56 resultados para Peat properties
Resumo:
Abstract
Resumo:
Työn tarkoitus oli testata kartonkikoneen lyhyen kierron ilmapitoisuuden merkitystä kartongin ominaisuuksiin. Aluksi työssä selvitettiin ilmapitoisuuden alkutilanne käyttäen kompressioilmiöön perustuvaa ilmapitoisuusmittaria. Sen jälkeen tehtiin kokeita käyttäen POMp-pumppua sekä vaahdonestoainetta. Tarkoituksena oli luoda yhteys prosessin ilmapitoisuuden ja lopputuotteen ominaisuuksien välille. POMp-kokeissa tutkittiin keskipakopumppauksen vaikutusta massan ilmapitoisuuteen. Tuloksista nähdään, että pintakerroksen ilmapitoisuus oli suurempi kuin taustakerroksen, mikä selittyy POMp-pumpun sijainnilla taustakerroksen lyhyessä kierrossa. Vaahdonestoainekokeissa saatiin myös vaikutuksia massan ilmapitoisuuteen. Vaahdonestoaineen lisäyksen jälkeen runkokerroksenilmapitoisuus laski, kun samanaikaisesti pinta- ja taustakerroksen sekä rejektisysteemin ilmapitoisuudet nousivat. Ilmapitoisuuden käytöksen syyksi paljastui lyhyen kierron yhteinen vesikierto ja nykyisille tuotantomäärille alimitoitettu ilmanpoistokapasiteetti. Vaahdonestoaineen lisäyksen jälkeen vedenpoisto parani ja ensimmäisillä kolmella runkokerroksen foililaatikolla havaittiin poistuvan veden virtausten kasvaneen. Samaan aikaan runkokerroksen viiraosan lopulla poistuvan veden virtaukset pienenivät. Kartongin ominaisuuksissa ei havaittu kuitenkaan eroa, vaikka vedenpoisto parani viiraosalla selvästi. Vaahdonestoainekokeiden aikana oli myös tavallista enemmän ajettavuusongelmia, kuten ratakatkoja. Prosessissa esiintyneitä ongelmia ja niihin reagoivia muutosehdotuksia esitellään myös. Vaikein ongelma oli ilman muodostuminen runkokerroksen lyhyessä kierrossa. Ratkaisu voisi koostua isommasta keskikerroksenvesilukkosäiliöstä ja runkokerroksen lyhyen kierron puhdistusveden uudelleen kohdentamisesta. Voisi myös olla hyödyllistä yrittää ilmanpoistoa kemikaalien avulla kiertoveden varastosäiliössä.
Resumo:
Fiber damages comprise fiber deformations, characterized as fiber curl, kink, dislocations and strength losses as well as some yet unidentified factors. This recently discovered phenomenon is especially evident in mill scale kraftpulps. Laboratory produced pulps tend to have less damages and superior strength properties compared to those produced in pulp mills. Generally fiber damages pose a problem in the production of reinforcement pulp because they tend to decrease the ability of fibers to transmit load. Previous studies on fiber damage have shown that most of the fiber damages occur during brown stock processing starting from cooking and discharging. This literature review gives an overall picture on fiber damages occurring during softwood kraft pulp production with an emphasis on the oxygen delignification stage. In addition the oxygen delignification stage itself is described in more detailed extent in order to understand the mechanisms behind the delignification and fiber damaging effect. The literature available on this subject is unfortunately quite contradictory and implicates a lotof different terms. Only a few studies have been published which help to understand the nature of fiber damages. For that reason the knowledge presented in this work is not only based on previous studies but also on research scientist and mill staff interviews.
Resumo:
In this thesis, the sorption and elastic properties of the cation-exchange resins were studied to explain the liquid chromatographic separation of carbohydrates. Na+, Ca2+ and La3+ form strong poly(styrene-co-divinylbenzene) (SCE) as well as Na+ and Ca2+ form weak acrylic (WCE) cation-exchange resins at different cross-link densities were treated within this work. The focus was on the effects of water-alcohol mixtures, mostly aqueous ethanol, and that of the carbohydrates. The carbohydrates examined were rhamnose, xylose, glucose, fructose, arabinose, sucrose, xylitol and sorbitol. In addition to linear chromatographic conditions, non-linear conditions more typical for industrial applications were studied. Both experimental and modeling aspectswere covered. The aqueous alcohol sorption on the cation-exchangers were experimentally determined and theoretically calculated. The sorption model includes elastic parameters, which were obtained from sorption data combined with elasticity measurements. As hydrophilic materials cation-exchangers are water selective and shrink when an organic solvent is added. At a certain deswelling degree the elastic resins go through glass transition and become as glass-like material. Theincreasing cross-link level and the valence of the counterion decrease the sorption of solvent components in the water-rich solutions. The cross-linkage or thecounterions have less effect on the water selectivity than the resin type or the used alcohol. The amount of water sorbed is higher in the WCE resin and, moreover, the WCE resin is more water selective than the corresponding SCE resin. Theincreased aliphatic part of lower alcohols tend to increase the water selectivity, i.e. the resins are more water selective in 2-propanol than in ethanol solutions. Both the sorption behavior of carbohydrates and the sorption differences between carbohydrates are considerably affected by the eluent composition and theresin characteristics. The carbohydrate sorption was experimentally examined and modeled. In all cases, sorption and moreover the separation of carbohydrates are dominated by three phenomena: partition, ligand exchange and size exclusion. The sorption of hydrophilic carbohydrates increases when alcohol is added into the eluent or when carbohydrate is able to form coordination complexes with the counterions, especially with multivalent counterions. Decreasing polarity of the eluent enhances the complex stability. Size exclusion effect is more prominent when the resin becomes tighter or carbohydrate size increases. On the other hand,the elution volumes between different sized carbohydrates decreases with the decreasing polarity of the eluent. The chromatographic separation of carbohydrateswas modeled, using rhamnose and xylose as target molecules. The thermodynamic sorption model was successfully implemented in the rate-based column model. The experimental chromatographic data were fitted by using only one adjustable parameter. In addition to the fitted data also simulated data were generated and utilized in explaining the effect of the eluent composition and of the resin characteristics on the carbohydrate separation.
Resumo:
Environmentally harmful consequences of fossil fuel utilisation andthe landfilling of wastes have increased the interest among the energy producers to consider the use of alternative fuels like wood fuels and Refuse-Derived Fuels, RDFs. The fluidised bed technology that allows the flexible use of a variety of different fuels is commonly used at small- and medium-sized power plants ofmunicipalities and industry in Finland. Since there is only one mass-burn plantcurrently in operation in the country and no intention to build new ones, the co-firing of pre-processed wastes in fluidised bed boilers has become the most generally applied waste-to-energy concept in Finland. The recently validated EU Directive on Incineration of Wastes aims to mitigate environmentally harmful pollutants of waste incineration and co-incineration of wastes with conventional fuels. Apart from gaseous flue gas pollutants and dust, the emissions of toxic tracemetals are limited. The implementation of the Directive's restrictions in the Finnish legislation is assumed to limit the co-firing of waste fuels, due to the insufficient reduction of the regulated air pollutants in the existing flue gas cleaning devices. Trace metals emission formation and reduction in the ESP, the condensing wet scrubber, the fabric filter, and the humidification reactor were studied, experimentally, in full- and pilot-scale combustors utilising the bubbling fluidised bed technology, and, theoretically, by means of reactor model calculations. The core of the model is a thermodynamic equilibrium analysis. The experiments were carried out with wood chips, sawdust, and peat, and their refuse-derived fuel, RDF, blends. In all, ten different fuels or fuel blends were tested. Relatively high concentrations of trace metals in RDFs compared to the concentrations of these metals in wood fuels increased the trace metal concentrations in the flue gas after the boiler ten- to hundred-folds, when RDF was co-fired with sawdust in a full-scale BFB boiler. In the case of peat, lesser increase in trace metal concentrations was observed, due to the higher initial trace metal concentrations of peat compared to sawdust. Despite the high removal rate of most of the trace metals in the ESP, the Directive emission limits for trace metals were exceeded in each of the RDF co-firing tests. The dominat trace metals in fluegas after the ESP were Cu, Pb and Mn. In the condensing wet scrubber, the flue gas trace metal emissions were reduced below the Directive emission limits, whenRDF pellet was used as a co-firing fuel together with sawdust and peat. High chlorine content of the RDFs enhanced the mercuric chloride formation and hence the mercury removal in the ESP and scrubber. Mercury emissions were lower than theDirective emission limit for total Hg, 0.05 mg/Nm3, in all full-scale co-firingtests already in the flue gas after the ESP. The pilot-scale experiments with aBFB combustor equipped with a fabric filter revealed that the fabric filter alone is able to reduce the trace metal concentrations, including mercury, in the flue gas during the RDF co-firing approximately to the same level as they are during the wood chip firing. Lower trace metal emissions than the Directive limits were easily reached even with a 40% thermal share of RDF co-firing with sawdust.Enrichment of trace metals in the submicron fly ash particle fraction because of RDF co-firing was not observed in the test runs where sawdust was used as the main fuel. The combustion of RDF pellets with peat caused an enrichment of As, Cd, Co, Pb, Sb, and V in the submicron particle mode. Accumulation and release oftrace metals in the bed material was examined by means of a bed material analysis, mass balance calculations and a reactor model. Lead, zinc and copper were found to have a tendency to be accumulated in the bed material but also to have a tendency to be released from the bed material into the combustion gases, if the combustion conditions were changed. The concentration of the trace metal in the combustion gases of the bubbling fluidised bed boiler was found to be a summary of trace metal fluxes from three main sources. They were (1) the trace metal flux from the burning fuel particle (2) the trace metal flux from the ash in the bed, and (3) the trace metal flux from the active alkali metal layer on the sand (and ash) particles in the bed. The amount of chlorine in the system, the combustion temperature, the fuel ash composition and the saturation state of the bed material in regard to trace metals were discovered to be key factors affecting therelease process. During the co-firing of waste fuels with variable amounts of e.g. ash and chlorine, it is extremely important to consider the possible ongoingaccumulation and/or release of the trace metals in the bed, when determining the flue gas trace metal emissions. If the state of the combustion process in regard to trace metals accumulation and/or release in the bed material is not known,it may happen that emissions from the bed material rather than the combustion of the fuel in question are measured and reported.
Resumo:
In this study, equations for the calculation of erosion wear caused by ash particles on convective heat exchanger tubes of steam boilers are presented. Anew, three-dimensional test arrangement was used in the testing of the erosion wear of convective heat exchanger tubes of steam boilers. When using the sleeve-method, three different tube materials and three tube constructions could be tested. New results were obtained from the analyses. The main mechanisms of erosionwear phenomena and erosion wear as a function of collision conditions and material properties have been studied. Properties of fossil fuels have also been presented. When burning solid fuels, such as pulverized coal and peat in steam boilers, most of the ash is entrained by the flue gas in the furnace. In bubbling andcirculating fluidized bed boilers, particle concentration in the flue gas is high because of bed material entrained in the flue gas. Hard particles, such as sharp edged quartz crystals, cause erosion wear when colliding on convective heat exchanger tubes and on the rear wall of the steam boiler. The most important ways to reduce erosion wear in steam boilers is to keep the velocity of the flue gas moderate and prevent channelling of the ash flow in a certain part of the cross section of the flue gas channel, especially near the back wall. One can do this by constructing the boiler with the following components. Screen plates can beused to make the velocity and ash flow distributions more even at the cross-section of the channel. Shield plates and plate type constructions in superheaters can also be used. Erosion testing was conducted with three types of tube constructions: a one tube row, an inline tube bank with six tube rows, and a staggered tube bank with six tube rows. Three flow velocities and two particle concentrations were used in the tests, which were carried out at room temperature. Three particle materials were used: quartz, coal ash and peat ash particles. Mass loss, diameter loss and wall thickness loss measurements of the test sleeves were taken. Erosion wear as a function of flow conditions, tube material and tube construction was analyzed by single-variable linear regression analysis. In developing the erosion wear calculation equations, multi-variable linear regression analysis was used. In the staggered tube bank, erosion wear had a maximum value in a tube row 2 and a local maximum in row 5. In rows 3, 4 and 6, the erosion rate was low. On the other hand, in the in-line tube bank the minimum erosion rate occurred in tube row 2 and in further rows the erosion had an increasing value, so that in a six row tube bank, the maximum value occurred in row 6.
Resumo:
The objective of industrial crystallization is to obtain a crystalline product which has the desired crystal size distribution, mean crystal size, crystal shape, purity, polymorphic and pseudopolymorphic form. Effective control of the product quality requires an understanding of the thermodynamics of the crystallizing system and the effects of operation parameters on the crystalline product properties. Therefore, obtaining reliable in-line information about crystal properties and supersaturation, which is the driving force of crystallization, would be very advantageous. Advanced techniques, such asRaman spectroscopy, attenuated total reflection Fourier transform infrared (ATR FTIR) spectroscopy, and in-line imaging techniques, offer great potential for obtaining reliable information during crystallization, and thus giving a better understanding of the fundamental mechanisms (nucleation and crystal growth) involved. In the present work, the relative stability of anhydrate and dihydrate carbamazepine in mixed solvents containing water and ethanol were investigated. The kinetics of the solvent mediated phase transformation of the anhydrate to hydrate in the mixed solvents was studied using an in-line Raman immersion probe. The effects of the operation parameters in terms of solvent composition, temperature and the use of certain additives on the phase transformation kineticswere explored. Comparison of the off-line measured solute concentration and the solid-phase composition measured by in-line Raman spectroscopy allowedthe identification of the fundamental processes during the phase transformation. The effects of thermodynamic and kinetic factors on the anhydrate/hydrate phase of carbamazepine crystals during cooling crystallization were also investigated. The effect of certain additives on the batch cooling crystallization of potassium dihydrogen phosphate (KDP) wasinvestigated. The crystal growth rate of a certain crystal face was determined from images taken with an in-line video microscope. An in-line image processing method was developed to characterize the size and shape of thecrystals. An ATR FTIR and a laser reflection particle size analyzer were used to study the effects of cooling modes and seeding parameters onthe final crystal size distribution of an organic compound C15. Based on the obtained results, an operation condition was proposed which gives improved product property in terms of increased mean crystal size and narrowersize distribution.
Resumo:
Selostus: Ponsiviljeltävyys ja siihen liittyvät geenimerkit peltokauran ja susikauran risteytysjälkeläisissä
Resumo:
High barrier materiaaleilla pyritään pidentämään pakattujen elintarvikkeiden hyllyikää. Barrierin tärkein tehtävä on elintarvikkeen suojaaminen hapelta ja kosteudelta. Alumiinin käyttöä barriermateriaalina pyritään vähentämään korvaamalla alumiini polymeereillä, jotka täyttävät elintarvikkeiden asettamat korkeat säilyvyysvaatimukset. Etyylivinyylialkoholin (EVOH) hapenläpäisevyys on kuivissa olosuhteissa alhaisin kaupallisista muovilaaduista. EVOH tarjoaa myös erinomaisen suojan muita kaasuja, rasvoja, hajuja ja aromeja vastaan ja sitä on helppo prosessoida. Polyamideilla on erinomainen kaasutiiveys sekä hyvä lujuus ja sitkeys. Eri muovilaatuja sekoittamalla voidaan vähentää hapenläpäisyä ja parantaa prosessointia. Polyolefiineja käytetään yleisesti päällystysmateriaaleina, koska ne suojaavat tuotetta erinomaisesti kosteudelta. Hapenläpäisyllä tarkoitetaan hapen kulkeutumista materiaalin läpi joko permeaation kautta tai reikien ja vuotojen läpi. Kaasun permeoitumiseen materiaalin läpi vaikuttavat materiaalin vapaa tilavuus, kiteisyysaste, orientaatio, substituointi, suhteellinen kosteus, lämpötila, barrierkerroksen paksuus, paine-ero ja permeoituvan molekyylin ominaisuudet. Kokeellisessa osassa analysoitiin ja vertailtiin kartonkipohjaisia mehutölkkejä, joissa käytettävät high barrier materiaalit olivat EVOH ja PA. Kartonkipohjaisia alumiinitölkkejä käytettiin referenssinä. Pakkausten hapenläpäisevyysmittauksissa saatiin samasta näytteestä toistettavia tuloksia, vaikka vuotomittauksissa saadut tulokset eivät olleet vertailukelpoisia hapenläpäisytulosten kanssa. Tölkkien valmistus vaikutti oleellisesti pakkausten tiiveysominaisuuksiin. Hapenläpäisy vuotojen ja reikien läpi oli merkittävämpää kuin hapenläpäisy materiaalin läpi. Pakkausten tiiveysominaisuuksia analysoitiin mittaamalla appelsiinimehun askorbiini-happopitoisuus. Askorbiinihapon hajoaminen mitattiin koetölkkeihin pakatusta appelsiinimehusta, ja lämpötilan, valon ja hapen vaikutusta askorbiinihapon hajoamiseen tutkittiin 12 viikon ajan. Lämpötilalla oli suurin vaikutus askorbiinihapon hajoamiseen huolimatta käytetystä pakkausmateriaalista.
Resumo:
Diplomityö tehtiin osana Vapon toteuttamaa monivuotista pelletin kehitysohjelmaa. Kehitysohjelma koostuu useista pienemmistä osaprojekteista, jotka täydentävät toinen toisiaan. Pellettien raaka-ainepohjan laajentaminen on eräs näistä osaprojekteista. Tutkimustyön tavoitteena oli selvittää erilaisten potentiaalisten bioraaka-aineiden soveltuvuutta pelletointiin joko sellaisenaan tai erilaisina seoksina. Raaka-aineiden pelletoitavuutta tutkittiin kenttäolosuhteissa mobiilipelletointilaitoksella. Laitoksen pääkomponentit muodostivat Kahl C 38–780 tasomatriisipuristin, jäähdytin ja täryseula. Pelletointikokeissa tutkittuja raaka-aineita olivat mäntysahanpuru, männynkuori, harvennusranka, haapa, koivu, jyrsinturve ja ruokohelpi. Raaka-aineiden irtotiheys käyttökosteudessa vaihteli välillä 73–244 kg/m3 ja keskimääräinen kosteuspitoisuus 6,5–15 %. Useissa tapauksissa säkitettyjä raaka-aineita säkkikostutettiin haluttuun kosteuspitoisuuteen ennen pelletointia. Säkkikostutettujen raaka-aineiden kosteuspitoisuudet vaihtelivat tällöin välillä 12–14 m- %. Valtaosa tutkituista raaka-aineista ja niiden seoksista pystyttiin pelletoimaan puristimen matriisilla 8/40 mm, jossa puristuskanavan halkaisija oli 8 mm ja kanavan suoran osan pituus 40 mm. Vaikeuksia tuotti ainoastaan pelkän koivupurun ja ruokohelven pelletointi. Käytetty matriisi oli kanavapituudeltaan liian pitkä koivupurun pelletointiin nostaen puristusvastuksen suureksi. Ruokohelven pelletoinnin vaikeudet johtuivat pääasiassa pelletointiin liian karkeasta raaka-aineesta. Myös matriisia 8/55 mm kokeiltiin, mutta se osoittautui liian ”tiukaksi” valtaosalle puuraaka-aineista. Ainoastaan jyrsinturpeen pelletointi onnistui tällä matriisilla. Männynkuoren pelletointia ei matriisilla 8/55 mm yritetty. Kenttäkokeissa valmistetuista pelleteistä määritettiin erilaisia ominaisuuksia, kuten keskipituus, kosteuspitoisuus, irtotiheys, hienoaineksen määrä ja käsittelykestävyys. Lujuus mitattiin sekä Ligno-testillä että CEN-rummutuslujuuden määrityksellä. Lisäksi pelleteille määritettiin alkuaineanalyysi, tuhkapitoisuus ja lämpöarvo ENAS Oy:n laboratoriossa Jyväskylässä. Ligno-testauksessa parhaimman luokan pelletin tulee yltää arvoon 97,5 %. Pelletoitaessa raaka-aineita ja niiden seoksia tasomatriisikoneella sopivalla matriisilla yllettiin usein näihin tai parempiin tuloksiin. Puumateriaaleilla raaka-aineen optimaalinen lähtökosteus oli välillä 12–14 m- % ja turpeella sekä ruokohelvellä 14–16 m- %. Pelletointi onnistui tällöin vaivattomasti, kunhan sopivat puristimen ajoparametrit oli löydetty. Pellettiä alkoi muodostua matriisin puristuskanavien lämpötilan kohotessa noin 70 ºC. Pellettien lämpötila stabiilitilanteessa heti pelletoinnin jälkeen oli useissa tapauksissa 80–90 ºC. Pelletoinnin aikainen tehontarve vaihteli välillä 90–150 kWh/t, ollen suurimmillaan irtotiheydeltään keveillä materiaaleilla. Raaka-aineen suuri partikkelikoko kasvatti puristimen tehontarvetta. Tämä havaittiin selvästi lisättäessä karkeaa ruokohelpisilppua eri raaka-aineiden joukkoon. Kestävyydeltään erinomaisia pellettejä saatiin, kun raaka-aineena oli jyrsinturve, harvennusranka tai mäntypuru. Varsinkin jyrsinturpeen ja harvennusrangan seoksesta valmistetut pelletit osoittautuivat erittäin kestäviksi. Myös jyrsinturpeen ja ruokohelven sekä mäntypurun ja ruokohelven seoksien pelleteille määritettiin hyviä kestävyysarvoja. Männynkuoresta valmistetut pelletit jäivät Ligno-testauksessa kestävyydeltään alle 97,5 % rajan. Pääsyynä tähän oli kuoren pelletointiin käytetyn matriisin 8/40 mm liian lyhyet puristuskanavat.