Comparing simulation methods for modelling the errors of stand inventory data

Abstract

Modelling of vegetative filter strips in catchment scale erosin control

Selostus: Valuma-aluetason mallisovellus suojakaistojen käytöstä eroosion torjunnassa

Objectives and motivations of small-scale forest owners : theoretical modelling and qualitative assessment

Abstract

Stand dynamics modelling approaches for multicohort management of eastern Canadian boreal forests

Abstract

Modelling variation of needle density of Scots pine at high latitudes

[Abstract]

Modelling the effect of temperature on height increment of Scots pine at high latitudes

Abstract

Linear prediction application for modelling the relationships between a large number of stand characteristics of Norway spruce stands

Abstract

Impingement jet cooling of end windings in a high-speed electric machine

The rotational speed of high-speed electric machines is over 15 000 rpm. These machines are compact in size when compared to the power rate. As a consequence, the heat fluxes are at a high level and the adequacy of cooling becomes an important design criterion. In the high-speed machines, the air gap between the stator and rotor is a narrow flow channel. The cooling air is produced with a fan and the flow is then directed to the air gap. The flow in the gap does not provide sufficient cooling for the stator end windings, and therefore additional cooling is required. This study investigates the heat transfer and flow fields around the coil end windings when cooling jets are used. As a result, an innovative and new assembly is introduced for the cooling jets, with the benefits of a reduced amount of hot spots, a lower pressure drop, and hence a lower power need for the cooling fan. The gained information can also be applied to improve the cooling of electric machines through geometry modifications. The objective of the research is to determine the locations of the hot spots and to find out induced pressure losses with different jet alternatives. Several possibilities to arrange the extra cooling are considered. In the suggested approach cooling is provided by using a row of air jets. The air jets have three main tasks: to cool the coils effectively by direct impingement jets, to increase and cool down the flow that enters the coil end space through the air gap, and to ensure the correct distribution of the flow by forming an air curtain with additional jets. One important aim of this study is the arrangement of cooling jets in such manner that hot spots can be avoided to wide extent. This enables higher power density in high-speed motors. This cooling system can also be applied to the ordinary electric machines when efficient cooling is needed. The numerical calculations have been performed using a commercial Computational Fluid Dynamics software. Two geometries have been generated: cylindrical for the studied machine and Cartesian for the experimental model. The main parameters include the positions, arrangements and number of jets, the jet diameters, and the jet velocities. The investigated cases have been tested with two widely used turbulence models and using a computational grid of over 500 000 cells. The experimental tests have been made by using a simplified model for the end winding space with cooling jets. In the experiments, an emphasis has been given to flow visualisation. The computational analysis shows good agreement with the experimental results. Modelling of the cooling jet arrangement enables also a better understanding of the complex system of heat transfer at end winding space.

Computational and Experimental Analysis of Flow Field in the Diffusers of Centrifugal Compressors

Centrifugal compressors are widely used for example in process industry, oil and gas industry, in small gas turbines and turbochargers. In order to achieve lower consumption of energy and operation costs the efficiency of the compressor needs to be improve. In the present work different pinches and low solidity vaned diffusers were utilized in order to improve the efficiency of a medium size centrifugal compressor. In this study, pinch means the decrement of the diffuser flow passage height. First different geometries were analyzed using computational fluid dynamics. The flow solver Finflo was used to solve the flow field. Finflo is a Navier-Stokes solver. The solver is capable to solve compressible, incompressible, steady and unsteady flow fields. Chien's k-e turbulence model was used. One of the numerically investigated pinched diffuser and one low solidity vaned diffuser were studied experimentally. The overall performance of the compressor and the static pressure distribution before and after the diffuser were measured. The flow entering and leaving the diffuser was measured using a three-hole Cobra-probe and Kiel-probes. The pinch and the low solidity vaned diffuser increased the efficiency of the compressor. Highest isentropic efficiency increment obtained was 3\% of the design isentropic efficiency of the original geometry. It was noticed in the numerical results that the pinch made to the hub and the shroud wall was most beneficial to the operation of the compressor. Also the pinch made to the hub was better than the pinchmade to the shroud. The pinch did not affect the operation range of the compressor, but the low solidity vaned diffuser slightly decreased the operation range.The unsteady phenomena in the vaneless diffuser were studied experimentally andnumerically. The unsteady static pressure was measured at the diffuser inlet and outlet, and time-accurate numerical simulation was conducted. The unsteady static pressure showed that most of the pressure variations lay at the passing frequency of every second blade. The pressure variations did not vanish in the diffuser and were visible at the diffuser outlet. However, the amplitude of the pressure variations decreased in the diffuser. The time-accurate calculations showed quite a good agreement with the measured data. Agreement was very good at the design operation point, even though the computational grid was not dense enough inthe volute and in the exit cone. The time-accurate calculation over-predicted the amplitude of the pressure variations at high flow.

Innovation Process Management and System Modelling

Työn tavoitteena oli perehtyä innovaatiojohtamisen ja järjestelmän soveltamiseen prosessiteollisuuden toimintaympäristöön. Kirjallisuuslähteitä apuna käyttäen perehdyttiin liiketoimintaympäristön innovaatiojohtamiselle asettamiin vaatimuksiin ja erilaisiin innovaatiojärjestelmiin. Olennaisena osana innovaatiojohtamiseen liittyy sidosryhmien tarpeiden ja niiden tarjoamien resurssien huomioiminen toiminnassa. Myöskin tuotekehityksen menetelmät ja työkalut ovat omalta osaltaan merkittävässä asemassa toiminnan tehokkuutta arvioitaessa. Innovaatiojärjestelmä tulee sopeuttaa yrityksen toimintoihin ja sen erityispiirteet huomioonottaen siten, että toiminnan johtaminen prosessina tuo yritykselle ja sen sidosryhmille lisäarvoa. Innovaatiojärjestelmän luominen yritykselle on ainayksilöllinen prosessi ja siihen ei ole olemassa yleispätevää menetelmää, joka voitaisiin ottaa käyttöön sellaisenaan. Yritys, jonka liiketoiminta keskittyy kuitupohjaisten pakkausmateriaalien valmistamiseen, joutuu täyttämään toiminnassaan materiaalintoimittajien, omien tuotantoprosessiensa ja asiakkaiden sekä jopa loppukäyttäjien uusille tuotteille luomat odotukset. Innovaatiojohtamista sävyttää toiminnan tulosten suuri epävarmuus ja sen vaativien aineellisten ja henkisten resurssien mittavuus. Innovaatiotoiminnan johtaminen prosessina, käyttäen hyväksi järjestelmämallia, tavoittelee systemaattista ja asetettujen kriteerien täyttämää lähestymistapaa tuotekehityksen ja uusien liiketoimintainnovaatioiden alueella. Kehitetyn mallin tulee palvella monimutkaista liiketoimintaympäristöä, jokatoisaalta perustuu tehokkaaseen massatuotantoon ja toisaalta pyrkii erilaistumaan palvelemalla sekä huomioimalla asiakkaidensa tuotteille asettamat vaatimukset.