Hydrodynamics and Heat Transfer in an Airlift Reactor

Työn teoriaosassa esitetään kirjallisuudessa esiintyviä teoreettisia ja kokeellisia yhtälöitä nesteen nopeuden, kaasun tilavuusosuuden, painehäviön ja lämmönsiirron laskemiseksi. Lisäksi käsitellään airlift-reaktoreiden toimintaa, rakennetta ja teollisia sovelluksia, sekä sekoitusta ja geometrian vaikutusta airlift-reaktoreiden hydrodynaamisiin ominaisuuksiin. Kokeellisessa osassa kuvataan käytetty koelaitteisto ja mittausmenetelmät sekä esitetään saadut koetulokset. Koelaitteisto on viidellä nousuputkella varustettu ulkoisen kierron airlift-reaktori. Kokeellisessa osassa pyritään ratkaisemaan tällaisessa reaktorissa mahdollisesti esiintyviä ongelmia, kuten "slug flown" muodostuminen nousuputkissa sekä fluidien epätasainen jakautuminen nousuputkiin. Lisäksi tutkitaan erilaisten muuttujien, kuten kaasun tilavuusvirran, nesteen viskositeetin, suutinkoon ja nesteen jakoputken rakenteen, vaikutusta kaasun tilavuusosuuteen ja nesteen nopeuteen nousuputkissa. Nesteen nopeudet mitataan merkkiainemenetelmällä ja kaasun tilavuusosuudet manometrimenetelmällä. Lämmönsiirtoa tutkitaan mittaamalla lämpötilaeroja nousuputkissa NiCr-Ni –termoelementeillä. Mittaustulosten perusteella muokataan korrelaatiot kaasun tilavuusosuudelle ja nesteen tyhjäputkinopeudelle. Korrelaatioista lasketut tulokset sopivat kohtuullisen hyvin yhteen mitattujen tulosten kanssa. "Slug flown" ei todettu muodostuvan ongelmaksi 2.5 mPa s pienemmillä viskositeetin arvoilla 2 metriä pitkissä ja 19 mm halkaisijaltaan olevissa putkissa. Lisäksi todettiin, että kaasu- ja nestefaasien jakautumisongelmat voidaan ratkaista rakenteellisesti.

Sähkön ja lämmön yhteistuotannon optimointi

Työn tavoitteena oli suunnitella ja toteuttaa sähkön ja lämmön yhteistuotantolaitoksen tuotannon optimointi. Optimoinnin kriteerinä on tuotannon kannattavuus. Pyrittiin luomaan optimointimalli, joka ottaa optimoinnissa huomioon erityisesti kaukolämmön kulutusennusteen muutokset sekä sähkön pörssihinnan vaihtelut. Tuotannon kannalta olennaisin kriteeri on kaukolämmön kulutusennusteen pohjalta arvioidun kaukolämpökuorman tyydyttäminen mahdollisimman tehokkaasti ja taloudellisesti. Sähkön tuotannon merkittävimmiksi kriteereiksi muodostuivat sähkön tuotannon ennustettavuus ja tuotannon maksimointi sähkön pörssihinnan asettamissa puitteissa. Optimointiohjelmaa ei ole tarkoitus kytkeä suoraan voimalaitoksen ajojärjestelmään, vaan siitä on tarkoitus tulla erillinen ajosuunnittelijan työkalu. Itse ajosuunnitteluun vaikuttaa usein monipuolisemmat suunnittelukriteerit kuin pelkästään tuotannon tuottavuus. Näiden eri kriteerien painotuksia ei ohjelmassa huomioida, vaan ne päättää ajosuunnittelija. Tuloksena saatiin aikaan optimointiohjelma, joka laskee valittujen tuotantovaihtoehtojen kokonaistuotot eri kaukolämmön kulutusennusteiden ja sähkön pörssihintaennusteiden pohjalta.

Sahan lämmöntuotannon ohjaus

Sahalaitoksilla käytetään lämpöenergiaa sahatavaran kuivauksessa. Lämpö tuotetaan pääasiassa polttamalla sivutuotteita, kuten kuorta ja purua. Hyvän kuivauslaadun saavuttamiseksi kuivausilman lämpötilan ja kosteuden on oltava oikean suuruiset. Epäsuotuisat kuivausolosuhteet hidastavat kuivumista tai aiheuttavat kuivausvikoja. Työssä käsiteltävänä sahalla lämpö tuotetaan kahdella sivutuotteita polttavalla kuorikattilalla sekä tarvittaessa raskasöljykattilalla. Raskasöljykattilalla tuotetaan myös kuivaamojen kostutushöyry. Automatiikkaa kehittämällä lämmöntuotanto saatiin reagoimaan paremmin vaihtelevaan lämmöntarpeeseen. Hyvin toimivan lämmöntuo¬tantojärjestelmän ansiosta kuivausolosuhteet ovat säilyneet entistä vakaampina. Matalapaineista höyryä johdetaan osaan sahan kuivaamoista. Höyrytys parantaa kuivauslaatua ja mahdollistaa nopeamman kuivauksen. Kuivaamot höyrytetään kuormanvaihdon jälkeen, jotta ilmankosteus nousee nopeasti tavoitetasolle. Lämmitys-vaiheen jälkeen höyrykostutusta ei tulisi käyttää ennen seuraavaa kuormanvaihtoa. Kehittämällä kuivaamoautomatiikkaa höyryn käyttö saatiin aikaisempaa kustannustehokkaammaksi. Muutoksien avulla polttoainekustannukset ovat pienentyneet.

Radiative Heat Transfer in Boiler Furnaces

Better models are needed for radiative heat transfer in boiler furnaces. If the process is known better, combustion in the furnace can be optimized to produce low emissions. It makes the process to be environmental friendly. Furthermore, if there is a better model of the furnace it can more fully explain what is happening inside the furnace. Using of the model one can quickly and easily analyze how it operates with bio fuels, moist fuels or difficult fuels and improve the operation. Models helps with better estimation of furnace dimensions and result in more accurate understanding of operation. Key component lacking in these models is radiative heat transfer in particle laden gases. If there are no particles than radiative heat transfer can be calculated approximately. There are two problems with current models when used with flow modeling. The first one is a need to account for a particle laden gas and the second one is an absence of a fast algorithm. Fast calculation is needed if radiative heat transfer calculation is done for a large CDF model. Computations slow down if time is required for calculating radiative properties over and over again. This thesis presents a band model for radiative heat transfer in boiler furnaces. Advantage is a quickness of calculation and account of particles in the process.

Stabilization of the ionic form of weak acid cation exchange resins

Weak acid cation exchange (WAC) resins are used in the chromatographic separation of betaine from vinasse, a by-product of sugar industry. The ionic form of the resin determines the elution time of betaine. When a WAC-resin is in hydrogen form, the retention time of betaine is the longest and betaine elutes as the last component of vi-nasse from the chromatographic column. If the feed solution contains salts and its pH is not acidic enough to keep the resin undissociated, the ionic form of the hydrogen form resin starts to alter. Vinasse contains salts and its pH is around 5, it also contains weak acids. To keep the metal ion content (Na/H ratio) of the resin low enough to ensure successful separation of betaine, acid has to be added to either eluent (water) or vinasse. The aim of the present work was to examine by laboratory experiments which option requires less acid. Also the retention mechanism of betaine was investigated by measuring retention volumes of acetic acid and choline in different Na/H ratios of the resin. It was found that the resulting ionic form of the resin is the same regardless of whether the regeneration acid is added to the eluent or the feed solution (vinasse). Be-sides the salt concentration and the pH of vinasse, also the concentration of weak acids in the feed affects the resulting ionic form of the resin. The more buffering capacity vinasse has, the more acid is required to keep the ionic form of the resin desired. Vinasse was found to be quite strong buffer solution, which means relatively high amounts of acid are required to prevent the Na/H ratio from increasing too much. It is known that the retention volume of betaine decreases significantly, when the Na/H ratio increases. This is assumed to occur, because the amount of hydrogen bonds between the carboxylic groups of betaine and the resin decreases. Same behavior was not found with acetic acid. Choline has the same molecular structure as betaine, but instead of carboxylic group it has hydroxide group. The retention volume of choline increased as the Na/H ratio of the resin increased, because of the ion exchange reaction between choline cation and dissociated carboxylic group of the resin. Since the retention behavior of choline on the resin is opposite to the behavior of be-taine, the strong affinity of betaine towards hydrogen form WAC-resin has to be based on its carboxylic group. It is probable that the quaternary ammonium groups also affect the behavior of the carboxylic groups of betaine, causing them to form hydrogen bonds with the carboxylic groups of the resin.

Coolant Flow and Heat Transfer in Pebble-Bed Reactor Core

This thesis gathers knowledge about ongoing high-temperature reactor projects around the world. Methods for calculating coolant flow and heat transfer inside a pebble-bed reactor core are also developed. The thesis begins with the introduction of high-temperature reactors including the current state of the technology. Process heat applications that could use the heat from a high-temperature reactor are also introduced. A suitable reactor design with data available in literature is selected for the calculation part of the thesis. Commercial computational fluid dynamics software Fluent is used for the calculations. The pebble-bed is approximated as a packed-bed, which causes sink terms to the momentum equations of the gas flowing through it. A position dependent value is used for the packing fraction. Two different models are used to calculate heat transfer. First a local thermal equilibrium is assumed between the gas and solid phases and a single energy equation is used. In the second approach, separate energy equations are used for the phases. Information about steady state flow behavior, pressure loss, and temperature distribution in the core is obtained as results of the calculations. The effect of inlet mass flow rate to pressure loss is also investigated. Data found in literature and the results correspond each other quite well, considered the amount of simplifications in the calculations. The models developed in this thesis can be used to solve coolant flow and heat transfer in a pebble-bed reactor, although additional development and model validation is needed for better accuracy and reliability.

Context exchange between devices in mobile environment

Context awareness is emerging on mobile devices. Context awareness can be used to improve usability of a mobile device. Context awareness is particularly important on mobile devices due the limitations they have. At first in this work, a literature review on context awareness and mobile environment is made. For aiding context awareness there exist an implementation of a Context Framework for Symbian S60 devices. It provides a possibility for exchanging the contexts inside the device between the client applications of the local Context Framework. The main contribution of this thesis is to design and implement an enhancement to the S60 Context Framework for providing possibility to exchange context over device boundaries. Using the implemented Context Exchange System, the context exchange is neither depending on the type of the context nor the type of the client. In addition, the clients and the contexts can reside on any interconnected device. The usage of the system is independent of the programming language since in addition to using only Symbian C++ function interfaces it can also be utilized using XML scripts. The Meeting Sniffer application, which uses the Context Exchange System, was also developed in this work. Using this application, it is possible to recognize a meeting situation and suggest device profile change to a user.

Statistical Optimum Design of Heat Exchangers

The optimal design of a heat exchanger system is based on given model parameters together with given standard ranges for machine design variables. The goals set for minimizing the Life Cycle Cost (LCC) function which represents the price of the saved energy, for maximizing the momentary heat recovery output with given constraints satisfied and taking into account the uncertainty in the models were successfully done. Nondominated Sorting Genetic Algorithm II (NSGA-II) for the design optimization of a system is presented and implemented inMatlab environment. Markov ChainMonte Carlo (MCMC) methods are also used to take into account the uncertainty in themodels. Results show that the price of saved energy can be optimized. A wet heat exchanger is found to be more efficient and beneficial than a dry heat exchanger even though its construction is expensive (160 EUR/m2) compared to the construction of a dry heat exchanger (50 EUR/m2). It has been found that the longer lifetime weights higher CAPEX and lower OPEX and vice versa, and the effect of the uncertainty in the models has been identified in a simplified case of minimizing the area of a dry heat exchanger.

Heat Transfer in Plate Heat Exchangers

This study illustrates the different types of plate heat exchangers that are commonly used in various domestic and industrial applications. The main purpose of this paper was to devise a methodology that is capable of calculating optimum number of plates in the design of a plate heat exchanger. To obtain the appropriate number of plates, typically several iterations must be made before a final acceptable design is completed, since plate amount depends on many factors such as, flow velocities, physical properties of the streams, flow channel geometry, allowable pressure drop, plate dimensions, and the gap between the plates. The methodology presented here can be used as a general guide for designing a plate heat exchanger. To investigate the effects of relevant parameters on the thermal-hydraulic design of a plate heat exchanger, several experiments were carried out for single-phase and counter flow arrangement with two brazed plate heat exchangers by varying the flow rates and the inlet temperatures of the fluid streams. The actual heat transfer coefficients obtained based on the experiment were nearly close to the calculated values and to improve the design, a correction factor was introduced. Besides, the effect of flow channel velocity on the pressure drop inside the unit is presented.

Heat transfer in superheaters of the bubbling fluidized bed boiler conversions

It is often reasonable to convert old boiler to bubbling fluidized bed boiler instead of building a new one. Converted boiler consists of old and new heat surfaces which must be fitted to operate together. Prediction of heat transfer in not so ideal conditions sets challenges for designers. Two converted boilers situated in Poland were studied on the grounds of acceptance tests and further studies. Calculation of boiler process was performed with boiler design program. Main interest was heat transfer in superheaters and factors affecting it. Theory for heat transfer is presented according to information found from literature. Results obtained from experimental studies and calculations have been compared. With correct definitions calculated parameters corresponded well to measured data at boiler maximum design load. However overload situations revealed to be difficult to model at least without considering changes in the combustion process which requires readjustments to the design program input values.

A three dimensional study of heat transfer in a supercritical circulating fluidized bed combustor

From the boiler design point of view, it is imperative to know and understand the operation of the boiler. Since comprehensive measurement of a large furnace is impossible, the furnace can be modeled in order to study its behavior and phenomena. This requires the used model to be validated to correspond with the physical furnace behavior. In this thesis, a three dimensional furnace model is validated to match a bituminous coal utilizing, supercritical once-through circulating fluidized bed combustor based on measurement data. The validated model is used for analyzing the furnace heat transfer. Other heat transfer analysis methods are energy balance method based on tube surface temperature measurements and a method based on measured temperature difference between the tube crest and the fin. The latter method was developed in the thesis using Fluent-software. In the theory part, literature is reviewed and the fundamental aspects of circulating fluidized bed are discussed. These aspects are solid particle behavior in fluidization known as hydrodynamics, behavior of fuel and combustion and heat transfer. Fundamental aspects of modeling are also presented.

Statistical Analysis and Numerics of Heat Exchanger Models

The identifiability of the parameters of a heat exchanger model without phase change was studied in this Master’s thesis using synthetically made data. A fast, two-step Markov chain Monte Carlo method (MCMC) was tested with a couple of case studies and a heat exchanger model. The two-step MCMC-method worked well and decreased the computation time compared to the traditional MCMC-method. The effect of measurement accuracy of certain control variables to the identifiability of parameters was also studied. The accuracy used did not seem to have a remarkable effect to the identifiability of parameters. The use of the posterior distribution of parameters in different heat exchanger geometries was studied. It would be computationally most efficient to use the same posterior distribution among different geometries in the optimisation of heat exchanger networks. According to the results, this was possible in the case when the frontal surface areas were the same among different geometries. In the other cases the same posterior distribution can be used for optimisation too, but that will give a wider predictive distribution as a result. For condensing surface heat exchangers the numerical stability of the simulation model was studied. As a result, a stable algorithm was developed.