Minimizing Conducted RF-Emissions in Switch Mode Power Supplies Using Spread-Spectrum Techniques

Switching power supplies are usually implemented with a control circuitry that uses constant clock frequency turning the power semiconductor switches on and off. A drawback of this customary operating principle is that the switching frequency and harmonic frequencies are present in both the conducted and radiated EMI spectrum of the power converter. Various variable-frequency techniques have been introduced during the last decade to overcome the EMC problem. The main objective of this study was to compare the EMI and steady-state performance of a switch mode power supply with different spread-spectrum/variable-frequency methods. Another goal was to find out suitable tools for the variable-frequency EMI analysis. This thesis can be divided into three main parts: Firstly, some aspects of spectral estimation and measurement are presented. Secondly, selected spread spectrum generation techniques are presented with simulations and background information. Finally, simulations and prototype measurements from the EMC and the steady-state performance are carried out in the last part of this work. Combination of the autocorrelation function, the Welch spectrum estimate and the spectrogram were used as a substitute for ordinary Fourier methods in the EMC analysis. It was also shown that the switching function can be used in preliminary EMC analysis of a SMPS and the spectrum and autocorrelation sequence of a switching function correlates with the final EMI spectrum. This work is based on numerous simulations and measurements made with the prototype. All these simulations and measurements are made with the boost DC/DC converter. Four different variable-frequency modulation techniques in six different configurations were analyzed and the EMI performance was compared to the constant frequency operation. Output voltage and input current waveforms were also analyzed in time domain to see the effect of the spread spectrum operation on these quantities. According to the results presented in this work, spread spectrum modulation can be utilized in power converter for EMI mitigation. The results from steady-state voltage measurements show, that the variable-frequency operation of the SMPS has effect on the voltage ripple, but the ripple measured from the prototype is still acceptable in some applications. Both current and voltage ripple can be controlled with proper main circuit and controller design.

Spin Polarization and Normal Reflection at Nanoscale Point Contacts

This thesis presents point-contact measurements between superconductors (Nb, Ta, Sn,Al, Zn) and ferromagnets (Co, Fe, Ni) as well as non-magnetic metals (Ag, Au, Cu, Pt).The point contacts were fabricated using the shear method. The differential resistanceof the contacts was measured either in liquid He at 4.2 K or in vacuum in a dilutionrefrigerator at varying temperature down to 0.1 K. The contact properties were investigatedas function of size and temperature. The measured Andreev-reflection spectrawere analysed in the framework of the BTK model – a three parameter model that describescurrent transport across a superconductor - normal conductor interface. Theoriginal BTK model was modified to include the effects of spin polarization or finitelifetime of the Cooper pairs. Our polarization values for the ferromagnets at 4.2 K agree with the literature data, but the analysis was ambiguous because the experimental spectra both with ferromagnets and non-magnets could be described equally well either with spin polarization or finite lifetime effects in the BTK model. With the polarization model the Z parametervaries from almost 0 to 0.8 while the lifetime model produces Z values close to 0.5. Measurements at lower temperatures partly lift this ambiguity because the magnitude of thermal broadening is small enough to separate lifetime broadening from the polarization. The reduced magnitude of the superconducting anomalies for Zn-Fe contacts required an additional modification of the BTK model which was implemented as a scaling factor. Adding this parameter led to reduced polarization values. However, reliable data is difficult to obtain because different parameter sets produce almost identical spectra.

Nanoparticle-Assisted Immunoassays for Point-of-Care Testing - With Specific Interest in Minimally Interference-Prone Assays for Cardiac Troponin I

Cardiac troponins (cTn) I and T are the current golden standard biochemical markers in the diagnosis and risk stratification of patients with suspected acute coronary syndrome. During the past few years, novel assays capable of detecting cTn‐concentrations in >50% of apparently healthy individuals have become readily available. With the emerging of these high sensitivity cTn assays, reductions in the assay specificity have caused elevations in the measured cTn levels that do not correlate with the clinical picture of the patient. The increased assay sensitivity may reveal that various analytical interference mechanisms exist. This doctoral thesis focused on developing nanoparticle‐assisted immunometric assays that could possibly be applied to an automated point‐of‐care system. The main objective was to develop minimally interference‐prone assays for cTnI by employing recombinant antibody fragments. Fast 5‐ and 15‐minute assays for cTnI and D‐dimer, a degradation product of fibrin, based on intrinsically fluorescent nanoparticles were introduced, thus highlighting the versatility of nanoparticles as universally applicable labels. The utilization of antibody fragments in different versions of the developed cTnI‐assay enabled decreases in the used antibody amounts without sacrificing assay sensitivity. In addition, the utilization of recombinant antibody fragments was shown to significantly decrease the measured cTnI concentrations in an apparently healthy population, as well as in samples containing known amounts of potentially interfering factors: triglycerides, bilirubin, rheumatoid factors, or human anti‐mouse antibodies. When determining the specificity of four commercially available antibodies for cTnI, two out of the four cross‐reacted with skeletal troponin I, but caused crossreactivity issues in patient samples only when paired together. In conclusion, the results of this thesis emphasize the importance of careful antibody selection when developing cTnI assays. The results with different recombinant antibody fragments suggest that the utilization of antibody fragments should strongly be encouraged in the immunoassay field, especially with analytes such as cTnI that require highly sensitive assay approaches.

From Unspecific Quenching to Specific Signaling: Functional GTPase Assays Utilizing Quenching Resonance Energy Transfer (QRET) Technology

The aim of the work presented in this study was to demonstrate the wide applicability of a single-label quenching resonance energy transfer (QRET) assay based on time-resolved lanthanide luminescence. QRET technology is proximity dependent method utilizing weak and unspecific interaction between soluble quencher molecule and lanthanide chelate. The interaction between quencher and chelate is lost when the ligand binds to its target molecule. The properties of QRET technology are especially useful in high throughput screening (HTS) assays. At the beginning of this study, only end-point type QRET technology was available. To enable efficient study of enzymatic reactions, the QRET technology was further developed to enable measurement of reaction kinetics. This was performed using proteindeoxyribonuclei acid (DNA) interaction as a first tool to monitor reaction kinetics. Later, the QRET was used to study nucleotide exchange reaction kinetics and mutation induced effects to the small GTPase activity. Small GTPases act as a molecular switch shifting between active GTP bound and inactive GDP bound conformation. The possibility of monitoring reaction kinetics using the QRET technology was evaluated using two homogeneous assays: a direct growth factor detection assay and a nucleotide exchange monitoring assay with small GTPases. To complete the list, a heterogeneous assay for monitoring GTP hydrolysis using small GTPases, was developed. All these small GTPase assays could be performed using nanomolar protein concentrations without GTPase pretreatment. The results from these studies demonstrated that QRET technology can be used to monitor reaction kinetics and further enable the possibility to use the same method for screening.

The effect of focal point parameters in fiber laser welding of structural steel

In this thesis the effect of focal point parameters in fiber laser welding of structural steel is studied. The goal is to establish relations between laser power, focal point diameter and focal point position with the resulting quality, weld-bead geometry and hardness of the welds. In the laboratory experiments, AB AH36 shipbuilding steel was welded in an I-butt joint configuration using IPG YLS-10000 continuous wave fiber laser. The quality of the welds produced were evaluated based on standard SFS-EN ISO 13919-1. The weld-bead geometry was defined from the weld cross-sections and Vickers hardness test was used to measure hardness's from the middle of the cross-sections. It was shown that all the studied focal point parameters have an effect on the quality, weld-bead geometry and hardness of the welds produced.

Modelling Energy Consumption of a Switch using Fuzzy-Rule Classifier

The energy consumption of IT equipments is becoming an issue of increasing importance. In particular, network equipments such as routers and switches are major contributors to the energy consumption of internet. Therefore it is important to understand how the relationship between input parameters such as bandwidth, number of active ports, traffic-load, hibernation-mode and their impact on energy consumption of a switch. In this paper, the energy consumption of a switch is analyzed in extensive experiments. A fuzzy rule-based model of energy consumption of a switch is proposed based on the result of experiments. The model can be used to predict the energy saving when deploying new switches by controlling the parameters to achieve desired energy consumption and subsequent performance. Furthermore, the model can also be used for further researches on energy saving techniques such as energy-efficient routing protocol, dynamic link shutdown, etc.

Analysing the power consumption behaviour of Ethernet switch using Design of Experiment

At present, one of the main concerns of green network is to minimize the power consumption of network infrastructure. Surveys show that, the highest amount of power is consumed by the network devices during its runtime. However to control this power consumption it is important to know which factors has highest impact on this matter. This paper is focused on the measurement and modeling the power consumption of an Ethernet switch during its runtime considering various types of input parameters with all possible combinations. For the experiment, three input parameters are chosen. They are bandwidth, link load and number of connections. The output to be measured is the power consumption of the Ethernet switch. Due to the uncertain power consuming pattern of the Ethernet switch a fully-comprehensive experimental evaluation would require an unfeasible and cumbersome experimental phase. Because of that, design of experiment (DoE) method has been applied to obtain adequate information on the effects of each input parameters on the power consumption. The whole work consists of three parts. In the first part a test bed is planned with input parameters and the power consumption of the switch is measured. The second part is about generating a mathematical model with the help of design of experiment tools. This model can be used for measuring precise power consumption in different scenario and also pinpoint the parameters with higher influence in power consumption. And in the last part, the mathematical model is evaluated by comparing with the experimental values.

Spectrally Tuned Lanthanide Photoluminescence for Point-of-Care Testing

Point-of-care (POC) –diagnostics is a field with rapidly growing market share. As these applications become more widely used, there is an increasing pressure to improve their performance to match the one of a central laboratory tests. Lanthanide luminescence has been widely utilized in diagnostics because of the numerous advantages gained by the utilization of time-resolved or anti-Stokes detection. So far the use of lanthanide labels in POC has been scarce due to limitations set by the instrumentation required for their detection and the shortcomings, e.g. low brightness, of these labels. Along with the advances in the research of lanthanide luminescence, and in the field of semiconductors, these materials are becoming a feasible alternative for the signal generation also in the future POC assays. The aim of this thesis was to explore ways of utilizing time-resolved detection or anti-Stokes detection in POC applications. The long-lived fluorescence for the time-resolved measurement can be produced with lanthanide chelates. The ultraviolet (UV) excitation required by these chelates is cumbersome to produce with POC compatible fluorescence readers. In this thesis the use of a novel light-harvesting ligand was studied. This molecule can be used to excite Eu(III)-ions at wavelengths extending up to visible part of the spectrum. An enhancement solution based on this ligand showed a good performance in a proof-of-concept -bioaffinity assay and produced a bright signal upon 365 nm excitation thanks to the high molar absorptivity of the chelate. These features are crucial when developing miniaturized readers for the time-resolved detection of fluorescence. Upconverting phosphors (UCPs) were studied as an internal light source in glucose-sensing dry chemistry test strips and ways of utilizing their various emission wavelengths and near-infrared excitation were explored. The use of nanosized NaYF :Yb3+,Tm3+-particles enabled the replacement of an external UV-light source with a NIR-laser and gave an additional degree of freedom in the optical setup of the detector instrument. The new method enabled a blood glucose measurement with results comparable to a current standard method of measuring reflectance. Microsized visible emitting UCPs were used in a similar manner, but with a broad absorbing indicator compound filtering the excitation and emission wavelengths of the UCP. This approach resulted in a novel way of benefitting from the non-linear relationship between the excitation power and emission intensity of the UCPs, and enabled the amplification of the signal response from the indicator dye.

The role of import intermediary companies in the Russian imports from the EU A case study of a Russian industrial company’s point of view on import intermediaries

The literature on agency suggests different implications for the use of export intermediaries. However, only few studies provide a view on import intermediaries. This thesis tries for its part to fill this research gap by studying the import intermediaries in the EU–Russia trade from a Russian industrial company’s point of view. The aim is to describe import intermediation and explain the need for import intermediary companies in the EU–Russia trade. The theoretical framework of this thesis originates from an article by Peng and York (2001), in which they study the performance of export intermediaries. This thesis applies resource-based theory, transaction cost theory and agency cost theory, following the idea of Peng and York. The resource-based theory approach is utilised for describing an ideal import intermediary company, and transaction cost theory provides a basis for understanding the benefits of using the services of import intermediary companies, while agency cost theory is applied in order to understand the risks the Russian industrial company faces when it decides to use the services of import intermediaries. The study is performed in the form of a case interview with a representative of a major Russian metallurgy company. The results of the study suggest that an ideal intermediary has the skills required specifically for the imports process, in order to save time and money of the principal company. The intermediary company helps reducing the amount of time the managers and the staff of the principal company use to make imports possible, thus reducing the salary costs and providing the possibility to concentrate on the company’s core competencies. The benefits of using the services of import intermediary companies are the reduced transaction costs, especially salary costs that are minimised because of the effectiveness and specialisation of import intermediaries. Intermediaries are specialised in the imports process and thus need less time and resources to organise the imports. They also help to reduce the fixed salary costs, because their services can be used only when needed. The risks of being misled by intermediaries are minimised by the competition on the import intermediary market. In case an intermediary attempts fraud, it gets replaced by its rival.

Biomarkkerit sepsiksen diagnostiikassa sekä Kvantitatiivisen prokalsitoniini-immunomäärityksen pystyttäminen ja optimointi point-of-care-ympäristöön

Termiä sepsis käytetään infektion aiheuttamasta yleisestä tulehdusreaktio-oireyhtymästä. Biokemiallinen merkkiaine eli biomarkkeri on aine, joka objektiivisesti mitattuna ja arvioituna toimii indikaattorina erottaen toisistaan normaalit biologiset prosessit ja patogeeniset prosessit. Lisäksi biomarkkeri saattaa osoittaa farmakologisen vasteen lääkehoidolle. Tutkielman kirjallisessa osassa on esitelty ja verrattu toisiinsa jo kliinisessä käytössä olevia sekä lupaavia, vielä tutkimusvaiheessa olevia, sepsiksen biomerkkiaineita. Lisäksi tutkielmassa on tarkasteltu sepsiksen todentamisen, tunnistamisen ja hoidon tulevaisuudennäkymiä. Prokalsitoniini (PCT) on eräs jo kliinisessä käytössä oleva sepsiksen biomerkkiaine. Tutkielman kokeellisessa osassa pystytettiin teho-osastoille suunnattu pikatesti PCT:n mittaamiseen aikaerotteista fluoresenssiteknologiaa hyödyntävälle AQT-järjestelmälle (DHR Finland Oy, Innotrac Diagnostics, Suomi). Järjestelmä mittaa 20–30 minuutissa biomerkkiainepitoisuuden. Tavoitteena oli löytää sopiva vasta-ainepari ja pystyttää kaksipuoleinen immunomääritys, jonka analyyttinen herkkyys on alle 0,02 ng/ml:ssa. Työssä tutkittiin biotinyloidun kokonaisen vasta-aineen ja paikkaspesifisesti biotinyloidun antigeenia sitovan fragmentin (engl. fragment antigen binding, Fab) toimivuutta sitojamolekyylinä. Lisäksi työssä verrattiin kahden eri leimamolekyylin, 9 hampaisen europiumkelaatin sekä Innotracissa kehitetyn tähtikelaatin, toimivuutta PCT-immunomäärityksessä. Vasta-aineiden mahdolliset ristireaktiot testattiin ja määritystä testattiin alustavasti eri näytematriiseissa. Työssä löydettiin 5 vasta-aineparia, joiden analyyttinen herkkyys oli alle 0,02 ng/ml:ssa. Aiemmin testattuja vasta-ainepareja parempi analyyttinen herkkyys johtui todennäköisesti yhden uuden leimavasta-aineen paremmasta affiniteetistä. Tähtikelaatilla leimatulla vasta-aineella analyyttinen herkkyys parani lähes viisinkertaisesti, kun sitä verrattiin 9-hampaisella euroopiumkelaatilla leimatun vasta-aineen määritykseen. Havaittiin myös, että Fab-fragmentilla mitattiin määrityksissä lähes kaksi kertaa suuremmat signaali-taustasuhteet, kun sitä verrattiin kokonaiseen vasta-aineeseen, tietyllä vasta-aineparilla. Tämä johtui luultavasti steeristen esteiden vähenemisestä. Näytematriisilla ei todettu olevan vaikutusta määritykseen, eikä ristireaktioita havaittu. Kehitetyn määrityksen suoriutumista verrattiin markkinoilla olevaan BRAHMS AG:n (Saksa) PCT-määritykseen käyttäen potilasnäytteitä. Korrelaatiokertoimet potilasnäytevertailuissa olivat 0,965–0,989 ja näytteiden mitatuissa pitoisuuksissa oli tasoero.

The role of import intermediary companies in the Russian imports from the EU A case study of a Russian industrial company’s point of view on import intermediaries

The literature on agency suggests different implications for the use of export intermediaries. However, only few studies provide a view on import intermediaries. This thesis tries for its part to fill this research gap by studying the import intermediaries in the EU–Russia trade from a Russian industrial company’s point of view. The aim is to describe import intermediation and explain the need for import intermediary companies in the EU–Russia trade. The theoretical framework of this thesis originates from an article by Peng and York (2001), in which they study the performance of export intermediaries. This thesis applies resource-based theory, transaction cost theory and agency cost theory, following the idea of Peng and York. The resource-based theory approach is utilised for describing an ideal import intermediary company, and transaction cost theory provides a basis for understanding the benefits of using the services of import intermediary companies, while agency cost theory is applied in order to understand the risks the Russian industrial company faces when it decides to use the services of import intermediaries. The study is performed in the form of a case interview with a representative of a major Russian metallurgy company. The results of the study suggest that an ideal intermediary has the skills required specifically for the imports process, in order to save time and money of the principal company. The intermediary company helps reducing the amount of time the managers and the staff of the principal company use to make imports possible, thus reducing the salary costs and providing the possibility to concentrate on the company’s core competencies. The benefits of using the services of import intermediary companies are the reduced transaction costs, especially salary costs that are minimised because of the effectiveness and specialisation of import intermediaries. Intermediaries are specialised in the imports process and thus need less time and resources to organise the imports. They also help to reduce the fixed salary costs, because their services can be used only when needed. The risks of being misled by intermediaries are minimised by the competition on the import intermediary market. In case an intermediary attempts fraud, it gets replaced by its rival.

ATTITUDES TOWARD RUSSIAN CUSTOMERS IN THE FINNISH RETAIL TRADE SECTOR – A salesperson’s point of view

The amount of Russian tourists in Finland has increased significantly in the past years. The impact of Russian tourism to the Finnish retail trade sector is enormous, since Russian tourists often spend a lot of money particularly on shopping. Shopping tourism is mainly focused in the near border cities, such as Imatra and Lappeenranta, and in addition in Helsinki metropolitan area. The purpose of this study is to map the attitudes and perceptions of the sales personnel who are working in the Finnish retail trade sector towards Russian customers and to discover which elements affect these attitudes. The theories in this study are based on cultural elements and elements related to sales behavior and performance. Cultural differences between Finland and Russia, cultural distance and cultural intelligence form the cultural aspect of this study. Customer orientation vs. sales orientation (SOCO), adaptive selling, selling skills and job competency, salesperson’s affect and empathy toward customers, and job autonomy form the elements concerning sales behavior and performance. Furthermore, the attitude – behavior link, based on social psychology is addressed. A survey was conducted in two retail trade chains operating in Finland. These retail companies have stores and department stores in different geographical areas in Finland and the survey was conducted in altogether 19 cities. In addition to the theories that were discussed, two expert interviews were conducted in order to get a deeper understanding of the phenomenon at hand. Moreover the interviews helped in the formulation of the hypotheses and the questionnaire design. The questionnaires were sent directly to the stores, where they were placed so that they were available for the sales personnel. Altogether 487 usable responses were collected. The returned questionnaires were analyzed with IBM SPSS 21 statistics program. The results of this study indicated that the attitudes toward Russian customers are more negative compared to other foreign customers. However, the respondents’ attitudes toward and perceptions of Russian customers varied a lot. From the background variables age, education level, length of employment in current workplace, and length of experience in customer service had an effect on the attitudes of the respondents. In addition, the perceptions of Russian customers were more positive in the Eastern Finland compared to Helsinki metropolitan area. The cultural elements; cultural knowledge, cultural distance and cultural intelligence all affected the attitudes of the respondents. From the elements related to sales behavior and performance customer orientation, salesperson’s affect and empathy toward customers, and perceived job autonomy had an effect on the attitudes