Fiber Laser Cutting of Mild Steel

Fiber laser for materials processing have undergone a rapid development in the pastseveral years. As fiber laser provides a combination of high beam quality and awavelength that is easily absorbed by metal surfaces, the named future laser isexpected to challenge the CO2 and Nd:YAG lasers in the area of metal cutting. This thesis studied the performance of fiber laser cutting mild steel. In the literature review part, it introduced the laser cutting principle and the principle of fiber laser including the newest development of fiber laser cuttingtechnology. Because the fiber laser cutting mild steel is a very young technology, a preliminary test was made in order to investigate effect of the cutting parameters on cut quality. Then the formal fiber laser cutting experiment was madeby using 3 mm thickness S355 steel with oxygen as assistant gas. The experimentwas focused on the cut quality with maximum cutting speed and minimum oxygen gas pressure. And the cut quality is mainly decided by the kerf width, perpendicularity tolerance, surface roughness and striation patterns. After analysis the cutting result, several conclusions were made. Although the best result got in the experiment is not perfect as predicted, the whole result of the test can be accepted. Compared with CO2 laser, a higher cutting speed was achieved by fiber laser with very low oxygen gas pressure. A further improvement about the cutting quality might be possible by proper selection of process parameters. And in order to investigate the cutting performance more clearly, a future study about cutting different thickness mild steel and different shape was recommended.

Experimental and Numerical Analysis of Different Volutes in a Centrifugal Compressor

In a centrifugal compressor the flow around the diffuser is collected and led to the pipe system by a spiral-shaped volute. In this study a single-stage centrifugal compressor with three different volutes is investigated. The compressorwas first equipped with the original volute, the cross-section of which was a combination of a rectangle and semi-circle. Next a new volute with a fully circular cross-section was designed and manufactured. Finally, the circular volute wasmodified by rounding the tongue and smoothing the tongue area. The overall performance of the compressor as well as the static pressure distribution after the impeller and on the volute surface were measured. The flow entering the volute was measured using a three-hole Cobra-probe, and flow visualisations were carriedout in the exit cone of the volute. In addition, the radial force acting on theimpeller was measured using magnetic bearings. The complete compressor with thecircular volute (inlet pipe, full impeller, diffuser, volute and outlet pipe) was also modelled using computational fluid dynamics (CFD). A fully 3-D viscous flow was solved using a Navier-Stokes solver, Finflo, developed at Helsinki University of Technology. Chien's k-e model was used to take account of the turbulence. The differences observed in the performance of the different volutes were quite small. The biggest differences were at low speeds and high volume flows,i.e. when the flow entered the volute most radially. In this operating regime the efficiency of the compressor with the modified circular volute was about two percentage points higher than with the other volutes. Also, according to the Cobra-probe measurements and flow visualisations, the modified circular volute performed better than the other volutes in this operating area. The circumferential static pressure distribution in the volute showed increases at low flow, constant distribution at the design flow and decrease at high flow. The non-uniform static pressure distribution of the volute was transmitted backwards across the vaneless diffuser and observed at the impeller exit. At low volume flow a strong two-wave pattern developed into the static pressure distribution at the impeller exit due to the response of the impeller to the non-uniformity of pressure. The radial force of the impeller was the greatest at the choke limit, the smallest atthe design flow, and moderate at low flow. At low flow the force increase was quite mild, whereas the increase at high flow was rapid. Thus, the non-uniformityof pressure and the force related to it are strong especially at high flow. Theforce caused by the modified circular volute was weaker at choke and more symmetric as a function of the volume flow than the force caused by the other volutes.

Critical flux and fouling in ultrafiltration of proteins

In this thesis different parameters influencing critical flux in protein ultrafiltration and membrane foul-ing were studied. Short reviews of proteins, cross-flow ultrafiltration, flux decline and criticalflux and the basic theory of Partial Least Square analysis (PLS) are given at the beginning. The experiments were mainly performed using dilute solutions of globular proteins, commercial polymeric membranes and laboratory scale apparatuses. Fouling was studied by flux, streaming potential and FTIR-ATR measurements. Critical flux was evaluated by different kinds of stepwise procedures and by both con-stant pressure and constant flux methods. The critical flux was affected by transmembrane pressure, flow velocity, protein concentration, mem-brane hydrophobicity and protein and membrane charges. Generally, the lowest critical fluxes were obtained at the isoelectric points of the protein and the highest in the presence of electrostatic repulsion between the membrane surface and the protein molecules. In the laminar flow regime the critical flux increased with flow velocity, but not any more above this region. An increase in concentration de-creased the critical flux. Hydrophobic membranes showed fouling in all charge conditionsand, furthermore, especially at the beginning of the experiment even at very low transmembrane pressures. Fouling of these membranes was thought to be due to protein adsorption by hydrophobic interactions. The hydrophilic membranes used suffered more from reversible fouling and concentration polarisation than from irreversible foul-ing. They became fouled at higher transmembrane pressures becauseof pore blocking. In this thesis some new aspects on critical flux are presented that are important for ultrafiltration and fractionation of proteins.

Hapettavan BIMODES-mikrobientorjuntamenetelmän vaikutukset paperikoneella

The aim of this study was to examine the effects of oxidising BIMODES microbiological control program on three paper machine process. The chemicals used in BIMODES program are sodium hypochlorite (NaOCl) and bromo-chloro-di-methyl-hydantoin (BCDMH). The literary part of this study discusses the microbiological problems in paper making industry, describes functional mechanisms of oxidants and also introduces the BIMODES- program. In the experimental part the aim was to examine the effects of BIMODES in three different paper machines. The purpose was to find out the effects and changes in wet end chemistry, bacterial counts, in the other additives and also in the sheet defects and holes. The study also examines what are the most important measurements to control BIMODES dosing. In addition the optimal dosing level for each machine was tried to find out. It was found that there is a clear correlation between the total chlorine level and bacterial counts. Changes in the BIMODES dosing level can be measured by redox potential, but the correlation is very poor. BIMODES program doesn’t have straight influence to pH values, but if dosage level is too low the bacterial activity can affect degreasing in the pH value. In this study couldn’t find any consequential effects for the other additives by using BIMODES. In addition the optimal dosing levels were found and by following correct halogen levels it is possible to decrease bacterial levels for very low level.

Metsäteollisuuden lietteiden bioterminen kuivaus

Työssä tarkastellaan kompostointiin perustuvaa biotermistä kuivausprosessia, prosessiin vaikuttavia tekijöitä sekä sen soveltuvuutta metsäteollisuuden mekaanisesti kuivatun jätevesilietteen lisäkuivaukseen polttoa varten. Tutkimukseen kuuluvien paperitehtaiden lietteillä suoritettavien biotermisten kuivauskokeiden avulla tutkitaan tehtaiden lietteiden sopivuutta biotermiseen kuivaukseen. Lisäksi tehtaille suunnitellaan kuivauskokeiden ja paperitehtailla tehtävien selvitysten perusteella bioterminen kuivauslaitos. Suomen metsäteollisuus tuottaa nykyisin noin 400 000 – 500 000 kuiva-ainetonnia jätevedenpuhdistamolietteitä vuosittain. Tutkimukseen kuuluvan kahden tehdasintegraatin biologisilla puhdistamoilla syntyvien jätevesilietteiden määrät ovat keskimäärin 33 000 ja 15 000 kuiva-ainetonnia vuodessa. Ongelmana metsäteollisuudessa on jätevesilietteen alhainen kuiva-ainepitoisuus lietteen mekaanisen kuivauksen jälkeen. Tämä vaikeuttaa lietteen polttamista voimalaitoskattilassa ja lietteen poltosta talteen saatavan energian määrä jää vähäiseksi. Mekaanisesti kuivatun sekalietteen käsittely biotermisesti kuivaamalla mahdollistaa lietteen kuiva-ainepitoisuuden nostamisen yli 55 %:in kuiva-ainepitoisuuteen. Tämä helpottaa lietteen polton ongelmia ja kasvattaa lietteen poltosta talteen saatavan energian määrää. Bioterminen kuivaus soveltuu hyvin tutkimukseen kuuluvien tehtaiden sekalietteen kuivaukseen. Suositeltava sekalietteen lähtökuiva-ainepitoisuuden arvo on välillä 30 – 35 % ja tukiaineeksi lisättävän kuoren määrä noin 0,5 m3 yhtä lietekuutiota kohden. Kuivausprosessin kesto on tällöin 10 – 14 vuorokautta, kun haluttu lietepolttoaineen kuiva-ainepitoisuus on vähintään 55 %. Tehtaille suunnitelluissa laitoksissa käsiteltävä lietemäärä on noin 40 000 märkätonnia vuodessa. Tutkimukseen kuuluvalle paperitehtaalle yhdistetyn lietteenkuivausprosessin kustannukset ovat edullisimmat kun liete kuivataan ennen biotermistä kuivausta mekaanisesti 35 %:in kuiva-ainepitoisuuteen. Tällöin lietteenkäsittelyn hinnaksi tulee noin 150 mk/t.

Kiinteistösähköverkkojen laskentaohjelmiston valinta.

Jotta kiinteistösähköverkkojen laskentaohjelmia voidaan vertailla mielekkäästi keskenään, on tunnettava suunnitteluprosessin vaiheet ja tarvittavat laskelmat. Sähköverkon mitoituksessa tärkeitä tietoja ovat verkon oikosulkuteho, kuormitukset ja vikavirrat, joiden avulla määritellään tarvittavat suojaukset, johtojen poikkipinnat ja jännitteenalenemat. Tällä hetkellä markkinoilla olevia ohjelmia ovat esimerkiksi Ecodial, NolaWi, DOCWin, EDSA ja KUBS+. Kun painotetaan ohjelman hintaa, kieltä, verkon rakentamista, komponenttikirjastojen kokoa, solmupisteiden määrää, suojauksen selektiivisyyden tarkastamista ja kosketusjännitesuojauksen toiminnan toteamista sekä tuloksien esitystä niin ohjelmista parhaiten pärjäävät Ecodial ja DOCWin. Vertailun tuloksena ehdotetaan suunnittelutyöhön valittavaksi ohjelmaksi ABB:n DOCWin:a, joka täyttää parhaiten halutut ominaisuudet ja on lisäksi käyttökustannuksiltaan edullinen.

Ohutlevyn taivuttaminen pienerätuotannossa

Tutkimuksessa on selvitetty ohutlevyn taivuttamismenetelmien tärkeimmät kustannustekijät ja menetelmien taloudelliset käyttöalueet. Vertailtavina menetelminä on käsinsärmäys, robotisoitu särmäys, taivutusautomaatti ja taivutuskone. Tulosta on sovellettu Hackman Metos Oy:n keittiölaitteiden tuotantoon. Tutkimusmenetelminä oli haastattelututkimus, kirjallisuustutkimus, työntutkimustulosten käyttö, ryhmäteknologian soveltaminen ja kokeellinen tutkimus. Särmäysrobotin tärkein kustannustekijä on ohjelmointiaika, mikä vaikuttaa ratkaisevasti sen soveltuvuuteen pienerätuotantoon. Nykyisten särmäyssolujen taloudellinen käyttöalue on tuhansien kappaleiden vuosivolyymi satojen kappaleiden eräkoolla. taivutusautomaatin ohjelmointi- ja asetusajat ovat erittäin lyhyet ja sen tärkein kustannustekijä on käyttöaste. Mikäli käyttöaste on korkea, taivutusautomaatti on kannattava pienerätuotannossa pienille vuosivolyymeille. Taivutusautomaatin käyttöönotossa tuotteiden suunnittelu on tärkeä tekijä, sillä särmättäväksi suunnitellut osat eivät välttämättä sovellu taivutusautomaatilla taivutettavaksi. Taivutuskoneen investointikustannus on alhaisempi kuin särmäyspuristimen, mutta sillä on paljon tuotteen valmistettavuuden liittyviä rajoituksia. Taivutuskone on kannattava investointi, mikäli tuotannossa on paljon levyjä, joiden taivutukset ovat samaan suuntaan ja ne vaativat kaksi särmääjää. Tutkimuksen perusteella Hackman Metso Oy:ssä teknis-taloudellisin taivutusmenetelmä on käsinsärmäys. Tuotannon kasvaessa taivutusautomaatti tulee olemaan särmäysrobottia edullisempi. Taivutuskoneella on niin paljon valmistettavuusrajoituksia, että se ei sovellu yrityksen tuotantoon.

Sisäisten donorien vaikutus Polypropeeni Ziegler-Natta katalyytissä

Tässä työssä tutkittiin erilaisten sisäisten donorien vaikutusta polypropeenin ominaisuuksiin käytettäessä Ziegler-Natta-katalyyttiä, joka valmistettiin Borealiksen aiemmin kehittämällä kaksifaasimenetelmällä. Tällä uudella menetelmällä katalyytti voidaan valmistaa ilman lisättyä sisäistä donoria ja kantajaa. Katalyyttihiukkaset saadaan kaksifaasisysteemin ansiosta muodoltaan pyöreiksi. Työn kokeellisessa osassa valmistettiin erilaisia Mg-komplekseja, jossa sisäinen donori muodostuu in-situ alkoholin ja karboksyylihappokloridin reagoidessa keskenään. Katalyyttisynteesissä Mg-kompleksi reagoi TiCl4:n kanssa. Saatujen katalyyttien ominaisuuksia testattiin polymeroimalla niillä propeenia 70 °C:ssa tunnin ajan. Polymeerien ominaisuuksia tutkittiin useiden eri karakterisointimenetelmien avulla. Lisäksi tutkittiin mahdollisuutta valmistaa katalyytti, joka ei sisältäisi ftalaattia. Työssä havaittiin, että katalyytin valmistusmenetelmä on käyttökelpoinen myös muilla sisäisillä donoreilla kuin referenssinä käytetyllä DOP:lla. Kaksiliuosfaasi-systeemi saatiin aikaan myös kahdella muulla työssä tutkitulla sisäisellä donorilla. Lisäksi faasitasapainokokeissa kahden liuosfaasin systeemi saatiin aikaan sisäisellä donorilla, joka ei sisältänyt ftalaattia. Kyseisellä katalyytillä havaittiin olevan muista katalyyteistä poikkeavia ominaisuuksia. Esimerkiksi se antoi matalamman isotaktisuuden kuin referenssikatalyytti ja se saattaisikin soveltua matalan isotaktisuuden pehmeille tuotteille. Työssä kokeiltiin yhdellä uudella katalyytillä myös eteenin polymerointia, sillä katalyytin donoripitoisuus oli hyvin matala. Katalyytin aktiivisuus eteenipolymeroinnissa oli varsin hyvä.

Cost-Efficiency of Birch Sprinkling in Kraft Pulping

Työn tavoitteena oli selvittää koivun kasteluvarastoinnin kannattavuus selluteollisuudessa. Lisäksi tutkittiin, kuinka kastelu vaikuttaa puuaineeseen varastoinnin aikana ja kuinka koivun kasteluvarastointi vaikuttaa puun kuorintaan ja haketukseen, keitettävyyteen, vaalenevuuteen sekä sellun laatuun. Enocellin puukentälle rakennettiin kasteluvarasto, jossa varastoitiin 40,000 m3sob koivua. Kastelu oli päällä huhtikuusta lokakuuhun asti. Kastelun vaikutusta puuaineen muutoksiin arvioitiin lahotutkimusten avulla. Tehdaskoeajoissa verrattiin tuoretta, kasteluvarastoitua ja kuivavarastoitua koivua. Puuaines säilyi lähes muuttumattomana yhden kesän kasteluvarastoinnissa. Kastellulla koivulla terveen puun osuus oli yli 85 % kesän lopussa, kun se oli alle 20 % kuivavarastoidulla koivulla. Kuorinnan puuhäviö laskee selvästi kastelukoivulla ja myös hakkeen laatu oli parempaa kuin kuivavarastoidulla koivulla. Kastelukoivulla hakkeen kuoripitoisuus oli vain 0.13 %. Kuoren kuiva-aine oli 12 prosenttiyksikköä alhaisempi kuin kuivalla koivulla, mutta kuoren lämpöarvossa ero oli vain 1 €/ADt. Varastointimenetelmällä ei ollut vaikutusta hakkeen keitettävyyteen, mutta tuoreella puulla keitettävyys oli parempi kuin varastoidulla puulla. Sellun asetoniuutepitoisuus oli samalla tasolla tuoreella ja kastellulla puulla. Kuivalla syyspuulla uutetaso oli korkeampi, vaikka hartsisaippuan annostusta nostettiin 10 kg/ADt. Betulinolitaso oli kastellulla puulla erittäin alhainen puun hyvän kuoriutuvuuden vuoksi. Kastellun ja tuoreen puun vaalenevuus oli parempi kuin kuivalla puulla. Aktiivikloorin kulutus oli 3 – 4 kg/ADt alhaisempi kuin kuivalla syyspuulla. Puun varastoinnilla ei ollut vaikutusta sellun laatuun. Koivun kasteluvarastoinnin kannattavuus on erittäin hyvä. Tuotantokustannukset määritettiin tuoreelle, kastellulle, kierrätetylle sekä kuivalle koivulle. Kasteluvarastointi laskee tuotantokustannuksia noin 10 €/ADt verrattuna kierrätettyyn koivuun. Kuivavarastoidun puun käyttö nostaa tuotantokustannuksia noin 5 €/ADt verrattuna kastelukoivuun. Kierrätetyn ja kuivavarastoidun puun kustannusero johtuu kierrätyskustannuksista. Kasteluvarastolle, jota käytettiin kesällä 2004, takaisinmaksuaika on vain 0.4 vuotta. Jos tavoiteltu takaisinmaksuaika olisi kaksi vuotta, niin perusinvestointi 80,000 m3sob varastolle voisi maksaa noin 370 k€.

Highly functional binding surface for miniaturised solid-phase immunoassays. - A spot story -

Several bioaffinity assays are based on the detection of an analyte which is bound on a solid substrate via biochemical interaction. These so called solid phase assays are based on the adhesion of the primary binding partner on a solid surface, which then binds the analyte to be detected. In this thesis work a novel solid phase based assay technology, known as spot technology, was developed. The spot technology is based on combination of high-capacity solid phases, concentrated in a spot format, utilising modified streptavidin molecules and recombinant antibody fragments. The reduction of the solid phase binding surface to a size of a spot enabled denser binding of the target molecules, providing improved signal intensities and signal-to-background ratio when applied in different solid phase immunoassays. Streptavidin-biotin interactions are commonly utilised in numerous different bioaffinity assays and the ultimate nature of streptavidin to bind biotin is among the strongest non-covalent interaction reported between two biomolecules. In this study native core streptavidin was chemically modified to provide polymerised streptavidin molecules with altered adsorption properties. These streptavidin conjugates, when coated onto polystyrene surface, provided enhanced biotin binding capacity and surface stability when compared to a reference coating constructed with native streptavidin. Furthermore, the combination of chemically modified streptavidin, sitespecifically biotinylated antibody fragments and the spot coating technology provided highly dense solid phase coating with improved binding properties. The performance of the spot assay technology was further demonstrated in different immunoassay configurations. Human thyroid stimulating hormone (TSH) and human cardiac troponin I (cTnI) were used as model analytes to show the applicability of the highly sensitive spot-based solid-phase immunoassay for detection of very low levels of analytes. It was demonstrated that the spot technology provided an assay concept with enhanced sensitivity and short turn-around times, characteristics that are highly suitable for point-of-care applications.

Magnetic and transport properties of InGaAs quantum wells with Mn

In the present work structural, magnetic and transport properties of InGaAs quantum wells (QW) prepared by MBE with an remote Mn layer are investigated. By means of high-resolution X-ray diffractometry the structure of the samples is analyzed. It is shown that Mn ions penetrate into the QW. Influence of the thickness of GaAs spacer and annealing at 286 ºС on the properties of the system is shown. It is shown that annealing of the samples led to Mn activation and narrowing of the Mn layer. Substantial role of 2D holes in ferromagnetic ordering in Mn layer is shown. Evidence for that is observation of maximum at 25 – 55 K on the resistivity temperature dependence. Position of maximum, which is used for quantitative assessment of the Curie temperature, correlates with calculations of the Curie temperature for structures with indirect interaction via 2D holes’ channel. Dependence of the Curie temperature on the spacer thickness shows, that creation of applicable spintronic devices needs high-precision equipment to manufacture extra fine structures. The magnetotransport measurements show that charge carrier mobility is very low. This leads to deficiency of the anomalous Hall effect. At the same time, magnetic field dependences of the magnetization at different temperatures demonstrate that systems are ferromagnetically ordered. These facts, most probably, give evidence of presence of the ferromagnetic MnAs clusters.

Effects of Weight Loss on Adipose Tissue, Liver and Heart Metabolism in Humans

Obesity has become the leading cause of many chronic diseases, such as type 2 diabetes and cardiovascular diseases. The prevalence of obesity is high in developed countries and it is also a major cause of the use of health services. Ectopic fat accumulation in organs may lead to metabolic disturbances, such as insulin resistance.Weight loss with very-low-energy diet is known to be safe and efficient. Weight loss improves whole body insulin sensitivity, but its effects on tissue and organ level in vivo are not well known. The aims of the studies were to investigate possible changes of weight loss in glucose and fatty acid uptake and perfusion and fat distribution at tissue and organ level using positron emission tomography and magnetic resonance imaging and spectroscopy in 34 healthy obese subjects. The results showed that whole-body insulin sensitivity increased after weight loss with very-low-energy diet and this is associated with improved skeletal muscle insulin-stimulated glucose uptake, but not with adipose tissue, liver or heart glucose uptake. Liver insulin resistance decreased after weight loss. Liver and heart free fatty acid uptakes decreased concomitantly with liver and heart triglyceride content. Adipose tissue and myocardial perfusion decreased. In conclusion, enhanced skeletal muscle glucose uptake leads to increase in whole-body insulin sensitivity when glucose uptake is preserved in other organs studied. These findings suggest that lipid accumulation found in the liver and the heart in obese subjects without co-morbidies is in part reversible by reduced free fatty acid uptake after weight loss. Reduced lipid accumulation in organs may improve metabolic disturbances, e.g. decrease liver insulin resistance. Keywords: Obesity, weight loss, very-low-energy diet, adipose tissue metabolism, liver metabolism, heart metabolism, positron emission tomography

Salient Pole Synchronous Machine Modelling in an Industrial Direct Torque Controlled Drive Application

Synchronous motors are used mainly in large drives, for example in ship propulsion systems and in steel factories' rolling mills because of their high efficiency, high overload capacity and good performance in the field weakening range. This, however, requires an extremely good torque control system. A fast torque response and a torque accuracy are basic requirements for such a drive. For large power, high dynamic performance drives the commonly known principle of field oriented vector control has been used solely hitherto, but nowadays it is not the only way to implement such a drive. A new control method Direct Torque Control (DTC) has also emerged. The performance of such a high quality torque control as DTC in dynamically demanding industrial applications is mainly based on the accurate estimate of the various flux linkages' space vectors. Nowadays industrial motor control systems are real time applications with restricted calculation capacity. At the same time the control system requires a simple, fast calculable and reasonably accurate motor model. In this work a method to handle these problems in a Direct Torque Controlled (DTC) salient pole synchronous motor drive is proposed. A motor model which combines the induction law based "voltage model" and motor inductance parameters based "current model" is presented. The voltage model operates as a main model and is calculated at a very fast sampling rate (for example 40 kHz). The stator flux linkage calculated via integration from the stator voltages is corrected using the stator flux linkage computed from the current model. The current model acts as a supervisor that prevents only the motor stator flux linkage from drifting erroneous during longer time intervals. At very low speeds the role of the current model is emphasised but, nevertheless, the voltage model always stays the main model. At higher speeds the function of the current model correction is to act as a stabiliser of the control system. The current model contains a set of inductance parameters which must be known. The validation of the current model in steady state is not self evident. It depends on the accuracy of the saturated value of the inductances. Parameter measurement of the motor model where the supply inverter is used as a measurement signal generator is presented. This so called identification run can be performed prior to delivery or during drive commissioning. A derivation method for the inductance models used for the representation of the saturation effects is proposed. The performance of the electrically excited synchronous motor supplied with the DTC inverter is proven with experimental results. It is shown that it is possible to obtain a good static accuracy of the DTC's torque controller for an electrically excited synchronous motor. The dynamic response is fast and a new operation point is achieved without oscillation. The operation is stable throughout the speed range. The modelling of the magnetising inductance saturation is essential and cross saturation has to be considered as well. The effect of cross saturation is very significant. A DTC inverter can be used as a measuring equipment and the parameters needed for the motor model can be defined by the inverter itself. The main advantage is that the parameters defined are measured in similar magnetic operation conditions and no disagreement between the parameters will exist. The inductance models generated are adequate to meet the requirements of dynamically demanding drives.

Kehittyneiden hitsausprosessien soveltuvuus alumiinin ja hiiliterästen hitsaukseen

Diplomityössä tutkitaan hitsausprosessien kehitystä. Työn kirjallisen osan alku kuvaa hitsauksen nykypäivää ja tulevaisuutta sekä millainen on hitsaava Suomi. Kehittyneiden hitsausprosessien tarkastelu on jaettu hiiliterästen ja alumiinien hitsausprosesseihin. Hiiliteräksien hitsauksen osalta työssä esitellään kitkahitsaus pyörivällä työkalulla, muunnettu lyhytkaarihitsaus, laserhitsaus, laser-hybridihitsaus ja kapearailohitsaus. Alumiinien hitsauksen osalta työssä esitellään laserhitsaus, muunnettu lyhytkaarihitsaus, kitkahitsaus pyörivällä työkalulla ja vaihtovirta MIG hitsaus. Diplomityön käytännönosuudessa todennettiin hitsausprosessien kehitys. Ensimmäisissä hitsauskokeissa hitsattiin merialumiinia eri kaarityypeillä. Vertailua tehdään pulssihitsauksen, lankapulssihitsauksen sekä CMT-kaarihitsauksen välillä. Koehitsaukset osoittavat CMT-hitsauksen tuottavan MIG-pulssihitsausta pienemmät hitsausmuodonmuutokset. CMT-hitsauksessa alumiinin oksidikerros aiheuttaa MIGpulssihitsausta vähemmän ongelmia, sillä kaari syttyy varmemmin suurillakin hitsausnopeuksilla, eikä hitsiin synny huokosia. Hitsausnopeudella 40 cm/min lankapulssihitsauksella ja MIG-pulssihitsauksella päittäisliitoksena hitsattujen vesileikattujen alumiinikappaleiden hitseihin ei syntynyt huokosia. Kokeen perusteella voidaan todeta, ettei oksidikerroksella ollut vaikutusta hitsin onnistumiseen. Hitsauskokeiden toinen osio tutkii hiilimangaaniteräksisen T-palkin kuitulaserhitsausta. Viiden kilowatin laserteholla hitsattiin onnistuneesti viisi metriä pitkiä T-palkkeja hitsausnopeudella 2 m/min. Takymetrimittauksella ja Tritop 3D-koordinaattimittauksella todennettiin laserhitsatun T-palkin hitsausmuodonmuutosten olevan huomattavasti Twin-jauhekaarihitsauksella hitsattua T-palkkia pienemmät.

Conservation Genetics of Exploited Finnish Salmonid Fishes

Genetic diversity is one of the levels of biodiversity that the World Conservation Union (IUCN) has recognized as being important to preserve. This is because genetic diversity is fundamental to the future evolution and to the adaptive flexibility of a species to respond to the inherently dynamic nature of the natural world. Therefore, the key to maintaining biodiversity and healthy ecosystems is to identify, monitor and maintain locally-adapted populations, along with their unique gene pools, upon which future adaptation depends. Thus, conservation genetics deals with the genetic factors that affect extinction risk and the genetic management regimes required to minimize the risk. The conservation of exploited species, such as salmonid fishes, is particularly challenging due to the conflicts between different interest groups. In this thesis, I conduct a series of conservation genetic studies on primarily Finnish populations of two salmonid fish species (European grayling, Thymallus thymallus, and lake-run brown trout, Salmo trutta) which are popular recreational game fishes in Finland. The general aim of these studies was to apply and develop population genetic approaches to assist conservation and sustainable harvest of these populations. The approaches applied included: i) the characterization of population genetic structure at national and local scales; ii) the identification of management units and the prioritization of populations for conservation based on evolutionary forces shaping indigenous gene pools; iii) the detection of population declines and the testing of the assumptions underlying these tests; and iv) the evaluation of the contribution of natural populations to a mixed stock fishery. Based on microsatellite analyses, clear genetic structuring of exploited Finnish grayling and brown trout populations was detected at both national and local scales. Finnish grayling were clustered into three genetically distinct groups, corresponding to northern, Baltic and south-eastern geographic areas of Finland. The genetic differentiation among and within population groups of grayling ranged from moderate to high levels. Such strong genetic structuring combined with low genetic diversity strongly indicates that genetic drift plays a major role in the evolution of grayling populations. Further analyses of European grayling covering the majority of the species’ distribution range indicated a strong global footprint of population decline. Using a coalescent approach the beginning of population reduction was dated back to 1 000-10 000 years ago (ca. 200-2 000 generations). Forward simulations demonstrated that the bottleneck footprints measured using the M ratio can persist within small populations much longer than previously anticipated in the face of low levels of gene flow. In contrast to the M ratio, two alternative methods for genetic bottleneck detection identified recent bottlenecks in six grayling populations that warrant future monitoring. Consistent with the predominant role of random genetic drift, the effective population size (N_e) estimates of all grayling populations were very low with the majority of N_e estimates below 50. Taken together, highly structured local populations, limited gene flow and the small N_e of grayling populations indicates that grayling populations are vulnerable to overexploitation and, hence, monitoring and careful management using the precautionary principles is required not only in Finland but throughout Europe. Population genetic analyses of lake-run brown trout populations in the Inari basin (northernmost Finland) revealed hierarchical population structure where individual populations were clustered into three population groups largely corresponding to different geographic regions of the basin. Similar to my earlier work with European grayling, the genetic differentiation among and within population groups of lake-run brown trout was relatively high. Such strong differentiation indicated that the power to determine the relative contribution of populations in mixed fisheries should be relatively high. Consistent with these expectations, high accuracy and precision in mixed stock analysis (MSA) simulations were observed. Application of MSA to indigenous fish caught in the Inari basin identified altogether twelve populations that contributed significantly to mixed stock fisheries with the Ivalojoki river system being the major contributor (70%) to the total catch. When the contribution of wild trout populations to the fisheries was evaluated regionally, geographically nearby populations were the main contributors to the local catches. MSA also revealed a clear separation between the lower and upper reaches of Ivalojoki river system – in contrast to lower reaches of the Ivalojoki river that contributed considerably to the catch, populations from the upper reaches of the Ivalojoki river system (>140 km from the river mouth) did not contribute significantly to the fishery. This could be related to the available habitat size but also associated with a resident type life history and increased cost of migration. The studies in my thesis highlight the importance of dense sampling and wide population coverage at the scale being studied and also demonstrate the importance of critical evaluation of the underlying assumptions of the population genetic models and methods used. These results have important implications for conservation and sustainable fisheries management of Finnish populations of European grayling and brown trout in the Inari basin.