On the Application of Beam on Elastic Foundation Theory to the Analysis of Stiffened Plate Strips

The main objective of this thesis is to show that plate strips subjected to transverse line loads can be analysed by using the beam on elastic foundation (BEF) approach. It is shown that the elastic behaviour of both the centre line section of a semi infinite plate supported along two edges, and the free edge of a cantilever plate strip can be accurately predicted by calculations based on the two parameter BEF theory. The transverse bending stiffness of the plate strip forms the foundation. The foundation modulus is shown, mathematically and physically, to be the zero order term of the fourth order differential equation governing the behaviour of BEF, whereas the torsion rigidity of the plate acts like pre tension in the second order term. Direct equivalence is obtained for harmonic line loading by comparing the differential equations of Levy's method (a simply supported plate) with the BEF method. By equating the second and zero order terms of the semi infinite BEF model for each harmonic component, two parameters are obtained for a simply supported plate of width B: the characteristic length, 1/ λ, and the normalized sum, n, being the effect of axial loading and stiffening resulting from the torsion stiffness, nlin. This procedure gives the following result for the first mode when a uniaxial stress field was assumed (ν = 0): 1/λ = √2B/π and nlin = 1. For constant line loading, which is the superimposition of harmonic components, slightly differing foundation parameters are obtained when the maximum deflection and bending moment values of the theoretical plate, with v = 0, and BEF analysis solutions are equated: 1 /λ= 1.47B/π and nlin. = 0.59 for a simply supported plate; and 1/λ = 0.99B/π and nlin = 0.25 for a fixed plate. The BEF parameters of the plate strip with a free edge are determined based solely on finite element analysis (FEA) results: 1/λ = 1.29B/π and nlin. = 0.65, where B is the double width of the cantilever plate strip. The stress biaxial, v > 0, is shown not to affect the values of the BEF parameters significantly the result of the geometric nonlinearity caused by in plane, axial and biaxial loading is studied theoretically by comparing the differential equations of Levy's method with the BEF approach. The BEF model is generalised to take into account the elastic rotation stiffness of the longitudinal edges. Finally, formulae are presented that take into account the effect of Poisson's ratio, and geometric non linearity, on bending behaviour resulting from axial and transverse inplane loading. It is also shown that the BEF parameters of the semi infinite model are valid for linear elastic analysis of a plate strip of finite length. The BEF model was verified by applying it to the analysis of bending stresses caused by misalignments in a laboratory test panel. In summary, it can be concluded that the advantages of the BEF theory are that it is a simple tool, and that it is accurate enough for specific stress analysis of semi infinite and finite plate bending problems.

Learning Robot Motions from Visual Sensing

Learning from demonstration becomes increasingly popular as an efficient way of robot programming. Not only a scientific interest acts as an inspiration in this case but also the possibility of producing the machines that would find application in different areas of life: robots helping with daily routine at home, high performance automata in industries or friendly toys for children. One way to teach a robot to fulfill complex tasks is to start with simple training exercises, combining them to form more difficult behavior. The objective of the Master’s thesis work was to study robot programming with visual input. Dynamic movement primitives (DMPs) were chosen as a tool for motion learning and generation. Assuming a movement to be a spring system influenced by an external force, making this system move, DMPs represent the motion as a set of non-linear differential equations. During the experiments the properties of DMP, such as temporal and spacial invariance, were examined. The effect of the DMP parameters, including spring coefficient, damping factor, temporal scaling, on the trajectory generated were studied.

Uusiutuvat kvasikonformikuvaukset

Kirjallisuusarvostelu

Determining vehicle drivetrain dynamics using system identification

Target of this book is to propose an approach for modelling drivetrain dynamics in order to design further a vibration control system of a hybrid bus. In this thesis two approaches are examined and compared. First model is obtained by theoretical means: drivetrain is represented as a system of rotating masses, which motion is described with differential equations. Second model is obtained using system identification method: mathematical description of the dynamic behavior of a system is formed based on measured input (torque) and output (speed) data. Then two models are compared and an optimal approach is suggested.

Neopentyyliglykolin ja propionihapon välisen esteröintireaktion kinetiikka

Glykolien esterit ovat haluttuja pintareaktiivisia aineita. Niitä voidaan valmistaa esteröintireaktiolla karboksyylihappojen kanssa katalyytin läsnä ollessa, jolloin toivottu reaktiotuote on yleensä muodostuva monoesteri. Monoesterin saannon lisäämiseksi reaktiossa muodostuvaa vettä voidaan poistaa jatkuvasti reaktiosta. Reaktion tasapainotilan tutkiminen on kuitenkin tärkeää, jotta reaktion kinetiikka tunnettaisiin mahdollisimman hyvin. Tällöin reaktiotuotteita ei poisteta reaktioseoksesta reaktion aikana. Glykolit esteröityvät happojen kanssa kahdessa vaiheessa. Ensimmäisessä vaiheessa muodostuu monoesteriä ja vettä ja toisessa vaiheessa diesteriä ja vettä. Kokeiden perusteella ensimmäinen vaihe on selvästi toista vaihetta nopeampi reaktio. Kirjallisuudessa on esitetty myös kaksi sivureaktiota, transesteröityminen ja disproportionaatio. Reaktion kinetiikka voidaan kuvata ilman näitä pieniä sivureaktiota, mutta täydellisen kuvaamisen vuoksi on ne myös otettava huomioon. Reaktion kinetiikan tutkimiseksi suoritettiin viisi laboratoriokoetta eri lämpötiloissa neopentyyliglykolilla ja propionihapolla homogeenisen para-tolueenisulfonihapon toimiessa katalyyttina. Lähtöaineiden ja tuotteiden konsentraatioita seurattiin ajan funktiona ja saatujen tulosten perusteella sovitettiin reaktiomekanismin differentiaaliyhtälöiden reaktionopeusvakiot. Nopeusvakioiden lämpötilariippuvuutta tutkittiin Arrheniuksen yhtälön avulla. Lisäksi määritettiin tasapainovakiot kullekin osareaktiolle.

Modelling the exothermic heat and the demand of cooling in paper and pulp industry biological wastewater treatment

This master thesis presents a study on the requisite cooling of an activated sludge process in paper and pulp industry. The energy consumption of paper and pulp industry and it’s wastewater treatment plant in particular is relatively high. It is therefore useful to understand the wastewater treatment process of such industries. The activated sludge process is a biological mechanism which degrades carbonaceous compounds that are present in waste. The modified activated sludge model constructed here aims to imitate the bio-kinetics of an activated sludge process. However, due to the complicated non-linear behavior of the biological process, modelling this system is laborious and intriguing. We attempt to find a system solution first using steady-state modelling of Activated Sludge Model number 1 (ASM1), approached by Euler’s method and an ordinary differential equation solver. Furthermore, an enthalpy study of paper and pulp industry’s vital pollutants was carried out and applied to revise the temperature shift over a period of time to formulate the operation of cooling water. This finding will lead to a forecast of the plant process execution in a cost-effective manner and management of effluent efficiency. The final stage of the thesis was achieved by optimizing the steady state of ASM1.