Size Effect and Notch Size Effect in Metal Fatigue

It is a well known phenomenon that the constant amplitude fatigue limit of a large component is lower than the fatigue limit of a small specimen made of the same material. In notched components the opposite occurs: the fatigue limit defined as the maximum stress at the notch is higher than that achieved with smooth specimens. These two effects have been taken into account in most design handbooks with the help of experimental formulas or design curves. The basic idea of this study is that the size effect can mainly be explained by the statistical size effect. A component subjected to an alternating load can be assumed to form a sample of initiated cracks at the end of the crack initiation phase. The size of the sample depends on the size of the specimen in question. The main objective of this study is to develop a statistical model for the estimation of this kind of size effect. It was shown that the size of a sample of initiated cracks shall be based on the stressed surface area of the specimen. In case of varying stress distribution, an effective stress area must be calculated. It is based on the decreasing probability of equally sized initiated cracks at lower stress level. If the distribution function of the parent population of cracks is known, the distribution of the maximum crack size in a sample can be defined. This makes it possible to calculate an estimate of the largest expected crack in any sample size. The estimate of the fatigue limit can now be calculated with the help of the linear elastic fracture mechanics. In notched components another source of size effect has to be taken into account. If we think about two specimens which have similar shape, but the size is different, it can be seen that the stress gradient in the smaller specimen is steeper. If there is an initiated crack in both of them, the stress intensity factor at the crack in the larger specimen is higher. The second goal of this thesis is to create a calculation method for this factor which is called the geometric size effect. The proposed method for the calculation of the geometric size effect is also based on the use of the linear elastic fracture mechanics. It is possible to calculate an accurate value of the stress intensity factor in a non linear stress field using weight functions. The calculated stress intensity factor values at the initiated crack can be compared to the corresponding stress intensity factor due to constant stress. The notch size effect is calculated as the ratio of these stress intensity factors. The presented methods were tested against experimental results taken from three German doctoral works. Two candidates for the parent population of initiated cracks were found: the Weibull distribution and the log normal distribution. Both of them can be used successfully for the prediction of the statistical size effect for smooth specimens. In case of notched components the geometric size effect due to the stress gradient shall be combined with the statistical size effect. The proposed method gives good results as long as the notch in question is blunt enough. For very sharp notches, stress concentration factor about 5 or higher, the method does not give sufficient results. It was shown that the plastic portion of the strain becomes quite high at the root of this kind of notches. The use of the linear elastic fracture mechanics becomes therefore questionable.

Calculation of the critical crack size for cold form rectangular hollow section tube (CRHS) under bending load at -40º C temperature

To predict the capacity of the structure or the point which is followed by instability, calculation of the critical crack size is important. Structures usually contain several cracks but not necessarily all of these cracks lead to failure or reach the critical size. So, defining the harmful cracks or the crack size which is the most leading one to failure provides criteria for structure’s capacity at elevated temperature. The scope of this thesis was to calculate fracture parameters like stress intensity factor, the J integral and plastic and ultimate capacity of the structure to estimate critical crack size for this specific structure. Several three dimensional (3D) simulations using finite element method by Ansys program and boundary element method by Frank 3D program were carried out to calculate fracture parameters and results with the aid of laboratory tests (loaddisplacement curve, the J resistance curve and yield or ultimate stress) leaded to extract critical size of the crack. Two types of the fracture which is usually affected by temperature, Elastic and Elasti-Plastic fractures were simulated by performing several linear elastic and nonlinear elastic analyses. Geometry details of the weldment; flank angle and toe radius were also studied independently to estimate the location of crack initiation and simulate stress field in early stages of crack extension in structure. In this work also overview of the structure’s capacity in room temperature (20 ºC) was studied. Comparison of the results in different temperature (20 ºC and -40 ºC) provides a threshold of the structure’s behavior within the defined range.

Uutto-olosuhteiden vaikutus kasviperäisen indigon saantoon

Indigo on väriaine, jota valmistetaan petrokemianteollisuuden välituotteena syntyvästä aniliinista. Indigolla on kuitenkin pitkä historia. Sitä on valmistettu perinteisesti eri viljelykasveista, joista Euroopassa merkittävin on ollut morsinko. Luonnonmukaisten tuotteiden suosion kasvaessa on ryhdytty selvittämään morsingon viljelyn potentiaalia. Viljelyn kannattavuuden kannalta olennaista on kasvin lehdissä esiintyvien indigon esiasteiden mahdollisimman täydellinen eristäminen. Indigoa tuotetaan uuttamalla indigon esiasteet veteen. Esiasteet hajoavat synnyttäen indoksyyliä, josta hapen vaikutuksella muodostuu indigoa. Syntynyt indigo saostuu ja laskeutuu pohjalle. Samalla kuitenkin tapahtuu epätoivottuja sivureaktioita, jotka vähentävät indigon saantoa. Tutkimuksen tavoitteena oli laboratorio- ja kenttäkokeiden avulla löytää indigon saantoa parantavat uutto-olosuhteet. Kokeiden perusteella havaittiin, että indigon saantoon vaikuttavat positiivisesti pH:n laskeminen, lämpötilan nostaminen, morsingon lehtien pilkkominen ja uuttoliuoksen sekoittaminen. Uuttoliuoksen suolapitoisuuden havaittiin puolestaan vaikuttavan indigon saantoon negatiivisesti. Laboratoriokokeiden perusteella havaittu pH:n laskemisen vaikutus indigon saantoon todistettiin myös kenttäolosuhteissa. Kokeiden havaintojen perusteella esitettiin olosuhteiden indigosaantoa parantavien vaikutusten johtuvan kahdesta tekijästä: indoksyylin stabiloitumisesta happamassa ympäristössä, jolloin sivureaktioiden osuus vähenee, sekä aineensiirron paranemisella sekoituksen, faasien rajapinnan kasvamisen ja etenkin lehtien vahakerroksen rikkoutumisen kuuman veden ja hapon vaikutuksesta.

Improving the calculation of rate of stratification in APROS

APROS (Advanced Process Simulation Environment) is a computer simulation program developed to simulate thermal hydraulic processes in nuclear and conventional power plants. Earlier research at VTT Technological Research Centre of Finland had found the current version of APROS to produce inaccurate simulation results for a certain case of loop seal clearing. The objective of this Master’s thesis is to find and implement an alternative method for calculating the rate of stratification in APROS, which was found to be the reason for the inaccuracies. Brief literature study was performed and a promising candidate for the new method was found. The new method was implemented into APROS and tested against experiments and simulations from two test facilities and the current version of APROS. Simulation results with the new version were partially conflicting; in some cases the new method was more accurate than the current version, in some the current method was better. Overall, the new method can be assessed as an improvement.

Insulation System in an Integrated Motor Compressor

A high-speed and high-voltage solid-rotor induction machine provides beneficial features for natural gas compressor technology. The mechanical robustness of the machine enables its use in an integrated motor-compressor. The technology uses a centrifugal compressor, which is mounted on the same shaft with the high-speed electrical machine driving it. No gearbox is needed as the speed is determined by the frequency converter. The cooling is provided by the process gas, which flows through the motor and is capable of transferring the heat away from the motor. The technology has been used in the compressors in the natural gas supply chain in the central Europe. New areas of application include natural gas compressors working at the wellheads of the subsea gas reservoir. A key challenge for the design of such a motor is the resistance of the stator insulation to the raw natural gas from the well. The gas contains water and heavy hydrocarbon compounds and it is far harsher than the sales gas in the natural gas supply network. The objective of this doctoral thesis is to discuss the resistance of the insulation to the raw natural gas and the phenomena degrading the insulation. The presence of partial discharges is analyzed in this doctoral dissertation. The breakdown voltage of the gas is measured as a function of pressure and gap distance. The partial discharge activity is measured on small samples representing the windings of the machine. The electrical field behavior is also modeled by finite element methods. Based on the measurements it has been concluded that the discharges are expected to disappear at gas pressures above 4 – 5 bar. The disappearance of discharges is caused by the breakdown strength of the gas, which increases as the pressure increases. Based on the finite element analysis, the physical length of a discharge seen in the PD measurements at atmospheric pressure was approximated to be 40 – 120 m. The chemical aging of the insulation when exposed to raw natural gas is discussed based on a vast set of experimental tests with the gas mixture representing the real gas mixture at the wellhead. The mixture was created by mixing dry hydrocarbon gas, heavy hydrocarbon compounds, monoethylene glycol, and water. The mixture was chosen to be more aggressive by increasing the amount of liquid substances. Furthermore, the temperature and pressure were increased, which resulted in accelerated test conditions. The time required to detect severe degradation was thus decreased. The test program included a comparison of materials, an analysis of the e ects of di erent compounds in the gas mixture, namely water and heavy hydrocarbons, on the aging, an analysis of the e ects of temperature and exposure duration, and also an analysis on the e ect of sudden pressure changes on the degradation of the insulating materials. It was found in the tests that an insulation consisting of mica, glass, and epoxy resin can tolerate the raw natural gas, but it experiences some degradation. The key material in the composite insulation is the resin, which largely defines the performance of the insulation system. The degradation of the insulation is mostly determined by the amount of gas mixture di used into it. The di usion was seen to follow Fick’s second law, but the coe cients were not accurately defined. The di usion was not sensitive to temperature, but it was dependent upon the thermodynamic state of the gas mixture, in other words, the amounts of liquid components in the gas. The weight increase observed was mostly related to heavy hydrocarbon compounds, which act as plasticizers in the epoxy resin. The di usion of these compounds is determined by the crosslink density of the resin. Water causes slight changes in the chemical structure, but these changes do not significantly contribute to the aging phenomena. Sudden changes in pressure can lead to severe damages in the insulation, because the motion of the di used gas is able to create internal cracks in the insulation. Therefore, the di usion only reduces the mechanical strength of the insulation, but the ultimate breakdown can potentially be caused by a sudden drop in the pressure of the process gas.

Hitsatun alumiinikappaleen anodisointi

Tämän työn tarkoituksena oli selvittää, mitä on alumiinin pintakäsittelymenetelmä anodisointi ja kuinka se tapahtuu. Esille otettu esimerkkitapaus liittyy hitsatun alumiinin anodisointiin ja siinä ilmenneisiin ongelmiin.

Kalsinaattorin siirtymien ja teräskuoren murtumien tutkiminen

Sementti on yksi eniten maailmassa käytetty rakennusmateriaali ja Suomessa sementin valmistuksesta vastaa Finnsementti Oy kahden tehtaan voimin. Lappeenrannan tehtaalle investoitiin uusi uunilinja vuonna 2007, joka on aikansa kehittyneintä tekniikkaa. Järjes-telmän esilämmitysvaiheen laitteissa, erityisesti kalsinaattorissa, on esiintynyt luvattoman paljon plastisoitumista ja murtumia. Tässä työssä tutkittiin lämpötilan ja sen vaihtelun vaikutusta järjestelmässä syntyneisiin siirtymiin ja murtumiin. Työn alussa luotiin katsaus erilaisiin murtumisilmiöihin ja niiden syntyyn. Vuorauksessa käytettyihin tiilien käyttäytymistä tutkittiin myös, koska ne ovat olennainen osa esilämmi-tysjärjestelmää. Työn kokeellisessa osuudessa aluksi määriteltiin järjestelmässä käytetylle teräkselle lujuusominaisuudet tutkimalla mikrorakennetta sekä suorittamalla veto- että kovuuskokeet materiaalille. Toisessa osiossa mitattiin järjestelmän alasajon aikana tapah-tuneet siirtymät. Laskennallisessa osuudessa tutkittiin väsymismurtuman mahdollisuutta sekä määritettiin kuoressa esiintyvän särön vaikutusta puhkeamis- ja murtumiskuormituk-seen. FEM- analyysissä tarkasteltiin lämpötilan vaikutusta siirtymien suuruuksiin ja pyrittiin löytämään perusteluita, miksi rakenne on todellisuudessa siirtynyt eri suuntiin kuin alun perin oli tarkoitettu. Lisäksi analysoitiin FEM- mallit tiilihyllystä ja kalsinaattorin kuoren tukikehästä, joista tutkittiin lämpökuorman aiheuttamia jännityksiä. Materiaalin osalta selvisi, että kyseessä oli hyvin yleinen rakenneteräs S235 tai sitä vas-taava teräslaatu. Teräs ei ominaisuuksiltaan sovellu kuumiin olosuhteisiin, jonka vuoksi järjestelmässä käytettävän eristevuorauksen kunto on erityisen tärkeä rakenteen käyttöiän kannalta. Vuorauksen kunnosta riippuu, kuinka suuren lämpökuorman teräskuori saa. Väsymismurtuman mahdollisuus jäi minimaalisen pieneksi lämpötilan muutoksen vaiku-tuksesta. Analysoinnin tulosten perusteella voitiin todeta, että lämpötilan hitaasti mutta kohtalaisen suurella vaihteluvälillä sekä tiilien turpoamisen vaikutuksella on erittäin suuri merkitys järjestelmässä esiintyviin murtumiin.

Väsymiskestävyyden määritys murtumismekaanisilla särönmallinnusohjelmilla

Tässä työssä tutkitaan Wärtsilä Oyj:n moottorin ja ABB Oy:n generaattorin muodostaman aggregaatin väsymiskestävyyttä lineaarisen murtumismekaniikan avulla. Työn tavoitteena on selvittää ABAQUS/XFEM- ja FRANC3D-ohjelman soveltuvuus kuormitukseltaan ja geometrialtaan vaativan generaattorirungon suunnittelutyökaluksi. Generaattorirungon kuormitukset aiheutuvat aggregaatin käynnin sekä käynnistys- ja sammutusvaiheen aikai-sista syntyvistä värähtelyistä. Tutkimuksessa tarkastellaan generaattorirungon väsymistä käynninaikaisella kuormituksella. Työssä mallinnettiin generaattorirungosta valittu hitsausdetalji alimallinnustekniikalla, jolloin alimallin reunaehdot voitiin määrittää aggregaatille tehdyn vastelaskennan perus-teella. Alimallista tutkittiin kahta erilaista hitsiliitostyyppiä, joihin mallinnettiin XFEM- ja FRANC3D-ohjelmilla erikokoisia säröjä hitsiliitosten rajaviivalle sekä juuren puolelle. Tutkittavilla ohjelmilla saatujen jännitysintensiteettikertoimien avulla säröille voitiin las-kea ekvivalentti jännitysintensiteettikerroin, jota verrattiin kokeellisesti saatuun jännitysin-tensiteettikertoimen kynnysarvoon. XFEM- ja FRANC3D-ohjelmia vertailtiin käytön helppouden, tulosten tarkkuuden sekä laskenta-aikojen perusteella. Käytettävyyden ja laskenta-aikojen perusteella XFEM-ohjelma soveltui paremmin käytettäväksi teollisuudessa suunnittelu- ja kehitystyön apu-työkaluna. FRANC3D taas antoi XFEM-ohjelmaa luotettavampia tuloksia, mutta laskenta-ajat olivat moninkertaiset.

Kytkentäaineet puumuovikomposiiteissa

Puumuovikomposiittien valmistuksessa yhdistetään kaksi toisistaan eroavaa materiaalia jolloin saadaan aikaan materiaalien ominaisuuksien ainutlaatuinen yhdistelmä. Polymeerimateriaaleina käytetään pääasiassa erilaisia kestomuoveja. Kuitumateriaaleina voidaan käyttää puujauhetta, sahanpurua, paperin- ja kartongin valmistuksessa käytettävää sellua, nanoselluloosaa tai muita puukuitumateriaaleja. Polaarisen puukuidun ja polaarittoman muovimateriaalin välinen materiaalien rajapinnan adheesio on yleensä riittämätöntä, mikä vaikuttaa lopputuotteen ominaisuuksien heikkenemiseen. Kyseinen ongelma on pyritty ratkaisemaan käyttämällä erilaisia kytkentäaineita. Tässä työssä keskitytään käsittelemään erilaisia puumuovikomposiittien kytkentäaineita, niiden toimintaa sekä vaikutuksia lopputuotteeseen. Lisäksi työssä esitellään myös puumuovikomposiittien valmistusmateriaaleja ja valmistusprosesseja.

Model-based estimation of liquid flows in the blast furnace hearth and taphole

This thesis presents a set of methods and models for estimation of iron and slag flows in the blast furnace hearth and taphole. The main focus was put on predicting taphole flow patterns and estimating the effects of various taphole conditions on the drainage behavior of the blast furnace hearth. All models were based on a general understanding of the typical tap cycle of an industrial blast furnace. Some of the models were evaluated on short-term process data from the reference furnace. A computational fluid dynamics (CFD) model was built and applied to simulate the complicated hearth flows and thus to predict the regions of the hearth exerted to erosion under various operating conditions. Key boundary variables of the CFD model were provided by a simplified drainage model based on the first principles. By examining the evolutions of liquid outflow rates measured from the furnace studied, the drainage model was improved to include the effects of taphole diameter and length. The estimated slag delays showed good agreement with the observed ones. The liquid flows in the taphole were further studied using two different models and the results of both models indicated that it is more likely that separated flow of iron and slag occurs in the taphole when the liquid outflow rates are comparable during tapping. The drainage process was simulated with an integrated model based on an overall balance analysis: The high in-furnace overpressure can compensate for the resistances induced by the liquid flows in the hearth and through the taphole. Finally, a recently developed multiphase CFD model including interfacial forces between immiscible liquids was developed and both the actual iron-slag system and a water-oil system in laboratory scale were simulated. The model was demonstrated to be a useful tool for simulating hearth flows for gaining understanding of the complex phenomena in the drainage of the blast furnace.

Puristussylinterien valmistuksen kehittäminen

Tässä diplomityössä kehitettiin yksitoimisten puristussylinterien valmistusta Rautessa. Sylinterien valmistuksessa haastavin vaihe on sylinteriputken ja pohjan välinen hitsaus. Hitsauksen avuksi suunniteltiin sylinterin sisäpuolinen juuritukilaite. Hitsauskokeita suoritettiin hitsin pohjan jauhekaarihitsaukselle ja MAG-hitsaukselle. Juuritukilaitteen toimivuutta testattiin koehitsauksilla. Puristussylinterien materiaali on S355J2-terästä, jonka ainevahvuus on 20 – 60 mm. Paksujen rakenneterästen hitsauksessa täytyy ottaa huomioon hitsausliitoksen mekaanisten ominaisuuksien muuttuminen sekä eri halkeamien synty. Hitsauksen laatuun ja laadunhallintaan voidaan vaikuttaa monien eri tekijöiden avulla. Hitsausohjeen avulla, ja muut laatutekijät huomioiden, voidaan hitseille asetetut laatukriteerit täyttää. Juurituen käyttö nopeuttaa puristussylinterien hitsausta vähintään 50 %. Jauhekaarihitsaus kuparista juuritukea vasten synnyttää vaikeasti poistettavan kuonan juuren puolelle. Perinteinen MAG-hitsaus kuparista juuritukea vasten sisältää liian monta muuttujaa, mikä tekee siitä epäluotettavan pohjapalon hitsaukseen. Työssä suunnitellun juuritukilaitteen käyttö tuotannossa vaatii lisää hitsauskokeita.

Development of a process for the direct synthesis of hydrogen peroxide in a novel microstructured reactor

Microreactors have proven to be versatile tools for process intensification. Over recent decades, they have increasingly been used for product and process development in chemical industries. Enhanced heat and mass transfer in the reactors due to the extremely high surfacearea- to-volume ratio and interfacial area allow chemical processes to be operated at extreme conditions. Safety is improved by the small holdup volume of the reactors and effective control of pressure and temperature. Hydrogen peroxide is a powerful green oxidant that is used in a wide range of industries. Reduction and auto-oxidation of anthraquinones is currently the main process for hydrogen peroxide production. Direct synthesis is a green alternative and has potential for on-site production. However, there are two limitations: safety concerns because of the explosive gas mixture produced and low selectivity of the process. The aim of this thesis was to develop a process for direct synthesis of hydrogen peroxide utilizing microreactor technology. Experimental and numerical approaches were applied for development of the microreactor. Development of a novel microreactor was commenced by studying the hydrodynamics and mass transfer in prototype microreactor plates. The prototypes were designed and fabricated with the assistance of CFD modeling to optimize the shape and size of the microstructure. Empirical correlations for the mass transfer coefficient were derived. The pressure drop in micro T-mixers was investigated experimentally and numerically. Correlations describing the friction factor for different flow regimes were developed and predicted values were in good agreement with experimental results. Experimental studies were conducted to develop a highly active and selective catalyst with a proper form for the microreactor. Pd catalysts supported on activated carbon cloths were prepared by different treatments during the catalyst preparation. A variety of characterization methods were used for catalyst investigation. The surface chemistry of the support and the oxidation state of the metallic phase in the catalyst play important roles in catalyst activity and selectivity for the direct synthesis. The direct synthesis of hydrogen peroxide was investigated in a bench-scale continuous process using the novel microreactor developed. The microreactor was fabricated based on the hydrodynamic and mass transfer studies and provided a high interfacial area and high mass transfer coefficient. The catalysts were prepared under optimum treatment conditions. The direct synthesis was conducted at various conditions. The thesis represents a step towards a commercially viable direct synthesis. The focus is on the two main challenges: mitigating the safety problem by utilization of microprocess technology and improving the selectivity by catalyst development.

Computational studies for the design of process equipment with complex geometries

This study combines several projects related to the flows in vessels with complex shapes representing different chemical apparata. Three major cases were studied. The first one is a two-phase plate reactor with a complex structure of intersecting micro channels engraved on one plate which is covered by another plain plate. The second case is a tubular microreactor, consisting of two subcases. The first subcase is a multi-channel two-component commercial micromixer (slit interdigital) used to mix two liquid reagents before they enter the reactor. The second subcase is a micro-tube, where the distribution of the heat generated by the reaction was studied. The third case is a conventionally packed column. However, flow, reactions or mass transfer were not modeled. Instead, the research focused on how to describe mathematically the realistic geometry of the column packing, which is rather random and can not be created using conventional computeraided design or engineering (CAD/CAE) methods. Several modeling approaches were used to describe the performance of the processes in the considered vessels. Computational fluid dynamics (CFD) was used to describe the details of the flow in the plate microreactor and micromixer. A space-averaged mass transfer model based on Fick’s law was used to describe the exchange of the species through the gas-liquid interface in the microreactor. This model utilized data, namely the values of the interfacial area, obtained by the corresponding CFD model. A common heat transfer model was used to find the heat distribution in the micro-tube. To generate the column packing, an additional multibody dynamic model was implemented. Auxiliary simulation was carried out to determine the position and orientation of every packing element in the column. This data was then exported into a CAD system to generate desirable geometry, which could further be used for CFD simulations. The results demonstrated that the CFD model of the microreactor could predict the flow pattern well enough and agreed with experiments. The mass transfer model allowed to estimate the mass transfer coefficient. Modeling for the second case showed that the flow in the micromixer and the heat transfer in the tube could be excluded from the larger model which describes the chemical kinetics in the reactor. Results of the third case demonstrated that the auxiliary simulation could successfully generate complex random packing not only for the column but also for other similar cases.

Membrane properties of structurally modified ceramides : effects on lipid lateral distribution and sphingomyelin-interactions in artificial bilayer membranes

Ceramides comprise a class of sphingolipids that exist only in small amounts in cellular membranes, but which have been associated with important roles in cellular signaling processes. The influences that ceramides have on the physical properties of bilayer membranes reach from altered thermodynamical behavior to significant impacts on the molecular order and lateral distribution of membrane lipids. Along with the idea that the membrane physical state could influence the physiological state of a cell, the membrane properties of ceramides have gained increasing interest. Therefore, membrane phenomena related to ceramides have become a subject of intense study both in cellular as well as in artificial membranes. Artificial bilayers, the so called model membranes, are substantially simpler in terms of contents and spatio-temporal variation than actual cellular membranes, and can be used to give detailed information about the properties of individual lipid species in different environments. This thesis focuses on investigating how the different parts of the ceramide molecule, i.e., the N-linked acyl chain, the long-chain sphingoid base and the membrane-water interface region, govern the interactions and lateral distribution of these lipids in bilayer membranes. With the emphasis on ceramide/sphingomyelin(SM)-interactions, the relevance of the size of the SMhead group for the interaction was also studied. Ceramides with methylbranched N-linked acyl chains, varying length sphingoid bases, or methylated 2N (amide-nitrogen) and 3O (C3-hydroxyl) at the interface region, as well as SMs with decreased head group size, were synthesized and their bilayer properties studied by calorimetric and fluorescence spectroscopic techniques. In brief, the results showed that the packing of the ceramide acyl chains was more sensitive to methyl-branching in the mid part than in the distal end of the N-linked chain, and that disrupting the interfacial structure at the amide-nitrogen, as opposed to the C3-hydroxyl, had greater effect on the interlipid interactions of ceramides. Interestingly, it appeared that the bilayer properties of ceramides could be more sensitive to small alterations in the length of the long-chain base than what was previously reported for the N-linked acyl chain. Furthermore, the data indicated that the SM-head group does not strongly influence the interactions between SMs and ceramides. The results in this thesis illustrate the pivotal role of some essential parts of the ceramide molecules in determining their bilayer properties. The thesis provides increased understanding of the molecular aspects of ceramides that possibly affect their functions in biological membranes, and could relate to distinct effects on cell physiology.

Reducing contact resistance in graphene devices

In this thesis, the contact resistance of graphene devices was investigated because high contact resistance is detrimental to the performance of graphene field-effect transistors (GFET). Method for increasing so-called edge-contact area was applied in device fabrication process, as few nanometers thick Ni layer was used as a catalytic etchant during the annealing process. Finally, Ni was also used as a metal for contact. GFETs were fabricated using electron beam lithography using graphene fabricated by chemical vapor deposition (CVD). Critical part of the fabrication process was to preserve the high quality of the graphene channel while etching the graphene at contact areas with Ni during the annealing. This was achieved by optimizing the combination of temperature and gas flows. The structural properties of graphene were studied using scanning electron microscopy, scanning confocal μ-Raman spectroscopy and optical microscopy. Evaluation of electric transport properties including contact resistance was carried out by transmission line method and four-probe method. The lowest contact resistance found was about at 350 Ωμm. In addition, different methods to transfer CVD graphene synthesized on copper were studied. Typical method using PMMA as a supporting layer leaves some residues after its removal, thus effecting on the performance of a graphene devices. In a metal assisted transfer method, metal is used as an interfacial layer between PMMA and graphene. This allows more effective removal of PMMA. However, Raman spectra of graphene transferred by metal assisted method showed somewhat lower quality than the PMMA assisted method