Permanent magnet synchronous generator design solution for large directdrive wind turbines: Thermal behavior of the LC DD-PMSG

Wind is one of the most compelling forms of indirect solar energy. Available now, the conversion of wind power into electricity is and will continue to be an important element of energy self-sufficiency planning. This paper is one in a series intended to report on the development of a new type of generator for wind energy; a compact, high-power, direct-drive permanent magnet synchronous generator (DD-PMSG) that uses direct liquid cooling (LC) of the stator windings to manage Joule heating losses. The main param-eters of the subject LC DD-PMSG are 8 MW, 3.3 kV, and 11 Hz. The stator winding is cooled directly by deionized water, which flows through the continuous hollow conductor of each stator tooth-coil winding. The design of the machine is to a large degree subordinate to the use of these solid-copper tooth-coils. Both steady-state and timedependent temperature distributions for LC DD-PMSG were examined with calculations based on a lumpedparameter thermal model, which makes it possible to account for uneven heat loss distribution in the stator conductors and the conductor cooling system. Transient calculations reveal the copper winding temperature distribution for an example duty cycle during variable-speed wind turbine operation. The cooling performance of the liquid cooled tooth-coil design was predicted via finite element analysis. An instrumented cooling loop featuring a pair of LC tooth-coils embedded in a lamination stack was built and laboratory tested to verify the analytical model. Predicted and measured results were in agreement, confirming the predicted satisfactory operation of the LC DD-PMSG cooling technology approach as a whole.

Heat-transfer improvements in an axial-flux permanent-magnet synchronous machine

Axial-flux machines tend to have cooling difficulties since it is difficult to arrange continuous heat path between the stator stack and the frame. One important reason for this is that no shrink fitting of the stator is possible in an axial-flux machine. Using of liquid-cooled end shields does not alone solve this issue. Cooling of the rotor and the end windings may also be difficult at least in case of two-stator-single-rotor construction where air circulation in the rotor and in the end-winding areas may be difficult to arrange. If the rotor has significant losses air circulation via the rotor and behind the stator yokes should be arranged which, again, weakens the stator cooling. In this paper we study a novel way of using copper bars as extra heat transfer paths between the stator teeth and liquid cooling pools in the end shields. After this the end windings still suffer of low thermal conductivity and means for improving this by high-heat-conductance material was also studied. The design principle of each cooling system is presented in details. Thermal models based on Computational Fluid Dynamics (CFD) are used to analyse the temperature distribution in the machine. Measurement results are provided from different versions of the machine. The results show that significant improvements in the cooling can be gained by these steps.

Evaluation of the Efficiency of Line-Start Permanent-Magnet Machines as a Function of the Operating Temperature

The standard squirrel-cage induction machine has nearly reached its maximum efficiency. In order to further increase the energy efficiency of electrical machines, the use of permanent magnets in combination with the robust design and the line start capability of the induction machine is extensively investigated. Many experimental designs have been suggested in literature, but recently, these line-start permanent-magnet machines (LSPMMs) have become off-the-shelf products available in a power range up to 7.5 kW. The permanent magnet flux density is a function of the operating temperature. Consequently, the temperature will affect almost every electrical quantity of the machine, including current, torque, and efficiency. In this paper, the efficiency of an off-the-shelf 4-kW three-phase LSPMM is evaluated as a function of the temperature by both finite-element modeling and by practical measurements. In order to obtain stator, rotor, and permanent magnet temperatures, lumped thermal modeling is used.

Sähköisen liikkeenohjauskäytön mitoitus, käyttöönoton dokumentointi ja pakkauslinjasovellukset

Frequency converters have started to gain new market areas in the field of motion control applications. The communication and control properties of frequency converters have reached the properties of traditional servo amplifiers during the past few years. In this thesis a motion control system was examined. This particular system consists of frequency converters, permanent magnet synchronous motors and linear belt drives. The properties and prerequisites for packing are discussed. A test setup was build and measurement sets were done to examine the performance of the system. Speed and accuracy measurements were done in all three dimensions. Based on the measurement results applicability of the system for packing industry was evaluated.

Design of flywheel generator for a diesel hybrid working machine

The aim of this work is to design a flywheel generator for a diesel hybrid working machine. In this work we perform detailed design of a generator. Mobile machines are commonly used in industry: road building machines, three harvesting machines, boring machines, trucks and other equipment. These machines work with a hydraulic drive system. This system provides good service property and high technical level. Manufacturers of mobile machines tend to satisfy all requirements of customers and modernized drive system. In this work also a description of the frequency inverter is present. Power electronics system is one of the basic parts for structures perform in the project.

Eddy-current losses in rotor surface mounted permanent magnets

The aim of the work is to study the existing analytical calculation procedures found in literature to calculate the eddy-current losses in surface mounted permanent magnets within PMSM application. The most promising algorithms are implemented with MATLAB software under the dimensional data of LUT prototype machine. In addition finite elements analyze, utilized with help of Flux 2D software from Cedrat Ltd, is applied to calculate the eddy-current losses in permanent magnets. The results obtained from analytical methods are compared with numerical results.

Erikoissähkökoneen tyyppitestaus

Uusien erikoissähkökoneiden testaus perinteisten standardien mukaan on osittain haasteellista. Erikoissähkökoneille, kuten kestomagneettitahtikoneelle ei ole esitetty suoranaisia standardin vaatimia testejä, joten siihen joudutaan soveltamaan olemassa olevia erillismagnetoiduntahtikoneen standardeja. Testien tavoitteena on olla luotettavia sekä vertailukelpoisia. Mittausten on oltava toistettavissa. Mittaustavasta riippuen voidaan saada erilaisia tuloksia, jotka vaikuttavat lopputulokseen. Standardien mukaisessa testauksessa saadaan mittauksista samanlaisia ja samalla saadaan mittausvirheen mahdollisuus pienemmäksi ja tällä tavoin tulokset keskenään vertailukelpoisemmiksi. Tässä työssä tarkastellaan kahta erilaista erikoissähkokonetta, kestomagneettitahtikonetta ja massiiviroottoriepätahtikonetta. Työssä selvitetään standardin IEC 60034 soveltuvuutta tyyppitesteihin, joita kyseiset konetyypit vaativat. Lisäksi työssä vertaillaan standardin IEC 60034 mukaisen hyötysuhteen määrittämistä. Se antaakin useita vaihtoehtoja hyötysuhteen määrittämiselle.

Design of marine generators for alternative diesel-electric power systems

This study compares different electric propulsion systems. Results of the analysis of all the advantages and disadvantages of the different propulsion systems are given. This thesis estimates possibilities to apply different diesel-electric propulsion concepts for different vessel types. Small and medium size vessel’s power ranges are studied. The optimal delivery system is chosen. This choice is made on the base of detailed study of the concepts, electrical equipment market and comparison of mass, volume and efficiency parameters. In this thesis three marine generators are designed. They are: salient pole synchronous generator and two permanent magnet synchronous generators. Their electrical, dimensional, cost and efficiency parameters are compared. To understand all the benefits diagrams with these parameters are prepared. Possible benefits and money savings are estimated. As the result the advantages, disadvantages and boundary conditions for the permanent magnet synchronous generator application in marine electric-power systems are found out.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.

Hysteresis Losses in Sintered NdFeB Permanent Magnets in Rotating Electrical Machines

Permanent magnet materials are nowadays widely used in the electrical machine manufacturing industry. Eddy current loss models of permanent magnets used in electrical machines are frequently discussed in research papers. In magnetic steel materials we have, in addition to eddy current losses, hysteresis losses when AC or a rotating flux travels through the material. Should a similar phenomenon also be taken into account in calculating the losses of permanent magnets? Actually, every now and then authors seem to assume that some significant hysteresis losses are present in rotating machine PMs. This paper studies the mechanisms of possible hysteresis losses in PMs and their role in PMs when used in rotating electrical machines.

Design of a Traction Motor With Tooth-Coil Windings and Embedded Magnets

Traction motor design significantly differs from industrial machine design. The starting point is the load cycle instead of the steady-state rated operation point. The speed of the motor varies from zero to very high speeds. At low speeds, heavy overloading is used for starting, and the field-weakening region also plays an important role. Finding a suitable fieldweakening point is one of the important design targets. At the lowest speeds, a high torque output is desired, and all current reserves of the supplying converter unit are used to achieve the torque. In this paper, a 110-kW 2.5-p.u. starting torque and a maximum 2.5-p.u. speed permanent-magnet traction motor will be studied. The field-weakening point is altered by varying the number of winding turns of machine. One design is selected for prototyping. Theoretical results are verified by measurements.

Sähkökoneen staattorikäämityksen kehittäminen

Tämä insinöörityö tehtiin ABB:n Pitäjänmäen konetehtaalle Tahtikoneet-tulosyksikölle. Työssä tutkittiin mahdollisuuksia valmistaa murtovakovyyhtejä kestomagneettituuligeneraattoreihin, joissa vakoluku on alle yhden. Työ tehtiin tutustumalla aluksi Pitäjänmäen konetehtaan käytössä oleviin vyyhden valmistus- ja käämintämenetelmiin. Lisäksi tutkittiin erilaisia mahdollisia murtovakovyyhden valmistusmenetelmiä, joista lupaavimpia myös kokeiltiin. Saatujen kokemusten pohjalta valittiin vyyhden valmistusmenetelmä, jonka mukaan valmistettiin koe-erä. Koe-erälle suoritettiin mittauksia, joilla varmistettiin niiden sähköinen kestävyys Työn tuloksena valitulla valmistusmenetelmällä valmistettiin vyyhdet prototyyppi tuuligeneraattorin.

Designing Digital Filters for Servo Systems

The aim of this work was to select an appropriate digital filter for a servo application and to filter the noise from the measurement devices. Low pass filter attenuates the high frequency noise beyond the specified cut-off frequency. Digital lowpass filters in both IIR and FIR responses were designed and experimentally compared to understand their characteristics from the corresponding step responses of the system. Kaiser Windowing and Equiripple methods were selected for FIR response, whereas Butterworth, Chebyshev, InverseChebyshev and Elliptic methods were designed for IIR case. Limitations in digital filter design for a servo system were analysed. Especially the dynamic influences of each designed filter on the control stabilityof the electrical servo drive were observed. The criterion for the selection ofparameters in designing digital filters for servo systems was studied. Control system dynamics was given significant importance and the use of FIR and IIR responses in different situations were compared to justify the selection of suitableresponse in each case. The software used in the filter design was MatLab/Simulink® and dSPACE's DSP application. A speed controlled Permanent Magnet Linear synchronous Motor was used in the experimental work.

Napakäämityn murtovakokestomagneettitahtikoneen suunnittelu

Diplomityössä tutustutaan napakäämittyihin murtovakokestomagneettitahtikoneisiin sekä syvennytään niiden suunnitteluun analyyttisen laskennanavulla. Analyyttisen laskennan haasteena on perinteisesti käytettyjen kestomagneettitahtikoneiden laskentayhtälöiden sovittaminen murtovakokäämityille kestomagneettitahtikoneille. Työn lopussa analyyttisen laskennan tuloksia verrataan kenttälaskentaohjelmalla saatuihin tuloksiin. Tärkeimmät analyyttiset yhtälöt sekä laskentamallin rakenne on esitetty työssä.

Kestomagneettitahtikoneen lämpömallinnus

Sähkökoneenterminen suunnittelu on yhtä tärkeätä kuin koneen sähköisten piirien ja magneettipiirin mitoitus, koska koneen lämpenemä määrää koneesta saatavan tehon. Pääosasähkökoneista suunnitellaan edelleen ns. perimätiedon avulla, jossa tukeudutaanvalmiiksi koeteltuihin ratkaisuihin ja kokemusperäiseen tietoon tiettyjen rakenteiden toimivuudesta. Perinteisin menetelmin uusia konerakenteita suunniteltaessa ei pystytä saamaan luotettavaa tietoa uusien ratkaisuiden toimivuudesta. Etenkin hitaasti pyörivien ja suuren vääntötiheyden omaavien kestomagneettitahtikoneiden jäähdytyksen mitoitus on ongelmallista. Siten tarve kehittää analyyttisiä työkaluja lämpenemän mallinnukseen on perusteltua. Tässä työssäperehdytään suuren tehotiheyden omaavien kestomagneettikoneiden urakoon ja virrantiheyden valintaan termisen mitoituksen kannalta. Työn tavoitteena on laatia yksinkertainen analyyttinen työkalu urakoon ja virrantiheyden valintaan. Työkaluavoidaan hyödyntää jo koneensuunnittelun alkuvaiheessa.