Freezing Point Depressions of Dilute Solutions of Alkali Metal Chlorides and Bromides

Freezing point depressions (¿Tf) of dilute solutions of several alkali metal chlorides and bromides were calculated by means of the best activity coefficient equations. In the calculations, Hückel, Hamer and Pitzer equationswere used for activity coefficients. The experimental ¿Tf values available in the literature for dilute LiCl, NaCl and KBr solutions can be predicted within experimental error by the Hückel equations used. The experimental ¿Tf values for dilute LiCl and KBr solutions can also be accurately calculated by corresponding Pitzer equations and those for dilute NaCl solutions by the Hamer equation for this salt. Neither Hamer nor Pitzer equations predict accurately the freezing points reported in the literature for LiBr and NaBr solutions. The ¿Tf values available for dilute solutions of RbCl, CsCl or CsBr are not known at the moment accurately because the existing data for these solutions are not precise. The freezing point depressions are tabulated in the present study for LiCl, NaCl and KBr solutions at several rounded molalities. The ¿Tf values in this table can be highly recommended. The activity coefficient equations used in the calculation of these values have been tested with almost allhigh-precision electrochemical data measured at 298.15 K.

The Influence of Process Conditions on the Deresination Efficiency in Mechanical Pulp Washing

The aim of this thesis was to produce information for the estimation of the flow balance of wood resin in mechanical pulping and to demonstrate the possibilities for improving the efficiency of deresination in practice. It was observed that chemical changes in wood resin take place only during peroxide bleaching, a significant amount of water dispersed wood resin is retained in the pulp mat during dewatering and the amount of wood resin in the solid phase of the process filtrates is very small. On the basis of this information there exist three parameters related to behaviour of wood resin that determine the flow balance in the process: 1. The liberation of wood resin to the pulp water phase 2. Theretention of water dispersed wood resin in dewatering 3. The proportion of wood resin degraded in the peroxide bleaching The effect of different factors on these parameters was evaluated with the help of laboratory studies and a literature survey. Also, information related to the values of these parameters in existing processes was obtained in mill measurements. With the help of this information, it was possible to evaluate the deresination efficiency and the effect of different factors on this efficiency in a pulping plant that produced low-freeness mechanical pulp. This evaluation showed that the wood resin content of mechanical pulp can be significantly decreased if there exists, in the process, a peroxide bleaching and subsequent washing stage. In the case of an optimal process configuration, as high as a 85 percent deresination efficiency seems to be possible with a water usage level of 8 m3/o.d.t.

Electromagnetic Design of a Solid Steel Rotor Motor for Demanding Operation Environments

The solid-rotor induction motor provides a mechanically and thermally reliable solution for demanding environments where other rotor solutions are prohibited or questionable. Solid rotors, which are manufactured of single pieces of ferromagnetic material, are commonly used in motors in which the rotationspeeds exceed substantially the conventional speeds of laminated rotors with squirrel-cage. During the operation of a solid-rotor electrical machine, the rotor core forms a conductor for both the magnetic flux and the electrical current. This causes an increase in the rotor resistance and rotor leakage inductance, which essentially decreases the power factor and the efficiency of the machine. The electromagnetic problems related to the solid-rotor induction motor are mostly associated with the low performance of the rotor. Therefore, the main emphasis in this thesis is put on the solid steel rotor designs. The rotor designs studied in thisthesis are based on the fact that the rotor construction should be extremely robust and reliable to withstand the high mechanical stresses caused by the rotational velocity of the rotor. In addition, the demanding operation environment sets requirements for the applied materials because of the high temperatures and oxidizing acids, which may be present in the cooling fluid. Therefore, the solid rotors analyzed in this thesis are made of a single piece of ferromagnetic material without any additional parts, such as copper end-rings or a squirrel-cage. A pure solid rotor construction is rigid and able to keep its balance over a large speed range. It also may tolerate other environmental stresses such as corroding substances or abrasive particles. In this thesis, the main target is to improve the performance of an induction motor equipped with a solid steel rotor by traditional methods: by axial slitting of the rotor, by selecting a proper rotor core material and by coating the rotor with a high-resistive stainless ferromagnetic material. In the solid steel rotor calculation, the rotor end-effects have a significant effect on the rotor characteristics. Thus, the emphasis is also put on the comparison of different rotor endfactors. In addition, a corrective slip-dependent end-factor is proposed. The rotor designs covered in this thesis are the smooth solid rotor, the axially slitted solid rotor and the slitted rotor having a uniform ferromagnetic coating cylinder. The thesis aims at design rules for multi-megawatt machines. Typically, mega-watt-size solidrotor machines find their applications mainly in the field of electric-motor-gas-compression systems, in steam-turbine applications, and in various types of largepower pump applications, where high operational speeds are required. In this thesis, a 120 kW, 10 000 rpm solid-rotor induction motor is usedas a small-scale model for such megawatt-range solid-rotor machines. The performance of the 120 kW solid-rotor induction motors is determined by experimental measurements and finite element calculations.

On Modelling, System Identification and Control of Servo-Systems with a Flexible Load

The present study was done with two different servo-systems. In the first system, a servo-hydraulic system was identified and then controlled by a fuzzy gainscheduling controller. The second servo-system, an electro-magnetic linear motor in suppressing the mechanical vibration and position tracking of a reference model are studied by using a neural network and an adaptive backstepping controller respectively. Followings are some descriptions of research methods. Electro Hydraulic Servo Systems (EHSS) are commonly used in industry. These kinds of systems are nonlinearin nature and their dynamic equations have several unknown parameters.System identification is a prerequisite to analysis of a dynamic system. One of the most promising novel evolutionary algorithms is the Differential Evolution (DE) for solving global optimization problems. In the study, the DE algorithm is proposed for handling nonlinear constraint functionswith boundary limits of variables to find the best parameters of a servo-hydraulic system with flexible load. The DE guarantees fast speed convergence and accurate solutions regardless the initial conditions of parameters. The control of hydraulic servo-systems has been the focus ofintense research over the past decades. These kinds of systems are nonlinear in nature and generally difficult to control. Since changing system parameters using the same gains will cause overshoot or even loss of system stability. The highly non-linear behaviour of these devices makes them ideal subjects for applying different types of sophisticated controllers. The study is concerned with a second order model reference to positioning control of a flexible load servo-hydraulic system using fuzzy gainscheduling. In the present research, to compensate the lack of dampingin a hydraulic system, an acceleration feedback was used. To compare the results, a pcontroller with feed-forward acceleration and different gains in extension and retraction is used. The design procedure for the controller and experimental results are discussed. The results suggest that using the fuzzy gain-scheduling controller decrease the error of position reference tracking. The second part of research was done on a PermanentMagnet Linear Synchronous Motor (PMLSM). In this study, a recurrent neural network compensator for suppressing mechanical vibration in PMLSM with a flexible load is studied. The linear motor is controlled by a conventional PI velocity controller, and the vibration of the flexible mechanism is suppressed by using a hybrid recurrent neural network. The differential evolution strategy and Kalman filter method are used to avoid the local minimum problem, and estimate the states of system respectively. The proposed control method is firstly designed by using non-linear simulation model built in Matlab Simulink and then implemented in practical test rig. The proposed method works satisfactorily and suppresses the vibration successfully. In the last part of research, a nonlinear load control method is developed and implemented for a PMLSM with a flexible load. The purpose of the controller is to track a flexible load to the desired position reference as fast as possible and without awkward oscillation. The control method is based on an adaptive backstepping algorithm whose stability is ensured by the Lyapunov stability theorem. The states of the system needed in the controller are estimated by using the Kalman filter. The proposed controller is implemented and tested in a linear motor test drive and responses are presented.

Potentiometric titration as a method of determining the stoichiometric dissociation constants of weak acids from the thermodynamic dissociation constants of aqueous solutions at 298.15 K

The simple single-ion activity coefficient equation originating from the Debye-Hückel theory was used to determine the thermodynamic and stoichiometric dissociation constants of weak acids from data concerning galvanic cells. Electromotive force data from galvanic cells without liquid junctions, which was obtained from literature, was studied in conjuction with the potentiometric titration data relating to aqueous solutions at 298.15 K. The dissociation constants of weak acids could be determined by the presented techniques and almost all the experimental data studied could be interpreted within the range of experimental error. Potentiometric titration has been used here and the calculation methods were developed to obtain the thermodynamic and stoichiometric dissociation constants of some weak acids in aqueous solutions at 298.15 K. The ionic strength of titrated solutions were adjusted using an inert electrolyte, namely, sodium or potassium chloride. Salt content alonedetermines the ionic strength. The ionic strength of the solutions studied varied from 0.059 mol kg-1 to 0.37 mol kg-1, and in some cases up to 1.0 mol kg-1. The following substances were investigated using potentiometric titration: aceticacid, propionic acid, L-aspartic acid, L-glutamic acid and bis(2,2-dimethyl-3-oxopropanol) amine.

Effect of Mechanical and Geometric Mismatching on Fatigue and Damage of Welded Joints

The future of high technology welded constructions will be characterised by higher strength materials and improved weld quality with respect to fatigue resistance. The expected implementation of high quality high strength steel welds will require that more attention be given to the issues of crack initiation and mechanical mismatching. Experiments and finite element analyses were performed within the framework of continuum damage mechanics to investigate the effect of mismatching of welded joints on void nucleation and coalescence during monotonic loading. It was found that the damage of undermatched joints mainly occurred in the sandwich layer and the damageresistance of the joints decreases with the decrease of the sandwich layer width. The damage of over-matched joints mainly occurred in the base metal adjacent to the sandwich layer and the damage resistance of the joints increases with thedecrease of the sandwich layer width. The mechanisms of the initiation of the micro voids/cracks were found to be cracking of the inclusions or the embrittled second phase, and the debonding of the inclusions from the matrix. Experimental fatigue crack growth rate testing showed that the fatigue life of under-matched central crack panel specimens is longer than that of over-matched and even-matched specimens. Further investigation by the elastic-plastic finite element analysis indicated that fatigue crack closure, which originated from the inhomogeneousyielding adjacent to the crack tip, played an important role in the fatigue crack propagation. The applicability of the J integral concept to the mismatched specimens with crack extension under cyclic loading was assessed. The concept of fatigue class used by the International Institute of Welding was introduced in the parametric numerical analysis of several welded joints. The effect of weld geometry and load condition on fatigue strength of ferrite-pearlite steel joints was systematically evaluated based on linear elastic fracture mechanics. Joint types included lap joints, angle joints and butt joints. Various combinations of the tensile and bending loads were considered during the evaluation with the emphasis focused on the existence of both root and toe cracks. For a lap joint with asmall lack-of-penetration, a reasonably large weld leg and smaller flank angle were recommended for engineering practice in order to achieve higher fatigue strength. It was found that the fatigue strength of the angle joint depended strongly on the location and orientation of the preexisting crack-like welding defects, even if the joint was welded with full penetration. It is commonly believed that the double sided butt welds can have significantly higher fatigue strength than that of a single sided welds, but fatigue crack initiation and propagation can originate from the weld root if the welding procedure results in a partial penetration. It is clearly shown that the fatigue strength of the butt joint could be improved remarkably by ensuring full penetration. Nevertheless, increasing the fatigue strength of a butt joint by increasing the size of the weld is an uneconomical alternative.

PHOTOCATALYTIC OXIDATION OF AQUEOUS SOLUTIONS OF JET FUEL AND ICING INHIBITORS

The present paper is devoted to the results of experimental research undertaken into photocatalytical oxidation (PCO) of aqueous solutions of de-icing agents and aqueous extract of jet fuel. The report consists of introduction, literature review, description of materials and methods, discussion of results and conclusions. TiO2 was selected as a photocatalyst for the experiments with synthetic solutions of ethylene glycol, 2-ethoxyethanol and aqueous extract of jet fuel. To explain the PCO mechanisms affecting certain behaviour of de-icing agent under distinctive conditions, the following factors were studied: the impact of initial concentration of pollutant, the role of pH, the presence of tert-butanol as OH·-radicals scavenger and mineral admixtures. PCO under solar radiation performed in two ways: catalysed by irradiated TiO2 slurry or by TiO2 attached to buoyant hollow glass micro-spheres. Special attention was paid to the energy-saving PCO with reduced intensity mixing of the slurry. The effect of PCO was assessed by determination of residual chemical oxygen demand of solution (COD) and by measuring of concentration of glycols. The PCO process efficiency was assumed to be dependent on the TiO2 suspension fractional composition. Thus, the following effects of solutions’ media were viewed: presence of organic admixtures, pH influence, mixing mode during the PCO. The effects of mineral admixtures - Ca2+, Fe3+/2+, Mn2+, SO42- - that are often present in natural and wastewater systems or produced during the degradation of organic pollutants and which can affect the rate of PCO of de-icing agents, were also investigated.

Secure IP-based Connection Solutions for Mobile Users

Tämä diplomityö tutkii turvallisia etäyhteystapoja yritysverkkoihin. Samanaikasesti kuin Internettiin liitetyt langattomat verkot, kuten langattomat lähiverkot ja pakettikytkentäiset matkapuhelinverkot, tulevat yhä yleisemmiksi, mahdollisuus etäyhteksien luomiseen näiden verkkojen kautta tulee yhä suositummaksi. Vaikka tietoverkot kehittyvät, pysyvät niitä uhkaavat yleisluontoiset uhat samoina. IP pohjaiset VPN-verkot ovat sopiva tapa suojata Internetin ylitse tapahtuvia etäyhteksiä. Eri VPN-ratkaisuja on kuitenkin tarjolla laaja valikoima. Oikean tyyppisen VPN-ratkaisun valinta on kriittistä, jotta yrityksen etäyhteystarpeet saadaan täytettyä. Diplomityö esittelee eräänä vaihtoehtona miten Pocket PC 2002 PDA laitetta ja Windows XP Professional käyttöjärjestelmää voidaan käyttää edullisen VPN ratkaisun toteuttamiseen.

Developing customer-based e-solutions

Logistiikkapalveluiden markkinat ovat viime vuosina muuttuneet. Kilpailtu toimiala ja asiakasvaatimusten muuttuminen ovat pakottaneet yritykset pyrkimään entistä tehokkaampaan jakeluketjuun. Työn tarkoituksena oli tutkia sähköisten asiakasliittymien toimivuutta asiakkaan näkökulmasta Euro Express tuotannossa ja prosessissa. Tarkoituksena oli selvittää eri sidosryhmien vaatimukset prosessille huomioiden sähköisen liiketoiminnan tuomat edut ja ominaispiirteet. Tavoitteena oli kuvata olemassa oleva prosessi ja tutkia prosessin rajapinnat –asiakas, tuotanto ja ulkoiset sidosryhmät. Tutkielmassa sähköisten ratkaisujen ominaispiirteet on käyty läpi ja tulevaisuuden kehitysnäkökulmista keskusteltu. Kehittyneiden tietoteknisten ratkaisujen avulla jatkuva prosessien uudistaminen (Business Process Reengineering) on mahdollista. Yleisesti epäolennaisuudet asiakasrajapinnassa, informaation kulussa ja yhteyksissä eri järjestelmien välillä aiheuttavat ongelmia sähköisten ratkaisujen toteuttamisessa. Tulevaisuudessa logistiikka yritykset ottavat entistä enemmän käyttöönsä uudenaikaisia teknologisia ratkaisuja tilaukseen, tuotantoon ja asiakaspalveluun. Näiden uudenlaisten ratkaisujen kehittämisestä on hyötyä sekä käyttäjälle että tarjoajalle, mutta ne ovat myös pakollisia palveluntarjoajalle kehittyäkseen markkinoilla. Tulevaisuudessa kilpailun tiivistyessä ja asiakkaiden vaatimusten kasvaessa on kiinnitettävä entistä suurempaa huomiota koko prosessiketjun toimivuuteen. Uudet teknologiset ratkaisut ja niiden käyttäminen tehokkaasti tuovat yrityksille kilpailuetuja, joita ei muuten olisi saavutettavissa.

Market Opportunities Analysis for Logistics Solutions Provider Case Danzas Solutions

Tutkielman tavoitteena oli suunitella markkina-analyysi ja sitä käyttäen määritellä Danzasin Solutions liiketoimintayksikön mahdollisuuksia laajentaa toimintaansa Suomen terveydenhuolto/ lääke- ja elektroniikka/ telekommunikaatiosektoreilla. Danzas Solutions toimisi logistiikkaintegraattorina toimittamalla kokonaisvaltaisia logistisia ratkaisuja. Tutkimus tehtiin haastattelemalla neljää Danzasin asiakasta. Mahdollisimman laajan ja yleistettävän tuloksen saamiseksi haastateltavat valitiin logistiikan ulkoistamisasteeltaan vaihteleviksi. Tutkimus tehtiin ensin tutkimalla sekundääristä informaatiota markkinoilta ja täydentämällä sitä haastatteluista saadulla kvalitatiivisella primääri informaatiolla ja case yrityksen sisäisellä analyysillä. Painopiste tutkimuksessa oli selvittää yritysten ulkoistamiseen ja logistiikkakumppanin valintaan vaikuttavia kriteereitä. Logistiikkaintegraattorille suurimmat mahdollisuudet löytyvät elektroniikka/ telekommunikaatiosektorilta. Logistiikka tällä sektorilla on vaativaa ja yrityksillä ei ole resursseja hallita sitä itse. Terveydenhuolto/ lääkesektorilla yrityksillä on yleensä muut keinot jakeluketjun hallintaan ja ne eivät tarvitse logistiikkaintegraattorin palveluita.

Development of rotating drum under mechanical and thermal load

A variable temperature field sets exacting demands to the structure under mechanical load. Most of all the lifetime of the rotating drum structure depends on temperature differences between parts inside the drum. The temperature difference was known because of the measurements made before. The list of demands was created based on customers’ needs. The limits of this paper were set to the inner structure of the drum. Creation of ideas for the inner structure was started open minded. The main principle in the creation process was to create new ideas for the function of the product with the help of sub-functions. The sub-functions were created as independent as possible. The best sub-functions were combined together and the new working principles were created based on them. Every working principle was calculated separately and criticized at the end of the calculation process. The main objective was to create the new kind of structure, which is not based too much to the old, inoperative structure. The affect of own weight of the inner structure to the stress values was quite small but it was also taken into consideration when calculating the maximum stress value of the structure. Because of very complex structures all of the calculations were made with the help of the ProE – Mechanica software. The fatigue analyze was made also for the best structure solution.

Paperirullan kannatushihnan kestoiän pidentäminen

Työn tavoitteena oli selvittää kannatushihnapituusleikkurissa paperin rullaukseen käytettävän kannatushihnan kestoikään vaikuttavia tekijöitä ja ratkaisuja liian lyhyeen kestoikään liittyviin ongelmiin. Työssä selvitettiin ensin kannatushihnatyyppisen pituusleikkurin toimintaa ja tarkemmin sen rullausosaa ja rullausprosessin parametreja. Kannatushihnan kestoikään vaikuttavia tekijöitä on käsitelty kirjallisuuden ja kohdeyrityksessä olevan materiaalin perusteella. Seuraavaksi esitettiin ideoita kannatushihnan rakenteesta ja materiaaleista sekä vertailtiin niitä keskenään ja nykyiseen hihnan rakenteeseen. Työssä tehtiin nykyistä kannatushihnaa simuloiva kaksiulotteinen elementtimalli. Tämän elementtimallin mukaan pituusleikkurin telojen suunnassa epätasainen hihnan kuluminen johtuu hihnan paksuussuuntaisten jännitysten eroista. Hihnan kulkua arvioitiin kokeellisesti kahdella erityyppisellä hihnalla. Hihnan kulkuun eniten vaikutti esikiristysvoima, jota pienennettäessä kehänopeusero paperirullaa simuloivan kuormittavan telan ja hihnatelan välillä pieneni. Työssä löydettiin mahdollinen yhteys rullauksessa tulostietona saatavan datan sekä hihnan geometrian välille. Polyeteenivaahtomuovit ovat kitkansa puolesta lupaavia hihnan kitkapinnoitteen materiaaliksi. Toisaalta polyeteenivaahtomuovien mekaanisia ominaisuuksia ei juuri tunneta, eikä niitä ole käytetty kulutuskestoa vaativissa sovelluksissa. Hihnan ulkopinnan kulumismekanismia ei täysin tunneta.

Regeneroidun selluloosapinnan modifiointi kestämään mikro-organismien toimintaa

Työn tavoitteena oli kehittää mikro-organismeja kestävä suoli eli makkarankuori. Työ suoritettiin modifioimalla regeneroitua selluloosaa. Modifiointiliuoksena käytettiin etikkahapon ja etikkahappoanhydridin seosta, johon lisättiin rikkihappoa katalyytiksi. Työssä etsittiin parasta yhdistelmää, joka koostui modifiointiradannopeudesta, modifiointiliuoskoostumuksesta ja erilaisista modifiointimenetelmistä. Kirjallisuusosassa käsiteltiin yleisesti asetaattikalvoja, niiden valmistusta ja ominaisuuksia. Lisäksi perehdyttiin entsyymin ominaisuuksiin ja toimintaan yleisesti. Entsyymeistä yksi otettiin lähempään tarkasteluun. Kokeissa regeneroitua selluloosaa modifioitiin liuoksessa, jonka koostumusta muunneltiin. Kokeissa oli kolme erilaista modifiointimenetelmää, joissa käytettiin neljää modifiointiliuoskoostumusta ja kolmea modifiointinopeutta. Mittauksissa tutkittiin modifioinnin vaikutusta suoliin verrattuna normaaleihin suoliin. Suolille tehtiin sekä mekaanisia että kemiallisia testejä. Kemiallisista testeistä tärkein oli testi, jossa modifioitu suoli altistettiin mikro-organismille. Tulosten perusteella valittiin paras menetelmä. Työssä havaittiin yhden menetelmän olevan muita paljon parempi. Tällä menetelmällä suoritettiin toistokokeita, jotka varmistivat jo saatuja tuloksia. Liuoskoostumusten välillä ei ollut suuria eroja, mutta kuitenkin niistä yksi osoittautui parhaimmaksi. Nopeutta oli vaikeampi määrittää, mutta siitäkin saatiin määritettyä tietty haarukka, jossa reaktio oli tehokkain.

Practical Solutions for Increased Safety in Paper Mill Operations

Tämä diplomityö käsittelee työterveys- ja työturvallisuushallinnan (TTT) sekä ympäristönsuojelun ongelmia ja riskejä, joita tehdasalueen toiminnanharjoittaja kohtaa ulkoistaessaan tehdastoimintojaan ja siirtyessään käyttämään 24 h ulkoisia kunnossapitopalveluja. Teoriaosa selventää ulkoistukseen liittyviä lainmukaisia määräyksiä ja vaatimuksia koskien terveyden, turvallisuuden ja ympäristöongelmien hallintaa sellu-, paperi- ja kartonkitehtaissa Euroopassa, Yhdysvalloissa ja Suomessa. TTT-toiminnan tason sekä ympäristönsuojelun tason mittaamisen ongelmat tuodaan esille. Olemassa olevia kansainvälisiä TTT-johtamisjärjestelmien ja ympäristöjärjestelmien standardeja, riskien hallintatyökaluja ja ohjelmia esitellään lyhyesti. Käytännön osa toteutettiin tapaustutkimuksena, jonka kohteena oli Äänekosken tehdaskombinaatti ja kemianteollisuuden laitos, Noviant CMC Oy. TTT-hallintatoimien ja ympäristönsuojelun ongelmia tutkitaan tehdastoimintoja ulkoistettaessa. Integroidun johtamisjärjestelmän auditointimenettelyt, ulkoistuksen kohdealueet, pk-yrityksien riskien hallinta ja ulkoisten työntekijöiden turvallisuuskoulutus ovat erityisen tarkastelun alla. Käyttäen hyväksi kerättyä TTT- ja ympäristöaineistoa, suunniteltiin malli ja sisältöehdotus uudelle internet-selain tyyppiselle työkalulle TTT- ja ympäristöasioiden hallinnan avuksi. Työkalu on tarkoitettu palvelemaan Noviant CMC Oy:n eri sidosryhmien tarpeita. Diplomityön käytännön osa muodostaa pohjan JP MILLSAFE - pilottiprojektille, joka käynnistettiin internet-selain tyyppisen turvallisuuspalvelusovelluksen kehittämiseksi palvelemaan Äänekosken tehdaskombinaatin eri sidosryhmien tarpeita.