21 resultados para THREADING DISLOCATION DENSITIES
Resumo:
In this work temperature dependences of resistivity in zero field have been obtained for epitaxially grown Ga1_xMnxAs thin films with 6 % and 8 % Mn content in 50 300 K temperature range. Decrease of resistivity has been observed. Negative magnetoresistance has been explained by empirical spin dependent hopping model. Hall effect has been studied and anomalous Hall effect, inherent to ferromagnetic materials, has been observed. Both normal and anomalous Hall coefficients have been calculated from experimental data, as well as hole densities. Activation energy of impurity level has been estimated.
Resumo:
In der Leistungselektronik spielt die Kenntnis des Wärmevrhaltens einer Platine eine sehr große Rolle. Die immer größeren Leistungsdichten unterstreichen die Wichtigkeit des Kenntnisses des Wärmeverhaltens. In der Platine funktionieren die Leistungskomponenten und Kupferlagen die große Ströme tragen als Leistungsquellen. Das Isolationsmaterial zwischen den Kupferlagen limitiert die maximale Temperatur der Platine. Dieses bringt eine Grentzung für den maximalen Strom der durch die Platine geführt werden kann. In dieser Arbeit wurden die maximalen Stromdichten im Worst-Case-Szenario einer Platine untersucht. Dafür wurde eine Testplatine entworfen und für die Testplatine ein thermisches Modell konstruiert. Die Effekte von Kühlung wurden auch untersucht. Die Bestimmtheit des Modells wurde mit Messungen überprüft.
Resumo:
Various strength properties of paper are measured to tell how well it resists breaks in a paper machine or in printing presses. The most often measured properties are dry tensile strength and dry tear strength. However, in many situations where paper breaks, it is not dry. For example, in web breaks after the wet pressing the dry matter content can be around 45%. Thus, wet-web strength is often a more critical paper property than dry strength. Both wet and dry strength properties of the samples were measured with a L&W tensile tester. Originally this device was not designed for the measurement of the wet web tensile strength, thus a new procedure to handle the wet samples was developed. The method was tested with Pine Kraft (never dried). The effect of different strength additives on the wet-web and dry paper tensile strength was studied. The polymers used in this experiment were aqueous solution of a cationic polyamidoamine-epichlorohydrin resin (PAE), cationic hydrophilised polyisocyanate and cationic polyvinylamine (PVAm). From all three used chemicals only Cationic PAE considerably increased the wet web strength. However it was noticed that at constant solids content all chemicals decreased the wet web tensile strength. So, since all chemicals enhanced solid content it can be concluded that they work as drainage aids, not as wet web strength additives. From all chemicals only PVAm increased the dry strength and two other chemicals even decreased the strength. As chemicals were used in strong diluted forms and were injected into the pulp slurry, not on the surface of the papersheets, changes in samples densities did not happen. Also it has to be noted that all these chemicals are mainly used to improve the wet strength after the drying of the web.
Resumo:
The problem of understanding how humans perceive the quality of a reproduced image is of interest to researchers of many fields related to vision science and engineering: optics and material physics, image processing (compression and transfer), printing and media technology, and psychology. A measure for visual quality cannot be defined without ambiguity because it is ultimately the subjective opinion of an “end-user” observing the product. The purpose of this thesis is to devise computational methods to estimate the overall visual quality of prints, i.e. a numerical value that combines all the relevant attributes of the perceived image quality. The problem is limited to consider the perceived quality of printed photographs from the viewpoint of a consumer, and moreover, the study focuses only on digital printing methods, such as inkjet and electrophotography. The main contributions of this thesis are two novel methods to estimate the overall visual quality of prints. In the first method, the quality is computed as a visible difference between the reproduced image and the original digital (reference) image, which is assumed to have an ideal quality. The second method utilises instrumental print quality measures, such as colour densities, measured from printed technical test fields, and connects the instrumental measures to the overall quality via subjective attributes, i.e. attributes that directly contribute to the perceived quality, using a Bayesian network. Both approaches were evaluated and verified with real data, and shown to predict well the subjective evaluation results.
Resumo:
Ruokohelpi soveltuu ympäristöystävällisyyden ja korkean lämpöarvon vuoksi hyvin energiantuotantoon. Fortumin Joensuun voimalaitoksella ruokohelpi on syötetty kattilaan tähän asti pääasiassa pääpolttoaineisiin, turpeeseen tai hakkeeseen seostettuna pieninä energiaosuuksina. Pääpolttoaineisiin verrattuna ruokohelvellä on alhaisempi irto- ja energiatiheys, korkeampi klooripitoisuus ja kattilaa likaavampi tuhka, mikä asettaa rajoitteita sen käytön lisäämiselle voimalaitoksella. Alhaisesta irto- ja energiatiheydestä johtuvan holvautumisen sekä tukoksien lisääntymisen ja Joensuun voimalaitoksen nykyisten kuljettimien kapasiteettiongelmien vuoksi ruokohelven osuuden lisääminen suuremmaksi kuin 5 % polttoaine-energiasisällöstä on riskialtista ja edellyttää täten investointia erilliseen ruokohelven käsittely- ja syöttöjärjestelmään. Yksi vaihtoehto on murskata ruokohelpipaalit joko sähkökäyttöisellä, puolikiinteällä ja nopeakäyntisellä Haybuster H1130 tilt -murskaimella tai kiinteällä ja hidaskäyntisellä Raumaster-murskaimella ja ohjata ruokohelpisilppu joko pitkän mekaanisen kuljettimen ja sen perässä olevien lyhyiden pneumalinjojen tai pelkkien pitkien pneumalinjojen kautta suoraan kattilapesään. Työssä tutkitut investoinnit ovat taloudellisesti sitä kannattavampia mitä enemmän ruokohelpeä voidaan vuositasolla polttaa voimalaitoksella. Ruokohelven käyttömäärää voimalaitoksella kannattanee lisätä kuljetusmatkaa pidentämällä. Investointien valinta ei ole itsestäänselvyys. Nopeakäyntinen murskain on hidaskäyntistä murskainta edullisempi investointi, tosin hidaskäyntisen murskaimen käyttövarmuus on parempi kuin nopeakäyntisen murskaimen. Kattilan käytettävyyden kannalta ruokohelven käytön lisääminen edellyttää kattilan palamistekniikan analysointia laskennallisesti virtausmallinnuksella ennen kuin lopullisia päätöksiä investointien suhteen voidaan tehdä.
Resumo:
In this thesis three experiments with atomic hydrogen (H) at low temperatures T<1 K are presented. Experiments were carried out with two- (2D) and three-dimensional (3D) H gas, and with H atoms trapped in solid H2 matrix. The main focus of this work is on interatomic interactions, which have certain specific features in these three systems considered. A common feature is the very high density of atomic hydrogen, the systems are close to quantum degeneracy. Short range interactions in collisions between atoms are important in gaseous H. The system of H in H2 differ dramatically because atoms remain fixed in the H2 lattice and properties are governed by long-range interactions with the solid matrix and with H atoms. The main tools in our studies were the methods of magnetic resonance, with electron spin resonance (ESR) at 128 GHz being used as the principal detection method. For the first time in experiments with H in high magnetic fields and at low temperatures we combined ESR and NMR to perform electron-nuclear double resonance (ENDOR) as well as coherent two-photon spectroscopy. This allowed to distinguish between different types of interactions in the magnetic resonance spectra. Experiments with 2D H gas utilized the thermal compression method in homogeneous magnetic field, developed in our laboratory. In this work methods were developed for direct studies of 3D H at high density, and for creating high density samples of H in H2. We measured magnetic resonance line shifts due to collisions in the 2D and 3D H gases. First we observed that the cold collision shift in 2D H gas composed of atoms in a single hyperfine state is much smaller than predicted by the mean-field theory. This motivated us to carry out similar experiments with 3D H. In 3D H the cold collision shift was found to be an order of magnitude smaller for atoms in a single hyperfine state than that for a mixture of atoms in two different hyperfine states. The collisional shifts were found to be in fair agreement with the theory, which takes into account symmetrization of the wave functions of the colliding atoms. The origin of the small shift in the 2D H composed of single hyperfine state atoms is not yet understood. The measurement of the shift in 3D H provides experimental determination for the difference of the scattering lengths of ground state atoms. The experiment with H atoms captured in H2 matrix at temperatures below 1 K originated from our work with H gas. We found out that samples of H in H2 were formed during recombination of gas phase H, enabling sample preparation at temperatures below 0.5 K. Alternatively, we created the samples by electron impact dissociation of H2 molecules in situ in the solid. By the latter method we reached highest densities of H atoms reported so far, 3.5(5)x1019 cm-3. The H atoms were found to be stable for weeks at temperatures below 0.5 K. The observation of dipolar interaction effects provides a verification for the density measurement. Our results point to two different sites for H atoms in H2 lattice. The steady-state nuclear polarizations of the atoms were found to be non-thermal. The possibility for further increase of the impurity H density is considered. At higher densities and lower temperatures it might be possible to observe phenomena related to quantum degeneracy in solid.