Catalysis by gold for biomass transformations

The development of new technologies to supplement fossil resources has led to a growing interest in the utilization of alternative routes. Biomass is a rich renewable feedstock for producing fine chemicals, polymers, and a variety of commodities replacing petroleumderived chemicals. Transformation of biomass into diverse valuable chemicals is the key concept of a biorefinery. Catalytic conversion of biomass, which reduces the use of toxic chemicals is one of the important approaches to improve the profitability of biorefineries. Utilization of gold catalysts allows conducting reactions under environmentally-friendly conditions, with a high catalytic activity and selectivity. Gold-catalyzed valorization of several biomass-derived compounds as an alternative approach to the existing technologies was studied in this work. Isomerization of linoleic acid via double bond migration towards biologically active conjugated linoleic acid isomers (CLA) was investigated. The activity and selectivity of various gold catalysts towards cis-9,trans-11-CLA and trans-10,cis-12-CLA were investigated in a semi-batch reactor, showing that the yield of the desired products varied, depending on the catalyst support. The structure sensitivity in the selective oxidation of arabinose was demonstrated using a series of gold catalysts with different Au cluster sizes in a shaker reactor operating in a semibatch mode. The gas-phase selective oxidation of ethanol was studied and the influence of the catalyst support on the catalytic performance was investigated. The selective oxidation of the lignan hydroxymatairesinol (HMR), extracted from the Norway spruce (Picea abies) knots, to the lignan oxomatairesinol (oxoMAT) was extensively investigated. The influence of the reaction conditions and catalyst properties on the yield of oxoMAT was evaluated. In particular, the structure sensitivity of the reaction was demonstrated. The catalyst deactivation and regeneration procedures were studied. The reaction kinetics and mechanism were advanced.

A platform for anti-biofilm assays combining viability, biomass and matrix quantifications in susceptibility assessments of antimicrobials against Staphylococcus aureus biofilms

Bacteria can exist as planktonic, the lifestyle in which single cells exist in suspension, and as biofilms, which are surface-attached bacterial communities embedded in a selfproduced matrix. Most of the antibiotics and the methods for antimicrobial work have been developed for planktonic bacteria. However, the majority of the bacteria in natural habitats live as biofilms. Biofilms develop dauntingly fast high resistance towards conventional antibacterial treatments and thus, there is a great need to meet the demands of effective anti-biofilm therapy. In this thesis project it was attempted to fill the void of anti-biofilm screening methods by developing a platform of assays that evaluate the effect that screened compounds have on the total biomass, viability and the extracellular polysaccharide (EPS) layer of the biofilms. Additionally, a new method for studying biofilms and their interactions with compounds in a continuous flow system was developed using capillary electrochromatography (CEC). The screening platform was utilized with a screening campaign using a small library of cinchona alkaloids. The assays were optimized to be statistically robust enough for screening. The first assay, based on crystal violet staining, measures total biofilm biomass, and it was automated using a liquid handling workstation to decrease the manual workload and signal variation. The second assay, based on resazurin staining, measures viability of the biofilm, and it was thoroughly optimized for the strain used, but was then a very simple and fast method to be used for primary screening. The fluorescent resazurin probe is not toxic to the biofilms. In fact, it was also shown in this project that staining the biofilms with resazurin prior to staining with crystal violet had no effect on the latter and they can be used in sequence on the same screening plate. This sequential addition step was indeed a major improvement on the use of reagents and consumables and also shortened the work time. As a third assay in the platform a wheat germ agglutinin based assay was added to evaluate the effect a compound has on the EPS layer. Using this assay it was found that even if compounds might have clear effect on both biomass and viability, the EPS layer can be left untouched or even be increased. This is a clear implication of the importance of using several assays to be able to find “true hits” in a screening setting. In the pilot study of screening for antimicrobial and anti-biofilm effects using a cinchona alkaloid library, one compound was found to have antimicrobial effect against planktonic bacteria and prevent biofilm formation at low micromolar concentration. To eradicate biofilms, a higher concentration was needed. It was also shown that the chemical space occupied by the active compound was slightly different than the rest of the cinchona alkaloids as well as the rest of the compounds used for validatory screening during the optimization processes of the separate assays.

The effects of location, feedstock availability, and supply-chain logistics on the greenhouse gas emissions of forest-biomass energy utilization in Finland

Forest biomass represents a geographically distributed feedstock, and geographical location affects the greenhouse gas (GHG) performance of a given forest-bioenergy system in several ways. For example, biomass availability, forest operations, transportation possibilities and the distances involved, biomass end-use possibilities, fossil reference systems, and forest carbon balances all depend to some extent on location. The overall objective of this thesis was to assess the GHG emissions derived from supply and energy-utilization chains of forest biomass in Finland, with a specific focus on the effect of location in relation to forest biomass’s availability and the transportation possibilities. Biomass availability and transportation-network assessments were conducted through utilization of geographical information system methods, and the GHG emissions were assessed by means of lifecycle assessment. The thesis is based on four papers in which forest biomass supply on industrial scale was assessed. The feedstocks assessed in this thesis include harvesting residues, smalldiameter energy wood and stumps. The principal implication of the findings in this thesis is that in Finland, the location and availability of biomass in the proximity of a given energyutilization or energy-conversion plant is not a decisive factor in supply-chain GHG emissions or the possible GHG savings to be achieved with forest-biomass energy use. Therefore, for the greatest GHG reductions with limited forest-biomass resources, energy utilization of forest biomass in Finland should be directed to the locations where most GHG savings are achieved through replacement of fossil fuels. Furthermore, one should prioritize the types of forest biomass with the lowest direct supply-chain GHG emissions (e.g., from transport and comminution) and the lowest indirect ones (in particular, soil carbon-stock losses), regardless of location. In this respect, the best combination is to use harvesting residues in combined heat and power production, replacing peat or coal.

The role of potassium in the corrosion of superheater materials in boilers firing biomass

Inhibition of global warming has become one of the major goals for the coming decades. A key strategy is to replace fossil fuels with more sustainable fuels, which has generated growing interest in the use of waste-derived fuels and of biomass fuels. However, from the chemical point of view, biomass is an inhomogeneous fuel, usually with a high concentration of water and considerable amounts of potassium and chlorine, all of which are known to affect the durability of superheater tubes. To slow down or reduce corrosion, power plants using biomass as fuel have been forced to operate at lower steam temperatures as compared to fossil fuel power plants. This reduces power production efficiency: every 10°C rise in the steam temperature results in an approximate increase of 2% in power production efficiency. More efficient ways to prevent corrosion are needed so that power plants using biomass and waste-derived fuels can operate at higher steam temperatures. The aim of this work was to shed more light on the alkali-induced corrosion of superheater steels at elevated temperatures, focusing on potassium chloride, the alkali salt most frequently encountered in biomass combustion, and on potassium carbonate, another potassium salt occasionally found in fly ash. The mechanisms of the reactions between various corrosive compounds and steels were investigated. Based on the results, the potassium-induced accelerated oxidation of chromia protected steels appears to occur in two consecutive stages. In the first, the protective chromium oxide layer is destroyed through a reaction with potassium leading to the formation of intermediates such as potassium chromate (K2CrO4) and depleting the chromium in the protective oxide layer. As the chromium is depleted, chromium from the bulk steel diffuses into the oxide layer to replenish it. In this stage, the ability of the material to withstand corrosion depends on the chromium content (which affects how long it takes the chromium in the oxide layer to be depleted) and on external factors such as temperature (which affects how fast the chromium diffuses into the protective oxide from the bulk steel). For accelerated oxidation to continue, the presence of chloride appears to be essential.

Comparison of Biomass Gasification Technologies for Natural Gas Substitution in Iron Ore Pelletizing Plants

The iron ore pelletizing process consumes high amounts of energy, including nonrenewable sources, such as natural gas. Due to fossil fuels scarcity and increasing concerns regarding sustainability and global warming, at least partial substitution by renewable energy seems inevitable. Gasification projects are being successfully developed in Northern Europe, and large-scale circulating fluidized bed biomass gasifiers have been commissioned in e.g. Finland. As Brazil has abundant biomass resources, biomass gasification is a promising technology in the near future. Biomasses can be converted into product gas through gasification. This work compares different technologies, e.g. air, oxygen and steam gasification, focusing on the use of the product gas in the indurating machine. The use of biosynthetic natural gas is also evaluated. Main parameters utilized to assess the suitability of product gas were adiabatic flame temperature and volumetric flow rate. It was found that low energy content product gas could be utilized in the traveling grate, but it would require burner’s to be changed. On the other hand, bio-SGN could be utilized without any adaptions. Economical assessment showed that all gasification plants are feasible for sizes greater than 60 MW. Bio-SNG production is still more expensive than natural gas in any case.

Chromatographic recovery of chemicals from acidic biomass hydrolysates

Lignocellulosic biomasses (e.g., wood and straws) are a potential renewable source for the production of a wide variety of chemicals that could be used to replace those currently produced by petrochemical industry. This would lead to lower greenhouse gas emissions and waste amounts, and to economical savings. There are many possible pathways available for the manufacturing of chemicals from lignocellulosic biomasses. One option is to hydrolyze the cellulose and hemicelluloses of these biomasses into monosaccharides using concentrated sulfuric acid as catalyst. This process is an efficient method for producing monosaccharides which are valuable platforn chemicals. Also other valuable products are formed in the hydrolysis. Unfortunately, the concentrated acid hydrolysis has been deemed unfeasible mainly due to high chemical consumption resulting from the need to remove sulfuric acid from the obtained hydrolysates prior to the downstream processing of the monosaccharides. Traditionally, this has been done by neutralization with lime. This, however, results in high chemical consumption. In addition, the by-products formed in the hydrolysis are not removed and may, thus, hinder the monosaccharide processing. In order to improve the feasibility of the concentrated acid hydrolysis, the chemical consumption should be decreased by recycling of sulfuric acid without neutralization. Furthermore, the monosaccharides and the other products formed in the hydrolysis should be recovered selectively for efficient downstream processing. The selective recovery of the hydrolysis by-products would have additional economical benefits on the process due to their high value. In this work, the use of chromatographic fractionation for the recycling of sulfuric acid and the selective recovery of the main components from the hydrolysates formed in the concentrated acid hydrolysis was investigated. Chromatographic fractionation based on the electrolyte exclusion with gel type strong acid cation exchange resins in acid (H+) form as a stationary phase was studied. A systematic experimental and model-based study regarding the separation task at hand was conducted. The phenomena affecting the separation were determined and their effects elucidated. Mathematical models that take accurately into account these phenomena were derived and used in the simulation of the fractionation process. The main components of the concentrated acid hydrolysates (sulfuric acid, monosaccharides, and acetic acid) were included into this model. Performance of the fractionation process was investigated experimentally and by simulations. Use of different process options was also studied. Sulfuric acid was found to have a significant co-operative effect on the sorption of the other components. This brings about interesting and beneficial effects in the column operations. It is especially beneficial for the separation of sulfuric acid and the monosaccharides. Two different approaches for the modelling of the sorption equilibria were investigated in this work: a simple empirical approach and a thermodynamically consistent approach (the Adsorbed Solution theory). Accurate modelling of the phenomena observed in this work was found to be possible using the simple empirical models. The use of the Adsorbed Solution theory is complicated by the nature of the theory and the complexity of the studied system. In addition to the sorption models, a dynamic column model that takes into account the volume changes of the gel type resins as changing resin bed porosity was also derived. Using the chromatography, all the main components of the hydrolysates can be recovered selectively, and the sulfuric acid consumption of the hydrolysis process can be lowered considerably. Investigation of the performance of the chromatographic fractionation showed that the highest separation efficiency in this separation task is obtained with a gel type resin with a high crosslinking degree (8 wt. %); especially when the hydrolysates contain high amounts of acetic acid. In addition, the concentrated acid hydrolysis should be done with as low sulfuric acid concentration as possible to obtain good separation performance. The column loading and flow rate also have large effects on the performance. In this work, it was demonstrated that when recycling of the fractions obtained in the chromatographic fractionation are recycled to preceding unit operations these unit operations should included in the performance evaluation of the fractionation. When this was done, the separation performance and the feasibility of the concentrated acid hydrolysis process were found to improve considerably. Use of multi-column chromatographic fractionation processes, the Japan Organo process and the Multi-Column Recycling Chromatography process, was also investigated. In the studied case, neither of these processes could compete with the single-column batch process in the productivity. However, due to internal recycling steps, the Multi-Column Recycling Chromatography was found to be superior to the batch process when the product yield and the eluent consumption were taken into account.

Recovery of biomass-derived valuable compounds using chromatographic and membrane separations

Utilization of biomass-based raw materials for the production of chemicals and materials is gaining an increasing interest. Due to the complex nature of biomass, a major challenge in its refining is the development of efficient fractionation and purification processes. Preparative chromatography and membrane filtration are selective, energy-efficient separation techniques which offer a great potential for biorefinery applications. Both of these techniques have been widely studied. On the other hand, only few process concepts that combine the two methods have been presented in the literature. The aim of this thesis was to find the possible synergetic effects provided by combining chromatographic and membrane separations, with a particular interest in biorefinery separation processes. Such knowledge could be used in the development of new, more efficient separation processes for isolating valuable compounds from complex feed solutions that are typical for the biorefinery environment. Separation techniques can be combined in various ways, from simple sequential coupling arrangements to fully-integrated hybrid processes. In this work, different types of combined separation processes as well as conventional chromatographic separation processes were studied for separating small molecules such as sugars and acids from biomass hydrolysates and spent pulping liquors. The combination of chromatographic and membrane separation was found capable of recovering high-purity products from complex solutions. For example, hydroxy acids of black liquor were successfully recovered using a novel multistep process based on ultrafiltration and size-exclusion chromatography. Unlike any other separation process earlier suggested for this challenging separation task, the new process concept does not require acidification pretreatment, and thus it could be more readily integrated into a pulp-mill biorefinery. In addition to the combined separation processes, steady-state recycling chromatography, which has earlier been studied for small-scale separations of high-value compounds only, was found a promising process alternative for biorefinery applications. In comparison to conventional batch chromatography, recycling chromatography provided higher product purity, increased the production rate and reduced the chemical consumption in the separation of monosaccharides from biomass hydrolysates. In addition, a significant further improvement in the process performance was obtained when a membrane filtration unit was integrated with recycling chromatography. In the light of the results of this work, separation processes based on combining membrane and chromatographic separations could be effectively applied for different biorefinery applications. The main challenge remains in the development of inexpensive separation materials which are resistant towards harsh process conditions and fouling.

Wet oxidation of biomass for chemical production

Tämän kandidaatintyön tarkoituksena oli tutkia märkähapetusprosessia jätevesien käsittely-menetelmänä ja mahdollisena menetelmänä kemikaalien tuottamiseksi jätevesistä. Erityishuomio on kiinnitetty paperiteollisuudessa syntyviin jätevesiin. Teoriaosassa käsitellään vesikiertoja paperitehtaassa, paperitehtaalla syntyvän jäteveden ominaisuuksia sekä itse märkähapetusprosessia. Märkähapetusprosessissa perehdytään tavalliseen happea käyttävään märkähapetukseen sekä vetyperoksidia käyttävään menetelmään sekä näissä prosesseissa syntyviin väli- ja lopputuotteisiin. Märkähapetus (WO) on terminen hapetusmenetelmä, jolla voidaan käsitellä jätevesiä, jotka ovat liian konsentroituja biologisiin käsittelyihin tai jotka ovat huonosti biohajoavia. Märkähapetuksen tarkoituksena on parantaa molekulaarisen hapen ja orgaanisen aineen välistä kontaktia, jolloin orgaaninen aines pilkkoutuu muodostaen pääasiassa karboksyylihappoja, aldehydejä, hiilidioksidia ja vettä. Märkähapetuksessa hapettavana kaasuna voidaan käyttää joko puhdasta happea tai ilmaa. Vetyperoksidia käyttävässä märkähapetuksessa (WPO) hapettava kaasu on korvattu nestemäisellä vetyperoksidilla. Kokeellisessa osassa tutkittiin orgaanisen aineksen hapetusta käyttäen Fentonin reagenssia, jolloin katalyyttina reaktiossa toimii rautaionit (Fe2+ ja Fe3+) ja hapettimena vetyperoksidi. Hapetettavana jätevetenä käytettiin paperitehtaan hiomolta saatua kiertovettä, TMP-vettä. Hapetuskokeita tehtiin eri vetyperoksidin annoksilla ja katalyytin määrillä eri lämpötiloissa. Hapetuksen jälkeen näytteistä mitattiin kemiallinen hapenkulutus (COD), orgaanisen hiilen kokonaismäärä (TOC) sekä pH. Lisäksi näytteistä määritettiin nestekromatografilla (HPLC) tyypillisten välituotteiden, kuten oksaalihapon, muurahaishapon ja etikkahapon, määrät. Tehdyissä kokeissa COD-arvoja saatiin pienennettyä 50-88 % siten, että suodatetuissa näytteissä muutos oli suurempi kuin suodattamattomissa näytteissä. Lisäksi TOC-arvot laskivat 28-58 %. Tehdyissä kokeissa saatiin myös tuotettua välituotteina karboksyylihappoja, joista etikkahappoa ja oksaalihappoa tuotettiin suurimmat määrät. Myös muurahaishappoa ja meripihkahappoa saatiin tuotettua.

Greenhouse gas emissions from peat and biomass-derived fuels, electricity and heat — Estimation of various production chains by using LCA methodology

More discussion is required on how and which types of biomass should be used to achieve a significant reduction in the carbon load released into the atmosphere in the short term. The energy sector is one of the largest greenhouse gas (GHG) emitters and thus its role in climate change mitigation is important. Replacing fossil fuels with biomass has been a simple way to reduce carbon emissions because the carbon bonded to biomass is considered as carbon neutral. With this in mind, this thesis has the following objectives: (1) to study the significance of the different GHG emission sources related to energy production from peat and biomass, (2) to explore opportunities to develop more climate friendly biomass energy options and (3) to discuss the importance of biogenic emissions of biomass systems. The discussion on biogenic carbon and other GHG emissions comprises four case studies of which two consider peat utilization, one forest biomass and one cultivated biomasses. Various different biomass types (peat, pine logs and forest residues, palm oil, rapeseed oil and jatropha oil) are used as examples to demonstrate the importance of biogenic carbon to life cycle GHG emissions. The biogenic carbon emissions of biomass are defined as the difference in the carbon stock between the utilization and the non-utilization scenarios of biomass. Forestry-drained peatlands were studied by using the high emission values of the peatland types in question to discuss the emission reduction potential of the peatlands. The results are presented in terms of global warming potential (GWP) values. Based on the results, the climate impact of the peat production can be reduced by selecting high-emission-level peatlands for peat production. The comparison of the two different types of forest biomass in integrated ethanol production in pulp mill shows that the type of forest biomass impacts the biogenic carbon emissions of biofuel production. The assessment of cultivated biomasses demonstrates that several selections made in the production chain significantly affect the GHG emissions of biofuels. The emissions caused by biofuel can exceed the emissions from fossil-based fuels in the short term if biomass is in part consumed in the process itself and does not end up in the final product. Including biogenic carbon and other land use carbon emissions into the carbon footprint calculations of biofuel reveals the importance of the time frame and of the efficiency of biomass carbon content utilization. As regards the climate impact of biomass energy use, the net impact on carbon stocks (in organic matter of soils and biomass), compared to the impact of the replaced energy source, is the key issue. Promoting renewable biomass regardless of biogenic GHG emissions can increase GHG emissions in the short term and also possibly in the long term.

Fate of fuel-bound nitrogen and sulfur in biomass-fired Industrial boilers

Användning av biomassa som energikälla för produktion av el och värme är ett sätt att minska beroendet av fossila bränslen och höja självförsörjningen av energi. Fossila bränslen är den främsta källan till koldioxid utsläpp förorsakad av människan. Biomassa, å andra sidan, betraktas som en koldioxidneutral energikälla. Svavlet och kvävet i biomassan bildar dock föroreningar såsom kväveoxider (NOX) och svaveldioxid (SO2), som bidrar till försurning av mark och sjöar. Svavlet i bränslet kan även både förorsaka och förhindra korrosion i en förbränningsanläggning, beroende på förbränningen och bränslet. Huvudsyftet med detta arbete var att få en bättre förståelse om hur utsläppen av NOX och SO2 bildas från bränslebundet kväve och svavel vid förbränning av olika biobränslen. Mätkampanjer i fullskaliga förbränningsanläggningar utfördes, där gassammansättningen mättes i eldstaden och rökgasen. Förståelsen om gaskemin i eldstaden är viktig, för att möjliggöra utvecklandet av renare och effektivare förbränningsanläggningar. Ett annat syfte med arbetet var att klargöra om sulfatering av askkomponenter vid förbränning av biobränslen med olika askegenskaper. Alkaliklorider som bildas vid biomassaförbränning kan orsaka korrosion av värmeöverföringsytor. Svavlet i bränslet visade sig ha en viktig roll i att sulfatera alkaliklorider till mindre korrosiva alkalisulfater. Närvaron av gasformig svavelsyra i rökgaskanalen av förbränningsanläggningar studerades även. Kondensering av svavelsyra leder till korrosion av rökgaskanalen och dess delar. Om svavelsyrakoncentrationen i rökgasen är känd, kan daggpunktstemperaturen beräknas och kondensering av svavelsyra förhindras. I arbetet utvecklades en mätmetod för att mäta låga koncentrationer av gasformig svavelsyra i rökgaser. Denna metod användes för att undersöka risken av lågtemperaturkorrosion orsakad av svavelsyra i förbränningsanläggningar. ------------------------------------------------------------------------------------------------------------ Käyttämällä biomassaa energianlähteenä voidaan vähentää sähkön- ja lämmöntuotannon riippuvuutta fossiilisiin polttoaineisiin. Biomassan käytöllä voidaan myös lisätä energiantuotannon omavaraisuutta. Fossiiliset polttoaineet ovat pääasiallinen syy ihmisen aiheuttamiin hiilidioksidipäästöihin. Biomassa sen sijaan luetaan hiilidioksidineutraaleihin energianlähteisiin. Biopolttoaineiden käytössä tosin vapautuu typpi- ja rikkioksideja, jotka edesauttavat maaperän ja merien happamoitumista. Lisäksi biopolttoaineen rikki voi sekä vähentää että aiheuttaa laitteiden korroosiota energiantuotannossa riippuen biopolttoaineesta ja palamisesta. Tämän työn päätavoitteena oli selvittää mitä biopolttoaineeseen sitoutuneelle typelle ja rikille tapahtuu teollisissa polttolaitoksissa. Kyseisten oksidien muodostumista tutkittiin polttamalla eri biomassoja polttolaitoksissa. Tutkimukset toteutettiin mittauskampanjoilla useissa polttolaitoksissa. Kaasujen koostumusta mitattiin sekä tulipesässä, että savukaasuista. Kaasujen koostumus varsinkin tulipesässä on tärkeää, jotta tulevaisuudessa voidaan rakentaa puhtaampia ja tehokkaampia polttolaitoksia. Työn toisena tavoitteena oli selvittää biomassan polton yhteydessä tapahtuvaa tuhkan sulfatoitumista. Alkalikloridit, joita muodostuu biomassan poltossa, voivat aiheuttaa lämmönsiirtopintojen korroosiota. Rikki osoittautui tärkeäksi osaksi prosessia, jossa korroosiota aiheuttavat alkalikloridit sulfatoituivat vähemmän korrosoiviksi alkalisulfaateiksi. Myös kaasumaisen rikkihapon läsnäoloa savukaasuissa tutkittiin. On todettu, että kaasumuotoinen rikkihappo johtaa korroosioon savukaasukanavan kylmässä päässä ja sen eri osissa rikkihapon tiivistyessä lämpötilan laskiessa. Mikäli rikkihapon pitoisuus savukaasussa tiedetään, sen kastepiste voidaan laskea ja tiivistyminen estää. Tässä työssä kehitettiin mittausmenetelmä rikkihapon alhaisten pitoisuuksien mittaamiseen. Menetelmää hyödynnettiin polttolaitoksissa, joissa tutkittiin rikkihapon tiivistymisestä johtuvaa korroosiota.

Towards optimal fractionation of lignocellulosic biomass using switchable ionic liquids

En ny familj av reversibla (switchable) joniska vätskor (SIL) innehållande 1,8-diazobicyklo-[5.4.0]-undek-7-en (DBU), en molekyl innehållande en eller flera hydroxyl- grupper (t.ex. glycerol) och en sur gas (CO2, SO2) syntetiserades via en enkel procedur samt karakteriserades. [DBU][karbonat] eller [sulfonat] bildades ur en respektive icke-jonisk blandning av en molekylär, organisk polyol (eller ennan molekyl innehållande en OH-grupp) och en amidinbas under bubblandet av en sur gas. Därtill kunde den joniska vätskan omvandlas tillbaka till sina beståndsdelar med hjälp av att upphetta och/eller bubbla en inert gas såsom kväve genom vätskan. SIL- strukturerna kartlades med bl.a. NMR- och FTIR- spektroskopi. Omvandlingen från lågpolära (molekylära) vätskor till högpolära joniska vätskor (SIL) bekräftades även genom att observera förändringar i deras fysikaliska egenskaper, såsom viskositet och färg. Nedbrytningstemperaturerna hos SILs bestämdes med hjälp av termogravimetrisk analys (TGA) som antydde att nedbrytningstemperaturen hos de syntetiserade föreningarna log mellan 50 och 200oC. De nya joniska vätskorna uppvisade högre nedbrytningstemperaturer jämfört med i litteraturen tidigare förekommande exempel och kunde därför tillämpas på flera ändamål. Därtill, reversibla (switchable) joniska vätskor uppbyggda av bl.a. alkoholer, antingen hexanol eller butanol, och CO2 samt en amidin (DBU) användes vid upplösning och fraktionering av ved. Joniska vätskor syntetiserade ur glycerol och sura gaser tillsammans med amidiner användes även för fraktionering av andra lignocellulosor såsom färsk björk (Betula pendula). Björkflis utsattes för behandling, för en period på en till fem dagar vid 100oC och under atmosfäriskt tryck. Alla syntetiserade joniska vätskor visade sig vara relativt neutrala i avseende på upplösning och avlägsnandet av lignin. Slutligen, optimala fraktioneringprocessbetingelser för ved med reversibla joniska vätskor kartlades. Fraktionering av vedbiomassa med dessa joniska vätskor uppvisade sig att vara en selektiv och effektiv metod för extraktion av olika komponenter från lignocellulosa. Den olösta fraktionen hos en vedflis, närmast cellulosa, fibrillerades. -------------------------------------------------------------------------------------------------------------------- Tässä työssä kehitettiin perhe uuden tyyppisiä, reversiibeleitä (switchable) ioninesteitä ( SIL ) joka koostuvat orgaanisesta super-emäksestä kuten 1,8- diatsabisyklo [ 5.4.0] undek- 7-eeni (DBU ) ja yhden tai useampia hydroksyyliryhmiä sisältältävästä molekyylistä (esim. glyseroli) ja happamasta kaasusta (CO2 , SO2) yksinkertaisen menetelmän avulla. [DBU] [ karbonaatti] tai [sulfonaatti] syntetisoitiin kunkin lähtöaineen seoksista kuplittamalla seosta happamalla kaasulla jolloin eksoterminen reaktio tapahtui ja ioninen neste syntyi. Ioniset nesteet voitiin palauttaa takaisin lähtöaineseokseksi kuumentamalla ja/tai kuplittamalla neutraalia kaasua (esim. typpi) seoksen läpi. SIL rakenteet määritettiin ja niiden ominaisuudet kartoitettiin eri menetelmillä, mukaan lukien NMR- ja FTIR -spektroskopia. Ionisen, korkeapoläärisen nesteen syntyminen todennettiin myös viskositeettimittauksilla ja värinmuutoksilla käyttäen hyväksi polariteetti-indikaattoria (Nile red). Myös hajoamislämpötilat määritettiin termogravimetrisellä analyysillä (TGA) ja todettiin että syntetisoitujen yhdisteiden hajoamislämpötila oli välillä 50 ja 200oC . Näiden uusien reversiibeleiden ioninesteiden hajoamisämpötilat olivat korkeammat verrattuna kirjallisuudessa aikaisemmin mainittuihin esimerkkeihin joten niitä voidaan soveltaa useisiin tarkoituksiin. Myös ioninesteitä jotka sisälsivät primäärejä alkoholeja rakennusaineina syntetisoitiin ja hyödynnettiin puun fraktioinnissa. Männyn ja kuusen lisäksi tuoreita koivulastuja onnistuttiin fraktioimaan miedoissa olosuhteissa. Kaikkien syntetisoitujen ioninesteiden todettiin olevan suhteellisen neutraaleja ligniinin liuotuksen suhteen. Vielä, optimaaliset fraktiointiolosuhteet määritettiin ryhmälle reversiibeleitä ioninesteitä ja näiden uudenlaisten ioninesteiden todettiin olevan tehokkaita puun ja muiden lignoselluloosien eri fraktioiden liuotuksessa. Liukenematon osa puulastua joka oli lähinnä selluloosaa fibrilloitui.

Pressure filtration characteristics of enzymatically hydrolyzed biomass suspensions

Enzymatic hydrolysis of lignocellulosic polymers is likely to become one of the key technologies enabling industrial production of liquid biofuels and chemicals from lignocellulosic biomass. Certain types of enzymes are able to hydrolyze cellulose and hemicellulose polymers to shorter units and finally to sugar monomers. These monomeric sugars are environmentally acceptable carbon sources for the production of liquid biofuels, such as bioethanol, and other chemicals, such as organic acids. Liquid biofuels in particular have been shown to contribute to the reduction of net emissions of greenhouse gases. The solid residue of enzymatic hydrolysis is composed mainly of lignin and partially degraded fibers, while the liquid phase contains the produced sugars. It is usually necessary to separate these two phases at some point after the hydrolysis stage. Pressure filtration is an efficient technique for this separation. Solid-liquid separation of biomass suspensions is difficult, because biomass solids are able to retain high amounts of water, which cannot be readily liberated by mechanical separation techniques. Most importantly, the filter cakes formed from biomaterials are compressible, which ultimately means that the separation may not be much improved by increasing the filtration pressure. The use of filter aids can therefore facilitate the filtration significantly. On the other hand, the upstream process conditions have a major influence on the filtration process. This thesis investigates how enzymatic hydrolysis and related process conditions affect the filtration properties of a cardboard suspension. The experimental work consists of pressure filtration and characterization of hydrolysates. The study provides novel information about both issues, as the relationship between enzymatic hydrolysis conditions and subsequent filtration properties has so far not been considered in academic studies. The results of the work reveal that the final degree of hydrolysis is an important factor in the filtration stage. High hydrolysis yield generally increases the average specific cake resistance. Mixing during the hydrolysis stage resulted in undefined changes in the physical properties of the solid residue, causing a high filtration resistance when the mixing intensity was high. Theoretical processing of the mixing data led to an interesting observation: the average specific cake resistance was observed to be linearly proportional to the mixer shear stress. Another finding worth attention is that the size distributions of the solids did not change very dramatically during enzymatic hydrolysis. There was an observable size reduction during the first couple of hours, but after that the size reduction was minimal. Similarly, the size distribution of the suspended solids remained almost constant when the hydrolyzed suspension was subjected to intensive mixing. It was also found that the average specific cake resistance was successfully reduced by the use of filter aids. This reduction depended on the method of how the filter aids were applied. In order to obtain high filtration capacity, it is recommended to use the body feed mode, i.e. to mix the filter aid with the slurry prior to filtration. Regarding the quality of the filtrate, precoat filtration was observed to produce a clear filtrate with negligible suspended solids content, while the body feed filtrates were turbid, irrespective of which type of filter aid was used.

Production of Chemicals from Woody Biomass by Wet Oxidation

The production of chemicals from sawdust by wet oxidation has been investigated. Two different concentrations of sawdust; 54054 mg/l and 32683 mg/l were used in the study. The wet oxidation operating conditions were; 175 deg.C – 225 deg.C, 1MPa Oxygen, and 40 minutes to 120 minutes reaction time. Carboxylic acids were among the chemicals produced in the process. The total yield of carboxylic acids was found to increase with temperature. Also, higher yields of carboxylic acids were observed at a lower sawdust concentration. This was probably due to the high oxygen-biomass ratio at lower sawdust concentration. Higher oxygen availability at low sawdust concentration resulted in increased conversion of the sawdust; hence the higher yields of carboxylic acids. At lower sawdust concentration, a total carboxylic acid yield of 25.59 wt% was attained at 200 deg.C and 40 minutes reaction time. At higher sawdust concentration, a total carboxylic acid yield of 15.57 wt% was attained at 200 deg.C and 40-minutes reaction time. The carboxylic acids identified include formic acid, acetic acid, succinic acid and oxalic acid. The optimum temperature for the production of formic acid was found to be 200 deg.C, while the optimum temperature for the production of acetic acid was found to be 225 deg.C. A temperature of 225 deg.C and relatively short reaction time of 10 minutes was found to be the optimal condition for the production of succinic acid. Formic acid was produced in the highest yield, with an optimal yield of 13.69wt %, when the reaction temperature and time are 200 deg.C and 40 minutes respectively. The yield of formic acid was found to decrease significantly when further increasing the temperature to 225 deg.C. This was presumably due to thermal decomposition of formic acid at relatively higher temperature. However, the yield of acetic acid was found to steadily increase with temperature. This is because acetic is more thermally stable than formic acid. The yield of acetic acid did not decrease after the temperature was increased to 225 deg.C. Optimal yield of acetic acid (7.98wt %) was achieved at; 225 deg.C, and 40 minutes reaction time. Succinic acid was produced only at temperatures of 200 deg.C and 225 deg.C. Optimal yield of succinic acid (5.66wt %) was attained under the following conditions; 32683 mg/l, 225 deg.C, 1MPa O2, and 10-minutes reaction time. Oxalic acid was produced in the lowest yield and, less frequently. The optimal yield of oxalic acid (4.02 wt%) was attained at 175 deg.C and 80-minutes of reaction time The Total Organic Carbon (TOC) is found to be higher when increasing the operating temperature, thus suggesting that more organic compounds are formed at higher temperatures. The identified carboxylic acids could only account for less than 30% of the measured COD content of the various wet oxidation samples. This implies that some other unidentified compounds (reaction products) must have been present. In general, wet oxidation seems to be an effective method for converting lignocellulosic biomass into useful chemicals. Relatively higher temperatures have been found to favor the production of carboxylic acids from sawdust.

Topochemistry of physical and chemical pretreatments of biomass as investigated by FE-SEM, XPS and ToF-SIMS

Surface chemistry is of great importance in plant biomass engineering and applications. The surface chemical composition of biomass which includes lignin, carbohydrates and extractives influences its interactions with chemical agents, such as pulp processing/papermaking chemicals, or enzymes for different purposes. In this thesis, the changes in the surface chemical composition of lignocellulosic biomass after physical modification for the improvement of resulting paper properties and chemical treatment for the enhancement of enzymatic hydrolysis were investigated. Low consistency (LC) refining was used as physical treatment of bleached softwood and hardwood pulp samples, and the surface chemistry of refined samples was investigated. The refined pulp was analysed as whole pulp while the fines-free fibre samples were characterized separately. The fines produced in LCrefining contributed to an enlarged surface specific area as well as the change of surface coverage by lignin and extractives, as investigated by X-ray photoelectron spectroscopy (XPS). The surface coverage by lignin of the whole pulp decreased after refining while the surface coverage by extractives increased both for pine and eucalyptus. In the case of pine, the removal of fines resulted in reduction of the surface coverage by extractives, while the surface coverage by lignin increased on fibre sample (without fines). In the case of eucalyptus, the surface coverage by lignin of fibre samples decreased after the removal of fines. In addition, the surface distribution of carbohydrates, lignin and extractives of pine and eucalyptus samples was determined by Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). LC-refining increased the amounts of pentose, hexose and extractives on the surface of pine samples. ToF-SIMS also gave clear evidence about xylan deposition and reduction of surface lignin distribution on the fibre of eucalyptus. However, the changes in the surface chemical composition during the physical treatment has led to an increase in the adsorption of fluorescent whitening agents (FWAs) on fibres due to a combination of electro-static forces, specific surface area of fibres and hydrophobic interactions. Various physicochemical pretreatments were conducted on wood and non-wood biomass for enhancing enzymatic hydrolysis of polysaccharides, and the surface chemistry of the pretreated and enzymatically hydrolysed samples was investigated by field emission scanning electron microscopy (FE-SEM), XPS and ToF-SIMS. A hydrotrope was used as a relatively novel pretreatment technology both in the case of wood and non-wood biomass. For comparison, ionic liquid and hydrothermal pretreatments were applied on softwood and hardwood as well. Thus, XPS analysis showed that the surface lignin was more efficiently removed by hydrotropic pretreatment compared to ionic liquid or hydrothermal pretreatments. SEM analysis also found that already at room temperature the ionic liquid pretreatments were more effective in swelling the fibres compared with hydrotropic pretreatment at elevated temperatures. The enzymatic hydrolysis yield of hardwood was enhanced due to the decrease in surface coverage of lignin, which was induced by hydrotropic treatment. However, hydrotropic pretreatment was not appropriate for softwood because of the predominance of guaiacyl lignin structure in this material. In addition, the reduction of surface lignin and xylan during pretreatment and subsequent increase in cellulose hydrolysis by enzyme could be observed from ToF-SIMS results. The characterisation of the non-wood biomass (e.g. sugarcane bagasse and common reed) treated by hydrotropic method, alkaline and alkaline hydrogen peroxide pretreatments were carried out by XPS and ToF-SIMS. According to the results, the action for the removal of the surface lignin of non-wood biomass by hydrotropic pretreatment was more significant compared to alkaline and alkaline hydrogen peroxide pretreatments, although a higher total amount of lignin could be removed by alkaline and alkaline hydrogen peroxide pretreatment. Furthermore, xylan could be remarkably more efficiently removed by hydrotropic method. Therefore, the glucan yield achieved from hydrotropic treated sample was higher than that from samples treated with alkaline or alkaline hydrogen peroxide. Through the use of ToF-SIMS, the distribution and localization of lignin and carbohydrates on the surface of ignocelluloses during pretreatment and enzymatic hydrolysis could be detected, and xylan degradation during enzymatic hydrolysis could also be assessed. Thus, based on the results from XPS and ToF-SIMS, the mechanism of the hydrotropic pretreatment in improving the accessibility of enzymes to fibre and further ameliorating of the enzymatic saccharification could be better elucidated.

Comparison of model-based above ground biomass predictions from LiDAR

In order to reduce greenhouse emissions from forest degradation and deforestation the international programme REDD (Reducing Emissions from Deforestation and forest Degradation) was established in 2005 by the United Nations Framework Convention on Climate Change (UNFCCC). This programme is aimed to financially reward to developing countries for any emissions reductions. Under this programm the project of setting up the payment system in Nepal was established. This project is aimed to engage local communities in forest monitoring. The major objective of this thesis is to compare and verify data obtained from di erect sources - remotely sensed data, namely LiDAR and field sample measurements made by two groups of researchers using two regression models - Sparse Bayesian Regression and Bayesian Regression with Orthogonal Variables.