Magnetic and transport properties of II-V diluted magnetic semiconductors doped with manganese and nickel

This thesis is devoted to investigations of three typical representatives of the II-V diluted magnetic semiconductors, Zn1-xMnxAs2, (Zn1-xMnx)3As2 and p-CdSb:Ni. When this work started the family of the II-V semiconductors was presented by only the compounds belonging to the subgroup II3-V2, as (Zn1-xMnx)3As2, whereas the rest of the materials mentioned above were not investigated at all. Pronounced low-field magnetic irreversibility, accompanied with a ferromagnetic transition, are observed in Zn1-xMnxAs2 and (Zn1-xMnx)3As2 near 300 K. These features give evidence for presence of MnAs nanosize magnetic clusters, responsible for frustrated ground magnetic state. In addition, (Zn1-xMnx)3As2 demonstrates large paramagnetic response due to considerable amount of single Mn ions and small antiferromagnetic clusters. Similar paramagnetic system existing in Zn1-xMnxAs2 is much weaker. Distinct low-field magnetic irreversibility, accompanied with a rapid saturation of the magnetization with increasing magnetic field, is observed near the room temperature in p- CdSb:Ni, as well. Such behavior is connected to the frustrated magnetic state, determined by Ni-rich magnetic Ni1-xSbx nanoclusters. Their large non-sphericity and preferable orientations are responsible for strong anisotropy of the coercivity and saturation magnetization of p- CdSb:Ni. Parameters of the Ni1-xSbx nanoclusters are estimated. Low-temperature resistivity of p-CdSb:Ni is governed by a hopping mechanism of charge transfer. The variable-range hopping conductivity, observed in zero magnetic field, demonstrates a tendency of transformation into the nearest-neighbor hopping conductivity in non-zero magnetic filed. The Hall effect in p-CdSb:Ni exhibits presence of a positive normal and a negative anomalous contributions to the Hall resistivity. The normal Hall coefficient is governed mainly by holes activated into the valence band, whereas the anomalous Hall effect, attributable to the Ni1-xSbx nanoclusters with ferromagnetically ordered internal spins, exhibits a low-temperature power-law resistivity scaling.

The Role of Integrins in Enterovirus Infections and in Metastasis of Cancer

Integrins are a family of transmembrane glycoproteins, composed of two different subunits (alpha and beta). Altered expression of integrins in tumor cells contributes to metastasis tendency by influencing on the cells‟ attachment to adjacent cells and their migration. Viral pathogens, including certain enteroviruses, use integrins as receptors. Enteroviruses have also been suggested to be involved in the etiopathogenesis of type 1 diabetes. The study focuses on the role of integrins in the pathogenesis of metastasis to cortical bone and on type 1 diabetes (T1D) and echovirus 1 infection. In the first part of the thesis, the role of different integrins in the initial attachment of MDA-MD-231 breast cancer cells to bovine cortical bone disks was studied. A close correlation between alpha2beta1 and alpha3beta1 integrin receptor expression and the capability of the tumor to attach to bone were observed. In the second part, a possible correlation between susceptibility to enterovirus infections in diabetic children and differences in enterovirus receptor genes, including certain integrins, was investigated. In parallel, virus-specific neutralizing antibodies and diabetic risk alleles were studied. In the diabetic group, an amino acid change was detected in the polio virus receptor and the neutralizing antibody titers against echovirus 30 were lower. However, to obtain statistically sustainable results, a larger number of individuals should be analyzed. Echovirus 1 (EV1) enters cells by attaching to the alpha2I domain of the alpha2beta1 integrin. In the third part EV1 was shown to attach to a chimeric receptor construct of the transferrin receptor and the alpha2I domain and to enter cells through clathrin-mediated endocytosis that is normally not used by the virus. The chimeric receptor was recycled to the plasma membrane, whereas the virus remained in intracellular vesicles. The virus replication cycle was initiated in these cells, suggesting that evolution pressure could possibly cause the virus to evolve to use a different entry mechanism. Moreover, a cDNA microarray analysis of host gene expression during EV1 replication showed that 0.53% of the total genes, including several immediate early genes, were differently expressed.

Parallel-Operating Three-Phase Voltage Source Inverters – Circulating CurrentModeling, Analysis and Mitigation

The maximum realizable power throughput of power electronic converters may be limited or constrained by technical or economical considerations. One solution to this problemis to connect several power converter units in parallel. The parallel connection can be used to increase the current carrying capacity of the overall system beyond the ratings of individual power converter units. Thus, it is possible to use several lower-power converter units, produced in large quantities, as building blocks to construct high-power converters in a modular manner. High-power converters realized by using parallel connection are needed for example in multimegawatt wind power generation systems. Parallel connection of power converter units is also required in emerging applications such as photovoltaic and fuel cell power conversion. The parallel operation of power converter units is not, however, problem free. This is because parallel-operating units are subject to overcurrent stresses, which are caused by unequal load current sharing or currents that flow between the units. Commonly, the term ’circulatingcurrent’ is used to describe both the unequal load current sharing and the currents flowing between the units. Circulating currents, again, are caused by component tolerances and asynchronous operation of the parallel units. Parallel-operating units are also subject to stresses caused by unequal thermal stress distribution. Both of these problemscan, nevertheless, be handled with a proper circulating current control. To design an effective circulating current control system, we need information about circulating current dynamics. The dynamics of the circulating currents can be investigated by developing appropriate mathematical models. In this dissertation, circulating current models aredeveloped for two different types of parallel two-level three-phase inverter configurations. Themodels, which are developed for an arbitrary number of parallel units, provide a framework for analyzing circulating current generation mechanisms and developing circulating current control systems. In addition to developing circulating current models, modulation of parallel inverters is considered. It is illustrated that depending on the parallel inverter configuration and the modulation method applied, common-mode circulating currents may be excited as a consequence of the differential-mode circulating current control. To prevent the common-mode circulating currents that are caused by the modulation, a dual modulator method is introduced. The dual modulator basically consists of two independently operating modulators, the outputs of which eventually constitute the switching commands of the inverter. The two independently operating modulators are referred to as primary and secondary modulators. In its intended usage, the same voltage vector is fed to the primary modulators of each parallel unit, and the inputs of the secondary modulators are obtained from the circulating current controllers. To ensure that voltage commands obtained from the circulating current controllers are realizable, it must be guaranteed that the inverter is not driven into saturation by the primary modulator. The inverter saturation can be prevented by limiting the inputs of the primary and secondary modulators. Because of this, also a limitation algorithm is proposed. The operation of both the proposed dual modulator and the limitation algorithm is verified experimentally.

Studies on 68Ga-Based Agents for PET Imaging of Cancer and Inflammation

Studies on ⁶⁸Ga-Based Agents for PET Imaging of Cancer and Inflammation Positron emission tomography (PET) is based on the use of radiolabeled agents and facilitates in vivo imaging of biological processes, such as cancer. Because the detection of cancer is demanding and is often obscured by inflammation, there is a demand for better PET imaging agents. The aim was to preliminarily evaluate new PET agents for imaging cancer and inflammation using experimental models. ⁶⁸Ga-chloride and peptides, ⁶⁸Ga-labeled through 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid (DOTA), targeting matrix metalloproteinase-9 (MMP-9) were tested for tumor imaging. In addition, a ⁶⁸Ga-DOTA-conjugated peptide targeting vascular adhesion protein-1 (VAP-1), was tested for inflammation imaging. The ⁶⁸Ga-based imaging agents described here showed potential features by passing the essential in vitro tests, proceeding further to preclinical in vivo evaluation and being able to visualize the target. The target uptake and target-to-background ratios of ⁶⁸Ga-based agents were, however, not optimal. ⁶⁸Ga-chloride showed slow clearance caused by its binding to blood transferrin. In the case of ⁶⁸Ga-DOTA-peptides low in vivo stability and/or low lipophilicity led to too rapid blood clearance and urinary excretion. The properties of ⁶⁸Ga-labeled peptides are modifiable, as shown with matrix metalloproteinase-9 targeting ligands. In the conclusion of this PhD thesis, ⁶⁸Ga-based agents for PET imaging of cancer and inflammation could be applied in the development of drugs, earlier diagnostics and following-up of the efficacy of therapies.

Vuotasapainon hallinta kokosiltasyötetyssä muuntajassa

Keskitaajuudella toimivia muuntajia käytetään laajalti tehoelektroniikkasovelluksissa kuten DC/DC-konverttereissa ja muissa hakkuriteholähteissä. Muuntaja on induktiivinen komponentti, jonka magneettisen tasapainon säilyttäminen hakkuriteholähteissä on laitteen virheettömän toiminnan kannalta tärkeää. Muuntajaa syöttävän virtapiirin on muodostettava symmetrinen syöttöjännite, jotta muuntajan vuo ei ajaudu positiiviseen tai negatiiviseen kyllästykseen. Tässä diplomityössä esitetään muuntajan sähkömagneettinen toimintaperiaate, kyllästymisen syyt hakkuriteholähteissä sekä kehitetään aktiivinen ohjaus vuotasapainon säilyttämiseksi. Hakkuriteholähteissä käytettävissä muuntajissa on monesti useampi kuin kaksi käämiä. Tässä työssä tutkittavassa muuntajassa on useita ensiöitä ja useita toisioita ja muuntajaa syötetään keskitaajuudella. Tämä tuo uusia ongelmia verrattuna perinteiseen yksivaiheiseen DC/DC-konvertteriin. Näihin ongelmiin esitetään ratkaisut diplomityön tutkimuksessa.

Ferromagnetic properties of pyrolytic nanocarbon

The work reported in this thesis is dedicated to irreversible magnetic properties in pyrolytic nanocarbon samples. Based on atomic force microscope images, the samples consist of carbon clusters with radius 30..120 nm. These are treated as single-domain nanoparticles. Magnetic hysteresis, field cooled, zero field cooled and thermoremanent magnetization measurements were performed using an RF SQUID magnetometer and ferromagnetic behaviour was observed. Analysis suggests that the ferromagnetic ordering is associated with defects in a thin surface layer, whose thickness is independent of particle size. Critical radius for single-domain particles, critical radius for coherent rotation, magnetic layer thickness, distance between elementary magnetic moments, saturation magnetization, exchange stiffness constant and anisotropy energy density are also presented.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.

Design of salient pole PM synchronous machines for a vehicle traction application – Analysis and

This doctoral thesis presents a study on the development of a liquid-cooled frame salient pole permanent-magnet-exited traction machine for a four-wheel-driven electric car. The emphasis of the thesis is put on a radial flux machine design in order to achieve a light-weight machine structure for traction applications. The design features combine electromagnetic and thermal design methods, because traction machine operation does not have a strict operating point. Arbitrary load cycles and the flexible supply require special attention in the design process. It is shown that accurate modelling of the machine magnetic state is essential for high-performance operation. The saturation effect related to the cross-saturation has to be taken carefully into account in order to achieve the desired operation. Two prototype machines have been designed and built for testing: one totally enclosed machine with a special magnet module pole arrangement and another through-ventilated machine with a more traditional embedded magnet structure. Both structures are built with magnetically salient structures in order to increase the torque production capability with the reluctance torque component. Both machine structures show potential for traction usage. However, the traditional embedded magnet design turns out to be mechanically the more secure one of these two machine options.

Kompostipiireissä opittua : Eloperäiset jätteet kiertoon -hanke

Kompostien käyttöä on kokeiltu ja tutkittu Kainuun ELY-keskuksen Eloperäiset jätteet kiertoon -hankkeessa. Komposteja on hyödynnetty laskettelurinteen ja kaivosteollisuuden sivukiven läjitysalueen maisemoinnissa, pihanurmen ja energiakasvien kasvattamisessa, metsän lannoittamisessa ja maanviljelyssä. Pihanurmen perustamisen ja energiakasvien kasvattamisen kokeiluista on tehty myös erilliset tutkimukset. Tutkimustyöstä on vastannut MTT (Maa- ja elintarviketalouden tutkimuskeskus). Tutkimustieto on sisällytetty tähän julkaisuun. Kompostin käyttökokeissa ja tutkimuksissa on hyödynnetty Kainuun kuntien ja Kainuun jätehuollon kuntayhtymän Eko-Kympin komposteja. Kaikki kompostit ovat aumakompostoinnin tuotoksia. Eko-Kympin komposti on valmistettu biojätteistä. Muut kompostit ovat lähtöisin kunnallisten jätevedenpuhdistamoiden lietteistä. Kajaanin kompostia kutsutaan myös A. & E. Juntunen Oy:n valmistamaksi biomullaksi. Saatujen kokemusten ja tutkimusten mukaan aumakompostoinnilla tuotettu komposti soveltuu näihin erilaisiin käyttömuotoihin, etenkin kun esille tulleita kehittämistoimia toteutetaan. Sivukiven läjitysalueiden maisemoinnissa, maanviljelyssä ja metsän lannoittamisessa komposti ei tarvitse kivennäismaata seosaineeksi. Sivukiven läjitysalueilla ne kompostit, joihin oli sekoitettu hiekkaa, eivät pysyneet paikoillaan. Aines valui sadeveden mukana alas rinteeltä. Pelkkää kompostia käytettäessä kompostimassa pysyi aloillaan. Maanviljelyssä ja metsän lannoittamisessa kivennäismaa on tarpeeton. Lisäksi kompostissa oleva kiviaines kuluttaa ja voi vaurioittaa levityslaitteita. Ravinteet vapautuvat kompostista hitaasti kasvien käyttöön. Kemiallisilla lannoitteilla on nopeampi vaikutus. Kompostit soveltuvat erityisen hyvin ympäristöihin, joissa täydennyslannoitusta ei tarvita tai joissa lannoite on vaikeaa levittää. Tällaisia kohteita ovat esimerkiksi kaivosten sivukiven tai rikastushiekan läjitysalueet tai muut vaikeakulkuiset kohteet. Myös metsien lannoittaminen ja maanviljely ovat Kainuussa kompostien hyödyntämisen osalta alihyödynnettyjä. Pöyry Finland Oy on laatinut Kajaaniin kaavaillulle biologiselle jätteiden käsittelylaitokselle teknistaloudelliset suunnitelmat. Yhtiön tekemissä suunnitelmissa tulee ilmi, että kaikkien Kainuun lietteiden aumakompostointi tuottaisi kompostia 13 000 tonnia vuodessa, kun tukiaine seulotaan erilleen. Mädätys- tai biokaasulaitosvaihtoehdoissa lopputuotteen määrä on edellistä pienempi. Pelkkien Kainuun lietteiden mädättäminen tuottaisi kompostia jälkikompostin seulonnan jälkeen 6 600 tonnia. Viherrakentaminen taajamissa on komposteille Kainuussa yleinen käyttömuoto. Sillä on kasvun edellytyksiä etenkin, kun kompostin laatuun panostetaan. Viherrakentaminen Kajaanin seudulla riittäisi kuluttamaan kaiken Kainuussa muodostuvan kompostin, kun kompostimullan kulutuksena pidetään 0,5 tonnia asukasta kohden vuodessa. Tämä vastaa Kajaanin seudulla 27 000 tonnin kompostimäärää. Kompostin muodostumismäärä ei tulevaisuudessa tule olemaan lähellä tätä laskennallista multamenekkiä. Kompostin huono menekki johtuu joidenkin kuntien osalta pikemminkin huonosta kompostin laadusta kuin markkinoiden kyllästymisestä. Tilanne on korjaantumassa suunnitteilla olevan biologisen jätteiden käsittelylaitoksen myötä. Siinä kompostituotteen laatuun voidaan panostaa tehokkaammin kuin erillisillä pienillä kompostointikentillä.

Towards novel biogas upgrading processes

Biogas production has considerable development possibilities not only in Finland but all over the world since it is the easiest way of creating value out of various waste fractions and represents an alternative source of renewable energy. Development of efficient biogas upgrading technology has become an important issue since it improves the quality of biogas and for example facilitating its injection into the natural gas pipelines. Moreover, such upgrading contributes to resolving the issue of increasing CO2 emissions and addresses the increasing climate change concerns. Together with traditional CO2 capturing technologies a new class of recently emerged sorbents such as ionic liquids is claimed as promising media for gas separations. In this thesis, an extensive comparison of the performance of different solvents in terms of CO2 capture has been performed. The focus of the present study was on aqueous amine solutions and their mixtures, traditional ionic liquids, ‘switchable’ ionic liquids and poly(ionic liquid)s in order to reveal the best option for biogas upgrading. The CO2 capturing efficiency for the most promising solvents achieved values around 50 - 60 L CO2 / L absorbent. These values are superior to currently widely applied water wash biogas upgrading system. Regeneration of the solvent mixtures appeared to be challenging since the loss of initial efficiency upon CO2 release was in excess of 20 - 40 vol %, especially in the case of aqueous amine solutions. In contrast, some of the ionic liquids displayed reversible behavior. Thus, for selected “switchable” ionic and poly(ionic liquid)s the CO2 absorption/regeneration cycles were performed 3 - 4 times without any notable efficiency decrease. The viscosity issue, typical for ionic liquids upon CO2 saturation, was addressed and the information obtained was evaluated and related to the ionic interactions. The occurrence of volatile organic compounds (VOCs) before and after biogas upgrading was studied for biogas produced through anaerobic digestion of waste waters sludge. The ionic liquid [C4mim][OAc] demonstrated its feasibility as a promising scrubbing media and exhibited high efficiency in terms of the removal of VOCs. Upon application of this ionic liquid, the amount of identified VOCs was diminished by around 65 wt %, while the samples treated with the aqueous mixture of 15 wt % N-methyldiethanolamine with addition of 5 wt % piperazine resulted in 32 wt % reduction in the amounts of volatile organic compounds only.

Tooth-Coil Permanent Magnet Synchronous Machine Design for Special Applications

This doctoral thesis presents a study on the design of tooth-coil permanent magnet synchronous machines. The electromagnetic properties of concentrated non-overlapping winding permanent magnet synchronous machines, or simply tooth-coil permanent magnet synchronous machines (TC-PMSMs), are studied in details. It is shown that current linkage harmonics play the deterministic role in the behavior of this type of machines. Important contributions are presented as regards of calculation of parameters of TC-PMSMs,particularly the estimation of inductances. The current linkage harmonics essentially define the air-gap harmonic leakage inductance, rotor losses and localized temporal inductance variation. It is proven by FEM analysis that inductance variation caused by the local temporal harmonic saturation results in considerable torque ripple, and can influence on sensorless control capabilities. Example case studies an integrated application of TC-IPMSMs in hybrid off-highway working vehicles. A methodology for increasing the efficiency of working vehicles is introduced. It comprises several approaches – hybridization, working operations optimization, component optimization and integration. As a result of component optimization and integration, a novel integrated electro-hydraulic energy converter (IEHEC) for off-highway working vehicles is designed. The IEHEC can considerably increase the operational efficiency of a hybrid working vehicle. The energy converter consists of an axial-piston hydraulic machine and an integrated TCIPMSM being built on the same shaft. The compact assembly of the electrical and hydraulic machines enhances the ability to find applications for such a device in the mobile environment of working vehicles.Usage of hydraulic fluid, typically used in working actuators, enables direct-immersion oil cooling of designed electrical machine, and further increases the torque- and power- densities of the whole device.

Sorbent characterization for circulating fluidized bed scrubbers

Harmful sulfur dioxide (SO2) emissions from power plants have increasingly been restricted since the 1970’s. Circulating fluidized bed (CFB) scrubber is a dry flue gas desulfurization method of absorbing SO2 out of the flue gas with sorbent. In current commercial plants, the used sorbent is commercial or on-site hydrated calcium hydroxide. The CFB scrubber process is characterized by a close but adequate approach to the flue gas saturation temperature that is achieved by spraying water to the absorber followed by a particulate control device. Very high SO2 removal is achieved along with a dry byproduct that is continuously recirculated back to the absorber for enhanced sorbent utilization. The aim of this work is to develop a method that would characterize the reactivity of sorbents used in CFB scrubbers and to conclude how different process parameters and sorbent properties affect the sulfur absorption. The developed characterization method is based on a fixed bed of sorbent and inert silica sand, through which an SO2 containing gas mixture is led. The reaction occurs in the bed and the SO2 concentration in the outlet as a function of time, a breakthrough curve, is obtained from the analyzer. Reactivity of the sorbents are evaluated by the absorbed sulfur amount. Results suggest that out of process parameters, lower SO2 concentration, lower temperature and higher moisture content enhance the desulfurization. Between different sorbents, specific surface area seems to be the most significant parameter. Large surface area linearly leads to more efficient desulfurization. Overall, the solid conversion levels in the tests were very low creating uncertainty to the validity of the results. New desing is being planned to overcome the problems of the device.

Industrial solution business – transition from product to solution offering

The business logic in the manufacturing industry has changed in the 21st century. In the current industrial market, manufacturers are driven to provide more comprehensive offerings that go beyond the traditional product-orientation by providing capacity and availability for their customers. From incidental merchandise, services have become the core of manufacturers’ offerings with long-lasting service agreements over the life-cycles of their products. This change is driven both by the need of providers to grow and gain competitive advantage and by increased customer demand caused by customers’ outsourcing trends. The three key drivers for manufacturers’ service strategies are outsourcing trends, saturation of the installed base, and commoditization in product markets. Thus, manufacturers focus on providing industrial solutions which are delivered through relational processes with customers by using solution-driven business models. In the management of marketing activities, this can be regarded as closer customer relationships, service-dominant business logic, and collaboration in solving customers’ problems. However, there are few studies on comprehensive conceptualizations of a solution offering that include different elements and their roles, especially in the context of capital goods industry. Also the transition process needs further studies in a real life context. This study explores the transition process of an industrial company from product to solution business and, as an aid to managing the solution business, explicates the structure and management of an industrial solution offering. There are two themes, the industrial transition process and industrial solution offering. Regarding the industrial transition process, the aim is to understand the supplier view on the process and its execution and to determine the challenges related to the transition process. The industrial solution offering is discussed by its elements and characteristics, as well as management. Furthermore, a special type of build-own-operate-transfer business model is presented and its suitability in the industrial context analyzed. The study includes findings achieved by qualitative methods and from four case companies. Based on the results, it is tentatively suggested that in the industrial solution business, the transition from product to solution business is not a linear project but an evolving process that varies according to customer needs, which suggests that companies need to possess an ability to develop new business models for different customer needs. The industrial solution offering is dynamic as it evolves in collaboration according to the prevailing and latent customer needs, which suggest restructuring of the organization from a product-centric to a customer-centric one. Furthermore, based on the findings, the concept of industrial solutions is defined as an ongoing relational process to satisfy a customer’s particular business or operational requirements, and the concept of industrial solution offering as an entity comprising the customized goods, services, collaboration, and finance needed to fulfill the industrial solution. Finally, the study offers several managerial implications for industrial managers involved in the transition and management of the solution business and its offering.

Direct-Driven Interior Magnet Permanent Magnet Synchronous Motors for a Full Electric Sports Car

The design process of direct-driven permanent magnet synchronous machines (PMSMs) for a full electric 4 ´ 4 sports car is presented. The rotor structure of the machine consists of two permanent magnet layers embedded inside the rotor laminations thus resulting in some inverse saliency, where the q-axis inductance is larger than the d-axis one. An integer slot stator winding was selected to fully take advantage of the additional reluctance torque. The performance characteristics of the designed PMSMs were calculated by applying a twodimensional finite element method. Cross-saturation between the d- and q-axes was taken into account in the calculation of the synchronous inductances. The calculation results are validated by measurements.

Magnetization studies of polystyrene/multiwall carbon nanotube composite films

Lappeenranta University of Technology School of Technology Technical Physics Evgenii Zhukov MAGNETIZATION STUDIES OF POLYSTYRENE/MULTIWALL CARBON NANOTUBE COMPOSITE FILMS Master’s thesis 2015 55 pages, 41 pictures, 9 Tables. Examiners: Professor Erkki Lähderanta D.Sc. Ivan Zakharchuk Keywords: polystyrene, multi-walled carbon nanotubes, MWCNT, composite, magnetization, SQUID. In this thesis magnetic properties of polystyrene/multiwall carbon nanotube (MWCNT) composites are investigated with Quantum Design SQUID magnetometer (MPMS XL). The surface of the composite films is studied via BRUKER Multimode 8 Atomic Force Microscope, as well. The polystyrene/MWCNT composites have been prepared by the group of professor Okotrub (Physics Chemistry of Nanomaterials laboratory, Nikolaev Institute of Inorganic Chemistry, Russia). The composite films have been prepared by solution processing and stretching method. The approximate length and inner diameter of the MWCNTs used in fabrication are 260 μm and 10 nm, respectively. The content of MWCNTs is 1 and 2.5 contents percent (wt%) for studied samples. The stretching of the samples is 30% for samples with 1 and 2.5 wt% content, and one sample with 1 wt% loading of MWCNTs is 100% stretched. MWCNTs aligned perpendicular to a silicon substrate are used as a reference sample. The magnetization field dependencies of the samples exhibit hysteresis behavior. The values of saturation magnetization of composite films are much less compared to that of the reference sample. The saturation magnetization coercitivity field value drops with decrease of MWCNT content. At high magnetic fields strong presence of diamagnetism is observed. Measurements in magnetic field parallel and perpendicular to the composite plate display anisotropy with respect to the direction of stretching. Temperature dependences of magnetization for all samples display difference between zero-field cooled and field-cooled curves of magnetization. This divergence confirms the presence of magnetic interactions in the material. The atomic force microscopy study of the composites’ surfaces revealed that they are relatively smooth and the nanotubes are aligned with the axis of stretching to some extent.