Validation of plant dynamic model by online and laboratory measurements – a tool to predict online COD loads out of production of mechanical printing papers

COD discharges out of processes have increased in line with elevating brightness demands for mechanical pulp and papers. The share of lignin-like substances in COD discharges is on average 75%. In this thesis, a plant dynamic model was created and validated as a means to predict COD loading and discharges out of a mill. The assays were carried out in one paper mill integrate producing mechanical printing papers. The objective in the modeling of plant dynamics was to predict day averages of COD load and discharges out of mills. This means that online data, like 1) the level of large storage towers of pulp and white water 2) pulp dosages, 3) production rates and 4) internal white water flows and discharges were used to create transients into the balances of solids and white water, referred to as “plant dynamics”. A conversion coefficient was verified between TOC and COD. The conversion coefficient was used for predicting the flows from TOC to COD to the waste water treatment plant. The COD load was modeled with similar uncertainty as in reference TOC sampling. The water balance of waste water treatment was validated by the reference concentration of COD. The difference of COD predictions against references was within the same deviation of TOC-predictions. The modeled yield losses and retention values of TOC in pulping and bleaching processes and the modeled fixing of colloidal TOC to solids between the pulping plant and the aeration basin in the waste water treatment plant were similar to references presented in literature. The valid water balances of the waste water treatment plant and the reduction model of lignin-like substances produced a valid prediction of COD discharges out of the mill. A 30% increase in the release of lignin-like substances in the form of production problems was observed in pulping and bleaching processes. The same increase was observed in COD discharges out of waste water treatment. In the prediction of annual COD discharge, it was noticed that the reduction of lignin has a wide deviation from year to year and from one mill to another. This made it difficult to compare the parameters of COD discharges validated in plant dynamic simulation with another mill producing mechanical printing papers. However, a trend of moving from unbleached towards high-brightness TMP in COD discharges was valid.

Development of a Filter Aid Proportioning, Mixing, and Feeding System for a Polishing Filter

The purpose of this work was to study the characteristics of the most commonly used filter aid materials and their influences on the design of proportioning, mixing, and feeding system for polishing filter family. Based on the literature survey and hands-on experience a system was designed with defined equipment and capital and operating costs. The system was designed to serve precoating and bodyfeeding applications and is easily extended to be used in multiple filter processes. Also a test procedure was carried out where influences of flux and filter cloths to accumulated cake were studied. Filter aid is needed in challenging conditions to improve filtration efficiency and cleaning, and thus extend the operating life of the filter media. Filter aid preparation and feeding system was designed for the use of two different filter aids; precoat and bodyfeed. Precoating is used before the filtration step initiates. If the solids in the filterable solution have a tendency to clog the filter bag easily, precoat is used on the filter bag to obtain better filtration efficiency and quality. Diatomite or perlite is usually used as a precoating substance. The intention is to create a uniform cake to the overall surface of the filter cloth, with predetermined thickness, 2 – 5 mm. This ensures that the clogging of the filter cloth is reduced and the filtration efficiency is increased. Bodyfeed is used if the solids in the filterable solution have a tendency to form a sticky impermeable filter cake. The cake properties are enhanced by maintaining the permeability of the accumulating cake by using the filter aid substance as bodyfeed during the filtration process.

Offdesign operation of kraft recovery boiler

A model to solve heat and mass balances during the offdesign load calculations was created. These equations are complex and nonlinear. The main new ideas used in the created offdesign model of a kraft recovery boiler are the use of heat flows as torn iteration variables instead of the current practice of using the mass flows, vectorizing equation solving, thus speeding up the process, using non dimensional variables for solving the multiple heat transfer surface problem and using a new procedure for calculating pressure losses. Recovery boiler heat and mass balances are reduced to vector form. It is shown that these vectorized equations can be solved virtually without iteration. The iteration speed is enhanced by the use of the derived method of calculating multiple heat transfer surfaces simultaneously. To achieve this quick convergence the heat flows were used as the torn iteration parameters. A new method to handle pressure loss calculations with linearization was presented. This method enabled less time to be spent calculating pressure losses. The derived vector representation of the steam generator was used to calculate offdesign operation parameters for a 3000 tds/d example recovery boiler. The model was used to study recovery boiler part load operation and the effect of the black liquor dry solids increase on recovery boiler dimensioning. Heat flows to surface elements for part load calculations can be closely approximated with a previously defined exponent function. The exponential method can be used for the prediction of fouling in kraft recovery boilers. For similar furnaces the firing of 80 % dry solids liquor produces lower hearth heat release rate than the 65 % dry solids liquor if we fire at constant steam flow. The furnace outlet temperatures show that capacity increase with firing rate increase produces higher loadings than capacity increase with dry solids increase. The economizers, boiler banks and furnaces can be dimensioned smaller if we increase the black liquor dry solids content. The main problem with increased black liquor dry solids content is the decrease in the heat available to superheat. Whenever possible the furnace exit temperature should be increased by decreasing the furnace height. The increase in the furnace exit temperature is usually opposed because of fear of increased corrosion.

Active sulphide mine tailings impoundments as sources of contaminated drainage: controlling factors, methods of characterisation and geochemical constraints for mitigation

Low quality mine drainage from tailings facilities persists as one of the most significant global environmental concerns related to sulphide mining. Due to the large variation in geological and environmental conditions at mine sites, universal approaches to the management of mine drainage are not always applicable. Instead, site-specific knowledge of the geochemical behaviour of waste materials is required for the design and closure of the facilities. In this thesis, tailings-derived water contamination and factors causing the pollution were investigated in two coeval active sulphide mine sites in Finland: the Hitura Ni mine and the Luikonlahti Cu-Zn-Co-Ni mine and talc processing plant. A hydrogeochemical study was performed to characterise the tailingsderived water pollution at Hitura. Geochemical changes in the Hitura tailings were evaluated with a detailed mineralogical and geochemical investigation (solid-phase speciation, acid mine drainage potential, pore water chemistry) and using a spatial assessment to identify the mechanisms of water contamination. A similar spatial investigation, applying selective extractions, was carried out in the Luikonlahti tailings area for comparative purposes (Hitura low-sulphide tailings vs. Luikonlahti sulphide-rich tailings). At both sites, hydrogeochemistry of tailings seepage waters was further characterised to examine the net results of the processes observed within the impoundments and to identify constraints for water treatment. At Luikonlahti, annual and seasonal variation in effluent quality was evaluated based on a four-year monitoring period. Observations pertinent to future assessment and mine drainage prevention from existing and future tailings facilities were presented based on the results. A combination of hydrogeochemical approaches provided a means to delineate the tailings-derived neutral mine drainage at Hitura. Tailings effluents with elevated Ni, SO₄ ^2- and Fe content had dispersed to the surrounding aquifer through a levelled-out esker and underneath the seepage collection ditches. In future mines, this could be avoided with additional basal liners in tailings impoundments where the permeability of the underlying Quaternary deposits is inadequate, and with sufficiently deep ditches. Based on the studies, extensive sulphide oxidation with subsequent metal release may already initiate during active tailings disposal. The intensity and onset of oxidation depended on e.g. the Fe sulphide content of the tailings, water saturation level, and time of exposure of fresh sulphide grains. Continuous disposal decreased sulphide weathering in the surface of low-sulphide tailings, but oxidation initiated if they were left uncovered after disposal ceased. In the sulphide-rich tailings, delayed burial of the unsaturated tailings had resulted in thick oxidized layers, despite the continuous operation. Sulphide weathering and contaminant release occurred also in the border zones. Based on the results, the prevention of sulphide oxidation should already be considered in the planning of tailings disposal, taking into account the border zones. Moreover, even lowsulphide tailings should be covered without delay after active disposal ceases. The quality of tailings effluents showed wide variation within a single impoundment and between the two different types of tailings facilities assessed. The affecting factors included source materials, the intensity of weathering of tailings and embankment materials along the seepage flow path, inputs from the process waters, the water retention time in tailings, and climatic seasonality. In addition, modifications to the tailings impoundment may markedly change the effluent quality. The wide variation in the tailings effluent quality poses challenges for treatment design. The final decision on water management requires quantification of the spatial and seasonal fluctuation at the site, taking into account changes resulting from the eventual closure of the impoundment. Overall, comprehensive hydrogeochemical mapping was deemed essential in the identification of critical contaminants and their sources at mine sites. Mineralogical analysis, selective extractions, and pore water analysis were a good combination of methods for studying the weathering of tailings and in evaluating metal mobility from the facilities. Selective extractions with visual observations and pH measurements of tailings solids were, nevertheless, adequate in describing the spatial distribution of sulphide oxidation in tailings impoundments. Seepage water chemistry provided additional data on geochemical processes in tailings and was necessary for defining constraints for water treatment.

Happaman hydrometallurgisen PLS-liuoksen puhdistaminen kiintoaineesta kalvosuodatustekniikalla

Tässä diplomityössä tutkittiin keraamisten mikrosuodatuskalvojen soveltuvuutta kiintoaineen erottamiseen happamasta PLS-liuoksesta eri huokoskoon omaavilla mikrosuodatuskalvoilla. Koelaitteistolla suodatettiin puhdasta vettä, kaoliinipitoista vesiliuosta sekä hapanta kuparia, kalsiumia ja kaoliinia sisältävää malliliuosta. Koeajojen tavoitteena oli saada tietoa permeaattivuon maksimimäärästä eri mikrosuodatuskalvoilla sekä tuotteen puhtaudesta. Näiden lisäksi saatiin tietoa kalvojen likaantumisesta ajon aikana. Teoriaosassa käsiteltiin yleisesti kalvosuodatusta, esitettiin yleiset kalvotekniset menetelmät ja sovellukset sekä käytiin läpi tutkimuksia samankaltaisiin kalvoihin ja sovelluksiin liittyen. Lisäksi teoriaosuudessa pohdittiin mahdollisuutta käyttää myös muita, kuin putkimoduulisia mikrosuodatuskalvoja. Myös työhön oleellisena taustana kuuluvaa hydrometallurgiaa tarkasteltiin teoreettiselta kannalta. Puhtaan veden suodatuskoetuloksista havaittiin, että kaikki kalvot jäivät selvästi valmistajan ilmoittamista arvoista. 1,0 µm CoMetas CoMem® kalvon teoreettinen vesivuo on 10 m3/(h bar) ja 3,0 µm CoMetas CoMem® teoreettinen vesivuo on yli 50 m3/(h bar). Näistä parhaimman vuon arvon sai 1,0 µm CoMetas CoMem® mikrosuodatuskalvo. Tämä kalvo oli paras sekä veden suodatuksissa että malliliuoksella tehdyillä suodatuksilla. Malliliuoksella saavutettiin n. 2000 L/(m2 h) paineen ollessa 2,0 bar ja virtausnopeuden ollessa 4,4 m/s. Vastaavat vesiajon tulokset olivat n. 1100 L/(m2 h) paineen ollessa 1,0 bar ja virtausnopeuden 2,9 m/s. Kaikki kolme käytettyä kalvoa pidättivät kaoliiniliuoksen 81–100 %:sesti. Kuparipitoista malliliuosta suodatettaessa pystyttiin vastaavasti erottamaan 77–99 % kiintoaineesta. Koeajoissa kuitenkin havaittiin huomattava vuon arvojen putoaminen, joka johtui kalvon likaantumisesta. Huomioitavaa oli kuitenkin, että hapanta malliliuosta suodatettaessa permeaattivuon arvot olivat kaoliiniliuoksen suodatuksessa saatuja vastaavia arvoja korkeammat.

Counselling on limited preoperative fasting in paediatric ambulatory tonsillectomy

Rajoitetun preoperatiivisen paaston ohjaus lasten päiväkirurgisessa nielurisaleikkauksessa Tutkimuksen tarkoituksena oli selvittää, onko sairaanhoitajan toteuttama, vanhempien interaktiivinen preoperatiivinen ohjaus lapsen rajoitettuun preoperatiiviseen paastoon ja aktiiviseen nesteyttämiseen turvallista, kuinka vanhemmat omaksuvat kyseistä tietoa ja edistääkö se turvallisesti lapsen postoperatiivista toipumista päiväkirurgisen nielurisaleikkauksen jälkeen. Aineisto koostui sadastakuudestatoista perheestä, joiden lapsi, iältään 4 – 10 vuotta, oli kutsuttu päiväkirurgiseen nielurisaleikkaukseen. Koeryhmä (n= 58) ohjattiin interaktiivisesti lapsen preoperatiiviseen paastoon ja aktiiviseen preoperatiiviseen nesteyttämiseen. Lapsen suositellut preoperatiiviset paastoajat olivat: 4t syömättä ja 2t juomatta. Leikkauspäivän aamuna vanhemmat rohkaisivat lapsia juomaan annokset kirkkaita nesteitä kahteen otteeseen; jälkimmäinen annos 2t ennen leikkausta. Kontrolliryhmä (n= 58) sai preoperatiivisen ohjauksen kirjallisena ilman interaktiivista ohjausta; paastoajat olivat samat kuin koeryhmässä: 4t syömättä ja 2t juomatta. Vanhempien tiedontasoa lapsen leikkaukseen liittyvästä paastosta mitattiin tietotestillä, joka sisälsi myös preoperatiivista tiedontarvetta ja ahdistusta mittaavan mittarin (The Amsterdam Preoperative Anxiety and Information scale, APAIS). Mittaukset suoritettiin ennen preoperatiivista ohjausta tai kirjallisten ohjeiden lähettämistä sekä lapsen leikkausta seuraavana päivänä. Lapsen leikkauksen jälkeen vanhemmat arvioivat myös heille välitetyn informaation tasoa. Lapsen postoperatiivista kipua, pahoinvointia, janoa ja nälkää lapset itse arvioivat VAS- asteikolla (10cm), ja vanhemmat ja sairaanhoitajat numeerisella 0 – 10 asteikolla. Mittaukset suoritettiin 2t, 4t, 8t, ja 24t lapsen leikkauksen jälkeen. Vanhemmat pitivät päiväkirjaa lapsen ravinnosta ja kipulääkityksestä. Aineisto analysoitiin sekä tilastollisesti että sisällön analyysilla. Vanhempien tiedontaso lapsen leikkauksen jälkeen oli molemmissa ryhmissä merkitsevästi parantunut, mutta kontrolliryhmän vanhempien ahdistus ei ollut helpottanut verrattuna heidän ahdistukseensa ennen lapsen leikkausta. Mitä korkeammat pisteet vanhemmat saivat tietotestistä lapsen leikkauksen jälkeen sitä vähemmän he tunsivat tiedontarvetta ja ahdistusta. Merkitsevästi alhaisemmat pisteet tietotestistä oli vanhemmilla, joilla oli alempi peruskoulutus. Kontrolliryhmän lapset paastosivat preoperatiivisesti merkitsevästi pitempään kuin koeryhmän lapset. Perioperatiivisesti lapset paastosivat kiinteästä ruuasta yhtä kauan, mutta nesteistä kontrolliryhmä merkitsevästi pitempään. Postoperatiivisen toipumisen alussa koeryhmän lapset olivat merkitsevästi kivuttomampia. Molemmissa ryhmissä lapset olivat kipeimpiä kahdeksan tuntia leikkauksesta ja pahoinvointisimpia neljä tuntia leikkauksesta. Ensimmäisen kahdeksan tunnin aikana leikkauksen jälkeen lapset eivät olleet janoisia tai nälkäisiä, mutta VAS- arvot koeryhmässä jäivät alhaisemmalle tasolle kuin kontrolliryhmässä 24 postoperatiivisen tunnin ajan. Leikkausta seuraavana aamuna kontrolliryhmän lapset olivat merkitsevästi janoisempia ja nälkäisempiä kuin interventioryhmän lapset. Sairaanhoitajan toteuttama vanhempien interaktiivinen preoperatiivinen ohjaus lapsen rajoitettuun preoperatiiviseen paastoon lisää vanhempien tiedontasoa ja vähentää preoperatiivista tiedontarvettaan ja ahdistusta, ja turvallisesti parantaa lapsen kokemusta leikkausprosessin ja postoperatiivisen toipumisen aikana nielurisaleikkauksen jälkeen. Kaikkien leikkaukseen tulevien lasten nesteyttäminen kaksi tuntia ennen päivän ensimmäistä leikkausta voi olla ratkaisu lasten kohtuuttomien perioperatiivisten paastoaikojen estämiseksi. Aina ei kuitenkaan ole mahdollisuuksia vanhempien henkilökohtaiseen kohtaamiseen, mikä haastaa hoitotieteellisen tutkimuksen kartoittamaan muita mahdollisuuksia vanhempien interaktiiviseen ohjaukseen.

Measurement and Improvement of Wet Paper Web Strength

Various strength properties of paper are measured to tell how well it resists breaks in a paper machine or in printing presses. The most often measured properties are dry tensile strength and dry tear strength. However, in many situations where paper breaks, it is not dry. For example, in web breaks after the wet pressing the dry matter content can be around 45%. Thus, wet-web strength is often a more critical paper property than dry strength. Both wet and dry strength properties of the samples were measured with a L&W tensile tester. Originally this device was not designed for the measurement of the wet web tensile strength, thus a new procedure to handle the wet samples was developed. The method was tested with Pine Kraft (never dried). The effect of different strength additives on the wet-web and dry paper tensile strength was studied. The polymers used in this experiment were aqueous solution of a cationic polyamidoamine-epichlorohydrin resin (PAE), cationic hydrophilised polyisocyanate and cationic polyvinylamine (PVAm). From all three used chemicals only Cationic PAE considerably increased the wet web strength. However it was noticed that at constant solids content all chemicals decreased the wet web tensile strength. So, since all chemicals enhanced solid content it can be concluded that they work as drainage aids, not as wet web strength additives. From all chemicals only PVAm increased the dry strength and two other chemicals even decreased the strength. As chemicals were used in strong diluted forms and were injected into the pulp slurry, not on the surface of the papersheets, changes in samples densities did not happen. Also it has to be noted that all these chemicals are mainly used to improve the wet strength after the drying of the web.

Design of Installation for Transport Measurements

In the present work the aim was to prepare an automatic installation for studies of galvanomagnetic effects in solids and to test it by calibration measurements. As a result required automatic installation was created in this work and test measurements were performed. Created setup automatically provides measurements of the magnetoresistance of the Hall effect with an accuracy of ± 2 µV in the temperature range 2 – 300 K and steady magnetic fields up to 6 T. The test measurements of the glassy carbon samples showed that the setup is reliable, has high sensitivity and is easy to use. The results obtained in the research process are pioneer and will be separately analyzed.

Puulevystä valmistettujen kalusteosien pintakäsittelyn kehittäminen UV-telalinjalla

Diplomityö tehtiin Kidex Oy:lle, joka on Kiteellä sijaitseva Martela-konsernin tytäryhtiö. Kidex Oy toimii sopimusvalmistajana Martelalle sekä muille valituille levykalusteasiakkaille, ja tuotteet ovat pääasiassa toimisto- ja keittiökalusteita. Kevättalvella 2008 yritykseen siirrettiin Nummelasta pintakäsittelyosasto, jolla on tehty petsaus- ja lakkaustöitä. Näiden lisäksi tehtaalla on pohdittu mahdollisuuksia maalaustöihin, jotta UV-telalinjan kapasiteetti saataisiin paremmin käyttöön Työssä selvitettiin, mitä muutoksia UV-kovettuvilla aineilla maalaaminen vaatii linjaan ja luotiin edellytykset maalaustoiminnan aloittamiselle. Muutokset pyrittiin pitämään niin vähäisinä kuin mahdollista. Lisäksi määritettiin maalattavien tuotteiden laadun kriteerit ja todennusmenetelmät, jotka voidaan viestiä asiakkaille väärinkäsitysten välttämiseksi. Laadun todentamista varten valmistettiin sarja koekappaleita, joista mitattiin asiakkaan kannalta tärkeimmät maalikalvon ominaisuudet. Työssä tarkasteltiin myös pintakäsittelylaitoksia koskevaa VOC-asetusta ja verrattiin liuottimien kulutusta asetuksen määrittämiin rajoihin. Puulevystä valmistettujen kalusteosien pintakäsittely UV-telalinjalla eroaa oleellisesti perinteisistä menetelmistä esimerkiksi tuotantonopeuden osalta, joka johtuu pääasiassa pinnoitekalvon hetkessä tapahtuvasta kovettumisesta UV-valon vaikutuksesta. UV-aineet ovat käytännössä täysin kiinteistä aineista koostuvia, eivätkä näin sisällä vaarallisia haihtuvia liuottimia. UV-kovettuvilla tuotteilla maalaaminen on viime vuosina runsaasti tutkittu alue, joka eroaa tietyiltä osin myös pintakäsittelystä UV-kirkaslakoilla. Pigmentoitujen kalvojen kovettuminen vaatii erilaista UV-säteilyä ja levitysmäärien seuranta on huomattavasti tarkempaa.

CFD Simulation of Two-phase and Three-phase Flows in Internal-loop Airlift

Airlift reactors are pneumatically agitated reactors that have been widely used in chemical, petrochemical, and bioprocess industries, such as fermentation and wastewater treatment. Computational Fluid Dynamics (CFD) has become more popular approach for design, scale-up and performance evaluation of such reactors. In the present work numerical simulations for internal-loop airlift reactors were performed using the transient Eulerian model with CFD package, ANSYS Fluent 12.1. The turbulence in the liquid phase is described using κ- ε the model. Global hydrodynamic parameters like gas holdup, gas velocity and liquid velocity have been investigated for a range of superficial gas velocities, both with 2D and 3D simulations. Moreover, the study of geometry and scale influence on the reactor have been considered. The results suggest that both, geometry and scale have significant effects on the hydrodynamic parameters, which may have substantial effects on the reactor performance. Grid refinement and time-step size effect have been discussed. Numerical calculations with gas-liquid-solid three-phase flow system have been carried out to investigate the effect of solid loading, solid particle size and solid density on the hydrodynamic characteristics of internal loop airlift reactor with different superficial gas velocities. It was observed that averaged gas holdup is significantly decreased with increasing slurry concentration. Simulations show that the riser gas holdup decreases with increase in solid particle diameter. In addition, it was found that the averaged solid holdup increases in the riser section with the increase of solid density. These produced results reveal that CFD have excellent potential to simulate two-phase and three-phase flow system.

Täyteaineen dispergoinnin vaikutus paperin ominaisuuksiin

Kuljetettaessa täyteainetta pidempiä matkoja voidaan aikaan saada säästöjä, mikäli täyteaineliete valmistetaan korkeaan kuiva-ainepitoisuuteen. Dispergointiaineen avulla täyteainelietteen kuiva-ainepitoisuutta voidaan nostaa ilman, että menetetään täyteainelietteen virtausominaisuuksia. Dispergointiaineen tehtävänä on stabiloida täyteaineliete niin, että täyteainepartikkelit pysyvät lietteessä erillään, jolloin lietteen kuiva-ainepitoisuuden kasvattaminen on mahdollista. Täyteainepartikkelien agglomeroituminen estyy, kun dispergointiaine kiinnittyy täyteainepartikkelin pinnalle lisäten partikkelin sähkövarausta ja vahvistaen näin partikkeleiden välisiä repulsiovoimia. Dispergointi on mahdollista tehdä myös steerisellä stabiloinnilla. Yleisimmät käytössä olevat dispergointiaineet ovat polyakryylaatteja. Työssä tutkittiin MBF- laitteella valmistettujen arkkien avulla dispergoinnin vaikutusta täyteaineiden käyttäytymiseen ja paperin ominaisuuksiin. Dispergointiaineen todettiin heikentävän täyteaineen retentiota paperiin, sillä dispergointiaineen aiheuttama täyteaineen anionisuuden kasvu lisää kuidun ja täyteaineen välistä repulsiota. Dispergoitujen täyteaineiden käyttö vaatii retentioaineannoksen kasvattamista, mikä voi johtaa puolestaan formaation heikkenemiseen. Dispergointiaineen todettiin alentavan hienopaperin bulkkia, sillä paksuutta lisääviä agglomeraatteja esiintyi todennäköisesti vähemmän. Lisäksi dispergointiaineen havaittiin heikentävän hienopaperin ja TMP:stä valmistetun paperin optisia ominaisuuksia. Hienopaperilla dispergointiaineen käyttö puolestaan paransi paperin lujuusominaisuuksia. TMP- arkeilla bulkki ja lujuusominaisuudet muuttuivat dispergointiaineannostuksen myötä. 5 ‰:n dispergointiaineannostuksella päästiin samaan bulkkiin sekä lujuusominaisuuksiin kuin ei-dispergoidulla täyteaineella.

Computational Evaluation of Print Unevenness According to Human Vision

Print quality and the printability of paper are very important attributes when modern printing applications are considered. In prints containing images, high print quality is a basic requirement. Tone unevenness and non uniform glossiness of printed products are the most disturbing factors influencing overall print quality. These defects are caused by non ideal interactions of paper, ink and printing devices in high speed printing processes. Since print quality is a perceptive characteristic, the measurement of unevenness according to human vision is a significant problem. In this thesis, the mottling phenomenon is studied. Mottling is a printing defect characterized by a spotty, non uniform appearance in solid printed areas. Print mottle is usually the result of uneven ink lay down or non uniform ink absorption across the paper surface, especially visible in mid tone imagery or areas of uniform color, such as solids and continuous tone screen builds. By using existing knowledge on visual perception and known methods to quantify print tone variation, a new method for print unevenness evaluation is introduced. The method is compared to previous results in the field and is supported by psychometric experiments. Pilot studies are made to estimate the effect of optical paper characteristics prior to printing, on the unevenness of the printed area after printing. Instrumental methods for print unevenness evaluation have been compared and the results of the comparison indicate that the proposed method produces better results in terms of visual evaluation correspondence. The method has been successfully implemented as ail industrial application and is proved to be a reliable substitute to visual expertise.

Training system for conceptual design and evaluation for wastewater treatment

Rising population, rapid urbanisation and growing industrialisation have severely stressed water quality and its availability in Malawi. In addition, financial and institutional problems and the expanding agro industry have aggravated this problem. The situation is worsened by depleting water resources and pollution from untreated sewage and industrial effluent. The increasing scarcity of clean water calls for the need for appropriate management of available water resources. There is also demand for a training system for conceptual design and evaluation for wastewater treatment in order to build the capacity for technical service providers and environmental practitioners in the country. It is predicted that Malawi will face a water stress situation by 2025. In the city of Blantyre, this situation is aggravated by the serious pollution threat from the grossly inadequate sewage treatment capacity. This capacity is only 23.5% of the wastewater being generated presently. In addition, limited or non-existent industrial effluent treatment has contributed to the severe water quality degradation. This situation poses a threat to the ecologically fragile and sensitive receiving water courses within the city. This water is used for domestic purposes further downstream. This manuscript outlines the legal and policy framework for wastewater treatment in Malawi. The manuscript also evaluates the existing wastewater treatment systems in Blantyre. This evaluation aims at determining if the effluent levels at the municipal plants conform to existing standards and guidelines and other associated policy and regulatory frameworks. The raw material at all the three municipal plants is sewage. The typical wastewater parameters are Biochemical Oxygen Demand (BOD5), Chemical Oxygen Demand (COD), and Total Suspended Solids (TSS). The treatment target is BOD5, COD, and TSS reduction. Typical wastewater parameters at the wastewater treatment plant at MDW&S textile and garments factory are BOD5 and COD. The treatment target is to reduce BOD5 and COD. The manuscript further evaluates a design approach of the three municipal wastewater treatment plants in the city and the wastewater treatment plant at Mapeto David Whitehead & Sons (MDW&S) textile and garments factory. This evaluation utilises case-based design and case-based reasoning principles in the ED-WAVE tool to determine if there is potential for the tool in Blantyre. The manuscript finally evaluates the technology selection process for appropriate wastewater treatment systems for the city of Blantyre. The criteria for selection of appropriate wastewater treatment systems are discussed. Decision support tools and the decision tree making process for technology selection are also discussed. Based on the treatment targets and design criteria at the eight cases evaluated in this manuscript in reference to similar cases in the ED-WAVE tool, this work confirms the practical use of case-based design and case-based reasoning principles in the ED-WAVE tool in the design and evaluation of wastewater treatment 6 systems in sub-Sahara Africa, using Blantyre, Malawi, as the case study area. After encountering a new situation, already collected decision scenarios (cases) are invoked and modified in order to arrive at a particular design alternative. What is necessary, however, is to appropriately modify the case arrived at through the Case Study Manager in order to come up with a design appropriate to the local situation taking into account technical, socio-economic and environmental aspects. This work provides a training system for conceptual design and evaluation for wastewater treatment.

Kalsiumkarbonaatin kemiallisfysikaalinen käsittely ja materiaalin karakterisointi

Saostettua karbonaattia voidaan käyttää useiden eri teollisuuksien tuotteissa. Pääosin saostettua kalsiumkarbonaattia kuitenkin käytetään paperin, maalien, muovien sekä elintarviketuotteiden täyteaineena. Koska monet käyttökohteet vaativat saostetulta kalsiumkarbonaatilta tiettyjä puhtausvaatimuksia, sen koostumuksen tutkiminen on suuren kiinnostuksen kohteena. Työn perimmäisenä tarkoituksena on ollut määrittää saostetun kalsiumkarbonaatin kemiallinen koostumus ja selvittää, vaikuttavatko materiaalin kemiallisfysikaalinen modifiointi sen ominaisuuksiin. Kirjallisuusosassa käsitellään yleisesti kalsiumkarbonaattimateriaaleja, saostetun kalsiumkarbonaatin valmistusmenetelmiä ja vastaavanlaisen materiaalin esikäsittelymenetelmiä. Lisäksi tarkastellaan erilaisia analyysimenetelmiä, joita voidaan käyttää kiinteiden epäorgaanisten tai mineraalinäytteiden kemiallisen koostumuksen sekä fysikaalisten ja kemiallisten reaktioiden määrittämiseen. Kokeellisessa osassa tutkittiin käsittelemättömiä saostettuja kalsiumkarbonaattinäytteiden ominaisuuksia ja kemiallista koostumusta erilaisilla alkuaine-, ioni-/spesies- sekä pyrolyysimittauksilla. Näytteitä modifioitiin lämmityksen ja jauhatuksen avulla. Modifioinnin vaikutusta näytteiden kemiallisiin koostumuksiin tutkittiin vertailemalla tuloksia käsittelemättömien näytteiden antamiin tuloksiin. Tutkimus osoitti, että näytteiden lämpökäsittelyllä ei ollut lähes ollenkaan vaikutusta näytteiden kemialliseen koostumukseen. Toisin osoitti näytteiden jauhatus, joka laski ammoniumin pitoisuutta näytteissä. Laitetekniikkaa käytettäessä kapillaarielektroforeesi, ionikromatografi, ICP-AES ja SEM (FTIR) antoivat luotettavinta tietoa näytteiden kemiallisista koostumuksista. Näytteiden fysikaalisia ja kemiallisia reaktioita voitiin havainnollistaa parhaiten käyttäen STA-QMS -laitetta.

Microscopic simulation of pigment coating consolidation

The control of coating layer properties is becoming increasingly important as a result of an emerging demand for novel coated paper-based products and an increasing popularity of new coating application methods. The governing mechanisms of microstructure formation dynamics during consolidation and drying are nevertheless, still poorly understood. Some of the difficulties encountered by experimental methods can be overcome by the utilisation of numerical modelling and simulation-based studies of the consolidation process. The objective of this study was to improve the fundamental understanding of pigment coating consolidation and structure formation mechanisms taking place on the microscopic level. Furthermore, it is aimed to relate the impact of process and suspension properties to the microstructure of the coating layer. A mathematical model based on a modified Stokesian dynamics particle simulation technique was developed and applied in several studies of consolidation-related phenomena. The model includes particle-particle and particle-boundary hydrodynamics, colloidal interactions, Born repulsion, and a steric repulsion model. The Brownian motion and a free surface model were incorporated to enable the specific investigation of consolidation and drying. Filter cake stability was simulated in various particle systems, and subjected to a range of base substrate absorption rates and system temperatures. The stability of the filter cake was primarily affected by the absorption rate and size of particles. Temperature was also shown to have an influence. The consolidation of polydisperse systems, with varying wet coating thicknesses, was studied using imposed pilot trial and model-based drying conditions. The results show that drying methods have a clear influence on the microstructure development, on small particle distributions in the coating layer and also on the mobility of particles during consolidation. It is concluded that colloidal properties can significantly impact coating layer shrinkage as well as the internal solids concentration profile. Visualisations of particle system development in time and comparison of systems at different conditions are useful in illustrating coating layer structure formation mechanisms. The results aid in understanding the underlying mechanisms of pigment coating layer consolidation. Guidance is given regarding the relationship between coating process conditions and internal coating slurry properties and their effects on the microstructure of the coating.