26 resultados para HYPERAROMATIC STABILIZATION
Resumo:
In this thesis, the gas sensing properties of porous silicon-based thin-film optical filters are explored. The effects of surface chemistry on the adsorption and desorption of various gases are studied in detail. Special emphasis is placed on investigating thermal carbonization as a stabilization method for optical sensing applications. Moreover, the possibility of utilizing the increased electrical conductivity of thermally carbonized porous silicon for implementing a multiparametric gas sensor, which would enable simultaneous monitoring of electrical and optical parameters, is investigated. In addition, different porous silicon-based optical filter-structures are prepared, and their properties in sensing applications are evaluated and compared. First and foremost, thermal carbonization is established as a viable method to stabilize porous silicon optical filters for chemical sensing applications. Furthermore, a multiparametric sensor, which can be used for increasing selectivity in gas sensing, is also demonstrated. Methods to improve spectral quality in multistopband mesoporous silicon rugate filters are studied, and structural effects to gas sorption kinetics are evaluated. Finally, the stability of thermally carbonized optical filters in basic environments is found to be superior in comparison to other surface chemistries currently available for porous silicon. The results presented in this thesis are of particular interest for developing novel reliable sensing systems based on porous silicon, e.g., label-free optical biosensors.
Resumo:
Electrochemical double-layer supercapacitors have an intermediate position between rechargeable batteries, which can store high amounts of energy, and dielectric capacitors, which have high output power. Supercapacitors are widely suggested to be used in automobiles (recuperation during braking, facilitate engine starting, electric stabilization of the system), industry (forklifts, elevators), hybrid off-road machinery and also in consumer electronics. Supercapacitor electrodes require highly porous material. Typically, activated carbon is used. Specific surface area of activated carbon is approximately 1000 m2 per gram. Carbon nanotubes represent one of prospective materials. According to numerous studies this material allows to improve the properties of supercapacitors. The task of this Master‘s Thesis was to test multiwalled carbon nanotubes and become confident with the testing methods.
Resumo:
Maailman laajuisen kasvihuoneilmiön kiihtyminen ja EU:n tiukentuneet jäsenmailleen asettamat tavoitteet uusiutuvien polttoaineiden käytön lisäämiseksi ovat lisänneet puupolttoaineiden käyttöä Suomessa. Lisääntynyt puupolttoaineiden käyttö ja entistä tehokkaampi hakkuutähteiden hyödyntäminen on lisännyt metsistä poistuvien ravinteiden määrää. Huoli metsien maaperän ravinteiden niukkenemisesta sekä tiukentunut lainsäädäntö tuhkien kaatopaikkasijoittamisesta ovat lisänneet energiayhtiöiden kiinnostusta lisätä tuhkien hyötykäyttöä. Tuhka täytyy esikäsitellä, eli stabiloida ennen hyötykäyttöä. Stabiloinnissa tuhkaa kostutetaan, jolloin siitä muodostuu rakeita. Hyödynnettäessä tuhkaa metsälannoitukseen tuhka tulee usein myös terästää typellä, sillä tuhka ei sisällä lainkaan typpeä. Muita tuhkan hyötykäyttömahdollisuuksia ovat peltolannoitus, betonin valmistus, maarakentaminen sekä jätevedenpuhdistus. Näistä vaihtoehdoista betonin valmistus ja maarakentaminen ovat melko yleisiä. Kouvolassa tuhkaa muodostuu noin 14 000 tonnia vuodessa. Kaupungin omistama metsäalue Saaramaalla voitaisiin lannoittaa lähes samoilla kustannuksilla kuin mitä kaatopaikkasijoittaminen maksaisi. Sen sijaan tuhkan käytöllä tierakentamiseen Tähteen alueella saavutetaan tuhansien eurojen säästöt kaatopaikkasijoitukseen verrattuna ja samalla tuhka saadaan hyötykäyttöön kiviaineksia säästäen.
Resumo:
In this work emission, optical, electrical and magnetic properties of the d- and f- elements doped zinc selenide crystals were investigated within a wide temperature range. Doping was performed in various technological processes: during the growth by chemical vapor transport method; by thermal diffusion from the Bi or Zn melt. Concentration of the doping impurity in the crystals was controlled by amount of the dopant in the source material or by its concentration in the doping media. Special interest in the work was paid to the influence of the different concentrations of Cr and Yb impurities on ZnSe crystals’ properties, correlations between observed effects and similarities with the Ni, Mn and Gd dopants are analysed. Possibility of formation of the excitons bound to the doping d-ions was shown. In contrast to this, it was observed that f-elements do not bound excitons, but prevent formation of excitons bound to some uncontrolled impurities. A mechanism of Cr doping impurity interaction with background impurities and zinc selenide structural defects was proposed based on experimental data. An assumption about resonant energy transfer between double charged chromium ions and complexes based on crystals’ vacancy defects was made. A correlation between emission and magnetic properties of the d- ions doped samples was established. Based on this correlation a mechanism explaining the concentration quench of the emission was proposed. It was found that f-ions bind electrically active shallow and deep donor and acceptor states of background impurity to electrically neutral complexes. This may be observed as “purification” of ZnSe crystals by doping with the rare-earth elements, resulting i tendency of the properties of f-ion doped crystals to the properties of intrinsic crystals, but with smaller concentration of uncontrolled native and impurity defects. A possible interpretation of this effect was proposed. It was shown that selenium substituting impurities decrease efficiency of the Yb doping. Based on this experimental results an attempt to determine ytterbium ion surroundings in the crystal lattice was made. It was shown that co-doping of zinc selenide crystals with the d- and f- ions leads to the combination of the impurities influence on the material’s properties. On the basis of obtained data an interaction mechanism of the d- and f-elements co-dopants was proposed. Guided by the model of the ytterbium ion incorporation in the selenide sublattice of the ZnSe crystals, an assumption about stabilization of single charged chromium ions in the zinc sublattice crystal nodes, by means of formation of the local charge compensating clusters, was made.
Resumo:
Tässä kandidaatintyössä selvitettiin, onko 28 vuorokautta riittävä aika sinkillä pilaantuneen maaperän massastabilointiin, ja kuinka sinkin esiintymismuoto vaikuttaa sen stabilointiaikaan. Kokeellisessa osassa jäljiteltiin malmijätteessä, orgaanisessa aineksessa sekä liuenneena maaperässä esiintyvän sinkin stabiloitumista lisäämällä maanäytteeseen sinkkiä eri yhdisteinä; sinkkirakeina, -kloridina ja -asetaattina. Näytteet stabiloitiin sementti-lentotuhkaseoksella 1–28 vuorokauden pituisia ajanjaksoja, minkä jälkeen ne kuvattiin pyyhkäisyelektronimikroskoopilla (SEM) ja niille tehtiin liukoisuustestit. Liukoisuustestien tuloksista voidaan huomata sinkkikloridin stabiloituvan jo ensimmäisen vuorokauden aikana ja pysyvän samalla tasolla koko tarkasteluajan. Sinkkirakeiden ja -asetaatin stabiloituminen ei ole yhtä tasaista; alun sitoutumisen jälkeen niiden liukoisuuksissa on havaittavissa selkeät piikit 21 vuorokauden kohdalla. Tämän jälkeen ne alkavat sitoutua uudelleen. Tulosten perusteella sinkin esiintymismuoto vaikuttaa sen stabilointiaikaan, eikä 28:aa vuorokautta voida pitää riittävänä aikana sinkillä pilaantuneen maa-aineksen stabilointiin. Vaikka liukoinen sinkki stabiloituu jo yhdessä vuorokaudessa, ei malmijätteessä tai orgaanisessa aineksessa esiintyvä sinkki ehdi stabiloitua vakaalle tasolle vielä 28 vuorokaudenkaan aikana. Tämä tulisi ottaa huomioon suunniteltaessa ja toteutettaessa sinkkiä sisältävien maiden kunnostushankkeita.
Resumo:
Bauksiittijäte on alumiinin jalostuksessa syntyvä sivutuote, jonka alkalisuus on riski lähiympäristön ekosysteemeille. Alkalisuuden aiheuttamaan riskiin etsittiin ratkaisua perehtymällä bauksiittijätteen käsittelyyn. Kandidaatintyössä esitettiin eri menetelmiä bauksiittijätteen neutraloimiseksi, stabiloimiseksi ja varastoimiseksi. Menetelmien periaatteet määritettiin kirjallisuudesta löytyvien tutkimusten pohjalta, joiden perusteella voitiin määrittää toimivimmat menetelmät bauksiittijätteen käsittelemiseksi. Käytännöllisimmiksi käsittelymenetelmiksi osoittautuivat meriveden ja/tai hiilidioksidin lisääminen bauksiittijätteeseen sen neutraloimiseksi. Bauksiittijätteen stabiloimiseksi siihen tulee lisätä kiinteää materiaalia, kuten kalkkia, kiintoainepitoisuuden nostamiseksi sekä kovettuvien yhdisteiden muodostumiseksi.
Resumo:
Full contour monolithic zirconia restorations have shown an increased popularity in the dental field over the recent years, owing to its mechanical and acceptable optical properties. However, many features of the restoration are yet to be researched and supported by clinical studies to confirm its place among the other indirect restorative materials This series of in vitro studies aimed at evaluating and comparing the optical and mechanical properties, light cure irradiance, and cement polymerization of multiple monolithic zirconia material at variable thicknesses, environments, treatments, and stabilization. Five different monolithic zirconia materials, four of which were partially stabilized and one fully stabilized were investigated. The optical properties in terms of surface gloss, translucency parameter, and contrast ratio were determined via a reflection spectrophotometer at variable thicknesses, coloring, sintering method, and after immersion in an acidic environment. Light cure irradiance and radiant exposure were quantified through the specimens at variable thicknesses and the degree of conversion of two dual-cure cements was determined via Fourier Transform Infrared spectroscopy. Bi-axial flexural strength was evaluated to compare between the partially and fully stabilized zirconia prepared using different coloring and sintering methods. Surface characterization was performed using a scanning electron microscope and a spinning disk confocal microscope. The surface gloss and translucency of the zirconia investigated were brand and thickness dependent with the translucency values decreasing as the thickness increased. Staining decreased the translucency of the zirconia and enhanced surface gloss as well as the flexural strength of the fully stabilized zirconia but had no effect on partially stabilized zirconia. Immersion in a corrosive acid increased surface gloss and decreased the translucency of some zirconia brands. Zirconia thickness was inversely related to the amount of light irradiance, radiant exposure, and degree of monomer conversion. Type of sintering furnace had no effect on the optical and mechanical properties of zirconia. Monolithic zirconia maybe classified as a semi-translucent material that is well influenced by the thickness, limiting its use in the esthetic zones. Conventional acid-base reaction, autopolymerizing and dual-cure cements are recommended for its cementation. Its desirable mechanical properties give it a high potential as a restoration for posterior teeth. However, close monitoring with controlled clinical studies must be determined before any definite clinical recommendations can be drawn.
Resumo:
Tässä kanditaatintyössä selvitettiin kuinka erilaiset sideaineseokset soveltuvat raskas-metallien sitomiseen 28 vuorokautta stabiloiduissa näytteistä. Työssä oletettiin teollisten jätefraktioiden käytön tehostavan eräiden metallien, kuten kupari ja sinkki, immobilisointia lievästi pilaantuneista maa-aineksista. Kokeellisessa osassa stabiloitiin Kokkolan satamasta ruopattua sedimenttiä, jonka sinkkipitoisuudet olivat ylittäneet saastuneen sedimentin ohjearvon (≥400 mg/kg). Sedimenttiin lisättiin eri sideaineseoksia ja näytteiden annettiin stabiloitua 28 vuorokautta, minkä jälkeen niistä testattiin liukenevat raskasmetallit muokatulla ravistelutestillä. Eri sideaineseoksilla saatuja tuloksia verrattiin pelkän yleissementin käyttöön. Lisäksi erillisistä näytteistä otettiin pyyhkäisyelektronimikros-koopilla (SEM) kuvia havainnollistamaan stabiloitumista. Näissä näytteissä käytettiin samoja sideaineita kuin tehdyissä kokeissa. Liukoisuustestien tuloksista voidaan huomata näytteissä ongelmalliseksi raskasmetalliksi identifioidun sinkin sitoutuvan parhaiten sementin ja kipsin sekoituksella. Myös tuhkaa sisältävät sideainesekoitukset pienensivät sinkin liukoisuutta verrattuna pelkkään yleis-sementtiin. Jatkotutkimuksissa voitaisiin testata erilaisia sideainesekoituksia betonira-kentamisessa, joilla saadaan ainakin 25 MPa lujuusarvo, pilaantunutta sedimenttiä tai maa-ainesta käyttäen.
Resumo:
Molecular oxygen (O2) is a key component in cellular respiration and aerobic life. Through the redox potential of O2, the amount of free energy available to organisms that utilize it is greatly increased. Yet, due to the nature of the O2 electron configuration, it is non-reactive to most organic molecules in the ground state. For O2 to react with most organic compounds it must be activated. By activating O2, oxygenases can catalyze reactions involving oxygen incorporation into organic compounds. The oxygen activation mechanisms employed by many oxygenases to have been studied, and they often include transition metals and selected organic compounds. Despite the diversity of mechanisms for O2 activation explored in this thesis, all of the monooxygenases studied in the experimental part activate O2 through a transient carbanion intermediate. One of these enzymes is the small cofactorless monooxygenase SnoaB. Cofactorless monooxygenases are unusual oxygenases that require neither transition metals nor cofactors to activate oxygen. Based on our biochemical characterization and the crystal structure of this enzyme, the mechanism most likely employed by SnoaB relies on a carbanion intermediate to activate oxygen, which is consistent with the proposed substrate-assisted mechanism for this family of enzymes. From the studies conducted on the two-component system AlnT and AlnH, both the functions of the NADH-dependent flavin reductase, AlnH, and the reduced flavin dependent monooxygenase, AlnT, were confirmed. The unusual regiochemistry proposed for AlnT was also confirmed on the basis of the structure of a reaction product. The mechanism of AlnT, as with other flavin-dependent monooxygenases, is likely to involve a caged radical pair consisting of a superoxide anion and a neutral flavin radical formed from an initial carbanion intermediate. In the studies concerning the engineering of the S-adenosyl-L-methionine (SAM) dependent 4-O-methylase DnrK and the homologous atypical 10-hydroxylase RdmB, our data suggest that an initial decarboxylation of the substrate is catalyzed by both of these enzymes, which results in the generation of a carbanion intermediate. This intermediate is not essential for the 4-O-methylation reaction, but it is important for the 10-hydroxylation reaction, since it enables substrate-assisted activation of molecular oxygen involving a single electron transfer to O2 from a carbanion intermediate. The only role for SAM in the hydroxylation reaction is likely to be stabilization of the carbanion through the positive charge of the cofactor. Based on the DnrK variant crystal structure and the characterizations of several DnrK variants, the insertion of a single amino acid in DnrK (S297) is sufficient for gaining a hydroxylation function, which is likely caused by carbanion stabilization through active site solvent restriction. Despite large differences in the three-dimensional structures of the oxygenases and the potential for multiple oxygen activation mechanisms, all the enzymes in my studies rely on carbanion intermediates to activate oxygen from either flavins or their substrates. This thesis provides interesting examples of divergent evolution and the prevalence of carbanion intermediates within polyketide biosynthesis. This mechanism appears to be recurrent in aromatic polyketide biosynthesis and may reflect the acidic nature of these compounds, propensity towards hydrogen bonding and their ability to delocalize π-electrons.
Resumo:
The signalling sphingolipid sphingosine-1-phosphate (S1P) is necessary for development of the immune system and vasculature and on a cellular level regulates migration, proliferation and survival. Due to these traits S1P has an important role in cancer biology. It is considered a primarily cancer-promoting factor and the enzyme which produces it, sphingosine kinase (SphK), is often over-expressed in tumours. S1P is naturally present in the blood, lymph, tissue fluids and cell cytoplasm and functions through its cell surface receptors (S1P1-5) and as an intracellular second messenger. Sphingosylphosphorylcholine (SPC) is closely related to S1P and has similar regulatory functions but has not been extensively studied. Both S1P and SPC are able to evoke either stimulatory or inhibitory effects on cancer cells depending on the context. The aim of this thesis work was to study novel regulatory targets of S1P and SPC, which mediate the effects of S1P/SPC signalling on cancer cell behaviour. The investigated targets are the transcription factor hypoxia-inducible factor 1 (HIF-1), the intermediate filament protein vimentin and components of the Hippo signalling pathway. HIF-1 has a central role in cancer biology, as it regulates a multitude of cancer-related genes and is potently activated by intratumoural hypoxia through stabilization of the regulatory subunit HIF-1α. Tumours typically harbour high HIF-1α levels and HIF-1, in turn, facilitates tumour angiogenesis and metastasis and regulates cancer cell metabolism. We found S1P to induce follicular thyroid cancer cell migration in normal oxygen conditions by increasing HIF-1α synthesis and stability and subsequently HIF-1 activity. Vimentin is a central regulator of cell motility and is also commonly over-expressed in cancers. Vimentin filaments form a cytoskeletal network in mesenchymal cells as well as epithelial cancer cells which have gone through epithelial-mesenchymal transition (EMT). Vimentin is heavily involved in cancer cell invasion and gives tumours metastatic potential. We saw both S1P and SPC induce phosphorylation of vimentin monomers and reorganization of the vimentin filament network in breast and anaplastic thyroid cancer cells. We also found vimentin to mediate the anti-migratory effect of S1P/SPC on these cells. The Hippo pathway is a novel signalling cascade which controls cancer-related processes such as cellular proliferation and survival in response to various extracellular signals. The core of the pathway consists of the transcriptional regulators YAP and TAZ, which activate predominantly cancer-promoting genes, and the tumour suppressive kinases Lats1 and Lats2 which inhibit YAP/TAZ. Increased YAP expression and activity has been reported for a wide variety of cancers. We found SPC to regulate Hippo signalling in breast cancer cells in a two-fold manner through effects on phosphorylation status, activity and/or expression of YAP and Lats2. In conclusion, this thesis reveals new details of the signalling function of S1P and SPC and regulation of the central oncogenic factors HIF-1 and vimentin as well as the novel cancer-related pathway Hippo.
Resumo:
The present world energy production is heavily relying on the combustion of solid fuels like coals, peat, biomass, municipal solid waste, whereas the share of renewable fuels is anticipated to increase in the future to mitigate climate change. In Finland, peat and wood are widely used for energy production. In any case, the combustion of solid fuels results in generation of several types of thermal conversion residues, such as bottom ash, fly ash, and boiler slag. The predominant residue type is determined by the incineration technology applied, while its composition is primarily relevant to the composition of fuels combusted. An extensive research has been conducted on technical suitability of ash for multiple recycling methods. Most of attention was drawn to the recycling of the coal combustion residues, as coal is the primary solid fuel consumed globally. The recycling methods of coal residues include utilization in a cement industry, in concrete manufacturing, and mine backfilling, to name few. Biomass combustion residues were also studied to some extent with forest fertilization, road construction, and road stabilization being the predominant utilization options. Lastly, residues form municipal solid waste incineration attracted more attention recently following the growing number of waste incineration plants globally. The recycling methods of waste incineration residues are the most limited due to its hazardous nature and varying composition, and include, among others, landfill construction, road construction, mine backfilling. In the study, environmental and economic aspects of multiple recycling options of thermal conversion residues generated within a case-study area were studied. The case-study area was South-East Finland. The environmental analysis was performed using an internationally recognized methodology — life cycle assessment. Economic assessment was conducted applying a widely used methodology — cost-benefit analysis. Finally, the results of the analyses were combined to enable easier comparison of the recycling methods. The recycling methods included the use of ash in forest fertilization, road construction, road stabilization, and landfill construction. Ash landfilling was set as a baseline scenario. Quantitative data about the amounts of ash generated and its composition was obtained from companies, their environmental reports, technical reports and other previously published literature. Overall, the amount of ash in the case-study area was 101 700 t. However, the data about 58 400 t of fly ash and 35 100 t of bottom ash and boiler slag were included in the study due to lack of data about leaching of heavy metals in some cases. The recycling methods were modelled according to the scientific studies published previously. Overall, the results of the study indicated that ash utilization for fertilization and neutralization of 17 600 ha of forest was the most economically beneficial method, which resulted in the net present value increase by 58% compared to ash landfilling. Regarding the environmental impact, the use of ash in the construction of 11 km of roads was the most attractive method with decreased environmental impact of 13% compared to ash landfilling. The least preferred method was the use of ash for landfill construction since it only enabled 11% increase of net present value, while inducing additional 1% of negative impact on the environment. Therefore, a following recycling route was proposed in the study. Where possible and legally acceptable, recycle fly and bottom ash for forest fertilization, which has strictest requirements out of all studied methods. If the quality of fly ash is not suitable for forest fertilization, then it should be utilized, first, in paved road construction, second, in road stabilization. Bottom ash not suitable for forest fertilization, as well as boiler slag, should be used in landfill construction. Landfilling should only be practiced when recycling by either of the methods is not possible due to legal requirements or there is not enough demand on the market. Current demand on ash and possible changes in the future were assessed in the study. Currently, the area of forest fertilized in the case-study are is only 451 ha, whereas about 17 600 ha of forest could be fertilized with ash generated in the region. Provided that the average forest fertilizing values in Finland are higher and the area treated with fellings is about 40 000 ha, the amount of ash utilized in forest fertilization could be increased. Regarding road construction, no new projects launched by the Center of Economic Development, Transport and the Environment in the case-study area were identified. A potential application can be found in the construction of private roads. However, no centralized data about such projects is available. The use of ash in stabilization of forest roads is not expected to increased in the future with a current downwards trend in the length of forest roads built. Finally, the use of ash in landfill construction is not a promising option due to the reducing number of landfills in operation in Finland.