Dynamical and structural properties of dendrimer macromolecules

This work is devoted to the study of the dynamical and structural properties of dendrimers. Different approaches were used: analytical theory, computer simulation results and experimental NMR studies. The theory of the relaxation spectrum of dendrimer macromolecules was developed. Relaxation processes which are manifest in the local orientational mobility of dendrimer macromolecules were established and studied in detail. Theoretical results and conclusions were used for experimental studies of carbosilane dendimers.

Pallomaisen rullalaakerin vauriotutkimus kartonkikoneen kiertoöljyvoidellulla kuivatusosalla

Tämä työ on tehty Stora Enson Imatran kartonkitehtaan kunnossapidosta vastaavalle Efora Oy:lle. Tavoitteena oli selvittää syy Imatran Kartonkikone 5:n kuivatussylinterien laakerivaurioiden suureen määrään verrattuna tehtaiden kolmeen muuhun kartonkikoneeseen. Tutkimuksissa keskityttiin laakerien käyttöolosuhteisiin. Syyn selvittämiseksi työssä vertailtiin eri kartonkikoneiden kiertoöljyvoitelujärjestelmiä, voiteluöljyjä, voiteluolosuhteita, öljyjen kuntoa ja kunnon seurantaa. Myös laakereihin kohdistuvia kuormia arvioitiin. Alan kirjallisuuden avulla on käyty läpi kartonkikoneen rakennetta ja toimintaa tarvittavassa laajuudessa, voitelun ja laakerin vaurioitumisen teoriaa sekä voiteluaineiden ominaisuuksien ja koostumuksen perusteita. Vertailevissa tutkimuksissa ei löytynyt vauriomäärien eroja selittäviä eroavaisuuksia Imatran tehtaiden eri kartonkikoneiden välillä, joskin Kartonkikone 5:n kiertovoiteluöljyn puhtaustaso oli muita Imatran kartonkikoneita heikompi. Laakerikuormien osalta havaittiin joidenkin laakerien käyvän laakerille asetetun vähimmäiskuorman alittavilla kuormituksilla. Vähimmäiskuormaa pienempi radiaalikuorma voi johtaa laakerin virheelliseen toimintaan ja edelleen vaurioitumiseen. Voiteluolosuhteet todettiin erittäin vaikeiksi ja niillä on epäilemättä vaikutusta voiteluöljyn ja laakerien lyhentyneeseen käyttöikään.

Foot Health In Older People - Development of a preventive, evaluative instrument for nurses

Foot health is a part of overall health in every age group and its importance increases during ageing. Health care professionals are in a vital position for preventing foot health problems, and identifying and caring them in older people. Despite the rather high number of studies conducted in the field of foot health in older people, reliable and valid nurse-administered foot health assessment instruments seem to be lacking. By identifying foot health in older people, it is possible to develop nursing interventions to enhance safe, independent living at home. The purpose of this three-phase study was to develop an instrument to assess the level of foot health in older people and evaluate foot care practices from the perspective of older people themselves and nurses in home care. The ultimate goal is to prevent foot health problems by increasing the attention paid to older people’s feet and recognizing those foot health problems which need further care; thus not focus on different foot health problems. The study was conducted in different phases and contexts. In phase 1, a descriptive design with a literature review from the Medline (R) and CINAHL databases to explore foot health in older people and nurses’ role in foot health care and pre-post design intervention study in nursing home with nursing staff (n=16) and older residents (n=43) were conducted. In phase 2, a descriptive and explorative study design was employed to develop an instrument for assessing foot health in older people (N=651, n=309, response rate 47%) and explore the psychometrics of the instrument. The data were collected from sheltered housing and home care settings. Finally, in phase 3, descriptive and explorative as well as cross-sectional correlational survey designs were used to assess foot health and evaluate the foot self-care activities of older people (N=651, n=309, response rate 47%) and to describe foot care knowledge and caring activities of nurses (N=651, n=322, response rate 50%) in home care in Finland. To achieve this, the Foot Health Assessment Instrument (FHAI) developed in phase 2 was used; at the same time, this large sample also was used for the psychometric evaluation of the FHAI. The data analysis methods used in this study were content analysis, descriptive and inferential statistics including factor and multivariate analysis. Many long-term diseases can manifest in feet. Therefore, the FHAI, developed in this study consisted of items relating to skin and nail health, foot structure and foot pain. The FHAI demonstrated acceptable preliminary psychometric properties. A great deal of different foot health problems in older people were found of which edema, dry skin, thickened and discoloured toenails and hallux valgus were the most prevalent foot health problems. Moreover, many older people had difficulties in performing foot self-care. Nurses’ knowledge of foot care was insufficient and revealed a need for more information and continuing education in matters relating to foot care in older people. Instead, nurses’ foot care activities were mainly adequate, though the findings indicate the need for updating foot care activities to correspond with the evidence found in the field of foot care. Practical implications are presented for nursing practice, education and administration. In future, research should focus on developing interventions for older people and nurses to promote foot health in older people and to prevent foot health problems, as well as for further development of the FHAI.

Heat transfer inside internal combustion engine: modelling and comparison with experimental data

The paper is devoted to study specific aspects of heat transfer in the combustion chamber of compression ignited reciprocating internal combustion engines and possibility to directly measure the heat flux by means of Gradient Heat Flux Sensors (GHFS). A one – dimensional single zone model proposed by Kyung Tae Yun et al. and implemented with the aid of Matlab, was used to obtain approximate picture of heat flux behavior in the combustion chamber with relation to the crank angle. The model’s numerical output was compared to the experimental results. The experiment was accomplished by A. Mityakov at four stroke diesel engine Indenor XL4D. Local heat fluxes on the surface of cylinder head were measured with fast – response, high – sensitive GHFS. The comparison of numerical data with experimental results has revealed a small deviation in obtained heat flux values throughout the cycle and different behavior of heat flux curve after Top Dead Center.

Laser-TIG hybrid welding process

Joining processes and techniques need to meet the trend of new applications and the development of new materials. The application in connection with thick and thin plates in industrial fields is wide and the joining technology is in very urgent need. The laser-TIG hybrid welding technology can play the respective advantages of both of them. One major advantage of the hybrid laser-TIG welding technology is its efficient use of laser energy. Additionally, it can develop into a high and new advanced welding technology and become a hot spot in both the application and research area. This thesis investigated laser –TIG hybrid welding with the aim of enlightening the reader on its advantages, disadvantages and future areas of improvement. The main objective is to investigate laser-TIG hybrid on the welding of various metals (steels, magnesium, aluminium etc.). In addition, it elaborates on various possible combinations on hybrid laser-TIG welding technology and their benefits. The possibility of using laser-TIG hybrid in welding of thick materials was investigated. The method applied in carrying out this research is by using literature review. The results showed that hybrid laser-TIG is applicable to almost all weldable metals. Also it proves to be effective in welding refractive metals. The possibility of welding with or without filler materials is of economic advantage especially in welding of materials with no filler material. Thick plate’s hybrid laser-TIG welding is showing great prospects although it normally finds its used in welding thin materials in the range of 0.4 to 0.8 mm. The findings show that laser-TIG hybrid welding can be a versatile welding process and therefore will be increasingly used industrially due to its numerous advantages and the development of new TIG arc that enhances its capabilities.

Puristussylinterien valmistuksen kehittäminen

Tässä diplomityössä kehitettiin yksitoimisten puristussylinterien valmistusta Rautessa. Sylinterien valmistuksessa haastavin vaihe on sylinteriputken ja pohjan välinen hitsaus. Hitsauksen avuksi suunniteltiin sylinterin sisäpuolinen juuritukilaite. Hitsauskokeita suoritettiin hitsin pohjan jauhekaarihitsaukselle ja MAG-hitsaukselle. Juuritukilaitteen toimivuutta testattiin koehitsauksilla. Puristussylinterien materiaali on S355J2-terästä, jonka ainevahvuus on 20 – 60 mm. Paksujen rakenneterästen hitsauksessa täytyy ottaa huomioon hitsausliitoksen mekaanisten ominaisuuksien muuttuminen sekä eri halkeamien synty. Hitsauksen laatuun ja laadunhallintaan voidaan vaikuttaa monien eri tekijöiden avulla. Hitsausohjeen avulla, ja muut laatutekijät huomioiden, voidaan hitseille asetetut laatukriteerit täyttää. Juurituen käyttö nopeuttaa puristussylinterien hitsausta vähintään 50 %. Jauhekaarihitsaus kuparista juuritukea vasten synnyttää vaikeasti poistettavan kuonan juuren puolelle. Perinteinen MAG-hitsaus kuparista juuritukea vasten sisältää liian monta muuttujaa, mikä tekee siitä epäluotettavan pohjapalon hitsaukseen. Työssä suunnitellun juuritukilaitteen käyttö tuotannossa vaatii lisää hitsauskokeita.

Computational modeling of the properties of TiO2 nanoparticles

In this study we discuss the electronic, structural, and optical properties of titanium dioxide nanoparticles, and also the properties of Ni(II) diimine dithiolato complexes as dyes in dye-sensitized TiO2 based solar cells. The abovementioned properties have been modeled by using computational codes based on the density functional theory. The results achieved show slight evidence on the structure-dependent band gap broadening, and clear blue-shifts in absorption spectra and refractive index functions of ultra-small TiO2 particles. It is also shown that these properties are strongly dependent on the shape of the nanoparticles. Regarding the Ni(II) diimine dithiolato complexes as dyes in dye-sensitized TiO2 based solar cells, it is shown that based on the experimental electrochemical investigation and DFT studies all studied diimine derivatives could serve as potential candidates for the light harvesting, but the e ciencies of the dyes studied are not very promising.

Uraaniheksafluoridin faasimuutoksen CFD-mallinnus

Diplomityön tarkoituksena on luoda uraaniheksafluoridista käyttäjän määrittelemä aine kaupallisen virtauslaskentaohjelmiston (FLUENT) ainekirjastoon ja simuloida aineen käyttäytymistä sulaessa ja kiinteyttäessä. Työn kirjallisuusosassa on esitelty aiempia tutkimuksia uraaniheksafluoridin termodynaamisista ominaisuuksista, joita käytetään aineen määrittelyssä. Kokeellisessa osassa on käytetty virtauslaskentaohjelmiston Eulerilaista monifaasimallia sulamisen ja kiinteytymisen tarkasteluun kaksidimensionaalisessa sylinterissä.

Conventional and nonconventional Kramers-Kronig analysis in optical spectroscopy

This Master’s Thesis is dedicated to the investigation and testing conventional and nonconventional Kramers-Kronig relations on simulated and experimentally measured spectra. It is done for both linear and nonlinear optical spectral data. Big part of attention is paid to the new method of obtaining complex refractive index from a transmittance spectrum without direct information of the sample thickness. The latter method is coupled with terahertz tome-domain spectroscopy and Kramers-Kronig analysis applied for testing the validity of complex refractive index. In this research precision of data inversion is evaluated by root-mean square error. Testing of methods is made over different spectral range and implementation of this methods in future is considered.

Flexible multibody dynamics and intelligent control of a hydraulically driven hybrid redundant robot machine

The assembly and maintenance of the International Thermonuclear Experimental Reactor (ITER) vacuum vessel (VV) is highly challenging since the tasks performed by the robot involve welding, material handling, and machine cutting from inside the VV. The VV is made of stainless steel, which has poor machinability and tends to work harden very rapidly, and all the machining operations need to be carried out from inside of the ITER VV. A general industrial robot cannot be used due to its poor stiffness in the heavy duty machining process, and this will cause many problems, such as poor surface quality, tool damage, low accuracy. Therefore, one of the most suitable options should be a light weight mobile robot which is able to move around inside of the VV and perform different machining tasks by replacing different cutting tools. Reducing the mass of the robot manipulators offers many advantages: reduced material costs, reduced power consumption, the possibility of using smaller actuators, and a higher payload-to-robot weight ratio. Offsetting these advantages, the lighter weight robot is more flexible, which makes it more difficult to control. To achieve good machining surface quality, the tracking of the end effector must be accurate, and an accurate model for a more flexible robot must be constructed. This thesis studies the dynamics and control of a 10 degree-of-freedom (DOF) redundant hybrid robot (4-DOF serial mechanism and 6-DOF 6-UPS hexapod parallel mechanisms) hydraulically driven with flexible rods under the influence of machining forces. Firstly, the flexibility of the bodies is described using the floating frame of reference method (FFRF). A finite element model (FEM) provided the Craig-Bampton (CB) modes needed for the FFRF. A dynamic model of the system of six closed loop mechanisms was assembled using the constrained Lagrange equations and the Lagrange multiplier method. Subsequently, the reaction forces between the parallel and serial parts were used to study the dynamics of the serial robot. A PID control based on position predictions was implemented independently to control the hydraulic cylinders of the robot. Secondly, in machining, to achieve greater end effector trajectory tracking accuracy for surface quality, a robust control of the actuators for the flexible link has to be deduced. This thesis investigates the intelligent control of a hydraulically driven parallel robot part based on the dynamic model and two schemes of intelligent control for a hydraulically driven parallel mechanism based on the dynamic model: (1) a fuzzy-PID self-tuning controller composed of the conventional PID control and with fuzzy logic, and (2) adaptive neuro-fuzzy inference system-PID (ANFIS-PID) self-tuning of the gains of the PID controller, which are implemented independently to control each hydraulic cylinder of the parallel mechanism based on rod length predictions. The serial component of the hybrid robot can be analyzed using the equilibrium of reaction forces at the universal joint connections of the hexa-element. To achieve precise positional control of the end effector for maximum precision machining, the hydraulic cylinder should be controlled to hold the hexa-element. Thirdly, a finite element approach of multibody systems using the Special Euclidean group SE(3) framework is presented for a parallel mechanism with flexible piston rods under the influence of machining forces. The flexibility of the bodies is described using the nonlinear interpolation method with an exponential map. The equations of motion take the form of a differential algebraic equation on a Lie group, which is solved using a Lie group time integration scheme. The method relies on the local description of motions, so that it provides a singularity-free formulation, and no parameterization of the nodal variables needs to be introduced. The flexible slider constraint is formulated using a Lie group and used for modeling a flexible rod sliding inside a cylinder. The dynamic model of the system of six closed loop mechanisms was assembled using Hamilton’s principle and the Lagrange multiplier method. A linearized hydraulic control system based on rod length predictions was implemented independently to control the hydraulic cylinders. Consequently, the results of the simulations demonstrating the behavior of the robot machine are presented for each case study. In conclusion, this thesis studies the dynamic analysis of a special hybrid (serialparallel) robot for the above-mentioned special task involving the ITER and investigates different control algorithms that can significantly improve machining performance. These analyses and results provide valuable insight into the design and control of the parallel robot with flexible rods.

Simulation of the Interaction Mean Free Path between Neutrons and TRISO Particles

The interaction mean free path between neutrons and TRISO particles is simulated using scripts written in MATLAB to solve the increasing error present with an increase in the packing factor in the reactor physics code Serpent. Their movement is tracked both in an unbounded and in a bounded space. Their track is calculated, depending on the program, linearly directly using the position vectors of the neutrons and the surface equations of all the fuel particles; by dividing the space in multiple subspaces, each of which contain a fraction of the total number of particles, and choosing the particles from those subspaces through which the neutron passes through; or by choosing the particles that lie within an infinite cylinder formed on the movement axis of the neutron. The estimate from the current analytical model, based on an exponential distribution, for the mean free path, utilized by Serpent, is used as a reference result. The results from the implicit model in Serpent imply a too long mean free path with high packing factors. The received results support this observation by producing, with a packing factor of 17 %, approximately 2.46 % shorter mean free path compared to the reference model. This is supported by the packing factor experienced by the neutron, the simulation of which resulted in a 17.29 % packing factor. It was also observed that the neutrons leaving from the surfaces of the fuel particles, in contrast to those starting inside the moderator, do not follow the exponential distribution. The current model, as it is, is thus not valid in the determination of the free path lengths of the neutrons.

Defining the keyhole modes – the effects on the weld geometry and the molten pool behaviour in high power laser welding of stainless steels

Keyhole welding, meaning that the laser beam forms a vapour cavity inside the steel, is one of the two types of laser welding processes and currently it is used in few industrial applications. Modern high power solid state lasers are becoming more used generally, but not all process fundamentals and phenomena of the process are well known and understanding of these helps to improve quality of final products. This study concentrates on the process fundamentals and the behaviour of the keyhole welding process by the means of real time high speed x-ray videography. One of the problem areas in laser welding has been mixing of the filler wire into the weld; the phenomena are explained and also one possible solution for this problem is presented in this study. The argument of this thesis is that the keyhole laser welding process has three keyhole modes that behave differently. These modes are trap, cylinder and kaleidoscope. Two of these have sub-modes, in which the keyhole behaves similarly but the molten pool changes behaviour and geometry of the resulting weld is different. X-ray videography was used to visualize the actual keyhole side view profile during the welding process. Several methods were applied to analyse and compile high speed x-ray video data to achieve a clearer image of the keyhole side view. Averaging was used to measure the keyhole side view outline, which was used to reconstruct a 3D-model of the actual keyhole. This 3D-model was taken as basis for calculation of the vapour volume inside of the keyhole for each laser parameter combination and joint geometry. Four different joint geometries were tested, partial penetration bead on plate and I-butt joint and full penetration bead on plate and I-butt joint. The comparison was performed with selected pairs and also compared all combinations together.

Talo, kartano, puutarha. Kauppahuoneen omistaja Marie Hackman ja hänen kulutusvalintansa varhaismodernissa Viipurissa

Tutkimuksessa keskitytään tutkimaan kuluttamista elämäntavan ja identiteetin muovaajana yhden yksilön elämän kautta. Kuluttamista tutkitaan statuskuluttamisen (conspicious consumption), tilallisuuden ja sukupuolihistorian käsitteistöä hyväksi käyttäen. Tutkimuksen lähteinä on käytetty liikekirjeitä ja tilikirjoja, yksityistä kirjeenvaihtoa, päiväkirjoja ja sanomalehtiä sekä aikalaismuistelmia. Naista lähdemateriaaleista on koottu sekä tilastollista aineistoa että kvalitatiivista, lähilukuun ja mikrohistorialliseen tutkimusotteeseen nojautuvaa tutkimusta. Tutkimus alkaa vuodesta 1799 ja päättyy 1830-luvulle, jolloin seuraava sukupolvi otti vastuun liiketoimista ja lähdeaineistossa tapahtui muutoksia kuluttamisen kirjaamisen suhteen. Tutkimuksen keskeiset käsitteet ovat statuskuluttaminen ja identiteetti. Näitä käsitteitä lähestytään Thorstein Veblenin, Norbert Eliaksen ja Pierre Bourdieun tutkimuksia apuna käyttäen. Tutkimus käsittelee erottautumisen ja jäljittelyn tematiikkaa merkittävimpänä kuluttamisen motivaattoreina. Lisaksi tutkimus nostaa esille hyvän maun ja muodinmukaisuuden kulutusvalintojen taustalla. Statuskuluttaminen kytkeytyy sosiaaliseen kanssakäymiseen. Kuluttamisen kohteet ovat esineitä ja asioita, joita pidetään esillä seurapiireissä. Kuluttaminen tapahtuu seuraelämän ehdoilla, sen mukavoittamiseksi, aseman osoittamiseksi seurapiireissä tai sosiaalisen paineen vuoksi. Tutkimus osoittaa kotitalouden merkityksen kuluttamisen paikkana ja kohteena. Tutkimus myös osoittaa naisten toimintakentän olleen kytköksissä kotitalouden asemaan yhteisössään sekä osoittaa, että sukupuolta pitää tarkastella suhteessa yksilön sosiaaliseen asemaan. Tutkimus osoittaa, että Marie Hackmanin kuluttaminen muuttui ikääntymisen myötä. Aseman osoittaminen oli merkittävämpää nuorena ja aseman ollessa vielä vakiintumattomampi.

Computational studies of deformation in stainless steel rings due to torch heating

A support ring of AISI 304L stainless steel that holds vertical, parallel wires arranged in a circle forming a cylinder is studied. The wires are attached to the ring with heat-induced shrinkage. When the ring is heated with a torch the heat affected zone tries to expand while the adjacent cool structure obstructs the expansion causing upsetting. During cooling, the ring shrinks smaller than its original size clamping the wires. The most important requirement for the ring is that it should be as round as possible and the deformations should occur as overall shrinkage in the ring diameter. A three-dimensional nonlinear transient sequential thermo-structural Abaqus model is used together with a Fortran code that enters the heat flux to each affected element. The local and overall deformations in one ring inflicted by the heating are studied with a small amount of inspection on residual stresses. A variety of different cases are chosen to be studied with the model constructed to provide directional knowledge; torch flux with the means of speed, location of the wires, heating location and structural factors. The decrease of heating speed increases heat flux that rises the temperature increasing shrinkage. In a single progressive heating uneven distribution of shrinkage appears to the start/end region that can be partially fixed with using speeded heating’s to strengthen the heating of that region. Location of the wires affect greatly to the caused shrinkage unlike heating location. The ring structure affects also greatly to the shrinkage; smaller diameter, bigger ring height, thinner thickness and greater number of wires increase shrinkage.

Modelling Cutting States in Rough Turning of 34CrNiMo6 Steel

Rough turning is an important form of manufacturing cylinder-symmetric parts. Thus far, increasing the level of automation in rough turning has included process monitoring methods or adaptive turning control methods that aim to keep the process conditions constant. However, in order to improve process safety, quality and efficiency, an adaptive turning control should be transformed into an intelligent machining system optimizing cutting values to match process conditions or to actively seek to improve process conditions. In this study, primary and secondary chatter and chip formation are studied to understand how to measure the effect of these phenomena to the process conditions and how to avoid undesired cutting conditions. The concept of cutting state is used to address the combination of these phenomena and the current use of the power capacity of the lathe. The measures to the phenomena are not developed based on physical measures, but instead, the severity of the measures is modelled against expert opinion. Based on the concept of cutting state, an expert system style fuzzy control system capable of optimizing the cutting process was created. Important aspects of the system include the capability to adapt to several cutting phenomena appearing at once, even if the said phenomena would potentially require conflicting control action.