Numerical simulation of two-chamber plasma sources using finite element method

Numerical simulation of plasma sources is very important. Such models allows to vary different plasma parameters with high degree of accuracy. Moreover, they allow to conduct measurements not disturbing system balance.Recently, the scientific and practical interest increased in so-called two-chamber plasma sources. In one of them (small or discharge chamber) an external power source is embedded. In that chamber plasma forms. In another (large or diffusion chamber) plasma exists due to the transport of particles and energy through the boundary between chambers.In this particular work two-chamber plasma sources with argon and oxygen as active mediums were onstructed. This models give interesting results in electric field profiles and, as a consequence, in density profiles of charged particles.

Inventive design and product development of a mechanical element

The thesis is dedicated to enhancement and development of a Mechanism in Company X in order to increase its key parameters and approve its workability. Current Mechanism model is described in details. The basis of various analysis, models and theories that are reflecting the working process of the Mechanism are included in the thesis. According to these three directions of enhancements are chosen: from mechanical, tribological and conceptual points of view. As the result the list of improvements is presented. The new models of Mechanism are built. The efficiency and lifetime value are obtained in accordance with corresponding estimations. The comparative analysis confirms the necessity of conducted changes. Recommendations for the Company X specialists are represented in the thesis. Proposals for deeper research are also suggested.

Simulation and material calibration of ultra high strength steel (UHSS) S960 welded joint under static tensile test utilizing finite element method (FEM)

The aim of this work was to calibrate the material properties including strength and strain values for different material zones of ultra-high strength steel (UHSS) welded joints under monotonic static loading. The UHSS is heat sensitive and softens by heat due to welding, the affected zone is heat affected zone (HAZ). In this regard, cylindrical specimens were cut out from welded joints of Strenx® 960 MC and Strenx® Tube 960 MH, were examined by tensile test. The hardness values of specimens’ cross section were measured. Using correlations between hardness and strength, initial material properties were obtained. The same size specimen with different zones of material same as real specimen were created and defined in finite element method (FEM) software with commercial brand Abaqus 6.14-1. The loading and boundary conditions were defined considering tensile test values. Using initial material properties made of hardness-strength correlations (true stress-strain values) as Abaqus main input, FEM is utilized to simulate the tensile test process. By comparing FEM Abaqus results with measured results of tensile test, initial material properties will be revised and reused as software input to be fully calibrated in such a way that FEM results and tensile test results deviate minimum. Two type of different S960 were used including 960 MC plates, and structural hollow section 960 MH X-joint. The joint is welded by BöhlerTM X96 filler material. In welded joints, typically the following zones appear: Weld (WEL), Heat affected zone (HAZ) coarse grained (HCG) and fine grained (HFG), annealed zone, and base material (BaM). Results showed that: The HAZ zone is softened due to heat input while welding. For all the specimens, the softened zone’s strength is decreased and makes it a weakest zone where fracture happens while loading. Stress concentration of a notched specimen can represent the properties of notched zone. The load-displacement diagram from FEM modeling matches with the experiments by the calibrated material properties by compromising two correlations of hardness and strength.

Reputational Risk Management as a key element for business continuity and value maximization

This thesis reveals the topic of reputational risk management as a key element for business continuity and value maximization. The purpose of the work is to investigate reputational risk from the side of its definition, management (including legal requirements on this risk category) and measurement and to analyse reputational risk’s impact on business continuity and value maximization. To be able to do this, different respective articles, reports of financial institutions are gathered and constructive summaries and analysis are made. In order to deeply investigate the impact of reputational risk on business continuity and value maximization, it was chosen to study it from three aspects: 1) check the impact of stock valuation of 7 companies that experienced reputational catastrophe / risk, 2) analyse a case study on disagreements in management of reputational risk among case companies and impact on their respective performance, and 3) conduct a survey of financial sector companies in Liechtenstein to see how reputational risk management works in practice. The findings of the research showed a significant impact of reputation decadence on company’s value and trading volume, and showed crucial importance of post-crisis management for the company’s financial performance. The results of the qualitative research based on survey proved that companies consider reputational risk management as a one of the key elements for their business continuity and value maximization.

Peak Force Kelvin Probe Force Microscopy Investigation of ZrO2 Nanocomposites for Hygroelectricity Power Element

ZrO2 nanocomposites were investigated considering their perspective application in hygroelectric power elements. Scanning probe microscopy (SPM) techniques allowed to visualize the surface topography and electrical properties. In this work was compared spacial charge behaviour of sample in humid and dry air conditions. Also different SPM modes were compared. Kelvin probe force microscopy (KPFM) was applied to characterize the spacial charge distribution on surface of the sample. Measurements showed, that trapped charge is not dissipated and can be manipulated with low voltages. Humidity influence on the electric potential of the sample was shown.