Calculation of the critical crack size for cold form rectangular hollow section tube (CRHS) under bending load at -40º C temperature

To predict the capacity of the structure or the point which is followed by instability, calculation of the critical crack size is important. Structures usually contain several cracks but not necessarily all of these cracks lead to failure or reach the critical size. So, defining the harmful cracks or the crack size which is the most leading one to failure provides criteria for structure’s capacity at elevated temperature. The scope of this thesis was to calculate fracture parameters like stress intensity factor, the J integral and plastic and ultimate capacity of the structure to estimate critical crack size for this specific structure. Several three dimensional (3D) simulations using finite element method by Ansys program and boundary element method by Frank 3D program were carried out to calculate fracture parameters and results with the aid of laboratory tests (loaddisplacement curve, the J resistance curve and yield or ultimate stress) leaded to extract critical size of the crack. Two types of the fracture which is usually affected by temperature, Elastic and Elasti-Plastic fractures were simulated by performing several linear elastic and nonlinear elastic analyses. Geometry details of the weldment; flank angle and toe radius were also studied independently to estimate the location of crack initiation and simulate stress field in early stages of crack extension in structure. In this work also overview of the structure’s capacity in room temperature (20 ºC) was studied. Comparison of the results in different temperature (20 ºC and -40 ºC) provides a threshold of the structure’s behavior within the defined range.

Factors affecting the usability of aspen (Populus tremula) wood dried at different temperature levels

In this dissertation the main aim was to study the usability of aspen wood in the mechanical wood processes, especially the factors that affect the usability of aspen wood, which is dried at different temperature levels. The problematic of varying temperatures from level to another seem to have significant effects on distortions. According to the studies conducted, many practical solutions for drying of aspen timber can be made. European aspen sawn timber should be dried in relatively narrow widths, short lengths, edged and sawn pith free. The results achieved give an interesting view for the distortions of aspen wood between HT drying and heat treatment. The most significant result is that cupping seems to decrease when increasing temperature level from HT drying to heat treatment phase. The difference is significant. Other very obvious result is that bow and crook are increasing between these two temperature levels, bow significantly. Also the modelling gives a good background for this result since cupping is reduced by higher temperatures. It can also be assumed that these distortions can be affected for example by sorting out the timber used to different moisture levels before drying. This could be a very simple solution for practical purposes. From practical point of view, it was also noted during the drying tests performed that the discoloration seem to be no problem for aspen boards dried in temperatures under 150 °C. Altogether, this dissertation covers many interesting points of view of factors affecting distortions of wood in different temperature stages. Aspen as species in use of mechanical wood industries seems to be a species suitable for component production. According to the results, the best yield from aspen timber can be achieved in industry that can utilize relatively short components of sawn wood. Results achieved give a significant indication about the factors affecting distortions of wood at different temperature stages of drying, especially considering European aspen.

Climate driven changes in temperature, pH and food quality : effects on copepod reproduction

Increased emissions of greenhouse gases into the atmosphere are causing an anthropogenic climate change. The resulting global warming challenges the ability of organisms to adapt to the new temperature conditions. However, warming is not the only major threat. In marine environments, dissolution of carbon dioxide from the atmosphere causes a decrease in surface water pH, the so called ocean acidification. The temperature and acidification effects can interact, and create even larger problems for the marine flora and fauna than either of the effects would cause alone. I have used Baltic calanoid copepods (crustacean zooplankton) as my research object and studied their growth and stress responses using climate predictions projected for the next century. I have studied both direct temperature and pH effects on copepods, and indirect effects via their food: the changing phytoplankton spring bloom composition and toxic cyanobacterium. The main aims of my thesis were: 1) to find out how warming and acidification combined with a toxic cyanobacterium affect copepod reproductive success (egg production, egg viability, egg hatching success, offspring development) and oxidative balance (antioxidant capacity, oxidative damage), and 2) to reveal the possible food quality effects of spring phytoplankton bloom composition dominated by diatoms or dinoflagellates on reproducing copepods (egg production, egg hatching, RNA:DNA ratio). The two copepod genera used, Acartia sp. and Eurytemora affinis are the dominating mesozooplankton taxa (0.2 – 2 mm) in my study area the Gulf of Finland. The 20°C temperature seems to be within the tolerance limits of Acartia spp., because copepods can adapt to the temperature phenotypically by adjusting their body size. Copepods are also able to tolerate a pH decrease of 0.4 from present values, but the combination of warm water and decreased pH causes problems for them. In my studies, the copepod oxidative balance was negatively influenced by the interaction of these two environmental factors, and egg and nauplii production were lower at 20°C and lower pH, than at 20°C and ambient pH. However, presence of toxic cyanobacterium Nodularia spumigena improved the copepod oxidative balance and helped to resist the environmental stress, in question. In addition, adaptive maternal effects seem to be an important adaptation mechanism in a changing environment, but it depends on the condition of the female copepod and her diet how much she can invest in her offspring. I did not find systematic food quality difference between diatoms and dinoflagellates. There are both good and bad diatom and dinoflagellate species. Instead, the dominating species in the phytoplankton bloom composition has a central role in determining the food quality, although copepods aim at obtaining as a balanced diet as possible by foraging on several species. If the dominating species is of poor quality it can cause stress when ingested, or lead to non-optimal foraging if rejected. My thesis demonstrates that climate change induced water temperature and pH changes can cause problems to Baltic Sea copepod communities. However, their resilience depends substantially on their diet, and therefore the response of phytoplankton to the environmental changes. As copepods are an important link in pelagic food webs, their future success can have far reaching consequences, for example on fish stocks.

Fatigue study of the fillet weld waving on weld toe and the penetration in the weld root based on the effective notch stress approach

The fatigue failure of structures under fluctuating loads in fillet weld joints raises a demand to determine the parameters related to this type of loading. In this study, the stress distribution in the susceptible area of weld toe and weld root in fillet welded models analyzed by finite element method applying FEMAP software. To avoid the geometrical singularity on the path of analytical stress analysis in the toe and root area of a weld model the effective notch stress approach applied by which a proper fictitious rounding that mostly depend on the material of structure is applied. The models with different weld toe waving width and radius are analyzed while the flank angle of weld varied in 45 and 30 degrees. The processed results shows that the waving compare to the straight weld toe makes differences in the value of stress and consequently the stress concentration factor between the tip and depth of the waves in the weld toe which helps to protect the crack of propagation and gives enough time and tools to be informed of the crack initiation in the structure during the periodical observation of structure. In the weld root study the analyses among the models with the welding penetration percentage from non-penetration to the full-penetration shows a slightly increase in the root area stress value which comparing with the stiffening effect of penetration conclude that the half-penetration can make an optimization between the stress increase and stiffening effect of deep penetration.

Power cycling lifetime estimation of IGBT power modules based on chip temperature modeling

In this doctoral thesis, methods to estimate the expected power cycling life of power semiconductor modules based on chip temperature modeling are developed. Frequency converters operate under dynamic loads in most electric drives. The varying loads cause thermal expansion and contraction, which stresses the internal boundaries between the material layers in the power module. Eventually, the stress wears out the semiconductor modules. The wear-out cannot be detected by traditional temperature or current measurements inside the frequency converter. Therefore, it is important to develop a method to predict the end of the converter lifetime. The thesis concentrates on power-cycling-related failures of insulated gate bipolar transistors. Two types of power modules are discussed: a direct bonded copper (DBC) sandwich structure with and without a baseplate. Most common failure mechanisms are reviewed, and methods to improve the power cycling lifetime of the power modules are presented. Power cycling curves are determined for a module with a lead-free solder by accelerated power cycling tests. A lifetime model is selected and the parameters are updated based on the power cycling test results. According to the measurements, the factor of improvement in the power cycling lifetime of modern IGBT power modules is greater than 10 during the last decade. Also, it is noticed that a 10 C increase in the chip temperature cycle amplitude decreases the lifetime by 40%. A thermal model for the chip temperature estimation is developed. The model is based on power loss estimation of the chip from the output current of the frequency converter. The model is verified with a purpose-built test equipment, which allows simultaneous measurement and simulation of the chip temperature with an arbitrary load waveform. The measurement system is shown to be convenient for studying the thermal behavior of the chip. It is found that the thermal model has a 5 C accuracy in the temperature estimation. The temperature cycles that the power semiconductor chip has experienced are counted by the rainflow algorithm. The counted cycles are compared with the experimentally verified power cycling curves to estimate the life consumption based on the mission profile of the drive. The methods are validated by the lifetime estimation of a power module in a direct-driven wind turbine. The estimated lifetime of the IGBT power module in a direct-driven wind turbine is 15 000 years, if the turbine is located in south-eastern Finland.

Reliability of SMD interconnections on flexible low-temperature substrates with inkjet-printed conductors

julkaisumaa: NLD

Determinants of Polylepis (Rosaceae) Forest Distribution and Treeline Formation in the High Andes

High elevation treelines are formed under common temperature conditions worldwide, but the functional mechanisms that ultimately constrain tree growth are poorly known. In addition to environmental constraints, the distribution of high elevation forests is largely affected by human influence. Andean Polylepis (Rosaceae) forests are an example of such a case, forests commonly growing in isolated stands disconnected from the lower elevation montane forests. There has been ample discussion as to the role of environmental versus anthropogenic causes of this fragmented distribution of Polylepis forests, but the importance of different factors is still unclear. In this thesis, I studied functional, environmental and anthropogenic aspects determining Polylepis forest distribution. Specifically, I assessed the degree of genetic determinism in the functional traits that enable Polylepis species to grow in cold and dry conditions. I also studied the role of environment and human influence constraining Polylepis forest distribution. I found evidence of genetically determined climatic adaptations in the functional traits of Polylepis. High elevation species had reduced leaf size and increased root tip abundance compared to low elevation species. Thus these traits have potentially played an important role in species evolution and adaptation to high elevation habitats, especially to low temperatures. I also found reduced photosynthesis rate among high elevation tree species compared to low elevation species, supporting carbon source limitation at treelines. At low elevations, Polylepis forest distribution appeared to be largely defined by human influence. This suggests that the absence of Polylepis forests in large areas in the Andes is the result of several environmental and anthropogenic constraints, the role of environment becoming stronger towards high elevations. I also show that Polylepis trees grow at remarkably low air and soil temperatures near treelines, and present new evidence of the role of air temperatures in constraining tree growth at high elevations. I further show that easily measurable indices of accessibility are related to the degree of degradation of Polylepis forest, and can therefore be used in the rapid identification of potentially degraded Polylepis forests. This is of great importance for the conservation and restoration planning of Polylepis forests in the Andes. In a global context, the results of this thesis add to our scientific knowledge concerning high elevation adaptations in trees, and increase our understanding of the factors constraining tree growth and forest distribution at high-­elevation treelines worldwide.

Modeling of temperature regimes in a furnace of bubbling fluidized bed boiler

The work is mainly focused on the technology of bubbling fluidized bed combustion. Heat transfer and hydrodynamics of the process were examined in the work in detail. Special emphasis was placed on the process of heat exchange in a freeboard zone of bubbling fluidized bed boiler. Operating mode of bubbling fluidized bed boiler depends on many parameters. To assess the influence of some parameters on a temperature regime inside the furnace a simplified method of zonal modeling was used in the work. Thus, effects of bed material fineness, excess air ratio and changes in boiler load were studied. Besides the technology of combustion in bubbling fluidized bed, other common technologies of solid fuels combustion were reviewed. In addition, brief survey of most widely used types of solid fuel was performed in the work.

Track of HSMS Sophia tracing the extent of navigable water along the main northern ice between Spitzbergen and Greenland September 1868 : also showing the nature of the ice and temperature and depth of the sea

Kartta kuuluu A. E. Nordenskiöldin kokoelmaan

Bumblebees in a Changing Climate: Evaluating the Effects of Temperature on Queen Performance

Bumblebees are a very essential group of pollinating insects, but their populations have declined drastically during the past decades. We need to understand why their numbers are decreasing and what can be done to reverse this trend. Climate change-related phenomena, such as changes in the overwintering temperatures and spring conditions, are among the most prominent threats to bumblebees. Queens have a special role in the lifecycle of bumblebees because they overwinter and start new colonies the next year. Their successful performance: survival, overwintering ability, longevity, immune competence, and nest establishing capability in spring, is highly important for bumblebee populations. However, the effects of climate change on bumblebee queen performance remain unknown. The main objective of this thesis was to assess how temperature affects the performance of bumblebee queens during and after overwintering. The effects of warm temperature predicted by climate change scenarios on queen survival and stress-tolerance were studied by a four-month artificial diapause of bumblebee queens at two temperatures (9°C and 1.8°C). Bumblebee colonies were also reared in a laboratory and factors affecting colony characteristics were examined. In addition, queen performance during spring was studied in a starvation experiment using two temperatures (15°C as normal; 24°C as warmer than average) and queens collected from nature right after their emergence. My research revealed how temperature affects queen performance, and queen size was found to be an important factor determining the direction of some of these effects. We found a 0.4g weight threshold for bumblebee queens to be able to survive overwintering. In addition, during mild winters, larger queens have a higher chance than smaller ones to survive through winter and also to cope with immunological stresses after overwintering. During cold conditions, which are normal in the current climatic situation, this advantage disappears. In the spring starvation experiment, the starved queens survived approximately eight days longer in 15°C than in 24°C, which means that starvation risk rises significantly with increasing spring temperature, in a situation where food is scarce due to for example frost damage or asynchrony between bumblebees and their important food plants. These results could mean that in the future climate, larger queens are better able to survive the winter, initiate their nests and start rearing their offspring. This may be problematic, because I also detected two alternative strategies of colony development that differ between large and small queens; larger queens start to lay eggs earlier at nest initiation, their colonies mature later, they produce more workers, and they have a more strongly male biased sex allocation compared with smaller queens. If larger queens have a greater change of producing offspring after a mild winter, this could lead to a significant decline in the total production of new queens at a population level. Thus, it seems that queen size could act as one mechanism regulating the population level outcomes in different temperatures. The new information presented in my thesis reinforces that basic research, monitoring, and local species conservation of bumblebees both in Finland and globally must be increased to ensure that this highly important pollinator group survives in the face of climate change.