Antennimittausjärjestelmän toteutus ja ominaisuuksien määrittäminen

Diplomityössä tarkasteltiin antennien säteilykuviomittauksiin käytettävien antennimittaratojen ominaisuuksia. Sovelletun elektroniikan laboratorion antennimittaradasta kehitettiin toimiva säteilykuvion mittausjärjestelmä, johon kuuluvat radiokaiuton kammio, suuntauskoneisto ja antennikannakkeet, HP 8720D -piirianalysaattori ja RF-kaapelointi sekä valmistutetut mitta-antennitorvet. Työssä vertailtiin koaksiaalikaapeleita ja valittiin antennimittaukseen soveltuvat. 1,70–2,60 GHz:n taajuusalueen mittastandardiksi suunniteltiin torviantenni, jonka kaksi prototyyppiä valmistutettiin konetekniikan osastolla. Torviantennien ominaisuudet mitattiin. Antennimittaradan ominaisuudet ja soveltuvuus erilaisiin antennimittauksiin selvitettiin sekä teoreettisesti että mittauksin.

Titaanisen valkaisutornin korjaussuunnitelma

Tämän työn tarkoituksena on poistaa toistuvasti esiintyneet vauriot titaanisessa valkaisutornissa Kuusankosken paperitehtailla. Vauriot esiintyivät melko pian käyttöönoton jälkeen ja niitä esiintyi toistuvasti jokaisen korjauksen jälkeen. Jatkuvatoimisen prosessin vuoksi käyttökatkokset eivät olleet suotavia. Aikataulu suunnittelulle ja korjaukselle oli erittäin tiukka, jolloin kenttämittauksia ei ollut mahdollista tehdä laskelmien tueksi. Tämän vuoksi tähän työtön parhaiten soveltuvaksi menetelmäksi valittiin FEA. Alkuperäisessä rakenteessa pääsäiliöön oli hitsattu pintatasku, jota käytettiin välisäiliönä varastoimaan suuri määrä vaarallista nestettä. Tämä aiheutti valkaisutornin vaipalle murtumia ja vuotoja sekä suuronnettomuuden riskin koko valkaisutornille. Kuormitustietojen puutteesta johtuen kuormitukset mallinnettiin virtuaalisesti FE-menetelmällä ja analyyttisin keinoin. Kuormitusten suuruudet arvioitiin konservatiivisesti. Tämän työn tärkein oivallus oli määritellä uudelleen pintataskun toiminto siten, että sitä ei enää käytetty nesteen välivarastona, vaan ohjaimena nesteelle. Tämä innovatiivinen ongelmankorjauskonsepti on havaittu onnistuneeksi, koska vaurioita ei ole enää esiintynyt viimeisimmän korjauksen jälkeen.

Typpioksiduuli- ja metaaniemissiot metsätalousalueiden puskurivyöhykkeiltä

Aim of this study was to investigate the means to reduce nutrient flows to water systems. Focus in this study was to examine peatland buffer zones as a solution to protect water bodies as well as to examine methane and nitrous oxide release from buffer zones. The literature survey covers a review of research which has been done till this day concerning the effects of forestry on water bodies. It also contains a review of the significance of forests and mires in hydrological cycle, effects of forestry on nutrient loads to water systems and a review of different solutions to diminish it. The solutions contain ditch shaping, submerged dams, sludge sumps, sedimentation ponds and buffer zones. The literature survey also covers nitrous oxide and methane gas emissions from buffer zones. Methane and nitrous oxide emissions from six different mires were studied during the summer of 2007. Measurements were conducted once a month using the static chamber method. Emissions of methane and nitrous oxide were calculated. Effects of water table level and peat temperature on emissions were also studied. The results showed a tendency to increased methane-emissions from natural peat lands when compared with restored buffer zones. The results showed also a tendency to increased CH4 emissions and decreased NO2 emissions with rising level of water table. Other mechanisms that influence emissions are vegetation composition and peat temperature. Considering the global warming as a result of increased greenhouse gas emissions, the emissions of CH4 and NO2 measured in the present study were not particularly high.

Imprecise measurements in quantum mechanics

In this thesis the structure and properties of imprecise quantum measurements are investigated. The starting point for this investigation is the representation of a quantum observable as a normalized positive operator measure. A general framework to describe measurement inaccuracy is presented. Requirements for accurate measurements are discussed, and the relation of inaccuracy to some optimality criteria is studied. A characterization of covariant observables is given in the case when they are imprecise versions of a sharp observable. Also the properties of such observables are studied. The case of position and momentum observables is studied. All position and momentum observables are characterized, and the joint positionmomentum measurements are discussed.

Validation of plant dynamic model by online and laboratory measurements – a tool to predict online COD loads out of production of mechanical printing papers

COD discharges out of processes have increased in line with elevating brightness demands for mechanical pulp and papers. The share of lignin-like substances in COD discharges is on average 75%. In this thesis, a plant dynamic model was created and validated as a means to predict COD loading and discharges out of a mill. The assays were carried out in one paper mill integrate producing mechanical printing papers. The objective in the modeling of plant dynamics was to predict day averages of COD load and discharges out of mills. This means that online data, like 1) the level of large storage towers of pulp and white water 2) pulp dosages, 3) production rates and 4) internal white water flows and discharges were used to create transients into the balances of solids and white water, referred to as “plant dynamics”. A conversion coefficient was verified between TOC and COD. The conversion coefficient was used for predicting the flows from TOC to COD to the waste water treatment plant. The COD load was modeled with similar uncertainty as in reference TOC sampling. The water balance of waste water treatment was validated by the reference concentration of COD. The difference of COD predictions against references was within the same deviation of TOC-predictions. The modeled yield losses and retention values of TOC in pulping and bleaching processes and the modeled fixing of colloidal TOC to solids between the pulping plant and the aeration basin in the waste water treatment plant were similar to references presented in literature. The valid water balances of the waste water treatment plant and the reduction model of lignin-like substances produced a valid prediction of COD discharges out of the mill. A 30% increase in the release of lignin-like substances in the form of production problems was observed in pulping and bleaching processes. The same increase was observed in COD discharges out of waste water treatment. In the prediction of annual COD discharge, it was noticed that the reduction of lignin has a wide deviation from year to year and from one mill to another. This made it difficult to compare the parameters of COD discharges validated in plant dynamic simulation with another mill producing mechanical printing papers. However, a trend of moving from unbleached towards high-brightness TMP in COD discharges was valid.

Photoelectric Measurements and Modeling of Bacteriorhodopsin

Recent technology has provided us with new information about the internal structures and properties of biomolecules. This has lead to the design of applications based on underlying biological processes. Applications proposed for biomolecules are, for example, the future computers and different types of sensors. One potential biomolecule to be incorporated in the applications is bacteriorhodopsin. Bacteriorhodopsin is a light-sensitive biomolecule, which works in a similar way as the light sensitive cells of the human eye. Bacteriorhodopsin reacts to light by undergoing a complicated series of chemical and thermal transitions. During these transitions, a proton translocation occurs inside the molecule. It is possible to measure the photovoltage caused by the proton translocations when a vast number of molecules is immobilized in a thin film. Also the changes in the light absorption of the film can be measured. This work aimed to develop the electronics needed for the voltage measurements of the bacteriorhodopsin-based optoelectronic sensors. The development of the electronics aimed to get more accurate information about the structure and functionality of these sensors. The sensors used in this work contain a thick film of bacteriorhodopsin immobilized in polyvinylalcohol. This film is placed between two transparent electrodes. The result of this work is an instrumentation amplifier which can be placed in a small space very close to the sensor. By using this amplifier, the original photovoltage can be measured in more detail. The response measured using this amplifier revealed two different components, which could not be distinguished earlier. Another result of this work is the model for the photoelectric response in dry polymer films.

Three Wavelength Optical Probe for Surface Roughness Measurements of Paper Samples

In the present diploma work optical inspection methods were used to investigate surface roughness of paper samples. A special measurement setup, which includes three laser light sources of three different wavelengths, photodetector and goniometer, was used to measure the reflected laser light properties. The intensity of the light reflected in specular direction was measured versus the laser incidence angle for reference metal sample. The value of roughness was estimated and compared to initially known value of metal sample roughness. Thus, the measurement equipment and method were validated. Then the reflected intensity was measured versus reflection angle at constant incidence angle for the same metal sample and paper samples under investigation. The final values of the surface roughness were obtained from the analysis of the reflected intensity dependence. The results are in good correlation with other research groups.

The Detector Control Systems for the CMS Resistive Plate Chamber at LHC

The RPC Detector Control System (RCS) is the main subject of this PhD work. The project, involving the Lappeenranta University of Technology, the Warsaw University and INFN of Naples, is aimed to integrate the different subsystems for the RPC detector and its trigger chain in order to develop a common framework to control and monitoring the different parts. In this project, I have been strongly involved during the last three years on the hardware and software development, construction and commissioning as main responsible and coordinator. The CMS Resistive Plate Chambers (RPC) system consists of 912 double-gap chambers at its start-up in middle of 2008. A continuous control and monitoring of the detector, the trigger and all the ancillary sub-systems (high voltages, low voltages, environmental, gas, and cooling), is required to achieve the operational stability and reliability of a so large and complex detector and trigger system. Role of the RPC Detector Control System is to monitor the detector conditions and performance, control and monitor all subsystems related to RPC and their electronics and store all the information in a dedicated database, called Condition DB. Therefore the RPC DCS system has to assure the safe and correct operation of the sub-detectors during all CMS life time (more than 10 year), detect abnormal and harmful situations and take protective and automatic actions to minimize consequential damages. The analysis of the requirements and project challenges, the architecture design and its development as well as the calibration and commissioning phases represent themain tasks of the work developed for this PhD thesis. Different technologies, middleware and solutions has been studied and adopted in the design and development of the different components and a big challenging consisted in the integration of these different parts each other and in the general CMS control system and data acquisition framework. Therefore, the RCS installation and commissioning phase as well as its performance and the first results, obtained during the last three years CMS cosmic runs, will be

Design of Installation for Transport Measurements

In the present work the aim was to prepare an automatic installation for studies of galvanomagnetic effects in solids and to test it by calibration measurements. As a result required automatic installation was created in this work and test measurements were performed. Created setup automatically provides measurements of the magnetoresistance of the Hall effect with an accuracy of ± 2 µV in the temperature range 2 – 300 K and steady magnetic fields up to 6 T. The test measurements of the glassy carbon samples showed that the setup is reliable, has high sensitivity and is easy to use. The results obtained in the research process are pioneer and will be separately analyzed.

Electric field measurements using scanning electron microscope

The main idea of this diploma work is to study electric field distribution on the micro level. For this purpose a silicon edgeless detector was chosen as the object of investigation and scanning electron microscope as an investigation tool. Silicon edgeless detector is an important part of installation for studying proton-proton interactions in TOTEM experiment at Large Hadron Collider. For measurement of electric field distribution inside scanning electron microscope a voltage contrast method was applied.

Metaanin muodostumisen mallintaminen kaatopaikalla

Methane-rich landfill gas is generated when biodegradable organic wastes disposed of in landfills decompose under anaerobic conditions. Methane is a significant greenhouse gas, and landfills are its major source in Finland. Methane production in landfill depends on many factors such as the composition of waste and landfill conditions, and it can vary a lot temporally and spatially. Methane generation from waste can be estimated with various models. In this thesis three spreadsheet applications, a reaction equation and a triangular model for estimating the gas generation were introduced. The spreadsheet models introduced are IPCC Waste Model (2006), Metaanilaskentamalli by Jouko Petäjä of Finnish Environment Institute and LandGEM (3.02) of U.S. Environmental Protection Agency. All these are based on the first order decay (FOD) method. Gas recovery methods and gas emission measurements were also examined. Vertical wells and horizontal trenches are the most commonly used gas collection systems. Emission measurements chamber method, tracer method, soil core and isotope measurements, micrometeorological mass-balance and eddy covariance methods and gas measuring FID-technology were discussed. Methane production at Ämmässuo landfill of HSY Helsinki Region Environmental Services Authority was estimated with methane generation models and the results were compared with the volumes of collected gas. All spreadsheet models underestimated the methane generation at some point. LandGEM with default parameters and Metaanilaskentamalli with modified parameters corresponded best with the gas recovery numbers. Reason for the differences between evaluated and collected volumes could be e.g. that the parameter values of the degradable organic carbon (DOC) and the fraction of decomposable degradable organic carbon (DOCf) do not represent the real values well enough. Notable uncertainty is associated with the modelling results and model parameters. However, no simple explanation for the discovered differences can be given within this thesis.

Online Ultrasound Measurements of Membrane Compaction

There are several filtration applications in the pulp and paper industry where the capacity and cost-effectiveness of processes are of importance. Ultrafiltration is used to clean process water. Ultrafiltration is a membrane process that separates a certain component or compound from a liquid stream. The pressure difference across the membrane sieves macromolecules smaller than 0.001-0.02 μm through the membrane. When optimizing the filtration process capacity, online information about the conditions of the membrane is needed. Fouling and compaction of the membrane both affect the capacity of the filtration process. In fouling a “cake” layer starts to build on the surface of the membrane. This layer blocks the molecules from sieving through the membrane thereby decreasing the yield of the process. In compaction of the membrane the structure is flattened out because of the high pressure applied. The higher pressure increases the capacity but may damage the structure of the membrane permanently. Information about the compaction is needed to effectively operate the filters. The objective of this study was to develop an accurate system for online monitoring of the condition of the membrane using ultrasound reflectometry. Measurements of ultrafiltration membrane compaction were made successfully utilizing ultrasound. The results were confirmed by permeate flux decline, measurements of compaction with a micrometer, mechanical compaction using a hydraulic piston and a scanning electron microscope (SEM). The scientific contribution of this thesis is to introduce a secondary ultrasound transducer to determine the speed of sound in the fluid used. The speed of sound is highly dependent on the temperature and pressure used in the filters. When the exact speed of sound is obtained by the reference transducer, the effect of temperature and pressure is eliminated. This speed is then used to calculate the distances with a higher accuracy. As the accuracy or the resolution of the ultrasound measurement is increased, the method can be applied to a higher amount of applications especially for processes where fouling layers are thinner because of smaller macromolecules. With the help of the transducer, membrane compaction of 13 μm was measured in the pressure of 5 bars. The results were verified with the permeate flux decline, which indicated that compaction had taken place. The measurements of compaction with a micrometer showed compaction of 23–26 μm. The results are in the same range and confirm the compaction. Mechanical compaction measurements were made using a hydraulic piston, and the result was the same 13 μm as obtained by applying the ultrasound time domain reflectometry (UTDR). A scanning electron microscope (SEM) was used to study the structure of the samples before and after the compaction.