Simulations of 3D Stripixel Detectors

Large Hadron Collider (LHC) is the main particle accelerator at CERN. LHC is created with main goal to search elementary particles and help science investigate our universe. Radiation in LHC is caused by charged particles circular acceleration, therefore detectors tracing particles in existed severe conditions during the experiments must be radiation tolerant. Moreover, further upgrade of luminosity (up to 1035 cm-2s-1) requires development of particle detector’s structure. This work is dedicated to show the new type 3D stripixel detector with serious structural improvement. The new type of radiation-hard detector has a three-dimensional (3D) array of the p+ and n+ electrodes that penetrate into the detector bulk. The electrons and holes are then collected at oppositely biased electrodes. Proposed 3D stripixel detector demonstrates that full depletion voltage is lower that that for planar detectors. Low depletion voltage is one of the main advantages because only depleted part of the device is active are. Because of small spacing between electrodes, charge collection distances are smaller which results in high speed of the detector’s response. In this work is also briefly discussed dual-column type detectors, meaning consisting both n+ and p+ type columnar electrodes in its structure, and was declared that dual-column detectors show better electric filed distribution then single sided radiation detectors. The dead space or in other words low electric field region in significantly suppressed. Simulations were carried out by using Atlas device simulation software. As a simulation results in this work are represented the electric field distribution under different bias voltages.

Korkeasti kuormitetun soodakattilan likaantumisen ja päästöjen vähentäminen

Tässä työssä perehdytään korkeasti kuormitettujen soodakattiloiden tyypillisiin ongelmiin. Ongelmia ovat likaantuminen ja tukkeutuminen sekä liialliset päästöt. Työn teoriaosassa esitetään taustat likaantumiselle ja päästöjen muodostumiselle. Molemmat johtuvat suurelta osin tulipesän huonosta toiminnasta. Soodakattilan ilmajärjestelmä ja mustalipeän ruiskutus vaikuttavat tulipesän toimintaan. Usein tulipesän toimintaa voidaan parantaa ilmajärjestelmän ja lipeänruiskutuksen säätöjä muuttamalla. Suurempi muutos tulipesän toimintaan saadaan uusimalla perinteinen sekundääri-ilmajärjestelmä vertikaali-ilmajärjestelmäksi. Nykyaikainen vertikaali-ilmajärjestelmä sekoittaa savukaasut tehokkaasti ja saa aikaan tasaisemman virtauksen tulipesään. Myös mustalipeän korkea kloori- ja kaliumpitoisuus voivat aiheuttaa lämpöpintojen likaantumista. Oikea nuohointen sijainti on tärkeä tekijä kattilan puhtaana pysymisen kannalta. Työn kokeellisessa osassa selvitetään, kuinka erään eukalyptussellutehtaan korkeasti kuormitetun soodakattilan käytettävyyttä voidaan parantaa ja kapasiteettia nostaa soodakattilan toimintaa virittämällä. Kattilan nykyinen ajomalli ja ongelmat selvitettiin. Tulipesän toimintaa testattiin muuttamalla ilmajakoa primääri-, sekundääri- ja tertiääri-ilman välillä ja muuttamalla sekundääri-ilman syöttöä tulipesään. Testien ja kerätyn tiedon perusteella voitiin päätellä, miten soodakattilaa kannattaa modernisoida kapasiteetin nostamiseksi ja käytettävyyden parantamiseksi. Usein tulipesän toimintaa ja käytettävyyttä voidaan parantaa paljon jo pienilläkin muutostöillä. Kapasiteetin nostaminen vaatii tavallisesti suuremman investoinnin ja pidennetyn vuosihuoltoseisokin.

Feasibility of the use of recycled nutrients in fast growing pulpwood production

The application of pulp and paper mill (PPM) sludge in agriculture and forestry has been acknowledged as soil amendments and a plant nutrient source. The main objectives of this study were to evaluate the total cost of the use of recycled nutrients from PPM sludge in fast growing pulpwood production, and the financial profitability of fast growing pulpwood production with the use of these recycled nutrients. The investment and production costs of fast growing pulpwood plantation were directly acquired from a previous research, while the other data was compiled through different studies. The total cost of the use of PPM sludge was evaluated based on assumed factors. Discounted cash flow method was used to evaluate the financial profitability, using NPV and IRR as indicators. The results of estimated sludge nutrient contents were 16.2 g N, 2.9 g P, and 2.4 g K kg-1 of dry sludge. The sludge application rate was estimated at 1.36 Mg/ha in the first year. The total cost of the use of PPM sludge involved transport and spreading cost of US$49.15/dry ton. The fertilization cost applied in the financial model was designed in 3 different options and their results were as follows: option (1) was taken directly from the reference research (US$97/ha); option (2) was the use of sludge alone (US$66.75/ha); and option (3) was the use of sludge and TSP fertilizer (US$83.80/ha). The average NPV without discounting was US$248,180 while the IRRs ranged between approximately 3-4% with an average of 3.63%. Although option (2) and (3) contributed to higher IRRs compared to option (1), this increase was still not significant as the IRR was not sensitive to the total fertilization cost. The advantages are that this practice can be performed at a lower cost and the application rate can be still increased if necessary. It is better for forest plantations compared to agriculture and consequently supports reforestation program. In addition, it can be similarly applied in wood biomass production. A disadvantage is that the IRRs were not very favorable compared to the criterion of 11%. The sludge high in C:N ratio can cause nitrogen immobilization, and regulatory concerns may restrict and complicate the use of sludge landspreading and contribute to additional costs and processes.

Effects of Fin Parameters on Gas-Side Heat Transfer Performance of H-Type Finned Tube Bundle in a Waste Heat Recovery Boiler

Alfa Laval Aalborg Oy designs and manufactures waste heat recovery systems utilizing extended surfaces. The waste heat recovery boiler considered in this thesis is a water-tube boiler where exhaust gas is used as the convective heat transfer medium and water or steam flowing inside the tubes is subject to cross-flow. This thesis aims to contribute to the design of waste heat recovery boiler unit by developing a numerical model of the H-type finned tube bundle currently used by Alfa Laval Aalborg Oy to evaluate the gas-side heat transfer performance. The main objective is to identify weaknesses and potential areas of development in the current H-type finned tube design. In addition, numerical simulations for a total of 15 cases with varying geometric parameters are conducted to investigate the heat transfer and pressure drop performance dependent on H-type fin geometry. The investigated geometric parameters include fin width and height, fin spacing, and fin thickness. Comparison between single and double tube type configuration is also conducted. Based on the simulation results, the local heat transfer and flow behaviour of the H-type finned tube is presented including boundary layer development between the fins, the formation of recirculation zone behind the tubes, and the local variations of flow velocity and temperature within the tube bundle and on the fin surface. Moreover, an evaluation of the effects of various fin parameters on heat transfer and pressure drop performance of H-type finned tube bundle has been provided. It was concluded that from the studied parameters fin spacing and fin width had the most significant effect on tube bundle performance and the effect of fin thickness was the least important. Furthermore, the results suggested that the heat transfer performance would increase due to enhanced turbulence if the current double tube configuration is replaced with single tube configuration, but further investigation and experimental measurements are required in order to validate the results.