Implementing theLean Manufacturing System

Tuottavuuden ja tehokkuuden parantaminen on keskeisimpiä menestystekijöitä glo-baaleilla markkinoilla. Yksi kehittämisen toimintamalli on lean manufacturing -ajattelutapa, joka perustuu imuohjaukseen. Sen lähtökohtana on asiakasarvo ja keskit-tyminen arvoa lisäävien toimintojen maksimointiin. Tutkimuksen tavoitteena oli parantaa Strömfors Electric Oy:n materiaalivirtauksia yhdellä tuotantolinjalla. Projektin oli tarkoitus olla pilotti lean-implementointiin koko tehtaalla. Projektissa otettiin käyttöön kanban-imuohjausjärjestelmä, jota varten teh-tiin analyysejä ja laskelmia arvovirtoihin, varastoihin ja ohjaukseen. Lean-ajattelutapaan ja -työkaluihin perustuvaa kirjallisuutta käytettiin pohjatietona pilotti-projektissa sekätulevien kehitysprojektien suunnittelussa. Pilottiprojektin tuloksena materiaalinohjaus tehostui ja keskeneräisen tuotannon va-rasto tasoittui käyttötarpeen mukaiseksi. Työntekijät ja työnjohtajat tutustuivat leanin perusteisiin osallistuessaan pilottiprojektiin. Pidemmän aikavälin suunnitelmissa ontoimitusvarmuuden ja laadun parantuminen ensin pilottiprojektia koskevalla linjalla ja myöhemmin koko tehtaalla imuohjauksen kokonaisvaltaisen käyttöönoton myötä.

Field Sales Management Control: Towards a Multi-Level Theory

The purpose of this dissertation is to increase the understanding and knowledge of field sales management control systems (i.e. sales managers monitoring, directing, evaluating and rewarding activities) and their potential consequences on salespeople. This topic is important because research conducted in the past has indicated that the choice of control system type can on the other hand have desirable consequences, such as high levels of motivation and performance, and on the other hand leadto harmful unintended consequences, such as opportunistic or unethical behaviors. Despite the fact that marketing and sales management control systems have been under rigorous research for over two decades, it still is at a very early stage of development, and several inconsistencies can be found in the research results. This dissertation argues that these inconsistencies are mainly derived from misspecification of the level of analysis in the past research. These different levels of analysis (i.e. strategic, tactical, and operational levels) involve very different decision-making situations regarding the control and motivation of sales force, which should be taken into consideration when conceptualizing the control. Moreover, the study of salesperson consequences of a field sales management control system is actually a cross-level phenomenon, which means that at least two levels of analysis are simultaneously involved. The results of this dissertation confirm the need to re-conceptualize the field sales management control system concept. It provides empirical evidence for the assertion that control should be conceptualized with more details atthe tactical/operational level of analysis than at the strategic levelof analysis. Moreover, the results show that some controls are more efficiently communicated to field salespeople than others. It is proposed that this difference is due to different purposes of control; some controls aredesigned for influencing salespersons' behavior (aim at motivating) whereas some controls are designed to aid decision-making (aim at providing information). According to the empirical results of this dissertation, the both types of controls have an impact to the sales force, but this impactis not as strong as expected. The results obtained in this dissertation shed some light to the nature of field sales management control systems, and their consequences on salespeopl

Converter-flux-based current control of voltage source PWM rectifiers - analysis and implementation

Pulsewidth-modulated (PWM) rectifier technology is increasingly used in industrial applications like variable-speed motor drives, since it offers several desired features such as sinusoidal input currents, controllable power factor, bidirectional power flow and high quality DC output voltage. To achieve these features,however, an effective control system with fast and accurate current and DC voltage responses is required. From various control strategies proposed to meet these control objectives, in most cases the commonly known principle of the synchronous-frame current vector control along with some space-vector PWM scheme have been applied. Recently, however, new control approaches analogous to the well-established direct torque control (DTC) method for electrical machines have also emerged to implement a high-performance PWM rectifier. In this thesis the concepts of classical synchronous-frame current control and DTC-based PWM rectifier control are combined and a new converter-flux-based current control (CFCC) scheme is introduced. To achieve sufficient dynamic performance and to ensure a stable operation, the proposed control system is thoroughly analysed and simple rules for the controller design are suggested. Special attention is paid to the estimationof the converter flux, which is the key element of converter-flux-based control. Discrete-time implementation is also discussed. Line-voltage-sensorless reactive reactive power control methods for the L- and LCL-type line filters are presented. For the L-filter an open-loop control law for the d-axis current referenceis proposed. In the case of the LCL-filter the combined open-loop control and feedback control is proposed. The influence of the erroneous filter parameter estimates on the accuracy of the developed control schemes is also discussed. A newzero vector selection rule for suppressing the zero-sequence current in parallel-connected PWM rectifiers is proposed. With this method a truly standalone and independent control of the converter units is allowed and traditional transformer isolation and synchronised-control-based solutions are avoided. The implementation requires only one additional current sensor. The proposed schemes are evaluated by the simulations and laboratory experiments. A satisfactory performance and good agreement between the theory and practice are demonstrated.

Production Control Principles in Printed Wiring Board Fabrication

Työn tavoitteena oli kuvata piirilevyvalmistaja Aspocomp Oy:n Espoon tehtaan tämän hetkinen tuotannonohjausperiaate ja tunnistaa siinä esiintyvät puutteet sekä kehittää vaihtoehtoinen tuotannonohjausperiaate piirilevyvalmistukseen. Vaihtoehtoisen ohjausperiaatteen lähtökohtana oli tuotannonohjauksen sopeuttaminen vaativaan ja jatkuvasti muuttuvaan liiketoimintaympäristöön. Työn teoreettinen osa keskittyi tuotannonohjauksen eri lähestymistapoihin. Kirjallisuuskatsauksessa esitetään eri tuotannonohjausperiaatteiden keskeiset sisällöt, jotka muodostavat rungon toimivalle tuotannonohjauskäytännölle. Työn kokeellinen osa keskittyi Espoon piirilevytehtaan tuotannonohjausperiaatteen selvittämiseen. Espoon piirilevytehtaan nykyisessä tuotannonohjausperiaatteessa havaittujen ongelmakohtien ja liiketoimintaympäristön vaatimusten perusteella kehitettiin vaihtoehtoinen tuotannonohjaustapa. Vaihtoehtoisen tuotannonohjaustavan päämääränä oli läpimenoajan lyhentäminen sekä tuotannon parempi hallittavuus. Vaihtoehtoinen toimintamalli tavoitteiden saavuttamiseksi perustuu pullonkaulateoriaan, jossa keskeisin muutos nykyiseen toimintamalliin oli puolivalmisteiden varastointi toimitusajan lyhentämiseksi sekä tuotantovolyymin heilahdusten vaikutusten vähentämiseksi. Työn kokeellisessa osassa ilmeni, että kysynnän muutokset ja kapasiteetin suunnittelun puute aiheuttivat ongelmia piirilevytehtaan tuotannonohjauksessa.

Robots and robotic systems for the electronics and telecommunication industry

Tämä diplomityö tutkii elektroniikka- ja telekommunikaatioteollisuutta sekä siihen läheisesti liittyviä robotteja ja robottijärjestelmiä. Tavoitteena on määrittää E&T-teollisuuden prosesseihin soveltuvien robottien testausmenetelmä. Tavoitteena on myös selvittää kahden ABB:n robotin soveltuvuutta E&T-teollisuuden tarpeisiin. Muutamia systemaattisia valmistusjärjestelmien suunnitteluun soveltuvia menetelmiä ja apuvälineitä on myös käsitelty. Alussa työ keskittyy elektroniikka- ja telekommunikaatioteollisuuden nykytilan tutkimiseen sekä siellä vallitsevien ja ennustettujen trendien kartoitukseen. Kohdat “Collaborative manufacturing” ja E&T-teollisuuden valmistusjärjestelmille asettamat vaatimukset käydään yksityiskohtaisesti läpi. Tutkimuksen pääkohteina ovat robotit, erityisesti ABB:n IRB 140 ja IRB 340 sekä robottien testausmenetelmän määrittäminen. Työssä käydään läpi IRB 340:llä suoritetut testit, jotka tehtiin sekä konenäköjärjestelmää apuna käyttäen että ilman. Myös TTKK:lla suoritetut robottitestit on käyty läpi. Robottien testituloksia on analysoitu ja vertailtu muihin robotteihin. Testausmenetelmät perustuvat ISO 9283 standardiin. Viimeinen osa työstä esittelee robottijärjestelmien systemaattiseen suunnitteluun soveltuvia menetelmiä ja apuvälineitä. Esillä ovat mm. Modular function deployment (MFD) ja The system design method (SDM).

On the Analysis and Control of a Linear Synchronous Servomotor with a Flexible Load

Industry's growing need for higher productivity is placing new demands on mechanisms connected with electrical motors, because these can easily lead to vibration problems due to fast dynamics. Furthermore, the nonlinear effects caused by a motor frequently reduce servo stability, which diminishes the controller's ability to predict and maintain speed. Hence, the flexibility of a mechanism and its control has become an important area of research. The basic approach in control system engineering is to assume that the mechanism connected to a motor is rigid, so that vibrations in the tool mechanism, reel, gripper or any apparatus connected to the motor are not taken into account. This might reduce the ability of the machine system to carry out its assignment and shorten the lifetime of the equipment. Nonetheless, it is usually more important to know how the mechanism, or in other words the load on the motor, behaves. A nonlinear load control method for a permanent magnet linear synchronous motor is developed and implemented in the thesis. The purpose of the controller is to track a flexible load to the desired velocity reference as fast as possible and without awkward oscillations. The control method is based on an adaptive backstepping algorithm with its stability ensured by the Lyapunov stability theorem. As a reference controller for the backstepping method, a hybrid neural controller is introduced in which the linear motor itself is controlled by a conventional PI velocity controller and the vibration of the associated flexible mechanism is suppressed from an outer control loop using a compensation signal from a multilayer perceptron network. To avoid the local minimum problem entailed in neural networks, the initial weights are searched for offline by means of a differential evolution algorithm. The states of a mechanical system for controllers are estimated using the Kalman filter. The theoretical results obtained from the control design are validated with the lumped mass model for a mechanism. Generalization of the mechanism allows the methods derived here to be widely implemented in machine automation. The control algorithms are first designed in a specially introduced nonlinear simulation model and then implemented in the physical linear motor using a DSP (Digital Signal Processor) application. The measurements prove that both controllers are capable of suppressing vibration, but that the backstepping method is superior to others due to its accuracy of response and stability properties.

System Investigation for Hybrid Electric Vehicle

A hybrid electric vehicle is a fast-growing concept in the field of vehicle industry. Nowadays two global problems make manufactures to develop such systems. These problems are: the growing cost of a fuel and environmental pollution. Also development of controlled electric drive with high control accuracy and reliability allows improving of vehicle drive characteristics. The objective of this Diploma Thesis is to investigate the possibilities of electrical drive application for new principle of parallel hybrid vehicle system. Electric motor calculations, selection of most suitable control system and other calculations are needed. This work is not final work for such topic. Further investigation with more precise calculations, modeling, measurements and cost calculations are needed to answer the question if such system is efficient.

The effects of real time control of welding parameters on weld quality in plasma arc keyhole welding

Joints intended for welding frequently show variations in geometry and position, for which it is unfortunately not possible to apply a single set of operating parameters to ensure constant quality. The cause of this difficulty lies in a number of factors, including inaccurate joint preparation and joint fit up, tack welds, as well as thermal distortion of the workpiece. In plasma arc keyhole welding of butt joints, deviations in the gap width may cause weld defects such as an incomplete weld bead, excessive penetration and burn through. Manual adjustment of welding parameters to compensate for variations in the gap width is very difficult, and unsatisfactory weld quality is often obtained. In this study a control system for plasma arc keyhole welding has been developed and used to study the effects of the real time control of welding parameters on gap tolerance during welding of austenitic stainless steel AISI 304L. The welding tests demonstrated the beneficial effect of real time control on weld quality. Compared with welding using constant parameters, the maximum tolerable gap width with an acceptable weld quality was 47% higher when using the real time controlled parameters for a plate thickness of 5 mm. In addition, burn through occurred with significantly larger gap widths when parameters were controlled in real time. Increased gap tolerance enables joints to be prepared and fit up less accurately, saving time and preparation costs for welding. In addition to the control system, a novel technique for back face monitoring is described in this study. The test results showed that the technique could be successfully applied for penetration monitoring when welding non magnetic materials. The results also imply that it is possible to measure the dimensions of the plasma efflux or weld root, and use this information in a feedback control system and, thus, maintain the required weld quality.

The Detector Control Systems for the CMS Resistive Plate Chamber at LHC

The RPC Detector Control System (RCS) is the main subject of this PhD work. The project, involving the Lappeenranta University of Technology, the Warsaw University and INFN of Naples, is aimed to integrate the different subsystems for the RPC detector and its trigger chain in order to develop a common framework to control and monitoring the different parts. In this project, I have been strongly involved during the last three years on the hardware and software development, construction and commissioning as main responsible and coordinator. The CMS Resistive Plate Chambers (RPC) system consists of 912 double-gap chambers at its start-up in middle of 2008. A continuous control and monitoring of the detector, the trigger and all the ancillary sub-systems (high voltages, low voltages, environmental, gas, and cooling), is required to achieve the operational stability and reliability of a so large and complex detector and trigger system. Role of the RPC Detector Control System is to monitor the detector conditions and performance, control and monitor all subsystems related to RPC and their electronics and store all the information in a dedicated database, called Condition DB. Therefore the RPC DCS system has to assure the safe and correct operation of the sub-detectors during all CMS life time (more than 10 year), detect abnormal and harmful situations and take protective and automatic actions to minimize consequential damages. The analysis of the requirements and project challenges, the architecture design and its development as well as the calibration and commissioning phases represent themain tasks of the work developed for this PhD thesis. Different technologies, middleware and solutions has been studied and adopted in the design and development of the different components and a big challenging consisted in the integration of these different parts each other and in the general CMS control system and data acquisition framework. Therefore, the RCS installation and commissioning phase as well as its performance and the first results, obtained during the last three years CMS cosmic runs, will be

Tiedon hajautus johtamisjärjestelmässä ja DDS-teknologia

Verkostokeskeisessä sodankäynnissä tietojärjestelmien suurimpana haasteena on oikean tiedon hajauttaminen oikeaan paikkaan ja aikaan. Tietojärjestelmissä esitettävän ilmatilannekuvan tulee vastata reaalimaailman tilannetta parhaalla mahdollisella tavalla. Ilmatorjunnassa reaaliaikaisuus nousee erityisen suureen rooliin nopeasti liikkuvien kohteiden takia. Tämä diplomityö on tehty Insta DefSec Oy:ssä liittyen johtamisjärjestelmän uudistamishankkeeseen. Työn vaatimuksina olivat standardeihin perustuvat ratkaisut, joista keskeisimmäksi nousi Data Distribution Service -standardi (DDS) ja sen hyödyntäminen osana johtamisjärjestelmän tiedon hajautusta. Työssä esitellään johtamisjärjestelmien tiedon hajautukseen liittyviä haasteita sekä paikallisessa että maantieteellisesti hajautetussa toimintaympäristössä. Työssä toteutettiin liityntäohjelmisto nykyisen ja uuden johtamisjärjestelmän välille. Liityntäohjelmiston tehtävänä on tuottaa reaaliaikaista ilmatilannekuvaa nykyisestä johtamisjärjestelmästä uuteen johtamisjärjestelmään. DDS-standardin toteuttavana välikerrosarkkitehtuurina käytettiin OpenSplice DDS -tuotetta. Valittu teknologia tarjoaa edistykselliset julkaisija–tilaaja-mallin mukaiset menetelmät tiedon reaaliaikaiseen hajauttamiseen. DDS:n arkkitehtuuri ja palvelun laadun mekanismit mahdollistavat tiedon hajautuksen sodanajan johtamisjärjestelmille.

Simulating the performance of paper machine control

The topic of this thesis is the simulation of a combination of several control and data assimilation methods, meant to be used for controlling the quality of paper in a paper machine. Paper making is a very complex process and the information obtained from the web is sparse. A paper web scanner can only measure a zig zag path on the web. An assimilation method is needed to process estimates for Machine Direction (MD) and Cross Direction (CD) profiles of the web. Quality control is based on these measurements. There is an increasing need for intelligent methods to assist in data assimilation. The target of this thesis is to study how such intelligent assimilation methods are affecting paper web quality. This work is based on a paper web simulator, which has been developed in the TEKES funded MASI NoTes project. The simulator is a valuable tool in comparing different assimilation methods. The thesis contains the comparison of four different assimilation methods. These data assimilation methods are a first order Bayesian model estimator, an ARMA model based on a higher order Bayesian estimator, a Fourier transform based Kalman filter estimator and a simple block estimator. The last one can be considered to be close to current operational methods. From these methods Bayesian, ARMA and Kalman all seem to have advantages over the commercial one. The Kalman and ARMA estimators seems to be best in overall performance.

Hammashihnajohdeakseleiden liikkeiden synkronointi

Nykyisessä valmistusteollisuudessa erilaisten robottien ja automatisoitujen tuotantovaiheiden rooli on erittäin merkittävä. Tarkasti suunnitellut liikkeet ja toimintavaiheet voidaan nykyisillä järjestelmillä ajoittaa tarkasti toisiinsa nähden, jolloin erilaisten virhetilanteidenkin sattuessa järjestelmä pystyy toimimaan tilanteen edellyttämällä tavalla. Automatisoinnin etuna on myös tuotannon muokkaaminen erilaisten tuotteiden valmistamiseen pienillä muutoksilla, jolloin tuotantokustannukset pysyvät matalina myös pienten valmistuserien tapauksissa. Usean akselin laitteissa eli niin sanotuissa moniakselikäytöissä laitteen toimintatarkkuus riippuu jokaisen liikeakselin tarkkuudesta. Liikkeenohjauksessa on perinteisesti ollut käytössä myötäkytketty paikkakaskadi, jonka virityksessä otetaan huomioon akselilla olevat erilaiset dynaamiset tilat ja käytettävät referenssit. Monissa nykyisissä hajautetuissa järjestelmissä eli moniakselikäytöissä, joissa jokaiselle akselille on oma ohjauslaite, ei yksittäisen akselin paikkavirhettä huomioida muiden akseleiden ohjauksessa. Työssä tutkitaan erilaisia moniakselijärjestelmien ohjausmenetelmiä ja myötäkytketyn paikkakaskadin toimintaa moniakselikäytössä pyritään parantamaan tuomalla paikkasäätimen rinnalle toinen säädin, jonka tulona on akseleiden välinen paikkaero.

Modeling and Control of the Power Conversion Unit in a Solid Oxide Fuel Cell Environment

In this doctoral thesis, a power conversion unit for a 10 kWsolid oxide fuel cell is modeled, and a suitable control system is designed. The need for research was identified based on an observation that there was no information available about the characteristics of the solid oxide fuel cell from the perspective of power electronics and the control system, and suitable control methods had not previously been studied in the literature. In addition, because of the digital implementation of the control system, the inherent characteristics of the digital system had to be taken into account in the characteristics of the solid oxide fuel cell (SOFC). The characteristics of the solid oxide fuel cell as well the methods for the modeling and control of the DC/DC converter and the grid converter are studied by a literature survey. Based on the survey, the characteristics of the SOFC as an electrical power source are identified, and a solution to the interfacing of the SOFC in distributed generation is proposed. A mathematical model of the power conversion unit is provided, and the control design for the DC/DC converter and the grid converter is made based on the proposed interfacing solution. The limit cycling phenomenon is identified as a source of low-frequency current ripple, which is found to be insignificant when connected to a grid-tied converter. A method to mitigate a second harmonic originating from the grid interface is proposed, and practical considerations of the operation with the solid oxide fuel cell plant are presented. At the theoretical level, the thesis discusses and summarizes the methods to successfully derive a model for a DC/DC converter, a grid converter, and a power conversion unit. The results of this doctoral thesis can also be used in other applications, and the models and methods can be adopted to similar applications such as photovoltaic systems. When comparing the results with the objectives of the doctoral thesis, we may conclude that the objectives set for the work are met. In this doctoral thesis, theoretical and practical guidelines are presented for the successful control design to connect a SOFC-based distributed generation plant to the utility grid.

One chip solution for low-cost active magnetic bearing system

In this work the implementation of the active magnetic bearing control system in a single FPGA is studied. Requirements for the full magnetic bearing control system are reviewed. Different control methods for active magnetic bearings are described shortly. Flux and the current base controllers are implemented in a FPGA. Suitability of the con-trollers for a low-cost magnetic bearing application is studied. Floating-point arithmetic’s are used in the controllers to ease designing burden and improve calculation precision. Per-formance of the flux controller is verified with simulations.

Venäjän sotilasreformi : asevoimien uusi ilme

Tässä työpaperissa Venäjän sotilasreformin tarkastelu painottuu maavoimiin. Muista puolustushaaroista käsitellään lyhyesti meri- ja ilmavoimia. Lisäksi käsitellään koulutus, reservi ja mobilisaatio, johtaminen, toiminnan ulkoistaminen ja sosiaaliset kysymykset sekä asevoimien varustaminen. Julkaisun lähdemateriaali on lähes kokonaan venäjänkielistä. Sen avulla esitetään venäläisten omat niin myönteiset kuin kriittiset näkemykset koskien Venäjän asevoimien sotilasreformia, uutta ilmettä. Venäjänkielisistä termeistä käytetään mahdollisimman vastaavaa tai kuvaavaa suomenkielistä ilmaisua.