Underwater Remote Welding Technology for Offshore Structures

The construction of offshore structures, equipment and devices requires a high level of mechanical reliability in terms of strength, toughness and ductility. One major site for mechanical failure, the weld joint region, needs particularly careful examination, and weld joint quality has become a major focus of research in recent times. Underwater welding carried out offshore faces specific challenges affecting the mechanical reliability of constructions completed underwater. The focus of this thesis is on improvement of weld quality of underwater welding using control theory. This research work identifies ways of optimizing the welding process parameters of flux cored arc welding (FCAW) during underwater welding so as to achieve desired weld bead geometry when welding in a water environment. The weld bead geometry has no known linear relationship with the welding process parameters, which makes it difficult to determine a satisfactory weld quality. However, good weld bead geometry is achievable by controlling the welding process parameters. The doctoral dissertation comprises two sections. The first part introduces the topic of the research, discusses the mechanisms of underwater welding and examines the effect of the water environment on the weld quality of wet welding. The second part comprises four research papers examining different aspects of underwater wet welding and its control and optimization. Issues considered include the effects of welding process parameters on weld bead geometry, optimization of FCAW process parameters, and design of a control system for the purpose of achieving a desired bead geometry that can ensure a high level of mechanical reliability in welded joints of offshore structures. Artificial neural network systems and a fuzzy logic controller, which are incorporated in the control system design, and a hybrid of fuzzy and PID controllers are the major control dynamics used. This study contributes to knowledge of possible solutions for achieving similar high weld quality in underwater wet welding as found with welding in air. The study shows that carefully selected steels with very low carbon equivalent and proper control of the welding process parameters are essential in achieving good weld quality. The study provides a platform for further research in underwater welding. It promotes increased awareness of the need to improve the quality of underwater welding for offshore industries and thus minimize the risk of structural defects resulting from poor weld quality.

Impingement jet cooling of end windings in a high-speed electric machine

The rotational speed of high-speed electric machines is over 15 000 rpm. These machines are compact in size when compared to the power rate. As a consequence, the heat fluxes are at a high level and the adequacy of cooling becomes an important design criterion. In the high-speed machines, the air gap between the stator and rotor is a narrow flow channel. The cooling air is produced with a fan and the flow is then directed to the air gap. The flow in the gap does not provide sufficient cooling for the stator end windings, and therefore additional cooling is required. This study investigates the heat transfer and flow fields around the coil end windings when cooling jets are used. As a result, an innovative and new assembly is introduced for the cooling jets, with the benefits of a reduced amount of hot spots, a lower pressure drop, and hence a lower power need for the cooling fan. The gained information can also be applied to improve the cooling of electric machines through geometry modifications. The objective of the research is to determine the locations of the hot spots and to find out induced pressure losses with different jet alternatives. Several possibilities to arrange the extra cooling are considered. In the suggested approach cooling is provided by using a row of air jets. The air jets have three main tasks: to cool the coils effectively by direct impingement jets, to increase and cool down the flow that enters the coil end space through the air gap, and to ensure the correct distribution of the flow by forming an air curtain with additional jets. One important aim of this study is the arrangement of cooling jets in such manner that hot spots can be avoided to wide extent. This enables higher power density in high-speed motors. This cooling system can also be applied to the ordinary electric machines when efficient cooling is needed. The numerical calculations have been performed using a commercial Computational Fluid Dynamics software. Two geometries have been generated: cylindrical for the studied machine and Cartesian for the experimental model. The main parameters include the positions, arrangements and number of jets, the jet diameters, and the jet velocities. The investigated cases have been tested with two widely used turbulence models and using a computational grid of over 500 000 cells. The experimental tests have been made by using a simplified model for the end winding space with cooling jets. In the experiments, an emphasis has been given to flow visualisation. The computational analysis shows good agreement with the experimental results. Modelling of the cooling jet arrangement enables also a better understanding of the complex system of heat transfer at end winding space.

Analysis of Industrial Granular Flow Applications by Using Advanced Collision Models

Granular flow phenomena are frequently encountered in the design of process and industrial plants in the traditional fields of the chemical, nuclear and oil industries as well as in other activities such as food and materials handling. Multi-phase flow is one important branch of the granular flow. Granular materials have unusual kinds of behavior compared to normal materials, either solids or fluids. Although some of the characteristics are still not well-known yet, one thing is confirmed: the particle-particle interaction plays a key role in the dynamics of granular materials, especially for dense granular materials. At the beginning of this thesis, detailed illustration of developing two models for describing the interaction based on the results of finite-element simulation, dimension analysis and numerical simulation is presented. The first model is used to describing the normal collision of viscoelastic particles. Based on some existent models, more parameters are added to this model, which make the model predict the experimental results more accurately. The second model is used for oblique collision, which include the effects from tangential velocity, angular velocity and surface friction based on Coulomb's law. The theoretical predictions of this model are in agreement with those by finite-element simulation. I n the latter chapters of this thesis, the models are used to predict industrial granular flow and the agreement between the simulations and experiments also shows the validation of the new model. The first case presents the simulation of granular flow passing over a circular obstacle. The simulations successfully predict the existence of a parabolic steady layer and show how the characteristics of the particles, such as coefficients of restitution and surface friction affect the separation results. The second case is a spinning container filled with granular material. Employing the previous models, the simulation could also reproduce experimentally observed phenomena, such as a depression in the center of a high frequency rotation. The third application is about gas-solid mixed flow in a vertically vibrated device. Gas phase motion is added to coherence with the particle motion. The governing equations of the gas phase are solved by using the Large eddy simulation (LES) and particle motion is predicted by using the Lagrangian method. The simulation predicted some pattern formation reported by experiment.

Value added logistics in supply and demand chain. Smile. Part 2. eBusiness in a service business. Case: A maintenance and operations network in forest industry

VVALOSADE is a research project of professor Anita Lukka's VALORE research team in the Lappeenranta University of Technology. The VALOSADE includes the ELO technology program of Tekes. SMILE is one of four subprojects of the VALOSADE. The SMILE study focuses on the case of the company network that is composed of small and micro-sized mechanical maintenance service providers and forest industry as large-scale customers. The basic principle of the SMILE study is the communication and ebusiness in supply and demand networks. The aim of the study is to develop ebusiness strategy, ebusiness model and e-processes among the SME local service providers, and onthe other hand, between the local service provider network and the forest industry customers in a maintenance and operations service business. A literature review, interviews and benchmarking are used as research methods in this qualitative case study. The first SMILE report, 'Ebusiness between Global Company and Its Local SME Supplier Network', concentrated on creating background for the SMILE study by studying general trends of ebusiness in supply chains and networks of different industries. This second phase of the study concentrates on case network background, such as business relationships, information systems and business objectives; core processes in maintenance and operations service network; development needs in communication among the network participants; and ICT solutions to respond needs in changing environment. In the theory part of the report, different ebusiness models and frameworks are introduced. Those models and frameworks are compared to empirical case data. From that analysis of the empirical data, therecommendations for the development of the network information system are derived. In process industry such as the forest industry, it is crucial to achieve a high level of operational efficiency and reliability, which sets up great requirements for maintenance and operations. Therefore, partnerships or strategic alliances are needed between the network participants. In partnerships and alliances, deep communication is important, and therefore the information systems in the network also are critical. Communication, coordination and collaboration will increase in the case network in the future, because network resources must be optimised to improve competitive capability of the forest industry customers and theefficiency of their service providers. At present, ebusiness systems are not usual in this maintenance network. A network information system among the forest industry customers and their local service providers actually is the only genuinenetwork information system in this total network. However, the utilisation of that system has been quite insignificant. The current system does not add value enough either to the customers or to the local service providers. At present, thenetwork information system is the infomediary that share static information forthe network partners. The network information system should be the transaction intermediary, which integrates internal processes of the network companies; the network information system, which provides common standardised processes for thelocal service providers; and the infomediary, which share static and dynamic information on right time, on right partner, on right costs, on right format and on right quality. This study provides recommendations how to develop this system in the future to add value to the network companies. Ebusiness scenarios, vision, objectives, strategies, application architecture, ebusiness model, core processes and development strategy must be considered when the network information system will be developed in the next development step. The core processes in the case network are demand/capacity management, customer/supplier relationship management, service delivery management, knowledge management and cash flow management. Most benefits from ebusiness solutions come from the electrifying of operational level processes, such as service delivery management and cash flow management.

On the innovation capacity of technologyrelated knowledge-intensive business services. A case study of the technology and engineering consulting (TEC) sector in Singapore

Even though the research on innovation in services has expanded remarkably especially during the past two decades, there is still a need to increase understanding on the special characteristics of service innovation. In addition to studying innovation in service companies and industries, research has also recently focused more on services in innovation, as especially the significance of so-called knowledge intensive business services (KIBS) for the competitive edge of their clients, othercompanies, regions and even nations has been proved in several previous studies. This study focuses on studying technology-based KIBS firms, and technology andengineering consulting (TEC) sector in particular. These firms have multiple roles in innovation systems, and thus, there is also a need for in-depth studies that increase knowledge about the types and dimensions of service innovations as well as underlying mechanisms and procedures which make the innovations successful. The main aim of this study is to generate new knowledge in the fragmented research field of service innovation management by recognizing the different typesof innovations in TEC services and some of the enablers of and barriers to innovation capacity in the field, especially from the knowledge management perspective. The study also aims to shed light on some of the existing routines and new constructions needed for enhancing service innovation and knowledge processing activities in KIBS companies of the TEC sector. The main samples of data in this research include literature reviews and public data sources, and a qualitative research approach with exploratory case studies conducted with the help of the interviews at technology consulting companies in Singapore in 2006. These complement the qualitative interview data gathered previously in Finland during a larger research project in the years 2004-2005. The data is also supplemented by a survey conducted in Singapore. The respondents for the survey by Tan (2007) were technology consulting companies who operate in the Singapore region. The purpose ofthe quantitative part of the study was to validate and further examine specificaspects such as the influence of knowledge management activities on innovativeness and different types of service innovations, in which the technology consultancies are involved. Singapore is known as a South-east Asian knowledge hub and is thus a significant research area where several multinational knowledge-intensive service firms operate. Typically, the service innovations identified in the studied TEC firms were formed by several dimensions of innovations. In addition to technological aspects, innovations were, for instance, related to new client interfaces and service delivery processes. The main enablers of and barriers to innovation seem to be partly similar in Singaporean firms as compared to the earlier study of Finnish TEC firms. Empirical studies also brought forth the significance of various sources of knowledge and knowledge processing activities as themain driving forces of service innovation in technology-related KIBS firms. A framework was also developed to study the effect of knowledge processing capabilities as well as some moderators on the innovativeness of TEC firms. Especially efficient knowledge acquisition and environmental dynamism seem to influence the innovativeness of TEC firms positively. The results of the study also contributeto the present service innovation literature by focusing more on 'innovation within KIBs' rather than 'innovation through KIBS', which has been the typical viewpoint stressed in the previous literature. Additionally, the study provides several possibilities for further research.

A novel procedure for establishing clinching parameters for high strength steel sheet

The building industry has a particular interest in using clinching as a joining method for frame constructions of light-frame housing. Normally many clinch joints are required in joining of frames.In order to maximise the strength of the complete assembly, each clinch joint must be as sound as possible. Experimental testing is the main means of optimising a particular clinch joint. This includes shear strength testing and visual observation of joint cross-sections. The manufacturers of clinching equipment normally perform such experimental trials. Finite element analysis can also be used to optimise the tool geometry and the process parameter, X, which represents the thickness of the base of the joint. However, such procedures require dedicated software, a skilled operator, and test specimens in order to verify the finite element model. In addition, when using current technology several hours' computing time may be necessary. The objective of the study was to develop a simple calculation procedure for rapidly establishing an optimum value for the parameter X for a given tool combination. It should be possible to use the procedure on a daily basis, without stringent demands on the skill of the operator or the equipment. It is also desirable that the procedure would significantly decrease thenumber of shear strength tests required for verification. The experimental workinvolved tests in order to obtain an understanding of the behaviour of the sheets during clinching. The most notable observation concerned the stage of the process in which the upper sheet was initially bent, after which the deformation mechanism changed to shearing and elongation. The amount of deformation was measured relative to the original location of the upper sheet, and characterised as the C-measure. By understanding in detail the behaviour of the upper sheet, it waspossible to estimate a bending line function for the surface of the upper sheet. A procedure was developed, which makes it possible to estimate the process parameter X for each tool combination with a fixed die. The procedure is based on equating the volume of material on the punch side with the volume of the die. Detailed information concerning the behaviour of material on the punch side is required, assuming that the volume of die does not change during the process. The procedure was applied to shear strength testing of a sample material. The sample material was continuously hot-dip zinc-coated high-strength constructional steel,with a nominal thickness of 1.0 mm. The minimum Rp0.2 proof stress was 637 N/mm2. Such material has not yet been used extensively in light-frame housing, and little has been published on clinching of the material. The performance of the material is therefore of particular interest. Companies that use clinching on a daily basis stand to gain the greatest benefit from the procedure. By understanding the behaviour of sheets in different cases, it is possible to use data at an early stage for adjusting and optimising the process. In particular, the functionality of common tools can be increased since it is possible to characterise the complete range of existing tools. The study increases and broadens the amount ofbasic information concerning the clinching process. New approaches and points of view are presented and used for generating new knowledge.

Technology selection and group decision support systems: Case studies on supporting strategic technology selection processes

The objective of the dissertation is to increase understanding and knowledge in the field where group decision support system (GDSS) and technology selection research overlap in the strategic sense. The purpose is to develop pragmatic, unique and competent management practices and processes for strategic technology assessment and selection from the whole company's point of view. The combination of the GDSS and technology selection is approached from the points of view of the core competence concept, the lead user -method, and different technology types. In this research the aim is to find out how the GDSS contributes to the technology selection process, what aspects should be considered when selecting technologies to be developed or acquired, and what advantages and restrictions the GDSS has in the selection processes. These research objectives are discussed on the basis of experiences and findings in real life selection meetings. The research has been mainly carried outwith constructive, case study research methods. The study contributes novel ideas to the present knowledge and prior literature on the GDSS and technology selection arena. Academic and pragmatic research has been conducted in four areas: 1) the potential benefits of the group support system with the lead user -method,where the need assessment process is positioned as information gathering for the selection of wireless technology development projects; 2) integrated technology selection and core competencies management processes both in theory and in practice; 3) potential benefits of the group decision support system in the technology selection processes of different technology types; and 4) linkages between technology selection and R&D project selection in innovative product development networks. New type of knowledge and understanding has been created on the practical utilization of the GDSS in technology selection decisions. The study demonstrates that technology selection requires close cooperation between differentdepartments, functions, and strategic business units in order to gather the best knowledge for the decision making. The GDSS is proved to be an effective way to promote communication and co-operation between the selectors. The constructs developed in this study have been tested in many industry fields, for example in information and communication, forest, telecommunication, metal, software, and miscellaneous industries, as well as in non-profit organizations. The pragmatic results in these organizations are some of the most relevant proofs that confirm the scientific contribution of the study, according to the principles of the constructive research approach.

Maximizing Benefits in Information Technology Outsourcing

Information Technology (IT) outsourcing has traditionally been seen as a means to acquire newresources and competencies to perform standard tasks at lowered cost. This dissertationchallenges the thought that outsourcing should be limited to non-strategic systems andcomponents, and presents ways to maximize outsourcing enabled benefits while minimizingassociated risks. In this dissertation IT outsourcing is approached as an efficiency improvement and valuecreationprocess rather than a sourcing decision. The study focuses on when and how tooutsource information technology, and presents a new set of critical success factors foroutsourcing project management. In a case study it re-validates the theory-based propositionthat in certain cases and situations it is beneficial to partly outsource also strategic IT systems. The main contribution of this dissertation is the validation of proposal that in companies wherethe level of IT competency is high, managerial support established and planning processes welldefined,it is possible to safely outsource also business critical IT systems. A model describing the critical success factors in such cases is presented based on existing knowledge on the fieldand the results of empirical study. This model further highlights the essence of aligning IT andbusiness strategies, assuming long-term focus on partnering, and the overall target ofoutsourcing to add to the strengths of the company rather than eliminating weaknesses.

On the Reversed Brayton Cycle with High Speed Machinery

This work was carried out in the laboratory of Fluid Dynamics, at Lappeenranta University of Technology during the years 1991-1996. The research was a part of larger high speed technology development research. First, there was the idea of making high speed machinery applications with the Brayton cycle. There was a clear need to deepen theknowledge of the cycle itself and to make a new approach in the field of the research. Also, the removal of water from the humid air seemed very interesting. The goal of this work was to study methods of designing high speed machinery to the reversed Brayton cycle, from theoretical principles to practical applications. The reversed Brayton cycle can be employed as an air dryer, a heat pump or a refrigerating machine. In this research the use of humid air as a working fluid has an environmental advantage, as well. A new calculation method for the Braytoncycle is developed. In this method especially the expansion process in the turbine is important because of the condensation of the water vapour in the humid air. This physical phenomena can have significant effects on the level of performance of the application. Also, the influence of calculating the process with actual, achievable process equipment efficiencies is essential for the development of the future machinery. The above theoretical calculations are confirmed with two different laboratory prototypes. The high speed machinery concept allows one to build an application with only one rotating shaft including all the major parts: the high speed motor, the compressor and the turbine wheel. The use of oil free bearings and high rotational speed outlines give several advantages compared to conventional machineries: light weight, compact structure, safe operation andhigher efficiency at a large operational region. There are always problems whentheory is applied to practice. The calibrations of pressure, temperature and humidity probes were made with care but still measurable errors were not negligible. Several different separators were examined and in all cases the content of the separated water was not exact. Due to the compact sizes and structures of the prototypes, the process measurement was slightly difficult. The experimental results agree well with the theoretical calculations. These experiments prove the operation of the process and lay a ground for the further development. The results of this work give very promising possibilities for the design of new, commercially competitive applications that use high speed machinery and the reversed Brayton cycle.

Characteristics of Flowing Film

Työssä tutkittiin uutta teknologiaa pigmenttipäällystykseen. Tämä tekniikka on yleisesti tunnettua eräillä muilla teollisuudenaloilla. Kirjallisuustutkimuksessa on esitelty prosessia ja sen eri osatekijöitä sekä muilla aloilla tunnettuja prosessimuuttujia. Päällystyspastojen ja päällystettävien pintojen teoriaa on selvitetty uuden tekniikan ja pigmenttipäällystyksen valossa. Uuden tekniikan perusmekanismeja tutkittiin kokeellisessa osassa. Valuvan nestefilmin stabiilisuutta tutkittiin minimivirtauksen avulla. Stabiilisuustutkimuksen suorittamiseen käytettiin apuna Taguchi-matriisia DOE-ohjelmalla (Design of Experiments). Kokeiden perusteella minimivirtauksen kannalta päällystyspastalle edullisempi koostumus on kalsiumkarbonaatti- kuin kaoliinipasta. Sideaineella on pienempi osuus lateksia ja polyvinyylialkoholia parempi. Suurempi osuus pinta-aktiivista ainetta ja matala pastan kuiva-ainepitoisuus ovat suositeltuja. Tehokas ilmanpoisto päällystyspastasta on myös tärkeää lopullisen tuloksen kannalta. Koekoneella ajetuissa päällystyskokeissa havaittiin valuvan filmin ominaisuuksien tärkeys. Pienetkin kaasumäärät päällystyspastassa häiritsivät lopullisen päällysteen laatua. Päällystyspastan ilmanpoisto on avainasemassa erityisesti kun päällystetään suurella nopeudella pieniä päällystemääriä. Koeajoissa havaittiin kaikki kirjallisuudessa esitellyt rajoittavat tekijät. Kokeissa päällystettiin 400-1600 m/min nopeudella 5-20 g/m² päällystemääriä. Olosuhteet stabiilille nestefilmille vaativat edelleen kehitystä suurella nopeudella päällystettäessä. Päällysteen eroavaisuuksia verrattiin teräpäällystysmenetelmiin. Terä-päällystyksellä saadaan sileä mutta epätasaisesti peittävä pinta kun taas uuden tekniikan päällyste mukailee päällystettävän alustan topografiaa. Tasapaksun päällysteen etuna on hyvä peittävyys jo pienellä päällystemäärällä.

High Throughput Purification of Combinatorial Libraries by Preparative LC/MS

Viime vuosien nopea kehitys on kiihdyttänyt uusien lääkkeiden kehittämisprosessia. Kombinatorinen kemia on tehnyt mahdolliseksi syntetisoida suuria kokoelmia rakenteeltaan toisistaan poikkeavia molekyylejä, nk. kombinatorisia kirjastoja, biologista seulontaa varten. Siinä molekyylien rakenteeseen liittyvä aktiivisuus tutkitaan useilla erilaisilla biologisilla testeillä mahdollisten "osumien" löytämiseksi, joista osasta saatetaan myöhemmin kehittää uusia lääkeaineita. Jotta biologisten tutkimusten tulokset olisivat luotettavia, on syntetisoitujen komponenttien oltava mahdollisimman puhtaita. Tämän vuoksi tarvitaan HTP-puhdistusta korkealaatuisten komponenttien ja luotettavan biologisen tiedon takaamiseksi. Jatkuvasti kasvavat tuotantovaatimukset ovat johtaneet näiden puhdistustekniikoiden automatisointiin ja rinnakkaistamiseen. Preparatiivinen LC/MS soveltuu kombinatoristen kirjastojen nopeaan ja tehokkaaseen puhdistamiseen. Monet tekijät, esimerkiksi erotuskolonnin ominaisuudet sekä virtausgradientti, vaikuttavat preparatiivisen LC/MS puhdistusprosessin tehokkuuteen. Nämä parametrit on optimoitava parhaan tuloksen saamiseksi. Tässä työssä tutkittiin emäksisiä komponentteja erilaisissa virtausolosuhteissa. Menetelmä kombinatoristen kirjastojen puhtaustason määrittämiseksi LC/MS-puhdistuksen jälkeen optimoitiin ja määritettiin puhtaus joillekin komponenteille eri kirjastoista ennen puhdistusta.

High Performance Electrical Drive System for a Biomechanical Test and Rehabilitation Equipment

Suunniteltiin ja rakennettiin suoraa vääntömomenttisäätöä soveltava taajuudenmuuttajakäyttö oikosulkumoottorin ohjaukseen korvaamaan passiivinen jarrukäyttö. Laite on kuntoutuslaite, jolla tehdään lihasvoiman mittauksia ja voimaharjoituksia. Selvitettiin kaupallisten moottoreiden ja taajuudenmuuttajien suoritusominaisuuksia ja tämän perusteella valittiin käyttöön sopivat laitteet. Työssä esitetään kaksi oikosulkumoottorin ohjaustapaa: vektorisäätö ja suora vääntömomenttisäätö. Merkittävin osa tästä työstä käsittelee - tarkan turvallisuussuunnitelman lisäksi - kuntoutuslaitteen prototyypin komponentteja, kokoamista ja suoritustestien tuloksia.

The high-speed induction motor: calculating the effects of solid-rotor material on machine characteristics

A method for the analysis of high-speed solid-rotor induction motors in presented. The analysis is based on a new combination of the three dimensional linear method and the transfer matrix method. Both saturation and finite length effects are taken into account. The active region of the solid rotor is divided into saturated and unsaturated parts. The time dependence is assumed to be sinusoidal and phasor quantities are used in the solution. The method is applied to the calculation of smooth solid rotors manufactured of different materials. Six rotor materials are tested: three construction steels, pure iron, a cobaltiron alloy and an aluminium alloy. The results obtained by the method agree fairly well with the measurement quantities.

Gas-phase photocatalytic oxidation of volatile organic compounds

Substances emitted into the atmosphere by human activities in urban and industrial areas cause environmental problems such as air quality degradation, respiratory diseases, climate change, global warming, and stratospheric ozone depletion. Volatile organic compounds (VOCs) are major air pollutants, emitted largely by industry, transportation and households. Many VOCs are toxic, and some are considered to be carcinogenic, mutagenic, or teratogenic. A wide spectrum of VOCs is readily oxidized photocatalytically. Photocatalytic oxidation (PCO) over titanium dioxide may present a potential alternative to air treatment strategies currently in use, such as adsorption and thermal treatment, due to its advantageous activity under ambient conditions, although higher but still mild temperatures may also be applied. The objective of the present research was to disclose routes of chemical reactions, estimate the kinetics and the sensitivity of gas-phase PCO to reaction conditions in respect of air pollutants containing heteroatoms in their molecules. Deactivation of the photocatalyst and restoration of its activity was also taken under consideration to assess the practical possibility of the application of PCO to the treatment of air polluted with VOCs. UV-irradiated titanium dioxide was selected as a photocatalyst for its chemical inertness, non-toxic character and low cost. In the present work Degussa P25 TiO2 photocatalyst was mostly used. In transient studies platinized TiO2 was also studied. The experimental research into PCO of following VOCs was undertaken: - methyl tert-butyl ether (MTBE) as the basic oxygenated motor fuel additive and, thus, a major non-biodegradable pollutant of groundwater; - tert-butyl alcohol (TBA) as the primary product of MTBE hydrolysis and PCO; - ethyl mercaptan (ethanethiol) as one of the reduced sulphur pungent air pollutants in the pulp-and-paper industry; - methylamine (MA) and dimethylamine (DMA) as the amino compounds often emitted by various industries. The PCO of VOCs was studied using a continuous-flow mode. The PCO of MTBE and TBA was also studied by transient mode, in which carbon dioxide, water, and acetone were identified as the main gas-phase products. The volatile products of thermal catalytic oxidation (TCO) of MTBE included 2-methyl-1-propene (2-MP), carbon monoxide, carbon dioxide and water; TBA decomposed to 2-MP and water. Continuous PCO of 4 TBA proceeded faster in humid air than dry air. MTBE oxidation, however, was less sensitive to humidity. The TiO2 catalyst was stable during continuous PCO of MTBE and TBA above 373 K, but gradually lost activity below 373 K; the catalyst could be regenerated by UV irradiation in the absence of gas-phase VOCs. Sulphur dioxide, carbon monoxide, carbon dioxide and water were identified as ultimate products of PCO of ethanethiol. Acetic acid was identified as a photocatalytic oxidation by-product. The limits of ethanethiol concentration and temperature, at which the reactor performance was stable for indefinite time, were established. The apparent reaction kinetics appeared to be independent of the reaction temperature within the studied limits, 373 to 453 K. The catalyst was completely and irreversibly deactivated with ethanethiol TCO. Volatile PCO products of MA included ammonia, nitrogen dioxide, nitrous oxide, carbon dioxide and water. Formamide was observed among DMA PCO products together with others similar to the ones of MA. TCO for both substances resulted in the formation of ammonia, hydrogen cyanide, carbon monoxide, carbon dioxide and water. No deactivation of the photocatalyst during the multiple long-run experiments was observed at the concentrations and temperatures used in the study. PCO of MA was also studied in the aqueous phase. Maximum efficiency was achieved in an alkaline media, where MA exhibited high fugitivity. Two mechanisms of aqueous PCO – decomposition to formate and ammonia, and oxidation of organic nitrogen directly to nitrite - lead ultimately to carbon dioxide, water, ammonia and nitrate: formate and nitrite were observed as intermediates. A part of the ammonia formed in the reaction was oxidized to nitrite and nitrate. This finding helped in better understanding of the gasphase PCO pathways. The PCO kinetic data for VOCs fitted well to the monomolecular Langmuir- Hinshelwood (L-H) model, whereas TCO kinetic behaviour matched the first order process for volatile amines and the L-H model for others. It should be noted that both LH and the first order equations were only the data fit, not the real description of the reaction kinetics. The dependence of the kinetic constants on temperature was established in the form of an Arrhenius equation.