Machine vision measurement system for paper printability assessments

This work had two primary objectives: 1) to produce a working prototype for automated printability assessment and 2) to perform a study of available machine vision and other necessary hardware solutions. The three printability testing methods, IGT Picking,He¬liotest, and mottling, considered in this work have several different requirements and the task was to produce a single automated testing system suitable for all methods. A system was designed and built and its performance was tested using the Heliotest. Working proto¬types are important tools for implementing theoretical methods into practical systems and testing and demonstrating the methodsin real life conditions. The system was found to be sufficient for the Heliotest method. Further testing and possible modifications related to other two test methods were left for future works. A short study of available systems and solutions concerning image acquisition of machine vision was performed. The theoretical part of this study includes lighting systems, optical systems and image acquisition tools, mainly cameras and the underlying physical aspects for each portion.

Turvallisuustoimintojen käyttö ydinvoimalaitoksilla

Tässä diplomityössä tarkastellaan turvallisuustoiminto-käsitteen määrittelyä ja käyttöä osana ydinvoimalaitosten turvallisuuden varmistamista. Työssä kuvataan paine- ja kiehutusvesilaitosten toiminnan yleispiirteet, sekä Teollisuuden Voima Oy:n (TVO) laitosten Olkiluoto 1 & 2 sekä Olkiluoto 3 tarkempi turvallisuustoiminta turvallisuusjärjestelmien ja -automaation osalta. Työssä esitellään eräs tapa määrittää turvallisuustoimintoja. Malli perustuu hierarkkiseen rakenteeseen, jossa ylimpänä ovat laitostason turvallisuustoiminnot ja alimpana turvallisuustoimintoihin osallistuvien laitteiden ja niiden osien toiminnot. Turvallisuustoimintoja on mahdollista käyttää ydinvoimalaitoksen turvallisuusluokituksen tekemiseen ja perustelemiseen. Turvallisuustoiminto kertoo suoraan luokiteltavan kohteen turvallisuusmerkityksen. Kohteen turvallisuusmerkityksen selvittäminen, eli liittäminen turvallisuustoimintoon, voi olla vaikeaa. Turvallisuustoimintoja on myös mahdollista käyttää laitoksen turvallisuusautomaation riittävän varmistamisen (mm. redundanttisuus, diversiteetti ja erotus) osoittamiseen erityisesti ohjelmoitavan automaation yhteydessä. Turvallisuustoimintoja voidaan hyödyntää laitoksen hätätilanneohjeiden kehittämisessä ja myös laitoksenmuun turvallisuusdokumentaation selkeyttämisessä. Työn tuloksena kehitettiin käyville laitoksille (OL1 & 2) aikaisempaa kattavammat turvallisuustoiminnot. Lisäksi tarkasteltiin rakenteilla olevalle laitokselle (OL3) määriteltyjä turvallisuustoimintoja.

Retinal Image Analysis Using Machine Vision

The topic of this thesis is studying how lesions in retina caused by diabetic retinopathy can be detected from color fundus images by using machine vision methods. Methods for equalizing uneven illumination in fundus images, detecting regions of poor image quality due toinadequate illumination, and recognizing abnormal lesions were developed duringthe work. The developed methods exploit mainly the color information and simpleshape features to detect lesions. In addition, a graphical tool for collecting lesion data was developed. The tool was used by an ophthalmologist who marked lesions in the images to help method development and evaluation. The tool is a general purpose one, and thus it is possible to reuse the tool in similar projects.The developed methods were tested with a separate test set of 128 color fundus images. From test results it was calculated how accurately methods classify abnormal funduses as abnormal (sensitivity) and healthy funduses as normal (specificity). The sensitivity values were 92% for hemorrhages, 73% for red small dots (microaneurysms and small hemorrhages), and 77% for exudates (hard and soft exudates). The specificity values were 75% for hemorrhages, 70% for red small dots, and 50% for exudates. Thus, the developed methods detected hemorrhages accurately and microaneurysms and exudates moderately.

Stability Evaluation of a Paper Machine Wet End

Työssä analysoidaanprosessin vaikutusta paperikoneen stabiiliuteen. Kaksi modernia sanomalehtipaperikonetta analysoitiin ja sen perusteella molemmista prosesseista rakennettiin fysiikan lakeihin perustuvat simulointimallit APROS Paper simulointiohjelmistolla. Työn tavoitteena on selvittää, miten kyseisten koneiden prosessit eroavat toisistaan ja arvioida, miten havaitut erot vaikuttavat prosessien stabiiliuteen. Työssä tarkastellaan periodisten häiriöiden vaimenemista prosessissa. Simuloinnissa herätteenä käytettiin puhdasta valkoista kohinaa, jonka avulla eri taajuistenperiodisten häiriöiden vaimenemista analysoitiin. Prosessien häiriövasteet esitetään taajuuskoordinaatistossa. Suurimmat erot prosessien välillä löytyivät viirakaivosta ja sen sekoitusdynamiikasta. Perinteisen viirakaivon todettiin muistuttavan käyttäytymiseltään sarjaan kytkettyjä ideaalisekoittimia, kun taas pienempitilavuuksisen fluumin todettiin käyttäytyvän lähes kuin putkiviive. Vaikka erotprosessitilavuudessa sekä viirakaivon sekoitusdynamiikassa olivat hyvin selkeät, havaittiin vain marginaalinen ero prosessin välillä periodisten häiriöiden vaimenemisessa, koska erot viiraretentiotasoissa vaikuttivat eniten simulointituloksia. Matalammalla viiraretentiolla operoivan paperikoneen todettiin vaimentavan tehokkaammin prosessihäiriöitä. Samalla retentiotasolla pienempitilavuuksisen prosessin todettiin vaimentavan hitaita prosessihäiriöitä marginaalisesti paremmin. Tutkituista paperikoneista toisella simuloitiin viiraosan vedenpoistomuutoksenvaikutusta viiraretentioon ja paperin koostumukseen. Lisäksi arvioitiin viiraretention säädön toimivuutta. Viiraosan listakengän vedenpoiston todettiin aiheuttavan merkittäviä sakeus- ja retentiohäiriöitä, mikäli sen avulla poistettavan kiintoaineen virtaus tuplaantuisi. Viiraretention säädön todettiin estävän häiriöiden kierron prosessissa, mutta siirtävän ne suoraan rainaan. Retention säädön eikuitenkaan todettu olevan suoranainen häiriön lähde.

Optinen merkintunnistus satamaliikenteessä ja junavaunujen tunnistamisessa

Optisella merkintunnistuksella on tärkeä rooli nykypäivän automaatiossa. Optisen merkintunnistuksen eri sovellusalueet vaihtelevat dokumenttien tekstin tunnistamisesta ajoneuvojen tunnistamiseen ja erilaisten tuotanto- ja kokoonpanolinjojen automaatioon ja laadun tarkkailuun. Tässä työssä keskitytään optisen merkintunnistuksen käyttöön satamaliikenteessä. Työ jakaantuu kahteen osaan. Ensimmäisessä osassa esitellään satamien kannalta kaksi yleisintä ja samalla tärkeintä optisen merkintunnistuksen sovellusaluetta: rekisterikilpien tunnistus ja konttien tunnistus. Työn jälkimmäinen osa käsittelee junavaunujen tunnistamista optisen merkintunnistuksen avulla. Satamissa toimiva vaunukalusto ja niissä esiintyvät tunnisteet esitellään. Vaunujen tunnistamisen toteuttava konenäköjärjestelmä, sen vaativat laitteet sekä kuvankäsittelyn ja kuva-analyysin vaiheet käydään läpi. Kuva-analyysion jaettu työssä neljään päävaiheeseen: esikäsittely, segmentointi, piirreirrotus ja luokittelu. Kustakin vaiheesta esitetään useita eri menetelmiä, joiden käyttökelpoisuutta esitettyyn ongelmaan arvioidaan työn lopussa.

Modernisation of bar mill automation

Työn tavoitteena on tankovalssaamon perusautomaation modernisointi Ovako Bar Oy Ab:n Imatran terästehtaalla. Vanha automaatiojärjestelmä on toteutettu 80-luvun puoli-välin tekniikalla käyttämällä Siemens Sicomp MMC 216 moniprosessori-tietokonetta, Siemens Simatic S5 logiikkayksiköitä sekä Siemens Simadyn D DC-käyttöjä. Modernisoinnin tarkoituksena on korvata vanha automaatiojärjestelmä Siemens PCS7 -järjestelmällä siten, että tankovalssaamon automaatiojärjestelmä voidaan liittää osaksi jo aiemmin modernisoituja, nykyisin PCS7 automaatiojärjestelmällä toteutettuja ratkaisu-ja. Valssaamon mekaniikka ei mahdollista tuotannon kasvattamista pelkästään uuden automaatiojärjestelmän avulla, joten modernisointi keskittyy parantamaan järjestelmän luotettavuutta ja helpottamaan ylläpitoa. Projekti päätettiin jakaa kolmeen osaan, jotka voidaan toteuttaa erillisinä osaprojekteina. Tärkein osaprojekti on MMC järjestelmän uusinta. Muut osaprojektit ovat DC-käyttöjen sekä ohjelmoitavien logiikkojen modernisointi. Osaprojektit valittiin siten, että mikä tahansa niistä voidaan toteuttaaerillisenä projektinaan, mikäli kaikkia osia ei voida mo-dernisoida samanaikaisesti budjetin asettamien rajoitusten vuoksi.

Project controlling and risk management in German machine and plant engineering industry

Tutkielman tavoitteena on määritellä projektikontrolloinnin ja - riskijohtamisen roolit ja toiminnot saksalaisissa kone- ja tehdassuunnitteluteollisuusyrityksissä. Tämä on kvalitatiivinen tutkielma, jossa käytetään voimakkaasti kuvailevia metodeita. Materiaali tutkimuksen empiiriseen osaan kerättiin kyselykaavakkeen avulla. Kyselykaavakkeiden tulokset käsiteltiin Microsoft Office Access- ohjelmalla ja analysoitiin Microsoft Office Excel- ohjelmalla ja Pivot table- työkalun avulla. Tutkimustulokset osoittavat, että asianmukaisessa projektikontrollointi- ja riskijohtamismetodien käytössä ja käyttötiheydessä esiintyy puutteita saksalaisissa kone- ja tehdassuunnitteluteollisuusyrityksissä. Tehostamalla ja keskittymällä enemmän projektikontrollointi- ja riskijohtamismetodeihin ja prosesseihin sekä projektien että yritysten suorituskyky paranisi.

Revenue Logic inSoftware Business Context

Tutkimuksen tavoitteena oli selvittää ohjelmistotoimialan avaintekijöitä, jotka vaikuttavat yrityksen ansaintalogiikkaan sekä lisätä tietoisuutta ansaintalogiikan muodostumisesta pienissä ja keskisuurissa ohjelmistoyrityksissä. Tutkimuksen teoreettisessa osassa keskityttiin tarkastelemaan ansaintalogiikan, strategian ja liiketoimintamallin käsitteiden suhteita sekä arvioitiin toimialan osatekijöiden, hinnoitteluperiaatteiden ja ansaintamallien vaikutusta ansainnan muodostumiseen ohjelmistotoimialalla. Ohjelmistotuote ja - palveluliiketoimintaa koskien oli merkityksellistä tutkia tuotteistamisasteen ja arvoketjujen vaikutusta ansaintalogiikan muodostumisessa sekä esitellä erilaisia, tyypillisiä ohjelmistotoimialalla käytettäviä hinnoittelumenetelmiä. Työn empiirisessä osassa tarkasteltiin 23 suomalaisen ohjelmistoalan yrityksen ansaintalogiikkaa. Tiedot kerättiin haastatteluin ja analysoitiin laadullisen tutkimuksen keinoin. Tutkimustulokset korostivat ansaintalogiikan 'epämääräisyyttä' terminä mutta osoittivat, että ydinliiketoimintaan keskittyminen, tuote-, palvelu-, tai projektiliiketoiminnan osaaminen, tuotteistusaste ja kanavavalinnat ovat avaintekijöitä ansaintalogiikanmuodostumisessa. Ansaintalogiikan muodostamiseen liittyy paljon yrityksen sisäisiä ja ulkoisia haasteita sekä muutospaineita, eikä ohjelmistotoimialalla ole todennettavissa yhtä yleismaailmallista, menestyksen takaavaa ansaintalogiikkaa.

Aspects on Process Engineering in the Finnish Pulp and Paper Industry : Thesis for the Degree of Licentiate in Science of Technology

Process development will be largely driven by the main equipment suppliers. The reason for this development is their ambition to supply complete plants or process systems instead of single pieces of equipment. The pulp and paper companies' interest lies in product development, as their main goal is to create winning brands and effective brand management. Design engineering companies will find their niche in detail engineering based on approved process solutions. Their development work will focus on increasing the efficiency of engineering work. Process design is a content-producing profession, which requires certain special characteristics: creativity, carefulness, the ability to work as a member of a design team according to time schedules and fluency in oral as well as written presentation. In the future, process engineers will increasingly need knowledge of chemistry as well as information and automation technology. Process engineering tools are developing rapidly. At the moment, these tools are good enough for static sizing and balancing, but dynamic simulation tools are not yet good enough for the complicated chemical reactions of pulp and paper chemistry. Dynamic simulation and virtual mill models are used as tools for training the operators. Computational fluid dynamics will certainlygain ground in process design.

Choice of Optimal MembraneProcesses for Economical Treatment of Paper Machine Clear Filtrate

In this thesis membrane filtration of paper machnie clear filtrate was studied. The aim of the study was to find membrane processes which are able to produce economically water of sufficient purity from paper machine white water or its saveall clarified fractions for reuse in the paper machnie short circulation. Factors affecting membrane fouling in this application were also studied. The thesis gives an overview af experiments done on a laboratory and a pilot scale with several different membranes and membrane modules. The results were judged by the obtained flux, the fouling tendency and the permeate quality assessed with various chemical analyses. It was shown that membrane modules which used a turbulence promotor of some kind gave the highest fluexes. However, the results showed that the greater the reduction in the concentration polarisation layer caused by increased turbulence in the module, the smaller the reductions in measured substances. Out of the micro-, ultra- and nanofiltration membranes tested, only nanofiltration memebranes produced permeate whose quality was very close to that of the chemically treated raw water used as fresh water in most paper mills today and which should thus be well suited for reuse as shower water both in the wire and press section. It was also shown that a one stage nanofiltration process was more effective than processes in which micro- or ultrafiltration was used as pretreatment for nanofiltration. It was generally observed that acidic pH, high organic matter content, the presence of multivalent ions, hydrophobic membrane material and high membrane cutoff increased the fouling tendency of the membranes.

Numerical and ExperimentalModelling of Gas Flow and Heat Transfer in the Air Gap of An Electric Machine

This work deals with the cooling of high-speed electric machines, such as motors and generators, through an air gap. It consists of numerical and experimental modelling of gas flow and heat transfer in an annular channel. Velocity and temperature profiles are modelled in the air gap of a high-speed testmachine. Local and mean heat transfer coefficients and total friction coefficients are attained for a smooth rotor-stator combination at a large velocity range. The aim is to solve the heat transfer numerically and experimentally. The FINFLO software, developed at Helsinki University of Technology, has been used in the flow solution, and the commercial IGG and Field view programs for the grid generation and post processing. The annular channel is discretized as a sector mesh. Calculation is performed with constant mass flow rate on six rotational speeds. The effect of turbulence is calculated using three turbulence models. The friction coefficient and velocity factor are attained via total friction power. The first part of experimental section consists of finding the proper sensors and calibrating them in a straight pipe. After preliminary tests, a RdF-sensor is glued on the walls of stator and rotor surfaces. Telemetry is needed to be able to measure the heat transfer coefficients at the rotor. The mean heat transfer coefficients are measured in a test machine on four cooling air mass flow rates at a wide Couette Reynolds number range. The calculated values concerning the friction and heat transfer coefficients are compared with measured and semi-empirical data. Heat is transferred from the hotter stator and rotor surfaces to the coolerair flow in the air gap, not from the rotor to the stator via the air gap, althought the stator temperature is lower than the rotor temperature. The calculatedfriction coefficients fits well with the semi-empirical equations and precedingmeasurements. On constant mass flow rate the rotor heat transfer coefficient attains a saturation point at a higher rotational speed, while the heat transfer coefficient of the stator grows uniformly. The magnitudes of the heat transfer coefficients are almost constant with different turbulence models. The calibrationof sensors in a straight pipe is only an advisory step in the selection process. Telemetry is tested in the pipe conditions and compared to the same measurements with a plain sensor. The magnitudes of the measured data and the data from the semi-empirical equation are higher for the heat transfer coefficients than thenumerical data considered on the velocity range. Friction and heat transfer coefficients are presented in a large velocity range in the report. The goals are reached acceptably using numerical and experimental research. The next challenge is to achieve results for grooved stator-rotor combinations. The work contains also results for an air gap with a grooved stator with 36 slots. The velocity field by the numerical method does not match in every respect the estimated flow mode. The absence of secondary Taylor vortices is evident when using time averagednumerical simulation.

Torque vibration model of axial-flux surface-mounted permanent magnet synchronous machine

In order that the radius and thus ununiform structure of the teeth and otherelectrical and magnetic parts of the machine may be taken into consideration the calculation of an axial flux permanent magnet machine is, conventionally, doneby means of 3D FEM-methods. This calculation procedure, however, requires a lotof time and computer recourses. This study proves that also analytical methods can be applied to perform the calculation successfully. The procedure of the analytical calculation can be summarized into following steps: first the magnet is divided into slices, which makes the calculation for each section individually, and then the parts are submitted to calculation of the final results. It is obvious that using this method can save a lot of designing and calculating time. Thecalculation program is designed to model the magnetic and electrical circuits of surface mounted axial flux permanent magnet synchronous machines in such a way, that it takes into account possible magnetic saturation of the iron parts. Theresult of the calculation is the torque of the motor including the vibrations. The motor geometry and the materials and either the torque or pole angle are defined and the motor can be fed with an arbitrary shape and amplitude of three-phase currents. There are no limits for the size and number of the pole pairs nor for many other factors. The calculation steps and the number of different sections of the magnet are selectable, but the calculation time is strongly depending on this. The results are compared to the measurements of real prototypes. The permanent magnet creates part of the flux in the magnetic circuit. The form and amplitude of the flux density in the air-gap depends on the geometry and material of the magnetic circuit, on the length of the air-gap and remanence flux density of the magnet. Slotting is taken into account by using the Carter factor in the slot opening area. The calculation is simple and fast if the shape of the magnetis a square and has no skew in relation to the stator slots. With a more complicated magnet shape the calculation has to be done in several sections. It is clear that according to the increasing number of sections also the result will become more accurate. In a radial flux motor all sections of the magnets create force with a same radius. In the case of an axial flux motor, each radial section creates force with a different radius and the torque is the sum of these. The magnetic circuit of the motor, consisting of the stator iron, rotor iron, air-gap, magnet and the slot, is modelled with a reluctance net, which considers the saturation of the iron. This means, that several iterations, in which the permeability is updated, has to be done in order to get final results. The motor torque is calculated using the instantaneous linkage flux and stator currents. Flux linkage is called the part of the flux that is created by the permanent magnets and the stator currents passing through the coils in stator teeth. The angle between this flux and the phase currents define the torque created by the magnetic circuit. Due to the winding structure of the stator and in order to limit the leakage flux the slot openings of the stator are normally not made of ferromagnetic material even though, in some cases, semimagnetic slot wedges are used. In the slot opening faces the flux enters the iron almost normally (tangentially with respect to the rotor flux) creating tangential forces in the rotor. This phenomenon iscalled cogging. The flux in the slot opening area on the different sides of theopening and in the different slot openings is not equal and so these forces do not compensate each other. In the calculation it is assumed that the flux entering the left side of the opening is the component left from the geometrical centre of the slot. This torque component together with the torque component calculated using the Lorenz force make the total torque of the motor. It is easy to assume that when all the magnet edges, where the derivative component of the magnet flux density is at its highest, enter the slot openings at the same time, this will have as a result a considerable cogging torque. To reduce the cogging torquethe magnet edges can be shaped so that they are not parallel to the stator slots, which is the common way to solve the problem. In doing so, the edge may be spread along the whole slot pitch and thus also the high derivative component willbe spread to occur equally along the rotation. Besides forming the magnets theymay also be placed somewhat asymmetric on the rotor surface. The asymmetric distribution can be made in many different ways. All the magnets may have a different deflection of the symmetrical centre point or they can be for example shiftedin pairs. There are some factors that limit the deflection. The first is that the magnets cannot overlap. The magnet shape and the relative width compared to the pole define the deflection in this case. The other factor is that a shifting of the poles limits the maximum torque of the motor. If the edges of adjacent magnets are very close to each other the leakage flux from one pole to the other increases reducing thus the air-gap magnetization. The asymmetric model needs some assumptions and simplifications in order to limit the size of the model and calculation time. The reluctance net is made for symmetric distribution. If the magnets are distributed asymmetrically the flux in the different pole pairs will not be exactly the same. Therefore, the assumption that the flux flows from the edges of the model to the next pole pairs, in the calculation model from one edgeto the other, is not correct. If it were wished for that this fact should be considered in multi-pole pair machines, this would mean that all the poles, in other words the whole machine, should be modelled in reluctance net. The error resulting from this wrong assumption is, nevertheless, irrelevant.

A mathematical study of fuzzy logic; an algebraic approach

Fuzzy set theory and Fuzzy logic is studied from a mathematical point of view. The main goal is to investigatecommon mathematical structures in various fuzzy logical inference systems and to establish a general mathematical basis for fuzzy logic when considered as multi-valued logic. The study is composed of six distinct publications. The first paper deals with Mattila'sLPC+Ch Calculus. THis fuzzy inference system is an attempt to introduce linguistic objects to mathematical logic without defining these objects mathematically.LPC+Ch Calculus is analyzed from algebraic point of view and it is demonstratedthat suitable factorization of the set of well formed formulae (in fact, Lindenbaum algebra) leads to a structure called ET-algebra and introduced in the beginning of the paper. On its basis, all the theorems presented by Mattila and many others can be proved in a simple way which is demonstrated in the Lemmas 1 and 2and Propositions 1-3. The conclusion critically discusses some other issues of LPC+Ch Calculus, specially that no formal semantics for it is given.In the second paper the characterization of solvability of the relational equation RoX=T, where R, X, T are fuzzy relations, X the unknown one, and o the minimum-induced composition by Sanchez, is extended to compositions induced by more general products in the general value lattice. Moreover, the procedure also applies to systemsof equations. In the third publication common features in various fuzzy logicalsystems are investigated. It turns out that adjoint couples and residuated lattices are very often present, though not always explicitly expressed. Some minor new results are also proved.The fourth study concerns Novak's paper, in which Novak introduced first-order fuzzy logic and proved, among other things, the semantico-syntactical completeness of this logic. He also demonstrated that the algebra of his logic is a generalized residuated lattice. In proving that the examination of Novak's logic can be reduced to the examination of locally finite MV-algebras.In the fifth paper a multi-valued sentential logic with values of truth in an injective MV-algebra is introduced and the axiomatizability of this logic is proved. The paper developes some ideas of Goguen and generalizes the results of Pavelka on the unit interval. Our proof for the completeness is purely algebraic. A corollary of the Completeness Theorem is that fuzzy logic on the unit interval is semantically complete if, and only if the algebra of the valuesof truth is a complete MV-algebra. The Compactness Theorem holds in our well-defined fuzzy sentential logic, while the Deduction Theorem and the Finiteness Theorem do not. Because of its generality and good-behaviour, MV-valued logic can be regarded as a mathematical basis of fuzzy reasoning. The last paper is a continuation of the fifth study. The semantics and syntax of fuzzy predicate logic with values of truth in ana injective MV-algerba are introduced, and a list of universally valid sentences is established. The system is proved to be semanticallycomplete. This proof is based on an idea utilizing some elementary properties of injective MV-algebras and MV-homomorphisms, and is purely algebraic.

Tilastotietojen graafinen esittäminen WWW-sivulla

World Wide Webin suosiolla on ollut merkittävä vaikutus yhteiskuntaan. WWW-sivut ovat helposti saatavilla ja sisällön tekeminen WWW:hen on helppoa. WWW-ympäristölle myös kehitetään paljon sovelluksia. WWW-sovellusten kehittämiselle ominaista on valinnanvapaus ja nopeuden tavoittelu. WWW-sovellusten ohjelmoinnin mahdollistavat useat toisilleen vaihtoehtoiset tekniikat. Ne eroavat toisistaan suoritusnopeudessa, ominaisuuksien määrässä ja joustavuudessa. Ohjelmoinnissa käytetään apuna useita erilaisia menetelmiä. Apumenetelmiä ovat muun muassa työkalut ja valmiiden komponenttien hyödyntäminen. Valmiit komponentit voivat olla joko ilmaisia, avointa lähdekoodia tai maksullisia. Tämän kandidaatintyön aikana valmistui sovellus, joka piirtää tilastotiedoista kaaviokuvia ja näyttää niitä dynaamisella WWW-sivulla. Sovellus pyrittiin toteuttamaan älykkäästi apumenetelmiä sopivasti hyödyntäen. Sovelluksen kehittämisessä käytettiin apuna sekä ohjelmointityökaluja että valmiita komponentteja. Kaaviokuvien tyypin ja ulkoasun haluttiin olevan käyttäjien muokattavissa. Toisaalta sovelluksen haluttiin olevan helposti laajennettavissa. Vaatimuksiin vastattiin tekemällä kaaviokuvien piirrosta osittain tietokannalla ohjelmoitava.

Design and implementation of FPGA-based LQ control of active magnetic bearings

The need for high performance, high precision, and energy saving in rotating machinery demands an alternative solution to traditional bearings. Because of the contactless operation principle, the rotating machines employing active magnetic bearings (AMBs) provide many advantages over the traditional ones. The advantages such as contamination-free operation, low maintenance costs, high rotational speeds, low parasitic losses, programmable stiffness and damping, and vibration insulation come at expense of high cost, and complex technical solution. All these properties make the use of AMBs appropriate primarily for specific and highly demanding applications. High performance and high precision control requires model-based control methods and accurate models of the flexible rotor. In turn, complex models lead to high-order controllers and feature considerable computational burden. Fortunately, in the last few years the advancements in signal processing devices provide new perspective on the real-time control of AMBs. The design and the real-time digital implementation of the high-order LQ controllers, which focus on fast execution times, are the subjects of this work. In particular, the control design and implementation in the field programmable gate array (FPGA) circuits are investigated. The optimal design is guided by the physical constraints of the system for selecting the optimal weighting matrices. The plant model is complemented by augmenting appropriate disturbance models. The compensation of the force-field nonlinearities is proposed for decreasing the uncertainty of the actuator. A disturbance-observer-based unbalance compensation for canceling the magnetic force vibrations or vibrations in the measured positions is presented. The theoretical studies are verified by the practical experiments utilizing a custom-built laboratory test rig. The test rig uses a prototyping control platform developed in the scope of this work. To sum up, the work makes a step in the direction of an embedded single-chip FPGA-based controller of AMBs.