A novel procedure for establishing clinching parameters for high strength steel sheet

The building industry has a particular interest in using clinching as a joining method for frame constructions of light-frame housing. Normally many clinch joints are required in joining of frames.In order to maximise the strength of the complete assembly, each clinch joint must be as sound as possible. Experimental testing is the main means of optimising a particular clinch joint. This includes shear strength testing and visual observation of joint cross-sections. The manufacturers of clinching equipment normally perform such experimental trials. Finite element analysis can also be used to optimise the tool geometry and the process parameter, X, which represents the thickness of the base of the joint. However, such procedures require dedicated software, a skilled operator, and test specimens in order to verify the finite element model. In addition, when using current technology several hours' computing time may be necessary. The objective of the study was to develop a simple calculation procedure for rapidly establishing an optimum value for the parameter X for a given tool combination. It should be possible to use the procedure on a daily basis, without stringent demands on the skill of the operator or the equipment. It is also desirable that the procedure would significantly decrease thenumber of shear strength tests required for verification. The experimental workinvolved tests in order to obtain an understanding of the behaviour of the sheets during clinching. The most notable observation concerned the stage of the process in which the upper sheet was initially bent, after which the deformation mechanism changed to shearing and elongation. The amount of deformation was measured relative to the original location of the upper sheet, and characterised as the C-measure. By understanding in detail the behaviour of the upper sheet, it waspossible to estimate a bending line function for the surface of the upper sheet. A procedure was developed, which makes it possible to estimate the process parameter X for each tool combination with a fixed die. The procedure is based on equating the volume of material on the punch side with the volume of the die. Detailed information concerning the behaviour of material on the punch side is required, assuming that the volume of die does not change during the process. The procedure was applied to shear strength testing of a sample material. The sample material was continuously hot-dip zinc-coated high-strength constructional steel,with a nominal thickness of 1.0 mm. The minimum Rp0.2 proof stress was 637 N/mm2. Such material has not yet been used extensively in light-frame housing, and little has been published on clinching of the material. The performance of the material is therefore of particular interest. Companies that use clinching on a daily basis stand to gain the greatest benefit from the procedure. By understanding the behaviour of sheets in different cases, it is possible to use data at an early stage for adjusting and optimising the process. In particular, the functionality of common tools can be increased since it is possible to characterise the complete range of existing tools. The study increases and broadens the amount ofbasic information concerning the clinching process. New approaches and points of view are presented and used for generating new knowledge.

Analytical Study on the Influence of Geometrical Parameters on the Fatigue Strength of Welds with Undercuts

The purpose of this study is to analyze the influence of geometric parameters on the fatigue strength of the welded joint. The thesis includes the analytical study pertaining to variation of undercut and the weld toe radius. The theoretical part includes the concepts of fracture mechanics, different stages of the crack propagation and finally the results. The numerical results are obtained from FRANC2D/L. The results show that the fatigue strength of the welded structure depends on the parameters of the welds such as the weld toe radius, weld angle, height of the undercut and plate thickness. The results show that the fatigue life can be improved by having the undercut as minimum as possible. However there has been significant variation on the fatigue life of the structure when the weld toe radius is increased.

The Optimization of Flotation Process Parameters in the Deinking Plant

Tämän diplomityön tavoitteena oli sekundäärisen esiflotaation optimointi Stora Enso Sachsen GmbH:n tehtaalla. Optimoinnin muuttujana käytettiin vaahdon määrää ja optimointiparametreinä ISO-vaaleutta, saantoja sekä tuhkapitoisuutta. Lisäksi tutkittiin flotaatiosakeuden vaikutusta myös muihin tehtaan flotaatioprosesseihin. Kirjallisuusosassa tarkasteltiin flotaatiotapahtumaa, poistettavien partikkeleiden ja ilmakuplien kontaktia, vaahdon muodostumista sekä tärkeimpiä käytössä olevia siistausflotaattoreiden laiteratkaisuja. Kokeellisessa osassa tutkittiin flotaatiosakeuden pienetämisen vaikutuksia tehtaan flotaatioprosesseihin tuhkapitoisuuden, ISO-vaaleuden, valon sironta- ja valon absorpiokerrointen kannalta. Sekundäärisen esiflotaation optimonti suoritettiin muuttamalla vaahdon määrää kolmella erilaisella injektorin koolla, (8 mm, 10 mm ja 13 mm), joista keskimmäinen kasvattaa 30 % massan tilavuusvirtaa ilmapitoisuuden muodossa. Optimonnin tarkoituksena oli kasvattaa hyväksytyn massajakeen ISO-vaaleutta, sekä kasvattaa kuitu- ja kokonaissaantoa sekundäärisessä esiflotaatiossa. Flotaatiosakeuden pienentämisellä oli edullisia vaikutuksia ISO-vaaleuteen ja valon sirontakertoimeen kussakin flotaatiossa. Tuhkapitoisuus pieneni sekundäärisissä flotaatioissa enemmän sakeuden ollessa pienempi, kun taas primäärisissä flotaatiossa vaikutus oli päinvastainen. Valon absorptiokerroin parani jälkiflotaatioissa alhaisemmalla sakeudella, kun taas esiflotaatioissa vaikutus oli päinvastainen. Sekundäärisen esiflotaation optimoinnin tuloksena oli lähes 5 % parempi ISO-vaaleus hyväksytyssä massajakeessa. Kokonaissaanto parani optimoinnin myötä 5 % ja kuitusaanto 2 %. Saantojen nousu tuottaa vuosittaisia säästöjä siistauslaitoksen tuotantokapasiteetin noustessa 0,5 %. Tämän lisäksi sekundäärisessä esiflotaatiossa rejektoituvan massavirran pienentyminen tuottaa lisäsäästöjä tehtaan voimalaitoksella.

Pellettien laatu ja ominaisuudet eri raaka-aineilla ja niiden seoksilla

Diplomityö tehtiin osana Vapon toteuttamaa monivuotista pelletin kehitysohjelmaa. Kehitysohjelma koostuu useista pienemmistä osaprojekteista, jotka täydentävät toinen toisiaan. Pellettien raaka-ainepohjan laajentaminen on eräs näistä osaprojekteista. Tutkimustyön tavoitteena oli selvittää erilaisten potentiaalisten bioraaka-aineiden soveltuvuutta pelletointiin joko sellaisenaan tai erilaisina seoksina. Raaka-aineiden pelletoitavuutta tutkittiin kenttäolosuhteissa mobiilipelletointilaitoksella. Laitoksen pääkomponentit muodostivat Kahl C 38–780 tasomatriisipuristin, jäähdytin ja täryseula. Pelletointikokeissa tutkittuja raaka-aineita olivat mäntysahanpuru, männynkuori, harvennusranka, haapa, koivu, jyrsinturve ja ruokohelpi. Raaka-aineiden irtotiheys käyttökosteudessa vaihteli välillä 73–244 kg/m3 ja keskimääräinen kosteuspitoisuus 6,5–15 %. Useissa tapauksissa säkitettyjä raaka-aineita säkkikostutettiin haluttuun kosteuspitoisuuteen ennen pelletointia. Säkkikostutettujen raaka-aineiden kosteuspitoisuudet vaihtelivat tällöin välillä 12–14 m- %. Valtaosa tutkituista raaka-aineista ja niiden seoksista pystyttiin pelletoimaan puristimen matriisilla 8/40 mm, jossa puristuskanavan halkaisija oli 8 mm ja kanavan suoran osan pituus 40 mm. Vaikeuksia tuotti ainoastaan pelkän koivupurun ja ruokohelven pelletointi. Käytetty matriisi oli kanavapituudeltaan liian pitkä koivupurun pelletointiin nostaen puristusvastuksen suureksi. Ruokohelven pelletoinnin vaikeudet johtuivat pääasiassa pelletointiin liian karkeasta raaka-aineesta. Myös matriisia 8/55 mm kokeiltiin, mutta se osoittautui liian ”tiukaksi” valtaosalle puuraaka-aineista. Ainoastaan jyrsinturpeen pelletointi onnistui tällä matriisilla. Männynkuoren pelletointia ei matriisilla 8/55 mm yritetty. Kenttäkokeissa valmistetuista pelleteistä määritettiin erilaisia ominaisuuksia, kuten keskipituus, kosteuspitoisuus, irtotiheys, hienoaineksen määrä ja käsittelykestävyys. Lujuus mitattiin sekä Ligno-testillä että CEN-rummutuslujuuden määrityksellä. Lisäksi pelleteille määritettiin alkuaineanalyysi, tuhkapitoisuus ja lämpöarvo ENAS Oy:n laboratoriossa Jyväskylässä. Ligno-testauksessa parhaimman luokan pelletin tulee yltää arvoon 97,5 %. Pelletoitaessa raaka-aineita ja niiden seoksia tasomatriisikoneella sopivalla matriisilla yllettiin usein näihin tai parempiin tuloksiin. Puumateriaaleilla raaka-aineen optimaalinen lähtökosteus oli välillä 12–14 m- % ja turpeella sekä ruokohelvellä 14–16 m- %. Pelletointi onnistui tällöin vaivattomasti, kunhan sopivat puristimen ajoparametrit oli löydetty. Pellettiä alkoi muodostua matriisin puristuskanavien lämpötilan kohotessa noin 70 ºC. Pellettien lämpötila stabiilitilanteessa heti pelletoinnin jälkeen oli useissa tapauksissa 80–90 ºC. Pelletoinnin aikainen tehontarve vaihteli välillä 90–150 kWh/t, ollen suurimmillaan irtotiheydeltään keveillä materiaaleilla. Raaka-aineen suuri partikkelikoko kasvatti puristimen tehontarvetta. Tämä havaittiin selvästi lisättäessä karkeaa ruokohelpisilppua eri raaka-aineiden joukkoon. Kestävyydeltään erinomaisia pellettejä saatiin, kun raaka-aineena oli jyrsinturve, harvennusranka tai mäntypuru. Varsinkin jyrsinturpeen ja harvennusrangan seoksesta valmistetut pelletit osoittautuivat erittäin kestäviksi. Myös jyrsinturpeen ja ruokohelven sekä mäntypurun ja ruokohelven seoksien pelleteille määritettiin hyviä kestävyysarvoja. Männynkuoresta valmistetut pelletit jäivät Ligno-testauksessa kestävyydeltään alle 97,5 % rajan. Pääsyynä tähän oli kuoren pelletointiin käytetyn matriisin 8/40 mm liian lyhyet puristuskanavat.

Flash Memory Cells Reliability Parameters Investigation

The present work is a part of the large project with purpose to qualify the Flash memory for automotive application using a standardized test and measurement flow. High memory reliability and data retention are the most critical parameters in this application. The current work covers the functional tests and data retention test. The purpose of the data retention test is to obtain the data retention parameters of the designed memory, i.e. the maximum time of information storage at specified conditions without critical charge leakage. For this purpose the charge leakage from the cells, which results in decrease of cells threshold voltage, was measured after a long-time hightemperature treatment at several temperatures. The amount of lost charge for each temperature was used to calculate the Arrhenius constant and activation energy for the discharge process. With this data, the discharge of the cells at different temperatures during long time can be predicted and the probability of data loss after years can be calculated. The memory chips, investigated in this work, were 0.035 μm CMOS Flash memory testchips, designed for further use in the Systems-on-Chips for automotive electronics.

Energy efficiency parameters in variable speed drives

The main purpose of this thesis is to measure and evaluate how accurately the current energy saving calculation in ABB’s new variable speed drive ACS850 works. The main topic of this thesis is energy-efficiency parameters. At the beginning of this thesis centrifugal pump, squirrel cage motor and variable speed drive, including some equations related to them, are being introduced. Also methods of throttling control and variable speed drive control of centrifugal pumps are being introduced. These subjects are introduced because the energy saving calculation in ACS850 is related to the centrifugal pumps usually driven by squirrel cage motors. The theory also includes short section about specific energy of pumping. Before measurements the current energy saving calculation of ACS850 is being introduced and analyzed. The measurements part includes introduction of measuring equipment, measurement results, summary and analysis of the measurements. At the end of this thesis a proposal for an improvement to the current energy saving calculation is being introduced and few proposals are made for new energy-efficiency parameters, which could be added to variable speed drives. At the end are also thoughts

On the effects of welding parameters on weld quality of plasma arc keyhole welding of structural steels

The possibility and the usefulness of applying plasma keyhole welding to structural steels with different compositions and material thicknesses, and in various welding positions has been examinated. Single pass butt welding with I groove in flat, horizontal vertical and vertical positions and root welding with V , Y and U grooves of thick plate material in flat position have been studied and the welds with high quality has been obtained. The technological conditions for successful welding are presented. The single and interactive effects of welding parameters on weld quality, especially on surface weld defects, geometrical form errors, internal defects and mechanical properties (strength, ductility, impact toughness, hardness and bendability) of weld joint, are presented. Welding parameter combinations providing the best quality welds are also presented.

The effects of real time control of welding parameters on weld quality in plasma arc keyhole welding

Joints intended for welding frequently show variations in geometry and position, for which it is unfortunately not possible to apply a single set of operating parameters to ensure constant quality. The cause of this difficulty lies in a number of factors, including inaccurate joint preparation and joint fit up, tack welds, as well as thermal distortion of the workpiece. In plasma arc keyhole welding of butt joints, deviations in the gap width may cause weld defects such as an incomplete weld bead, excessive penetration and burn through. Manual adjustment of welding parameters to compensate for variations in the gap width is very difficult, and unsatisfactory weld quality is often obtained. In this study a control system for plasma arc keyhole welding has been developed and used to study the effects of the real time control of welding parameters on gap tolerance during welding of austenitic stainless steel AISI 304L. The welding tests demonstrated the beneficial effect of real time control on weld quality. Compared with welding using constant parameters, the maximum tolerable gap width with an acceptable weld quality was 47% higher when using the real time controlled parameters for a plate thickness of 5 mm. In addition, burn through occurred with significantly larger gap widths when parameters were controlled in real time. Increased gap tolerance enables joints to be prepared and fit up less accurately, saving time and preparation costs for welding. In addition to the control system, a novel technique for back face monitoring is described in this study. The test results showed that the technique could be successfully applied for penetration monitoring when welding non magnetic materials. The results also imply that it is possible to measure the dimensions of the plasma efflux or weld root, and use this information in a feedback control system and, thus, maintain the required weld quality.

Field Weakening, Parameters and Operation Range of the Permanent Magnet Traction Motors

The main focus of this thesis is to define the field weakening point of permanent magnet synchronous machine with embedded magnets in traction applications. Along with the thesis a modelling program is made to help the designer to define the field weakening point in practical applications. The thesis utilizes the equations based on the current angle. These equations can be derived from the vector diagram of permanent magnet synchronous machine. The design parameters of the machine are: The maximum rotational speed, saliency ratio, maximum induced voltage and characteristic current. The main result of the thesis is finding out the rated rotational speed, from which the field weakening starts. The action of the machine is estimated at a wide speed range and the changes of machine parameters are examined.

Optimization of parameters for fiber laser-MAG hybrid welding in shipbuilding applications

The Arctic region becoming very active area of the industrial developments since it may contain approximately 15-25% of the hydrocarbon and other valuable natural resources which are in great demand nowadays. Harsh operation conditions make the Arctic region difficult to access due to low temperatures which can drop below -50 °C in winter and various additional loads. As a result, newer and modified metallic materials are implemented which can cause certain problems in welding them properly. Steel is still the most widely used material in the Arctic regions due to high mechanical properties, cheapness and manufacturability. Moreover, with recent steel manufacturing development it is possible to make up to 1100 MPa yield strength microalloyed high strength steel which can be operated at temperatures -60 °C possessing reasonable weldability, ductility and suitable impact toughness which is the most crucial property for the Arctic usability. For many years, the arc welding was the most dominant joining method of the metallic materials. Recently, other joining methods are successfully implemented into welding manufacturing due to growing industrial demands and one of them is the laser-arc hybrid welding. The laser-arc hybrid welding successfully combines the advantages and eliminates the disadvantages of the both joining methods therefore produce less distortions, reduce the need of edge preparation, generates narrower heat-affected zone, and increase welding speed or productivity significantly. Moreover, due to easy implementation of the filler wire, accordingly the mechanical properties of the joints can be manipulated in order to produce suitable quality. Moreover, with laser-arc hybrid welding it is possible to achieve matching weld metal compared to the base material even with the low alloying welding wires without excessive softening of the HAZ in the high strength steels. As a result, the laser-arc welding methods can be the most desired and dominating welding technology nowadays, and which is already operating in automotive and shipbuilding industries with a great success. However, in the future it can be extended to offshore, pipe-laying, and heavy equipment industries for arctic environment. CO2 and Nd:YAG laser sources in combination with gas metal arc source have been used widely in the past two decades. Recently, the fiber laser sources offered high power outputs with excellent beam quality, very high electrical efficiency, low maintenance expenses, and higher mobility due to fiber optics. As a result, fiber laser-arc hybrid process offers even more extended advantages and applications. However, the information about fiber or disk laser-arc hybrid welding is very limited. The objectives of the Master’s thesis are concentrated on the study of fiber laser-MAG hybrid welding parameters in order to understand resulting mechanical properties and quality of the welds. In this work only ferrous materials are reviewed. The qualitative methodological approach has been used to achieve the objectives. This study demonstrates that laser-arc hybrid welding is suitable for welding of many types, thicknesses and strength of steels with acceptable mechanical properties along very high productivity. New developments of the fiber laser-arc hybrid process offers extended capabilities over CO2 laser combined with the arc. This work can be used as guideline in hybrid welding technology with comprehensive study the effect of welding parameter on joint quality.

The estimation of tuberculosis transmission parameters using ABC and MCMC methods

The aim of this work is to apply approximate Bayesian computation in combination with Marcov chain Monte Carlo methods in order to estimate the parameters of tuberculosis transmission. The methods are applied to San Francisco data and the results are compared with the outcomes of previous works. Moreover, a methodological idea with the aim to reduce computational time is also described. Despite the fact that this approach is proved to work in an appropriate way, further analysis is needed to understand and test its behaviour in different cases. Some related suggestions to its further enhancement are described in the corresponding chapter.