Dewatering of hard-to-dewater pulps

Nanocellulose has much potential for enhancing the tensile strength of paper but it slows down significantly drainage, restricting its use in industrial scale. Main objective of the work was to find ways to improve the dewatering of nanocellulose-containing papers. The effects of cationic potato starch, microparticle system and filler addition on dewatering and such key properties as formation, tensile strength and air permeance of manufactured paper were studied. Test points had 0, 4 or 8 % CNF and 0, 15 or 30 % PCC content. Based on earlier studies, 25 mg/g starch dosage was added to some test points. Modern microparticle system, consisted of cationic polyacrylamide and amorphous silica, was used in few test points. Dosages for both components were 0.3 and 0.6 mg/g, following the recommendations of the supplier. Also, the influences of CNF and filler on drying behaviour after different stages (drainage, wet pressing and cylinder drying) were estimated. Following trends were observed. Starch does not have unambiguous influence on dewatering. In some cases, it improved drainage slightly but effects on the properties of end product were discovered small. Filler quickened dewatering but large proportions were noticed to be detrimental for the drainage, air permeance and tensile strength. Microparticle system improved drainage notably, especially if CNF dosage was high. In addition, microparticle system increased tensile strength and decreased air permeance. However, its effects on formation were detrimental. Dewatering of nanocellulose-containing furnishes is treatable up to a certain point. In the end, such drainage times that were measured from test points which consisted only of pure kraft pulps are awkward to reach.

The Effects of Some Furnish and Paper Structure Related Factors on Wet Web Tensile and Relaxation Characteristics

The objective of this thesis was to identify the effects of different factors on the tension and tension relaxation of wet paper web after high-speed straining. The study was motivated by the plausible connection between wet web mechanical properties and wet web runnability on paper machines shown by previous studies. The mechanical properties of wet paper were examined using a fast tensile test rig with a strain rate of 1000%/s. Most of the tests were carried out with laboratory handsheets, but samples from a pilot paper machine were also used. The tension relaxation of paper was evaluated as the tension remaining after 0.475 s of relaxation (residual tension). The tensile and relaxation properties of wet webs were found to be strongly dependent on the quality and amount of fines. With low fines content, the tensile strength and residual tension of wet paper was mainly determined by the mechanical interactions between fibres at their contact points. As the fines strengthen the mechanical interaction in the network, the fibre properties also become important. Fibre deformations caused by the mechanical treatment of pulp were shown to reduce the mechanical properties of both dry and wet paper. However, the effect was significantly higher for wet paper. An increase of filler content from 10% to 25% greatly reduced the tensile strength of dry paper, but did not significantly impair wet web tensile strength or residual tension. Increased filler content in wet web was shown to increase the dryness of the wet web after the press section, which partly compensates for the reduction of fibrous material in the web. It is also presumable that fillers increase entanglement friction between fibres, which is beneficial for wet web strength. Different contaminants present in white water during sheet formation resulted in lowered surface tension and increased dryness after wet pressing. The addition of different contaminants reduced the tensile strength of the dry paper. The reduction of dry paper tensile strength could not be explained by the reduced surface tension, but rather on the tendency of different contaminants to interfere with the inter-fibre bonding. Additionally, wet web strength was not affected by the changes in the surface tension of white water or possible changes in the hydrophilicity of fibres caused by the addition of different contaminants. The spraying of different polymers on wet paper before wet pressing had a significant effect on both dry and wet web tensile strength, whereas wet web elastic modulus and residual tension were basically not affected. We suggest that the increase of dry and wet paper strength could be affected by the molecular level interactions between these chemicals and fibres. The most significant increases in dry and wet paper strength were achieved with a dual application of anionic and cationic polymers. Furthermore, selectively adding papermaking chemicals to different fibre fractions (as opposed to adding chemicals to the whole pulp) improved the wet web mechanical properties and the drainage of the pulp suspension.

Biochemical Modification of Thermomechanical Pulp Fibers

The first objective of this study was to find out reliable laboratory methods to predict the effect of enzymes on specific energy consumption and fiber properties of TMP pulp. The second one was to find with interactive software called “Knowledge discovery in databases” enzymes or other additives that can be used in finding a solution to reduce energy consumption of TMP pulp. The chemical composition of wood and enzymes, which have activity on main wood components were presented in the literature part of the work. The results of previous research in energy reduction of TMP process with enzymes were also highlighted. The main principles of knowledge discovery have been included in literature part too. The experimental part of the work contains the methods description in which the standard size chip, crushed chip and fiberized spruce chip (fiberized pulp) were used. Different types of enzymatic treatment with different dosages and time were tested during the experiments and showed. Pectinase, endoglucanase and mixture of enzymes were used for evaluation of method reliability. The fines content and fiber length of pulp was measured and used as evidence of enzymes' effect. The refining method with “Bauer” laboratory disc refiner was evaluated as not highly reliable. It was not able to provide high repeatability of results, because of uncontrolled feeding capacity and refining consistency. The refining method with Valley refiner did not have a lot of variables and showed stable and repeatable results in energy saving. The results of experiments showed that efficient enzymes impregnation is probably the main target with enzymes application for energy saving. During the work the fiberized pulp showed high accessibility to enzymatic treatment and liquid penetration without special impregnating equipment. The reason was that fiberized pulp has larger wood surface area and thereby the contact area between the enzymatic solution and wood is also larger. Standard size chip and crushed chip treatment without special impregnator of enzymatic solution was evaluated as not efficient and did not show visible, repeatable results in energy consumption decrease. Thereby it was concluded that using of fiberized pulp and Valley refiner for measurements of enzymes' effectiveness in SEC decrease is more suitable than normal size chip and crushed chip with “Bauer” refiner. Endoglucanase with 5 kg/t dosage showed about 20% energy consumption decrease. Mixture of enzymes with 1.5 kg/t dosage showed about 15% decrease of energy consumption during the refining. Pectinase at different dosages and treatment times did not show significant effect on energy consumption. Results of knowledge discovery in databases showed the xylanase, cellulase and pectinase blend as most promising for energy reduction in TMP process. Surfactants were determined as effective additives for energy saving with enzymes.

Effect of pulps fractionation on formation and strength properties of laboratory hand sheets

The objectives of the work were to study the effect of dewatering time varying on formation properties of papersheets, to determine the role of fines fraction in creation of paper with good formation and strength properties of papersheets, and also to study the effect of charge modification of fibers fractionations on formation properties of handsheets. The paper formation is one of the most important structural properties of paper. This property has effect on physical and optical characteristics of paper. In thi work the effect of formation on tensile strength was determined. The formation properties were analyzed by using the AMBERTEC Beta Formation Tester. The PAM addition as a f;locculant agent did some changes in the formation of paper. Paper sheets were also made from different furnishes of both birch and pine pulps. The fibers particles as a fines have great effect on drainability changes. Fines fraction played important role in papermaking. The two kinds of pulps (pine and birch pulps) were also used in this work for investigation of fines role. As it was expected the fines fraction gave positive effect on paper formation, but when fines fraction was added above initial fines content the formation of paper was deteriorated. The effect of paper formation on tensile strength was also determined. In many cases the poor formation of paper had negative effect on strength properties of paper..

Inledning til geographien öfver Swerige : upstäld af Eric Tuneld.

Digital reproduction, The National Library of Finland, Centre for Preservation and Digitisation, Mikkeli

Metsäsääntely Suomessa ja Venäjällä. Näkökulmia kestävään metsätalouteen

Sustainability is the aim of forest management and forest regulation in many countries. Accordingly, forest management has been steered towards more environmentally friendly methods and new regulatory instruments have been introduced. At the same time, wood trade and forest industry have become a global business. Even if the importance of national forest legislation has not decreased, it has been widely acknowledged that national regulation of forest management is no longer sufficient. The movement of goods does not acknowledge boundaries, even though most negative environmental and social consequences stay in the country of origin of wood and other raw materials. As a partial solution to this dilemma, different kinds of regulations have been developed. Various forest certification schemes and wood trade regulation in the EU (995/2010) are examples of efforts to prevent illegal logging and unsustainable forestry. The Finland-based forest industry is to a varying extent dependent on wood trade from Russia. Especially in the 1990‟s, ethical questions concerning import of wood from Russian old growth forests near the Finnish border were widely discussed. Consequently, forest industry enterprises have developed systems to trace the origin of wood and to buy certified wood from Russia. The aim of the research has been to evaluate Finnish and Russian forest regulations in order to investigate what kind of forest management these regulations enhance, and to what extent ecologically sustainable forest management has been integrated into different forms of regulation. I have examined Finnish and Russian forest regulation in four separate articles based on the topics of the Russian Forest Code, forest certification and other voluntary forest protection measures in Russia, Finnish forest certification and Finnish forest legislation. One objective has been to analyse the roles voluntary forest certification plays in promoting sustainable forest management in different countries. In my research, I have mainly concentrated on ecological sustainability and protection of biodiversity, although other aspects of sustainable forest management have been touched upon in different articles. In the following I shall conclude the findings of my research. When the current Russian Forest Code (2006) was being adopted, the main emphasis was not on ecological issues, but on reorganizing forest governance. The role of ecological requirements was even slightly diminished during the legislative reform. There are, nevertheless, still stipulations aiming at ecological sustainability, such as the division of forests into different forest management categories and various protection zones. In 2000, FSC forest certification arrived in Russia, at present covering already 28 million hectares of forests. The PEFC scheme is now in use as well, but to a much lesser extent. If properly implemented, Russian forest certification schemes clearly improve the level of ecological and social sustainability of forestry in Russia. Certification criteria, however, are partly in conflict with the Russian forest legislation and certified enterprises have been forced to pay fines or to negotiate with forest authorities. This clearly indicates that even if Russian forest legislation has otherwise been liberalized to a certain extent, some significant paternalism still exists. Voluntary, hands-on biodiversity protection measures are not valued, and they are not part of the official protection policies as in many other countries. However, there have been some regional solutions to this dilemma. In the Republic of Karelia forest authorities have approved a set of forest biodiversity protection rules created by a local NGO and a forest industry enterprise. By following these local rules, an enterprise can avoid fines for protection measures. The current Finnish Forest Act was adopted in 1996. It brought forest legislation into a new era as some ecological aspects were integrated into forest legislation. The various soft-law forest management recommendations further increased the level of biodiversity protection. My evaluation of the overall legitimacy of the Finnish forest legislation and forest management paradigm revealed, however, several problematic issues. As part of this study I analysed the history of the current forest management paradigm. This analysis revealed the path dependency which still hinders the protection of biodiversity and clearly decreases the general legitimacy of forest management. Due to several historical reasons only even-structured forest management based on clear cuts has for decades been officially approved in Finland. Due to increasing demands of forest owners the legislation is finally being revised. Yet, the official approval of uneven-structured forest management would not be enough to fully improve ecological, social and cultural legitimacy. The latest ecological theories and knowledge of endangered species should be taken into account in the on-going reform of forest legislation as well as the modernisation. Forest legislation is one of the very few spheres of Finnish environmental legislation where openness and participation are still considered a threat. The first Finnish forest certification scheme, PEFC, was established in 2000. It now covers more than 20 million hectares, about 95% of the forests in Finland. PEFC Finland does not require a higher level of biodiversity protection than the recommendations by Tapio (the Development Centre for Forestry), but certification has unified forest management practices and requires more protection measures than mere forest legislation. The study suggests that in Finland PEFC has not functioned as an instrument which would substantially improve the level of forest management. Rather it has supported the status quo of the forest sector. While the ecological and social responsibility of Finland-based forest corporations was one impetus for this research, I want to conclude that there are problems related to forest legislation and non-state regulation in both Finland and Russia. If an enterprise buying wood from Russia buys only certified wood, and carefully avoids wood coming from high conservation value forests that are either ecologically or socially valuable, it can be claimed to be as sustainably produced as in Finland. However, there must be continuous scrutiny of the circumstances. In Russia, the level of the compliance of certification criteria varies considerably, and there are vast unprotected invaluable forest areas. The utilisation of these areas should not be based on short-sighted decisions or lack of consensus among stakeholders.

Topochemistry of physical and chemical pretreatments of biomass as investigated by FE-SEM, XPS and ToF-SIMS

Surface chemistry is of great importance in plant biomass engineering and applications. The surface chemical composition of biomass which includes lignin, carbohydrates and extractives influences its interactions with chemical agents, such as pulp processing/papermaking chemicals, or enzymes for different purposes. In this thesis, the changes in the surface chemical composition of lignocellulosic biomass after physical modification for the improvement of resulting paper properties and chemical treatment for the enhancement of enzymatic hydrolysis were investigated. Low consistency (LC) refining was used as physical treatment of bleached softwood and hardwood pulp samples, and the surface chemistry of refined samples was investigated. The refined pulp was analysed as whole pulp while the fines-free fibre samples were characterized separately. The fines produced in LCrefining contributed to an enlarged surface specific area as well as the change of surface coverage by lignin and extractives, as investigated by X-ray photoelectron spectroscopy (XPS). The surface coverage by lignin of the whole pulp decreased after refining while the surface coverage by extractives increased both for pine and eucalyptus. In the case of pine, the removal of fines resulted in reduction of the surface coverage by extractives, while the surface coverage by lignin increased on fibre sample (without fines). In the case of eucalyptus, the surface coverage by lignin of fibre samples decreased after the removal of fines. In addition, the surface distribution of carbohydrates, lignin and extractives of pine and eucalyptus samples was determined by Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). LC-refining increased the amounts of pentose, hexose and extractives on the surface of pine samples. ToF-SIMS also gave clear evidence about xylan deposition and reduction of surface lignin distribution on the fibre of eucalyptus. However, the changes in the surface chemical composition during the physical treatment has led to an increase in the adsorption of fluorescent whitening agents (FWAs) on fibres due to a combination of electro-static forces, specific surface area of fibres and hydrophobic interactions. Various physicochemical pretreatments were conducted on wood and non-wood biomass for enhancing enzymatic hydrolysis of polysaccharides, and the surface chemistry of the pretreated and enzymatically hydrolysed samples was investigated by field emission scanning electron microscopy (FE-SEM), XPS and ToF-SIMS. A hydrotrope was used as a relatively novel pretreatment technology both in the case of wood and non-wood biomass. For comparison, ionic liquid and hydrothermal pretreatments were applied on softwood and hardwood as well. Thus, XPS analysis showed that the surface lignin was more efficiently removed by hydrotropic pretreatment compared to ionic liquid or hydrothermal pretreatments. SEM analysis also found that already at room temperature the ionic liquid pretreatments were more effective in swelling the fibres compared with hydrotropic pretreatment at elevated temperatures. The enzymatic hydrolysis yield of hardwood was enhanced due to the decrease in surface coverage of lignin, which was induced by hydrotropic treatment. However, hydrotropic pretreatment was not appropriate for softwood because of the predominance of guaiacyl lignin structure in this material. In addition, the reduction of surface lignin and xylan during pretreatment and subsequent increase in cellulose hydrolysis by enzyme could be observed from ToF-SIMS results. The characterisation of the non-wood biomass (e.g. sugarcane bagasse and common reed) treated by hydrotropic method, alkaline and alkaline hydrogen peroxide pretreatments were carried out by XPS and ToF-SIMS. According to the results, the action for the removal of the surface lignin of non-wood biomass by hydrotropic pretreatment was more significant compared to alkaline and alkaline hydrogen peroxide pretreatments, although a higher total amount of lignin could be removed by alkaline and alkaline hydrogen peroxide pretreatment. Furthermore, xylan could be remarkably more efficiently removed by hydrotropic method. Therefore, the glucan yield achieved from hydrotropic treated sample was higher than that from samples treated with alkaline or alkaline hydrogen peroxide. Through the use of ToF-SIMS, the distribution and localization of lignin and carbohydrates on the surface of ignocelluloses during pretreatment and enzymatic hydrolysis could be detected, and xylan degradation during enzymatic hydrolysis could also be assessed. Thus, based on the results from XPS and ToF-SIMS, the mechanism of the hydrotropic pretreatment in improving the accessibility of enzymes to fibre and further ameliorating of the enzymatic saccharification could be better elucidated.

Aasialaisen tuotantotavan korkein muoto

Kirjallisuusarvostelu