Lithostratigraphy and age of pre-Late Weichselian sediments in the Suupohja area, western Finland

Different types of laterally extensive sand- and gravel-dominated deposits, up to several tens of metres thick, were investigated in the Suupohja area of western Finland. The studied sediments were deposited in glacial, ice-marginal, glaciofluvial, sea or lake, littoral and terrestrial environments during several glacial-non-glacial cycles. Seventeen pre-Late Weichselian and three Late Weichselian/Holocene sedimentary units were identified. These were divided into ten formally and two informally defined formations that were together termed the Suupohja Group. Every unit are nevertheless not detectable throughout the study area. The informally defined “Karhukangas lower deposits” represent the lowest units in the Suupohja Group. The Karhukangas lower deposits with 5 till units, 3 glaciolacustrine/-marine units and 2 sand units, were interpreted as having been deposited during possibly four glacial-non-glacial cycles before the Late Pleistocene Subepoch (MIS 6 or earlier). The Kankalo Sand above the Karhukangas lower deposits comprises glaciofluvial and aeolian sands of Late Saalian, Eemian or Early Weichselian origin (MIS 6–MIS 5c). The Kariluoma Till above the Kankalo Sand was possibly deposited during the Late Saalian glacial advance, although an Early Weichselian origin is also possible. The Harrinkangas Formation, with glaciofluvial and quiet-water sediments, is interpreted as having been deposited during the Late Saalian and Eemian Stages (MIS 6–MIS 5e). The uppermost units in the deposits studied, the Kodesjärvi Formation (shore deposit), Isojoki Sand (aeolian), Rävåsen Formation (glaciofluvial), Vanhakylä Formation (shore line deposit), Dagsmark Till and Kauhajoki Till, were deposited during the Weichselian Stage (MIS 5d–MIS 2). In addition, Early Holocene (MIS 1) eskers without till cover were informally termed the “Holocene esker deposits”. The Lumikangas Formation represents gravelly shore deposits formed in the Holocene Epoch, when these areas last emerged from the sea. The first Weichselian ice expansion possibly reached the western part of Suupohja in the Early Weichselian Substage (MIS 5d?), but it did not expand further to the east. The second Weichselian glaciation of relatively short duration occupied the southern part of Finland in the later part of Middle Weichselian (MIS 3). Thus, the southern half of the country remained ice-free for the majority (~65–75%) of the Weichselian Stage. Instead, both humid temperate and periglacial conditions alternated. In the initial part of Middle Weichselian, this area was partly submerged, which indicates eastward expansion of the Scandinavian ice sheet(s), depressing the lithosphere. The exceptionally thick sediment cover, multiple lithofacies, relict landscape and preserved preglacially weathered bedrock are evidence of weak glacial erosion in the Suupohja area during the latest as well as earlier glaciations, making this area one of the key areas in Quaternary research.

The Impact of Neonatal Antibiotic Exposure on Atopic Sensitisation by the Age of 12 Months

Varhaislapsuuden antibioottialtistuksen vaikutus atooppiseen herkistymiseen 12 kuukauden ikään mennessä Bakteerien vaikutus terveyteen on merkittävä: ne ovat toisaalta hengenvaarallisten infektioiden aiheuttajia, mutta samanaikaisesti niiden läsnäolo on välttämätöntä terveen immuunipuolustuksen kehittymiseksi. Ensimmäisen elinvuoden aikana suoliston bakteerikanta on altis ulkoisten tekijöiden vaikutuksille. Varhaislapsuuden antibioottihoidolla voi olla tuhoisat seuraukset eri bakteerilajien suhteille, ja sen tiedetään altistavan erilaisille immuunivälitteisille sairauksille, kuten atopialle. Ei ole kuitenkaan selvitetty, onko tämä vaikutus johtunut käynnissä olevan infektion aiheuttamista muutoksista kehittyvään immuunijärjestelmään vai onko siihen ollut syynä infektioon aloitettu antibioottihoito. Tässä tutkimuksessa selvitettiin eroja kahden, varhaista antibioottihoitoa saaneen ryhmän välillä ja päätetapahtumaksi katsottiin myöhemmin lapsuudessa ilmenevä atopiataipumus. Toinen ryhmä sai antibioottihoitoa kliinisesti todistettuun bakteeri-infektioon (varhaiseen sepsikseen). Toinen ryhmä taas sai antibioottihoidon pelkästään infektioepäilyyn eli ns. empiirisen hoidon, joka lopetettiin alle viiden vuorokauden kuluessa kun katsottiin, ettei oireiden taustalla ollutkaan bakteeri-infektiota. Mukana vertailussa oli lisäksi ryhmä, joka ei saanut lainkaan varhaista antibioottihoitoa. Antibioottihoidon pitkäaikaisvaikutusta arvioitiin ihon prick-testillä, joka kertoo atopiaan liittyvästä IgE-välitteisestä herkistymisestä. Varhaisella antibioottihoidolla tarkoitetaan tässä alle 72 tunnin sisällä syntymästä alkanutta hoitoa G-penisilliinin ja gentamysiinin yhdistelmällä. Tutkimuksen aineisto koostui 755 vastasyntyneen lapsen seurantadatasta, joka saatiin neljän käynnissä olevan allergian ehkäisytutkimuksen aineistosta. Tutkimuksen mukaanottokriteereinä pidettiin sitä, että saatavilla oli tiedot sekä mahdollisen antibioottialtistuksen kestosta että ihon prick-testituloksesta joko 6 tai 12 kuukauden iässä. Tulokset analysoitiin logistisella regressioanalyysillä huomioiden mahdolliset sekoittavat tekijät: äidin allergia, ennenaikaisuus, tutkimusprobiootti, imetyksen kesto, äidin raskauden aikainen tupakointi ja synnytystapa. Potilasryhmässä, joka sai antibioottihoitoa ilman samanaikaista infektiota, nähtiin tilastollisesti merkittävästi vähemmän positiivisia prick-testituloksia verrattuna lapsiin, jotka eivät altistuneet antibiooteille. Tulos on merkittävä, sillä se osoittaa, että varhaisella antibioottihoidolla on kauaskantoisia vaikutuksia kehittyvään immuunijärjestelmään.

MARKETING COMMUNICATIONS IN B2B COMPANIES – The Roles of Marketing Communication Tools in the Digital Age

Marketing communications has gone through significant changes during the last decades and new online tools have been leading this change for the last decade. Now, in the digital age, if wanting to be successful companies need to experiment new things and seize the opportunities online provides and adapt to the new environment. However, during this time the marketing communication mix and the meanings given to the various components of it have not changed dramatically, and personal selling, direct marketing, sales promotion, advertising and public relations activities are still regarded as important tools in the marketing communications mix. The purpose of this study was to examine business-to-business marketing communications and the tools used by companies in their marketing communications efforts in the digital age and in a global environment. The research questions dealt with the marketing communication tools and their roles as well as the role of online marketing communication and the way it has shaped the field of b2b marketing communications. In order to answer these questions, qualitative approach was chosen and the data was collected by theme interviews with six representatives of Finnish global companies from the b2b sector being interviewed. The theoretical framework covers the general field of b2b marketing communications and its main elements. The online environment as well as the concept of a global marketplace and integrated approach to marketing communication activities is also discussed. The theory was supported by the interviews regarding the activities and roles of the marketing communication tools and both theory as well as the interviews found personal selling to be a vital tool. However, the importance of online has grown and online marketing activities have risen right next to personal selling. The use of analytics and marketing automation was found to be of great interest in the interviews and they were seen as a growing domain in b2b marketing communications. The importance of targeted and personalised messages from relevant medias was a repeating theme as was the customer-centric approach in marketing communication activities. Also, offline and online tools and channels were seen as something that should be treated together as an entity rather than as separate activities. Relevant content created according to the needs of the customer with the gathered data from analytics were seen as the future of b2b marketing communications. Online has added its input to the more traditionally perceived tools and they are executed within the framework of the digital age. Nevertheless, even though online has increased its presence in the b2b marketing communications mix, the more traditionally perceived marketing communication tools, especially personal selling, have not lost their meaning or place in the b2b marketing communication mix.

Modelling Cutting States in Rough Turning of 34CrNiMo6 Steel

Rough turning is an important form of manufacturing cylinder-symmetric parts. Thus far, increasing the level of automation in rough turning has included process monitoring methods or adaptive turning control methods that aim to keep the process conditions constant. However, in order to improve process safety, quality and efficiency, an adaptive turning control should be transformed into an intelligent machining system optimizing cutting values to match process conditions or to actively seek to improve process conditions. In this study, primary and secondary chatter and chip formation are studied to understand how to measure the effect of these phenomena to the process conditions and how to avoid undesired cutting conditions. The concept of cutting state is used to address the combination of these phenomena and the current use of the power capacity of the lathe. The measures to the phenomena are not developed based on physical measures, but instead, the severity of the measures is modelled against expert opinion. Based on the concept of cutting state, an expert system style fuzzy control system capable of optimizing the cutting process was created. Important aspects of the system include the capability to adapt to several cutting phenomena appearing at once, even if the said phenomena would potentially require conflicting control action.

Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Marks of Fire, Value and Faith. Swords with Ferrous Inlays in Finland during the Late Iron Age (ca. 700–1200 AD)

This study explores swords with ferrous inlays found in Finland and dating from the late Iron Age, ca. 700–1200 AD. These swords reflect profound changes not only in styles and fashion but also in the technology of hilts and blades. This study explores how many of these kinds of swords are known from Finland, how they were made and where, what their status was in Late Iron Age Finland, and where the Finnish finds stand in accordance with other areas of Europe. The various methods included measuring of the finds and statistics. The main method of revealing the inlaid marks was radiography due to its non-destructive nature. In cases where inlays were visible without radiography, their details were inspected via microscopy. To study the materials and manufacture of inlaid swords, a sample of them was metallographically analysed to determine the forging technologies and nature of used materials. Furthermore, the manufacture was also studied with experimental approaches. As a result, a catalogue of 151 swords with ferrous inlays was created. This number is relatively high compared with other European countries, although systematic studies have been conducted in only some countries. The inlaid motifs were classified into five distinct categories to help the classification. To summarize, almost every documented inlaid sword was unique in some respect including measurements, inlaid motifs and materials of blades and inlays. Technological variation was also present, some blades being poorer and some of higher quality in spite of the inlaid motifs. Misspelt inscriptions as well as letter-like marks were common in Finland and also in Scandinavia. Furthermore, the provenance of iron and steel used in some blades hints at Scandinavian ores. The above observations, along with the experimental results indicating the existence of multiple alternative techniques of inlaying, suggest that these swords were manufactured locally in Scandinavia, most likely in imitation of Continental European models. Inlaid swords were valued partly for their assumed functionality in combat, as evidenced by damage on some examined blades, or they were valued for their inlays, which could have had fashionable or symbolical meanings bound to local beliefs.

Prediction of neurodevelopment and neuromotor trajectories in very preterm born children up to 11 years of age: PIPARI Study

Very preterm birth is a risk for brain injury and abnormal neurodevelopment. While the incidence of cerebral palsy has decreased due to advances in perinatal and neonatal care, the rate of less severe neuromotor problems continues to be high in very prematurely born children. Neonatal brain imaging can aid in identifying children for closer follow-up and in providing parents information on developmental risks. This thesis aimed to study the predictive value of structural brain magnetic resonance imaging (MRI) at term age, serial neonatal cranial ultrasound (cUS), and structured neurological examinations during the longitudinal follow-up for the neurodevelopment of very preterm born children up to 11 years of age as a part of the PIPARI Study (The Development and Functioning of Very Low Birth Weight Infants from Infancy to School Age). A further aim was to describe the associations between regional brain volumes and long-term neuromotor profile. The prospective follow-up comprised of the assessment of neurosensory development at 2 years of corrected age, cognitive development at 5 years of chronological age, and neuromotor development at 11 years of age. Neonatal brain imaging and structured neurological examinations predicted neurodevelopment at all age-points. The combination of neurological examination and brain MRI or cUS improved the predictive value of neonatal brain imaging alone. Decreased brain volumes associated with neuromotor performance. At the age of 11 years, the majority of the very preterm born children had age-appropriate neuromotor development and after-school sporting activities. Long-term clinical follow-up is recommended at least for all very preterm infants with major brain pathologies.