Dynamic Model of a Small Once-Through Boiler

In this study, a model for the unsteady dynamic behaviour of a once-through counter flow boiler that uses an organic working fluid is presented. The boiler is a compact waste-heat boiler without a furnace and it has a preheater, a vaporiser and a superheater. The relative lengths of the boiler parts vary with the operating conditions since they are all parts of a single tube. The present research is a part of a study on the unsteady dynamics of an organic Rankine cycle power plant and it will be a part of a dynamic process model. The boiler model is presented using a selected example case that uses toluene as the process fluid and flue gas from natural gas combustion as the heat source. The dynamic behaviour of the boiler means transition from the steady initial state towards another steady state that corresponds to the changed process conditions. The solution method chosen was to find such a pressure of the process fluid that the mass of the process fluid in the boiler equals the mass calculated using the mass flows into and out of the boiler during a time step, using the finite difference method. A special method of fast calculation of the thermal properties has been used, because most of the calculation time is spent in calculating the fluid properties. The boiler was divided into elements. The values of the thermodynamic properties and mass flows were calculated in the nodes that connect the elements. Dynamic behaviour was limited to the process fluid and tube wall, and the heat source was regarded as to be steady. The elements that connect the preheater to thevaporiser and the vaporiser to the superheater were treated in a special way that takes into account a flexible change from one part to the other. The model consists of the calculation of the steady state initial distribution of the variables in the nodes, and the calculation of these nodal values in a dynamic state. The initial state of the boiler was received from a steady process model that isnot a part of the boiler model. The known boundary values that may vary during the dynamic calculation were the inlet temperature and mass flow rates of both the heat source and the process fluid. A brief examination of the oscillation around a steady state, the so-called Ledinegg instability, was done. This examination showed that the pressure drop in the boiler is a third degree polynomial of the mass flow rate, and the stability criterion is a second degree polynomial of the enthalpy change in the preheater. The numerical examination showed that oscillations did not exist in the example case. The dynamic boiler model was analysed for linear and step changes of the entering fluid temperatures and flow rates.The problem for verifying the correctness of the achieved results was that there was no possibility o compare them with measurements. This is why the only way was to determine whether the obtained results were intuitively reasonable and the results changed logically when the boundary conditions were changed. The numerical stability was checked in a test run in which there was no change in input values. The differences compared with the initial values were so small that the effects of numerical oscillations were negligible. The heat source side tests showed that the model gives results that are logical in the directions of the changes, and the order of magnitude of the timescale of changes is also as expected. The results of the tests on the process fluid side showed that the model gives reasonable results both on the temperature changes that cause small alterations in the process state and on mass flow rate changes causing very great alterations. The test runs showed that the dynamic model has no problems in calculating cases in which temperature of the entering heat source suddenly goes below that of the tube wall or the process fluid.

Dynamic Capabilities and Firm Performance

Firms operating in a changing environment have a need for structures and practices that provide flexibility and enable rapid response to changes. Given the challenges they face in attempts to keep up with market needs, they have to continuously improve their processes and products, and develop new products to match market requirements. Success in changing markets depends on the firm's ability to convert knowledge into innovations, and consequently their internal structures and capabilities have an important role in innovation activities. According 10 the dynamic capability view of the firm, firms thus need dynamic capabilities in (he form ofassets, processes and structures that enable strategic flexibility and support entrepreneurial opportunity sensing and exploitation. Dynamic capabilities are also needed in conditions of rapid change in the operating environment, and in activities such as new product development and expansion to new markets. Despite the growing interest in these issues and the theoretical developments in the field of strategy research, there are still only very few empirical studies, and large-scale empirical studies in particular, that provide evidence that firms'dynamic capabilities are reflected in performance differences. This thesis represents an attempt to advance the research by providing empirical evidence of thelinkages between the firm's dynamic capabilities and performance in intenationalization and innovation activities. The aim is thus to increase knowledge and enhance understanding of the organizational factors that explain interfirm performance differences. The study is in two parts. The first part is the introduction and the second part comprises five research publications covering the theoretical foundations of the dynamic capability view and subsequent empirical analyses. Quantitative research methodology is used throughout. The thesis contributes to the literature in several ways. While a lot of prior research on dynamic capabilities is conceptual in nature, or conducted through case studies, this thesis introduces empirical measures for assessing the different aspects, and uses large-scale sampling to investigate the relationships between them and performance indicators. The dynamic capability view is further developed by integrating theoretical frameworks and research traditions from several disciplines. The results of the study provide support for the basic tenets of the dynamic capability view. The empirical findings demonstrate that the firm's ability to renew its knowledge base and other intangible assets, its proactive, entrepreneurial behavior, and the structures and practices that support operational flexibility arepositively related to performance indicators.

The effects of potentiallydisruptive technology on business model - a case study of new technologies in ICT industry

This study examines how firms interpret new, potentially disruptive technologies in their own strategic context. The work presents a cross-case analysis of four potentially disruptive technologies or technical operating models: Bluetooth, WLAN, Grid computing and Mobile Peer-to-peer paradigm. The technologies were investigated from the perspective of three mobile operators, a device manufacturer and a software company in the ICT industry. The theoretical background for the study consists of the resource-based view of the firm with dynamic perspective, the theories on the nature of technology and innovations, and the concept of business model. The literature review builds up a propositional framework for estimating the amount of radical change in the companies' business model with two middle variables, the disruptiveness potential of a new technology, and the strategic importance of a new technology to a firm. The data was gathered in group discussion sessions in each company. The results of each case analysis were brought together to evaluate, how firms interpret the potential disruptiveness in terms of changes in product characteristics and added value, technology and market uncertainty, changes in product-market positions, possible competence disruption and changes in value network positions. The results indicate that the perceived disruptiveness in terms ofproduct characteristics does not necessarily translate into strategic importance. In addition, firms did not see the new technologies as a threat in terms of potential competence disruption.

Modeling dynamic behavior in tilting pad gas journal bearings

Thisresearch deals with the dynamic modeling of gas lubricated tilting pad journal bearings provided with spring supported pads, including experimental verification of the computation. On the basis of a mathematical model of a film bearing, a computer program has been developed, which can be used for the simulation of a special type of tilting pad gas journal bearing supported by a rotary spring under different loading conditions time dependently (transient running conditions due to geometry variations in time externally imposed). On the basis of literature, different transformations have been used in the model to achieve simpler calculation. The numerical simulation is used to solve a non-stationary case of a gasfilm. The simulation results were compared with literature results in a stationary case (steady running conditions) and they were found to be equal. In addition to this, comparisons were made with a number of stationary and non-stationary bearing tests, which were performed at Lappeenranta University of Technology using bearings designed with the simulation program. A study was also made using numerical simulation and literature to establish the influence of the different bearing parameters on the stability of the bearing. Comparison work was done with literature on tilting pad gas bearings. This bearing type is rarely used. One literature reference has studied the same bearing type as that used in LUT. A new design of tilting pad gas bearing is introduced. It is based on a stainless steel body and electron beam welding of the bearing parts. It has good operation characteristics and is easier to tune and faster to manufacture than traditional constructions. It is also suitable for large serial production.

Dynamic application development in Symbian OS

Diplomityössä tutkitaan, kuinka Symbian-sovelluskehitystä voitaisiin tehostaa. Työssä esitellään Symbian-käyttöjärjestelmä, sekä pohditaan haasteita ja rajoitteita joita Symbian sovelluskehityksessä kohdataan. Myöskin jo olemassa olevia kehitystapoja pohditaan työn tavoitteen kannalta. Symbian-sovelluskehityksessä tehdään toistuvasti samoja asioita. Koska Symbian on avoin käyttöjärjestelmä, sovelluskehittäjiä on paljon. Tehokkaamman kehitystavan löytäminen säästäisi paljon resursseja. Tällä hetkellä perinteiset ohjelmointitavat näyttävät olevan suosituin tapa kehittää sovelluksia. Kuitenkin on jo olemassa useita ratkaisuja, jotka pyrkivät tehostamaan sovelluskehitystä, mikä todistaa tarpeen kehittää tehokkuutta. Työssä toteutettu systeemi ajaa Symbian sovelluksia XML-määrityksen pohjalta. Kun käytetään XML-määritystä C++-koodin sijasta, sovelluskehitys muuttuu. Näiden muutosten täytyy kuitenkin olla myönteisiä, eivätkä ne saa haitata ohjelmiston laatua tai käytettävyyttä.

Dynamic Capabilities and Real Options

Tutkielman tavoitteena oli selvittää dynaamisten kyvykkyyksien teorian kehittymistä ja nykytilaa. Työssä tarkastellaan myös mahdollisuuksia yhdistää reaalioptioajattelua ja dynaamisten kyvykkyyksien teoriaa. Tutkielma on toteutettu teoreettisena kirjallisuuskatsauksena. Dynaamisten kyvykkyyksien teorian mukaan muuttuvassa toimintaympäristössä yritysten kilpailuetu perustuu kykyyn rakentaa, yhdistää ja muokata resursseja ja kyvykkyyksiä. Yritysten täytyy pystyä löytämään, sulauttamaan ja muuntamaan tietoa voidakseen tunnistaa uusia mahdollisuuksia ja pystyäkseen reagoimaan niihin. Tutkielma tuo esille uusia yhteyksiä dynaamisten kyvykkyyksien teorian ja yritysten käyttäytymisen välillä. Reaalioptioajattelu auttaa tunnistamaan yrityksen rajojen määrittämiseen vaikuttavia tekijöitä. Työssä tehdään ehdotuksia dynaamisten kyvykkyyksien teorian jatkotutkimusta varten.

The Dynamic Customer Portfolio Method in Customer Relationship Management

Tutkielman tavoitteena on määritellä keskeiset ja sopivat asiakasportfoliomallit ja asiakasmatriisit asiakassuhteen määrittämiseen. Tutkimus keskittyy asiakassuhteen arvottamiseen ja avainasiakkaiden määrittämiseen kohdeyrityksessä. Keskeisimmät ja sopivimmat asiakasportfliomallit huomioidaan asiakkaiden arvioinnissa. Tutkielman teoriaosassa esitellään tunnetuimmat ja käytetyimmät asiakasportfoliomallit ja matriisit alan kirjallisuuden perusteella. Tämän lisäksi asiakasportfoliomalleihin yhdistetään näkökulmia suhdemarkkinoinnin, asiakkuuksien johtamisen ja tuoteportfolioiden teorioista. Keskeisimmät kirjallisuuden lähteet ovat johtamisen ja markkinoinnin alalta. Tutkielman empiriaosassa esitellään kohdeyritys ja sen tämän hetkinen asiakassuhteiden johtamiskäytäntö. Lisäksi tehdään parannusehdotuksia kohdeyrityksen nykyiseen asiakassuhteiden arvottamismenetelmään jotta asiakassuhteiden arvon laskeminen vastaisi mahdollisimman hyvin kohdeyrityksen nykyisiä tarpeita. Asiakassuhteen arvon määrittämiseksi käytetään myös fokusryhmähaastattelua. Avainasiakkaat määritellään ja tilannetta havainnollistetaan sijoittamalla avainasiakkaat asiakasportfolioon.

On the Analysis and Control of a Linear Synchronous Servomotor with a Flexible Load

Industry's growing need for higher productivity is placing new demands on mechanisms connected with electrical motors, because these can easily lead to vibration problems due to fast dynamics. Furthermore, the nonlinear effects caused by a motor frequently reduce servo stability, which diminishes the controller's ability to predict and maintain speed. Hence, the flexibility of a mechanism and its control has become an important area of research. The basic approach in control system engineering is to assume that the mechanism connected to a motor is rigid, so that vibrations in the tool mechanism, reel, gripper or any apparatus connected to the motor are not taken into account. This might reduce the ability of the machine system to carry out its assignment and shorten the lifetime of the equipment. Nonetheless, it is usually more important to know how the mechanism, or in other words the load on the motor, behaves. A nonlinear load control method for a permanent magnet linear synchronous motor is developed and implemented in the thesis. The purpose of the controller is to track a flexible load to the desired velocity reference as fast as possible and without awkward oscillations. The control method is based on an adaptive backstepping algorithm with its stability ensured by the Lyapunov stability theorem. As a reference controller for the backstepping method, a hybrid neural controller is introduced in which the linear motor itself is controlled by a conventional PI velocity controller and the vibration of the associated flexible mechanism is suppressed from an outer control loop using a compensation signal from a multilayer perceptron network. To avoid the local minimum problem entailed in neural networks, the initial weights are searched for offline by means of a differential evolution algorithm. The states of a mechanical system for controllers are estimated using the Kalman filter. The theoretical results obtained from the control design are validated with the lumped mass model for a mechanism. Generalization of the mechanism allows the methods derived here to be widely implemented in machine automation. The control algorithms are first designed in a specially introduced nonlinear simulation model and then implemented in the physical linear motor using a DSP (Digital Signal Processor) application. The measurements prove that both controllers are capable of suppressing vibration, but that the backstepping method is superior to others due to its accuracy of response and stability properties.

Partnering in the Dynamic Environment: The Role of Trust in Asymmetric Technology Partnership Formation

The purpose of this study was to increase the understanding of the role and nature of trust in asymmetric technology partnership formation. In the knowledge-based "learning race" knowledge is considered as a primary source for competitive advantage. In the emerging ICT sector the high pace of technological change, the convergence of technologies and industries as well as the increasing complexity and uncertainty have forced even the largest players to seek cooperation for complementary knowledge and capabilities. Small technology firms need the complementary resources and legitimacy of the large firms to grow and compete in the global market place. Most of the earlier research indicates, however, that partnerships with asymmetric size, managerial resources and cultures have failed. A basic assumption supported by earlier research was that trust is a critical factor in asymmetric technology partnership formation. Asymmetric technology partnership formation is a dynamic and multi-dimensional process, and consequently a holistic research approach was selected. Research issue was approached from different levels: the individual decision-maker, the firm and the relationship between the parties. Also the impact of the dynamic environment and technology content was analyzed. A multitheoretical approach and a qualitative research method with in-depth interviews in five large ICT companies and eight small ICT companies enabled a holistic and rich view of the research issue. Study contributes on the scarce understanding on the nature and evolution of trust in asymmetric technology partnership formation. It sheds also light on the specific nature of asymmetric technology partnerships. The partnerships were found to be tentative and the diverse strategic intent of small and large technology firms appeared as a major challenge. The role of the boundary spanner was highlighted as a possibility to match the incompatible organizational cultures. A shared vision was found to be a pre-condition for individual-based fast trust leading to intuitive decision-making and experimentation. The relationships were tentative and they were continuously re-evaluated through the key actors' sense making of the technology content, asymmetry and the dynamic environment. A multi-dimensional conceptualization for trust was created and propositions on the role and nature of trust for further research are given. The purpose of this study was to increase the understanding of the role and nature of trust in asymmetric technology partnership formation. In the knowledge-based "learning race" knowledge is considered as a primary source for competitive advantage. In the emerging ICT sector the high pace of technological change, the convergence of technologies and industries as well as the increasing complexity and uncertainty have forced even the largest players to seek cooperation for complementary knowledge and capabilities. Small technology firms need the complementary resources and legitimacy of the large firms to grow and compete in the global market place. Most of the earlier research indicates, however, that partnerships with asymmetric size, managerial resources and cultures have failed. A basic assumption supported by earlier research was that trust is a critical factor in asymmetric technology partnership formation. Asymmetric technology partnership formation is a dynamic and multi-dimensional process, and consequently a holistic research approach was selected. Research issue was approached from different levels: the individual decision-maker, the firm and the relationship between the parties. Also the impact of the dynamic environment and technology content was analyzed. A multitheoretical approach and a qualitative research method with in-depth interviews in five large ICT companies and eight small ICT companies enabled a holistic and rich view of the research issue. Study contributes on the scarce understanding on the nature and evolution of trust in asymmetric technology partnership formation. It sheds also light on the specific nature of asymmetric technology partnerships. The partnerships were found to be tentative and the diverse strategic intent of small and large technology firms appeared as a major challenge. The role of the boundary spanner was highlighted as a possibility to match the incompatible organizational cultures. A shared vision was found to be a pre-condition for individual-based fast trust leading to intuitive decision-making and experimentation. The relationships were tentative and they were continuously re-evaluated through the key actors' sense making of the technology content, asymmetry and the dynamic environment. A multi-dimensional conceptualization for trust was created and propositions on the role and nature of trust for further research are given.

Flexible Multibody Simulation Approach in the Dynamic Analysis of Bone Strains Activity

The objective of this study is to show that bone strains due to dynamic mechanical loading during physical activity can be analysed using the flexible multibody simulation approach. Strains within the bone tissue play a major role in bone (re)modeling. Based on previous studies, it has been shown that dynamic loading seems to be more important for bone (re)modeling than static loading. The finite element method has been used previously to assess bone strains. However, the finite element method may be limited to static analysis of bone strains due to the expensive computation required for dynamic analysis, especially for a biomechanical system consisting of several bodies. Further, in vivo implementation of strain gauges on the surfaces of bone has been used previously in order to quantify the mechanical loading environment of the skeleton. However, in vivo strain measurement requires invasive methodology, which is challenging and limited to certain regions of superficial bones only, such as the anterior surface of the tibia. In this study, an alternative numerical approach to analyzing in vivo strains, based on the flexible multibody simulation approach, is proposed. In order to investigate the reliability of the proposed approach, three 3-dimensional musculoskeletal models where the right tibia is assumed to be flexible, are used as demonstration examples. The models are employed in a forward dynamics simulation in order to predict the tibial strains during walking on a level exercise. The flexible tibial model is developed using the actual geometry of the subject’s tibia, which is obtained from 3 dimensional reconstruction of Magnetic Resonance Images. Inverse dynamics simulation based on motion capture data obtained from walking at a constant velocity is used to calculate the desired contraction trajectory for each muscle. In the forward dynamics simulation, a proportional derivative servo controller is used to calculate each muscle force required to reproduce the motion, based on the desired muscle contraction trajectory obtained from the inverse dynamics simulation. Experimental measurements are used to verify the models and check the accuracy of the models in replicating the realistic mechanical loading environment measured from the walking test. The predicted strain results by the models show consistency with literature-based in vivo strain measurements. In conclusion, the non-invasive flexible multibody simulation approach may be used as a surrogate for experimental bone strain measurement, and thus be of use in detailed strain estimation of bones in different applications. Consequently, the information obtained from the present approach might be useful in clinical applications, including optimizing implant design and devising exercises to prevent bone fragility, accelerate fracture healing and reduce osteoporotic bone loss.

Threat Simulation- The Function of Dreaming?

Dreaming is a pure form of phenomenality, created by the brain untouched by external stimulation or behavioral activity, yet including a full range of phenomenal contents. Thus, it has been suggested that the dreaming brain could be used as a model system in a biological research program on consciousness (Revonsuo, 2006). In the present thesis, the philosophical view of biological realism is accepted, and thus, dreaming is considered as a natural biological phenomenon, explainable in naturalistic terms. The major theoretical contribution of the present thesis is that it explores dreaming from a multidisciplinary perspective, integrating information from various fields of science, such as dream research, consciousness research, evolutionary psychology, and cognitive neuroscience. Further, it places dreaming into a multilevel framework, and investigates the constitutive, etiological, and contextual explanations for dreaming. Currently, the only theory offering a full multilevel explanation for dreaming, that is, a theory including constitutive, etiological, and contextual level explanations, is the Threat Simulation Theory (TST) (Revonsuo, 2000a; 2000b). The empirical significance of the present thesis lies in the tests conducted to test this specific theory put forth to explain the form, content, and biological function of dreaming. The first step in the empirical testing of the TST was to define exact criteria for what is a ‘threatening event’ in dreams, and then to develop a detailed and reliable content analysis scale with which it is possible to empirically explore and quantify threatening events in dreams. The second step was to seek answers to the following questions derived from the TST: How frequent threatening events are in dreams? What kind of qualities these events have? How threatening events in dreams relate to the most recently encoded or the most salient memory traces of threatening events experienced in waking life? What are the effects of exposure to severe waking life threat on dreams? The results reveal that threatening events are relatively frequent in dreams, and that the simulated threats are realistic. The most common threats include aggression, are targeted mainly against the dream self, and include simulations of relevant and appropriate defensive actions. Further, real threat experiences activate the threat simulation system in a unique manner, and dream content is modulated by the activation of long term episodic memory traces with highest negative saliency. To sum up, most of the predictions of the TST tested in this thesis received considerable support. The TST presents a strong argument that explains the specific design of dreams as threat simulations. The TST also offers a plausible explanation for why dreaming would have been selected for: because dreaming interacted with the environment in such a way that enhanced fitness of ancestral humans. By referring to a single threat simulation mechanism it furthermore manages to explain a wide variety of dream content data that already exists in the literature, and to predict the overall statistical patterns of threat content in different samples of dreams. The TST and the empirical tests conducted to test the theory are a prime example of what a multidisciplinary approach to mental phenomena can accomplish. Thus far, dreaming seems to have always resided in the periphery of science, never regarded worth to be studied by the mainstream. Nevertheless, when brought to the spotlight, the study of dreaming can greatly benefit from ideas in diverse branches of science. Vice versa, knowledge learned from the study of dreaming can be applied in various disciplines. The main contribution of the present thesis lies in putting dreaming back where it belongs, that is, into the spotlight in the cross-road of various disciplines.

Validation of plant dynamic model by online and laboratory measurements – a tool to predict online COD loads out of production of mechanical printing papers

COD discharges out of processes have increased in line with elevating brightness demands for mechanical pulp and papers. The share of lignin-like substances in COD discharges is on average 75%. In this thesis, a plant dynamic model was created and validated as a means to predict COD loading and discharges out of a mill. The assays were carried out in one paper mill integrate producing mechanical printing papers. The objective in the modeling of plant dynamics was to predict day averages of COD load and discharges out of mills. This means that online data, like 1) the level of large storage towers of pulp and white water 2) pulp dosages, 3) production rates and 4) internal white water flows and discharges were used to create transients into the balances of solids and white water, referred to as “plant dynamics”. A conversion coefficient was verified between TOC and COD. The conversion coefficient was used for predicting the flows from TOC to COD to the waste water treatment plant. The COD load was modeled with similar uncertainty as in reference TOC sampling. The water balance of waste water treatment was validated by the reference concentration of COD. The difference of COD predictions against references was within the same deviation of TOC-predictions. The modeled yield losses and retention values of TOC in pulping and bleaching processes and the modeled fixing of colloidal TOC to solids between the pulping plant and the aeration basin in the waste water treatment plant were similar to references presented in literature. The valid water balances of the waste water treatment plant and the reduction model of lignin-like substances produced a valid prediction of COD discharges out of the mill. A 30% increase in the release of lignin-like substances in the form of production problems was observed in pulping and bleaching processes. The same increase was observed in COD discharges out of waste water treatment. In the prediction of annual COD discharge, it was noticed that the reduction of lignin has a wide deviation from year to year and from one mill to another. This made it difficult to compare the parameters of COD discharges validated in plant dynamic simulation with another mill producing mechanical printing papers. However, a trend of moving from unbleached towards high-brightness TMP in COD discharges was valid.

Literature review on permanent magnet generators design and dynamic behavior

This paper is a literature review which describes the construction of state of the art of permanent magnet generators and motors constructing and discusses the current and possible application of these machines in industry. Permanent magnet machines are a well-know class of rotating and linear electric machines used for many years in industrial applications. A particular interest for permanent magnet generators is connected with wind mills, which seem to be becoming increasingly popular nowadays. Geared and direct-driven permanent magnet generators are described. A classification of direct-driven permanent magnet generators is given. Design aspects of permanent magnet generators are presented. Permanent magnet generators for wind turbines designs are highlighted. Dynamics and vibration problems of permanent magnet generators covered in literature are presented. The application of the Finite Element Method for mechanical problems solution in the field of permanent magnet generators is discussed.

Dimensioning DC-voltage capacitor for a DC-distribution system and dynamic analysis

Technical analysis of Low Voltage Direct Current (LVDC) distribution systems shows that in LVDC transmission the customer voltage quality is higher. One of the problems in LVDC distribution networks that converters both ends of the DC line are required. Because of the converters produce not pure DC voltage, but some fluctuations as well, the huge electrolytic capacitors are required to reduce voltage distortions in the DC-side. This thesis master’s thesis is focused on calculating required DC-link capacitance for LVDC transmission and estimation of the influence of different parameters on the voltage quality. The goal is to investigate the methods of the DC-link capacitance estimation and location in the transmission line.

Creating dynamic continuous improvement system for Larox Corporation

Today´s organizations must have the ability to react to rapid changes in the market. These rapid changes cause pressure to continuously find new efficient ways to organize work practices. Increased competition requires businesses to become more effective and to pay attention to quality of management and to make people to understand their work's impact on the final result. The fundamentals in continmuois improvement are systematic and agile tackling of indentified individual process constraints and the fact tha nothin finally improves without changes. Successful continuous improvement requires management commitment, education, implementation, measurement, recognition and regeneration. These ingredients form the foundation, both for breakthrough projects and small step ongoing improvement activities. One part of the organization's management system are the quality tools, which provide systematic methodologies for identifying problems, defining their root causes, finding solutions, gathering and sorting of data, supporting decision making and implementing the changes, and many other management tasks. Organizational change management includes processes and tools for managing the people in an organizational level change. These tools include a structured approach, which can be used for effective transition of organizations through change. When combined with the understanding of change management of individuals, these tools provide a framework for managing people in change,