Effects of mineral sorting on concentrator design and economics

Ore sorting after crushing is an effective way to enhance the feed quality of a concentrator. Sorting by hand is the oldest way of concentrating minerals but it has become outdated because of low capacities. Older methods of sorting have also been difficult to use in large scale productions due to low capacities of sorters. Data transfer and processing and the speed of rejection mechanisms have been the bottlenecks for effective use of sorters. A fictive chalcopyrite ore body was created for this thesis. The properties of the ore were typical of chalcopyrite ores and economical limit was set for design. Concentrator capacity was determined by the size of ore body and the planned mine life. Two concentrator scenarios were compared, one with the sorting facility and the other without sorting. Comparison was made for quality and amount of feed, size of equipment and economics. Concentrator with sorting had lower investment and operational cost but also lower incomes due to the ore loss in sorting. Net cash flow, net present value and internal rate of interest were calculated for comparison of the two scenarios.

Puristussylinterien valmistuksen kehittäminen

Tässä diplomityössä kehitettiin yksitoimisten puristussylinterien valmistusta Rautessa. Sylinterien valmistuksessa haastavin vaihe on sylinteriputken ja pohjan välinen hitsaus. Hitsauksen avuksi suunniteltiin sylinterin sisäpuolinen juuritukilaite. Hitsauskokeita suoritettiin hitsin pohjan jauhekaarihitsaukselle ja MAG-hitsaukselle. Juuritukilaitteen toimivuutta testattiin koehitsauksilla. Puristussylinterien materiaali on S355J2-terästä, jonka ainevahvuus on 20 – 60 mm. Paksujen rakenneterästen hitsauksessa täytyy ottaa huomioon hitsausliitoksen mekaanisten ominaisuuksien muuttuminen sekä eri halkeamien synty. Hitsauksen laatuun ja laadunhallintaan voidaan vaikuttaa monien eri tekijöiden avulla. Hitsausohjeen avulla, ja muut laatutekijät huomioiden, voidaan hitseille asetetut laatukriteerit täyttää. Juurituen käyttö nopeuttaa puristussylinterien hitsausta vähintään 50 %. Jauhekaarihitsaus kuparista juuritukea vasten synnyttää vaikeasti poistettavan kuonan juuren puolelle. Perinteinen MAG-hitsaus kuparista juuritukea vasten sisältää liian monta muuttujaa, mikä tekee siitä epäluotettavan pohjapalon hitsaukseen. Työssä suunnitellun juuritukilaitteen käyttö tuotannossa vaatii lisää hitsauskokeita.

Open innovation: university-industry interaction in Russia

Innovation nowadays is one of the key elements of counties’ competitiveness. In the face of continuous world economic changes, open innovation business model implementation allows many companies to improve and accelerate their innovation processes through collaboration. Universities as traditional sources of knowledge might be involved in such kind of collaboration. In developing countries, which are in transition towards innovation-based economy, as Russia, open innovation business model can serve as a tool to speed up this transition. The Master’s Thesis explores the implementation of open innovation model in collaboration between companies and universities in global scale and particularly in Russia. The study is qualitative and it is based on integrative analysis of literature, secondary data and results of the survey, conducted among Russian universities. In the thesis a model for implementation of open innovation into Triple Helix model is elaborated. The study also explores not very common practice of reverse-directional interaction - from industry to university. The findings of this research show a necessity of solving the identified problems in parallel with implementation of open innovation concept in university-industry collaboration.

Vauhtikausi. Autoilun sukupuoli 1920-luvun Suomessa

The Age of Speed:Automobility’s Gender in the 1920s Finland The aim of this study is to analyze the connections between automobility and gender in Finland in the 1920s. In this study it is argued that the 1920s was the significant era in the Finnish history of automobility when many of the long-lasting gendered notions and cultural understandings were constructed. This study combines cultural history of technology with gender analysis. As the previous research on gender and technology has recognized, technology is a significant site of gender negotiations. Both from the cultural historical perspective and a gender perspective it is important to understand both technology and gender as cultural constructions. They were linked together and constructed each other. In other words: technology shapes gender and gender shapes technology. Historians of technology like Nina Lerman, Ruth Oldenziel and Arwen Mohun have argued that both gender and technology are about power: social, cultural, economic and political. In this study automobility means technology that can be analyzed in layers of identity, structures, institutions and representations. The source material consists of various types of historical sources, magazines and journals, advertisements, archival material together with films and literature. In the previous studies of the history of automobility gender has often been neglected. The term “gender” has also quite often been misunderstood. Some studies in the field have only focused on the early female drivers. However, far too little attention has been paid to the question, why automobility was considered as masculine sphere only. This study aims to give new insights to the previous interpretations of the history of automobility. As in various other countries also in Finland, the decade of the 1920s is characterized as a period of “modern times.” It was also the era of the automobiles. Although the number of cars in Finland was still low compared to the other European countries and the USA, in press, films and literature, images of automobiles and new women – and men – on the wheel became as an emblem of a new era. The thesis consists of three main chapters. The first main chapter focuses on the conflicts between drivers and non-drivers. The study shows how in the debate of the automobility “a driver” was constantly referred as a man and “a pedestrian” accordingly a woman, even though in the reality there were as much men and women walking on the streets and the roads. Thus, the public debate constructed and reconstructed the gendered traffic system where men were playing the key role. The second main chapter of the study analyses the automobile clubs and the cultural representations. The chapter answers the question how the concept of a driver was gendered. The Automobile clubs and the organizations of professional drivers were in a significant role in developing the early history of traffic in Finland. The Finnish Automobile Club (Suomen Automobiili Klubi, founded in 1919) was the oldest and the most powerful of all automobile organizations. The Finnish Automobile Club accepted women as members from the very beginning. The membership was strictly limited to the upper class and the very first female members were wives and daughters of the male members. However, Doctor of medicine and surgery 316 Karolina Eskelin (1867-1936) the founding member of the Club was an exception to that convention. The male members of the Finnish Automobile Club attended official international meetings and consulted Finnish authorities in traffic and road questions, whereas, female members joined car trips, picnics and social gatherings arranged by the club. Few young female members of the club drove in races and gross-country-tours. The cultural representations of drivers in the Finnish media in the 1920s both deconstructed and reconstructed the concept of gender. In Finnish press in general, motoring was seen as male dominated area. Men were represented as the experts of the automobility. The drivers’ uniforms and the automobile clubs underlined professionalism and expertise which, thus, got masculine meaning. Women were beautiful accessories in the car ads, but they were also becoming a new consumer group in the market. The representations of the female and the male drivers influenced and shaped actively the understandings of femininity and masculinity. In the third main chapter the analysis focuses on the automobile as an artifact.The automobile was considered as an artifact that primarily belonged to the masculine domain. However, the representations of the automobiles were ambivalent. The automobile was both masculine and feminine depending on the context. The representations of the automobile were also used to construct the discourse of heteronormativity.

Combination of pulsed corona discharge with TiO2 photocatalysis: verification of hypothesis

The oxidation potential of pulsed corona discharge concerning aqueous impurities is limited in respect to certain refractory compounds. This may be enhanced in combination of the discharge with catalysis/photocatalysis as developed in homogeneous gas-phase reactions. The objective of the work consists of testing the hypothesis of oxidation potential enhancement in combination of the discharge with TiO2 photocatalysis applied to aqueous solutions of refractory oxalate. Meglumine acridone acetate was included for meeting the practical needs. The experimental research was undertaken into oxidation of aqueous solutions under conditions of various target pollutant concentrations, pH and the pulse repetition rate with plain electrodes and the electrodes with TiO2 attached to their surface. The results showed no positive influence of the photocatalyst, the pollutants were oxidized with the rate identical within the accuracy of measurements. The possible explanation for the observed inefficiency may include low UV irradiance, screening effect of water and generally low oxidation rate in photocatalytic reactions. Further studies might include combination of electric discharge with ozone decomposition/radical formation catalysts.

Kiteen mekaanisten värähtelyjen vaimentaminen takaisinkytkennällä

Pulseri on laite, joka tuottaa noin 10 MHz:n taajuudella olevan sähköisen pulssin, joka ohjataan kiteeseen. Kide lähettää korkeataajuuksisen ääniaallon ja toimii samalla vastaanottimena kaikuna heijastuneille ääniaalloille. Kide ja membraanikalvo ovat vedessä. Ääniaalto heijastuu takaisin suodatusmembraanikalvosta, jolla on tarkoitus erotella epäpuhtauksia. Membraanikalvo ja kide ovat millimetrin etäisyydellä toisistaan ja ääniaalloilla kestää noin 1,3 mikrosekuntia kulkea kiteestä membraanikalvon pinnalle ja siitä kaikuna takaisin kiteeseen. Saadaksemme luotettavia tuloksia ääniaallon kulkuajasta, kiteen tulee olla värähtelemättömässä tilassa silloin, kun kaikuna palaava pulssi saapuu takaisin. Työssä keskitytään kiteen vaimentamiseen mahdollisimman nopeasti lähetetyn pulssin jälkeen ja siihen liittyviin ongelmiin.

“Development work thesis” as a tool for continuing professional education

Julkaisumaa: 158 TW TWN Taiwan

Suurnopeuspumput

Suurnopeustekniikasta on tehty tutkimusta 1980-luvulta lähtien. On havaittu, että tiettyjen energiateknisten sovellusten hyötysuhde paranee, kun käytetään selkeästi tavanomaista suurempaa pyörimisnopeutta. Suurnopeuspumppuja on totuttu näkemään lähinnä erikoiskohteissa, kuten avaruustekniikassa. Tämän työn tarkoituksena on kartoittaa, voiko suurnopeuspumppuja käyttää tavallisissa teollisuussovelluksissa, joissa tarvitaan korkeapaineista vettä. Työssä selvitetään pumppujen laskentaan ja valintaan liittyvää käsitteistöä, sekä luodaan kirjallisuuskatsaus suurnopeuspumppujen kehitykseen. Työn tarkoituksena on myöskin luoda valmiuksia suurnopeuspumppujen tutkimukseen ja arviointiin.

Optimization of parameters for fiber laser-MAG hybrid welding in shipbuilding applications

The Arctic region becoming very active area of the industrial developments since it may contain approximately 15-25% of the hydrocarbon and other valuable natural resources which are in great demand nowadays. Harsh operation conditions make the Arctic region difficult to access due to low temperatures which can drop below -50 °C in winter and various additional loads. As a result, newer and modified metallic materials are implemented which can cause certain problems in welding them properly. Steel is still the most widely used material in the Arctic regions due to high mechanical properties, cheapness and manufacturability. Moreover, with recent steel manufacturing development it is possible to make up to 1100 MPa yield strength microalloyed high strength steel which can be operated at temperatures -60 °C possessing reasonable weldability, ductility and suitable impact toughness which is the most crucial property for the Arctic usability. For many years, the arc welding was the most dominant joining method of the metallic materials. Recently, other joining methods are successfully implemented into welding manufacturing due to growing industrial demands and one of them is the laser-arc hybrid welding. The laser-arc hybrid welding successfully combines the advantages and eliminates the disadvantages of the both joining methods therefore produce less distortions, reduce the need of edge preparation, generates narrower heat-affected zone, and increase welding speed or productivity significantly. Moreover, due to easy implementation of the filler wire, accordingly the mechanical properties of the joints can be manipulated in order to produce suitable quality. Moreover, with laser-arc hybrid welding it is possible to achieve matching weld metal compared to the base material even with the low alloying welding wires without excessive softening of the HAZ in the high strength steels. As a result, the laser-arc welding methods can be the most desired and dominating welding technology nowadays, and which is already operating in automotive and shipbuilding industries with a great success. However, in the future it can be extended to offshore, pipe-laying, and heavy equipment industries for arctic environment. CO2 and Nd:YAG laser sources in combination with gas metal arc source have been used widely in the past two decades. Recently, the fiber laser sources offered high power outputs with excellent beam quality, very high electrical efficiency, low maintenance expenses, and higher mobility due to fiber optics. As a result, fiber laser-arc hybrid process offers even more extended advantages and applications. However, the information about fiber or disk laser-arc hybrid welding is very limited. The objectives of the Master’s thesis are concentrated on the study of fiber laser-MAG hybrid welding parameters in order to understand resulting mechanical properties and quality of the welds. In this work only ferrous materials are reviewed. The qualitative methodological approach has been used to achieve the objectives. This study demonstrates that laser-arc hybrid welding is suitable for welding of many types, thicknesses and strength of steels with acceptable mechanical properties along very high productivity. New developments of the fiber laser-arc hybrid process offers extended capabilities over CO2 laser combined with the arc. This work can be used as guideline in hybrid welding technology with comprehensive study the effect of welding parameter on joint quality.

Aktiivisen verkkosillan tuottaman yhteismuotoisen jännitteen vaimentaminen kaksitasoisessa, jännitevälipiirillisessä, taajuusmuuttajatopologiassa

Pulssinleveysmoduloidun vaihtosuuntaajan hyötysuhteen parantaminen ja kytkentätaajuuden suurentaminen ovat johtaneet lähtöjännitteen suuritaajuiseen taajuussisältöön kaksitasoisessa, jännitevälipiirillisessä taajuusmuuttajatopologiassa. Kasvava tarve siirtää tehoa myös verkkoon päin on lisännyt aktiivisen verkkosillan käyttöä. Kaksitasoisen aktiivisen verkkosillan vaikutuksesta DC-välipiirin keskipisteen ja kolmivaiheisen kuorman tähtipisteen välinen jännite on nollasta poikkeava aiheuttaen suurentuneen yhteismuotoisen jännitteen taajuusmuuttajan lähtöön ja verkon puolelle. Lisäksi yhteismuotoisten jännitteiden aiheuttamat kytkentätaajuiset häiriövirrat voivat aiheuttaa vikavirtasuojien tahatonta laukeamista, vaikeuttaa EMC-standardien vaatimusten täyttämistä, lisätä moottorin käämieristyksien rasitusta ja mahdollisuutta moottorin laakerivaurioille. Diplomityössä tutkitaan aktiivisen ja passiivisen verkkosillan tuottamaa yhteismuotoista jännitettä simuloinneilla. Esitellään aikaisempaa tutkimustietoa yhteismuotoisen jännitteen ja virran vaimennusratkaisuista aktiivista verkkosiltaa käytettäessä. Tutkimustiedon pohjalta suunnitellaan koelaitteistolle soveltuva suodin. Suotimen toiminta testataan simuloinnein sekä kokeellisin mittauksin. Tehdyt mittaukset osoittavat, että suunniteltu suodin vaimentaa yhteismuotoista jännitettä noin 20 dB verkkosillan kytkentätaajuudella ja tämän jälkeen yli 20 dB/dekadi taajuuteen 100 kHz asti. Lisäksi yhteismuotoisen virran suuruus syöttökaapelin kautta pieneni ehdotetun suotimen vaikutuksesta.

Characterization Of Process Efficiency Improvement In Laser Additive Manufacturing

Laser additive manufacturing (LAM), known also as 3D printing, has gained a lot of interest in past recent years within various industries, such as medical and aerospace industries. LAM enables fabrication of complex 3D geometries by melting metal powder layer by layer with laser beam. Research in laser additive manufacturing has been focused in development of new materials and new applications in past 10 years. Since this technology is on cutting edge, efficiency of manufacturing process is in center role of research of this industry. Aim of this thesis is to characterize methods for process efficiency improvements in laser additive manufacturing. The aim is also to clarify the effect of process parameters to the stability of the process and in microstructure of manufactured pieces. Experimental tests of this thesis were made with various process parameters and their effect on build pieces has been studied, when additive manufacturing was performed with a modified research machine representing EOSINT M-series and with EOS EOSINT M280. Material used was stainless steel 17-4 PH. Also, some of the methods for process efficiency improvements were tested. Literature review of this thesis presents basics of laser additive manufacturing, methods for improve the process efficiency and laser beam – material- interaction. It was observed that there are only few public studies about process efficiency of laser additive manufacturing of stainless steel. According to literature, it is possible to improve process efficiency with higher power lasers and thicker layer thicknesses. The process efficiency improvement is possible if the effect of process parameter changes in manufactured pieces is known. According to experiments carried out in this thesis, it was concluded that process parameters have major role in single track formation in laser additive manufacturing. Rough estimation equations were created to describe the effect of input parameters to output parameters. The experimental results showed that the WDA (width-depth-area of cross-sections of single track) is correlating exponentially with energy density input. The energy density input is combination of the input parameters of laser power, laser beam spot diameter and scan speed. The use of skin-core technique enables improvement of process efficiency as the core of the part is manufactured with higher laser power and thicker layer thickness and the skin with lower laser power and thinner layer thickness in order to maintain high resolution. In this technique the interface between skin and core must have overlapping in order to achieve full dense parts. It was also noticed in this thesis that keyhole can be formed in LAM process. It was noticed that the threshold intensity value of 106 W/cm2 was exceeded during the tests. This means that in these tests the keyhole formation was possible.

Design of a 1 kW 150 rpm permanent-magnet synchronous generator for stand-alone wind-power applications

A program for calculating low-speed low-power synchronous machine is presented. A permanent-magnet synchronous generator for 1 kW 150 rpm is designed. Optimization of magnet’s and coil’s dimensions was made.

It’s a workflow engine. It’s working with linked data. It’s repository! – Supporting electronic thesis related processes in University of Helsinki library

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

E-thesis repository – processes and data

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Influence of reactant absorption and dissolution in heterogeneous precipitation processes

In this research work, the aim was to investigate the volumetric mass transfer coefficient [kLa] of oxygen in stirred tank in the presence of solid particle experimentally. The kLa correlations as a function of propeller rotation speed and flow rate of gas feed were studied. The O2 and CO2 absorption in water and in solid-liquid suspensions and heterogeneous precipitation of MgCO3 were thoroughly examined. The absorption experiments of oxygen were conducted in various systems like pure water and in aqueous suspensions of quartz and calcium carbonate particles. Secondly, the precipitation kinetics of magnesium carbonate was also investigated. The experiments were performed to study the reactive crystallization with magnesium hydroxide slurry and carbon dioxide gas by varying the feed rates of carbon dioxide and rotation speeds of mixer. The results of absorption and precipitation are evaluated by titration, total carbon (TC analysis), and ionic chromatrography (IC). For calcium carbonate, the particle concentration was varied from 17.4 g to 2382 g with two size fractions: 5 µm and 45-63 µm sieves. The kLa and P/V values of 17.4 g CaCO3 with particle size of 5µm and 45-63 µm were 0.016 s-1 and 2400 W/m3. At 69.9 g concentration of CaCO3, the achieved kLa is 0.014 s-1 with particle size of 5 µm and 0.017 s-1 with particle size of 45 to 63 µm. Further increase in concentration of calcium carbonate, i.e. 870g and 2382g , does not affect volumetric mass transfer coeffienct of oxygen. It could be concluded from absorption results that maximum value of kLa is 0.016 s-1. Also particle size and concentration does affect the transfer rate to some extend. For precipitation experiments, the constant concentration of Mg(OH)2 was 100 g and the rotation speed varied from 560 to 750 rpm, whereas the used feed rates of CO2 were 1 and 9 L/min. At 560 rpm and feed rate of CO2 is 1 L/min, the maximum value of Mg ion and TC were 0.25 mol/litre and 0.12 mol/litre with the residence time of 40 min. When flow rate of CO2 increased to 9 L/min with same 560 rpm, the achieved value of Mg and TC were 0.3 mol/litre and 0.12 mol/L with shorter residence time of 30 min. It is concluded that feed rate of CO2 is dominant in precipitation experiments and it has a key role in dissociation and reaction of magnesium hydroxide in precipitation of magnesium carbonate.