aspects are taken into account.

Forest inventory information needs in Northwest Russia

This research report applies the customer value hierarchy model to forestry in order to determine strategic options to enhance the value of LiDAR technology in Russian forestry. The study is conducted as a qualitative case study with semi-structured interviews as a main source of the primary data. The customer value hierarchy model constitutes a theoretical base for the research. Secondary data incorporates information on forest resource management, LiDAR technology and Russian forestry. The model is operationalised using forestry literature and forms a basis for analyses of primary data. Analyses of primary data coupled with comprehension of Russian forest inventory system and knowledge on global forest inventory have led to conclusions on the forest inventory methods selection criteria and the organizations that would benefit the most from LiDAR technology use. The report recommends strategic options for LiDAR technology’s value enhancement in Russian forestry. This work has been conducted as a part of the project ‘Finnish-Russian Forest Academy 2 - Exploiting and Piloting’, which has been supported financially by the South-East Finland- Russia ENPI CBC 2007-2014 Programme.

Digital Exhaustion in relation to Video Games – The Consumer Perspective

This thesis regards exhaustion of copyright’s distribution right in intangible transfers of video games. It analyses whether, under the current law of the European Union, the phenomenon of digital exhaustion, especially in relation to games exists. The thesis analyses the consumers’ position in the market for copyright protected goods. It uses video games market as an example of the wider phenomenon of the effect of latest technological developments on consumers. The research conducted for the thesis is mostly legal dogmatic, although also comparative analysis, law and economics and law and technology methods are utilised. The thesis evaluates the effects of the most recent case law of the European Court of Justice to analyse the current state of digital exhaustion. In the analysis of effects that the existence of digital exhaustion has, the thesis uses the consumers’ point of view. The thesis introduces the current state of technology in the field of video games from a legal perspective. Furthermore the thesis analyses the effects on consumers of a scenario that no digital exhaustion exists in the future. Such scenario under the recent European case law at the moment seems realistic. The conclusion of my research is most importantly that the consumer position in the market for digital goods has deteriorated and that the probable exclusion of the exhaustion for digital goods is another piece of evidence of this development. Most importantly however, the state of affairs where no certainty prevails on whether digital exhaustion exists, creates injustice from the consumers’ point of view. Accordingly, acts by EU legislators of the Court of Justice of the European Union are required to clarify the issue.

Institutional environment in North Korea: market structure and overcoming institutional voids

Tutkimus sai innoituksensa, kun tutkija huomasi tarpeen liiketaloudelliselle, ajantasaiselle ja realistiselle tutkimukselle Pohjois-Korean markkinoista, joka kuvailisi markkinoiden olemassaolevia ja puuttuvia rakenteita sekä tutkisi mahdollisuuksia ylittää puuttuvat rakenteet. Institutionaalinen teoria valittiin sopivaksi viitekehykseksi kuvailla ja tutkia markkinarakennetta. Tutkimuskysymys muotoiltiin seuraavasti: “Miten ulkomaiset yritykset voivat reagoida puuttuviin markkinarakenteisiin Pohjois-Koreassa?”. Tutkimuskysymys jaettiin kolmeen osakysymykseen: (1) Millainen on Pohjois-Korean markkinoiden institutionaalinen ympäristö? (2) Mitkä ovat merkittävimmät puuttuvat markkinarakenteet Pohjois-Koreassa? (3) Mitä mahdollisuuksia ulkomaisilla yrityksillä voisi olla reagoida puuttuviin markkinarakenteisiin? Tutkimus toteutettiin kvalitatiivisena, koska tutkimuskysymys on deskriptiivinen. Aineisto kerättiin asiantuntijahaastattelun ja kvalitatiivisen sisällönanalyysin keinoin. Primääriaineiston muodostavat 2 asiantuntijahaastattelua ja sekundääriaineiston muodostavat 95 artikkelia, jotka kerättiin 40 lähteestä. Aineisto analysoitiin kvalitatiivisen sisällönanalyysin keinoin. Aineisto koodattiin, luokiteltiin ja esitettiin kokonaisuuksina luokittelurungon avulla, joka laadittiin tutkimusta varten muodostetun teoreettisen viitekehyksen mukaan. Tulokset ja johtopäätökset voidaan tiivistää seuraavasti. (1) Pohjois-Korean markkinan instituutioihin vaikuttaa kaksoisrakenne, jossa muodollinen, sosialistinen rakenne ja epämuodollinen, markkinalähtöinen rakenne toimivat päällekkäin. (2) Puuttuvia rakenteita on sekä markkinan kontekstissa että markkinatasolla. Puutteet ovat osittain seurausta vanhojen rakenteiden korvaantumisesta uusilla, jotka eivät ole institutionalisoituneet. (3) Yritykset voivat käyttää samoja mahdollisuuuksia reagoida puuttuviin markkinarakenteisiin Pohjois-Koreassa, joita kehittyvien markkinoiden yhteydessä on esitetty. Sen tulkittiin vähentävän käsitystä, jonka mukaan Pohjois-Korean markkina on liian erikoinen yritystoiminnalle. (4) Kasvava keskiluokka sekä yrittäjyyden ja naisten yhä merkittävämpi rooli liike-elämässä aiheuttavat alhaalta ylöspäin suuntautuvaa kehitystä markkinoilla. Nämä ovat merkkejä viimeaikaisesta kehityksestä, jotka eivät ole saaneet laajaa huomiota länsimaisessa mediassa. Se korostaa tarvetta liiketaloudelliselle, ajantasaiselle jatkotutkimukselle Pohjois-Korean markkinoista.

Institutional environment in North Korea: market structure and overcoming institutional voids

The research was sparked by an exchange in South Korea, as the author identified a gap in research that provides economic, up to date and realistic information about the North Korean market in English language. A need for a research was identified that would describe the market’s existing and missing market structures and explore possibilities to overcome the missing market structures. Institutional theory was chosen as a suitable framework to describe and explore the market. The research question was formulated as follows: “How can foreign companies overcome institutional voids in the North Korean market?”. To answer the research question, it was divided into three sub-questions as follows: (1) What is the institutional environment in North Korea like? (2) What are the major institutional voids in the North Korean market? (3) What possibilities do foreign companies have to overcome institutional voids? The research is qualitative by nature due to the descriptive and exploratory nature of the research question. Data collection consisted of expert interview and content analysis, resulting in primary data of two interviews and secondary data of 95 articles from 40 different sources. The data was analyzed with the systematical technique of content analysis. The data was coded, classified and presented as concepts with the help of a classification system that was build following the theoretical framework adapted for this study. The findings can be summarized as follows. (1) The market institutions are characterized by an overlapping dual system of formal, socialist structures and informal, market-oriented structures. (2) Institutional voids prevail on both the market’s contextual and on the market level. They are partly result of old institutions being replaced by new institutions that lack institutionalization. (3) Identified possibilities to overcome institutional voids correspond with possibilities drawn from previous research. This decreases the image of North Korea as an impossibly unique market to operate in. (4) Emerging middle class, rapidly growing entrepreneurial activities and women’s increasing role in business drive a down-to-up change in the market. This signals the recent development of the market, yet has been overlooked in the Western media. Thus there is a need for further economic, up to date research concerning North Korea.

Examining human-centered design practice in the mobile apps era

Human-Centered Design (HCD) is a well-recognized approach to the design of interactive computing systems that supports everyday and professional lives of people. To that end, the HCD approach put central emphasis on the explicit understanding of users and context of use by involving users throughout the entire design and development process. With mobile computing, the diversity of users as well as the variety in the spatial, temporal, and social settings of the context of use has notably expanded, which affect the effort of interaction designers to understand users and context of use. The emergence of the mobile apps era in 2008 as a result of structural changes in the mobile industry and the profound enhanced capabilities of mobile devices, further intensify the embeddedness of technology in the daily life of people and the challenges that interaction designers face to cost-efficiently understand users and context of use. Supporting interaction designers in this challenge requires understanding of their existing practice, rationality, and work environment. The main objective of this dissertation is to contribute to interaction design theories by generating understanding on the HCD practice of mobile systems in the mobile apps era, as well as to explain the rationality of interaction designers in attending to users and context of use. To achieve that, a literature study is carried out, followed by a mixed-methods research that combines multiple qualitative interview studies and a quantitative questionnaire study. The dissertation contributes new insights regarding the evolving HCD practice at an important time of transition from stationary computing to mobile computing. Firstly, a gap is identified between interaction design as practiced in research and in the industry regarding the involvement of users in context; whereas the utilization of field evaluations, i.e. in real-life environments, has become more common in academic projects, interaction designers in the industry still rely, by large, on lab evaluations. Secondly, the findings indicate on new aspects that can explain this gap and the rationality of interaction designers in the industry in attending to users and context; essentially, the professional-client relationship was found to inhibit the involvement of users, while the mental distance between practitioners and users as well as the perceived innovativeness of the designed system are suggested in explaining the inclination to study users in situ. Thirdly, the research contributes the first explanatory model on the relation between the organizational context and HCD; essentially, innovation-focused organizational strategies greatly affect the cost-effective usage of data on users and context of use. Last, the findings suggest a change in the nature of HCD in the mobile apps era, at least with universal consumer systems; evidently, the central attention on the explicit understanding of users and context of use shifts from an early requirements phase and continual activities during design and development to follow-up activities. That is, the main effort to understand users is by collecting data on their actual usage of the system, either before or after the system is deployed. The findings inform both researchers and practitioners in interaction design. In particular, the dissertation suggest on action research as a useful approach to support interaction designers and further inform theories on interaction design. With regard to the interaction design practice, the dissertation highlights strategies that encourage a more cost-effective user- and context-informed interaction design process. With the continual embeddedness of computing into people’s life, e.g. with wearable devices and connected car systems, the dissertation provides a timely and valuable view on the evolving humancentered design.