Studies on integrating kinematic design method with mechanical systems simulation techniques

Theultimate goal of any research in the mechanism/kinematic/design area may be called predictive design, ie the optimisation of mechanism proportions in the design stage without requiring extensive life and wear testing. This is an ambitious goal and can be realised through development and refinement of numerical (computational) technology in order to facilitate the design analysis and optimisation of complex mechanisms, mechanical components and systems. As a part of the systematic design methodology this thesis concentrates on kinematic synthesis (kinematic design and analysis) methods in the mechanism synthesis process. The main task of kinematic design is to find all possible solutions in the form of structural parameters to accomplish the desired requirements of motion. Main formulations of kinematic design can be broadly divided to exact synthesis and approximate synthesis formulations. The exact synthesis formulation is based in solving n linear or nonlinear equations in n variables and the solutions for the problem areget by adopting closed form classical or modern algebraic solution methods or using numerical solution methods based on the polynomial continuation or homotopy. The approximate synthesis formulations is based on minimising the approximation error by direct optimisation The main drawbacks of exact synthesis formulationare: (ia) limitations of number of design specifications and (iia) failure in handling design constraints- especially inequality constraints. The main drawbacks of approximate synthesis formulations are: (ib) it is difficult to choose a proper initial linkage and (iib) it is hard to find more than one solution. Recentformulations in solving the approximate synthesis problem adopts polynomial continuation providing several solutions, but it can not handle inequality const-raints. Based on the practical design needs the mixed exact-approximate position synthesis with two exact and an unlimited number of approximate positions has also been developed. The solutions space is presented as a ground pivot map but thepole between the exact positions cannot be selected as a ground pivot. In this thesis the exact synthesis problem of planar mechanism is solved by generating all possible solutions for the optimisation process ¿ including solutions in positive dimensional solution sets - within inequality constraints of structural parameters. Through the literature research it is first shown that the algebraic and numerical solution methods ¿ used in the research area of computational kinematics ¿ are capable of solving non-parametric algebraic systems of n equations inn variables and cannot handle the singularities associated with positive-dimensional solution sets. In this thesis the problem of positive-dimensional solutionsets is solved adopting the main principles from mathematical research area of algebraic geometry in solving parametric ( in the mathematical sense that all parameter values are considered ¿ including the degenerate cases ¿ for which the system is solvable ) algebraic systems of n equations and at least n+1 variables.Adopting the developed solution method in solving the dyadic equations in direct polynomial form in two- to three-precision-points it has been algebraically proved and numerically demonstrated that the map of the ground pivots is ambiguousand that the singularities associated with positive-dimensional solution sets can be solved. The positive-dimensional solution sets associated with the poles might contain physically meaningful solutions in the form of optimal defectfree mechanisms. Traditionally the mechanism optimisation of hydraulically driven boommechanisms is done at early state of the design process. This will result in optimal component design rather than optimal system level design. Modern mechanismoptimisation at system level demands integration of kinematic design methods with mechanical system simulation techniques. In this thesis a new kinematic design method for hydraulically driven boom mechanism is developed and integrated in mechanical system simulation techniques. The developed kinematic design method is based on the combinations of two-precision-point formulation and on optimisation ( with mathematical programming techniques or adopting optimisation methods based on probability and statistics ) of substructures using calculated criteria from the system level response of multidegree-of-freedom mechanisms. Eg. by adopting the mixed exact-approximate position synthesis in direct optimisation (using mathematical programming techniques) with two exact positions and an unlimitednumber of approximate positions the drawbacks of (ia)-(iib) has been cancelled.The design principles of the developed method are based on the design-tree -approach of the mechanical systems and the design method ¿ in principle ¿ is capable of capturing the interrelationship between kinematic and dynamic synthesis simultaneously when the developed kinematic design method is integrated with the mechanical system simulation techniques.

FPGA-Based Control Design for Power Electronic Applications

Tehoelektoniikkalaitteella tarkoitetaan ohjaus- ja säätöjärjestelmää, jolla sähköä muokataan saatavilla olevasta muodosta haluttuun uuteen muotoon ja samalla hallitaan sähköisen tehon virtausta lähteestä käyttökohteeseen. Tämä siis eroaa signaalielektroniikasta, jossa sähköllä tyypillisesti siirretään tietoa hyödyntäen eri tiloja. Tehoelektroniikkalaitteita vertailtaessa katsotaan yleensä niiden luotettavuutta, kokoa, tehokkuutta, säätötarkkuutta ja tietysti hintaa. Tyypillisiä tehoelektroniikkalaitteita ovat taajuudenmuuttajat, UPS (Uninterruptible Power Supply) -laitteet, hitsauskoneet, induktiokuumentimet sekä erilaiset teholähteet. Perinteisesti näiden laitteiden ohjaus toteutetaan käyttäen mikroprosessoreja, ASIC- (Application Specific Integrated Circuit) tai IC (Intergrated Circuit) -piirejä sekä analogisia säätimiä. Tässä tutkimuksessa on analysoitu FPGA (Field Programmable Gate Array) -piirien soveltuvuutta tehoelektroniikan ohjaukseen. FPGA-piirien rakenne muodostuu erilaisista loogisista elementeistä ja niiden välisistä yhdysjohdoista.Loogiset elementit ovat porttipiirejä ja kiikkuja. Yhdysjohdot ja loogiset elementit ovat piirissä kiinteitä eikä koostumusta tai lukumäärää voi jälkikäteen muuttaa. Ohjelmoitavuus syntyy elementtien välisistä liitännöistä. Piirissä on lukuisia, jopa miljoonia kytkimiä, joiden asento voidaan asettaa. Siten piirin peruselementeistä voidaan muodostaa lukematon määrä erilaisia toiminnallisia kokonaisuuksia. FPGA-piirejä on pitkään käytetty kommunikointialan tuotteissa ja siksi niiden kehitys on viime vuosina ollut nopeaa. Samalla hinnat ovat pudonneet. Tästä johtuen FPGA-piiristä on tullut kiinnostava vaihtoehto myös tehoelektroniikkalaitteiden ohjaukseen. Väitöstyössä FPGA-piirien käytön soveltuvuutta on tutkittu käyttäen kahta vaativaa ja erilaista käytännön tehoelektroniikkalaitetta: taajuudenmuuttajaa ja hitsauskonetta. Molempiin testikohteisiin rakennettiin alan suomalaisten teollisuusyritysten kanssa soveltuvat prototyypit,joiden ohjauselektroniikka muutettiin FPGA-pohjaiseksi. Lisäksi kehitettiin tätä uutta tekniikkaa hyödyntävät uudentyyppiset ohjausmenetelmät. Prototyyppien toimivuutta verrattiin vastaaviin perinteisillä menetelmillä ohjattuihin kaupallisiin tuotteisiin ja havaittiin FPGA-piirien mahdollistaman rinnakkaisen laskennantuomat edut molempien tehoelektroniikkalaitteiden toimivuudessa. Työssä on myösesitetty uusia menetelmiä ja työkaluja FPGA-pohjaisen säätöjärjestelmän kehitykseen ja testaukseen. Esitetyillä menetelmillä tuotteiden kehitys saadaan mahdollisimman nopeaksi ja tehokkaaksi. Lisäksi työssä on kehitetty FPGA:n sisäinen ohjaus- ja kommunikointiväylärakenne, joka palvelee tehoelektroniikkalaitteiden ohjaussovelluksia. Uusi kommunikointirakenne edistää lisäksi jo tehtyjen osajärjestelmien uudelleen käytettävyyttä tulevissa sovelluksissa ja tuotesukupolvissa.

Cost information in engineering design -Potentials and limitations of activity-based costing

The purpose of this thesis is to analyse activity-based costing (ABC) and possible modified versions ofit in engineering design context. The design engineers need cost information attheir decision-making level and the cost information should also have a strong future orientation. These demands are high because traditional management accounting has concentrated on the direct actual costs of the products. However, cost accounting has progressed as ABC was introduced late 1980s and adopted widely bycompanies in the 1990s. The ABC has been a success, but it has gained also criticism. In some cases the ambitious ABC systems have become too complex to build,use and update. This study can be called an action-oriented case study with some normative features. In this thesis theoretical concepts are assessed and allowed to unfold gradually through interaction with data from three cases. The theoretical starting points are ABC and theory of engineering design process (chapter2). Concepts and research results from these theoretical approaches are summarized in two hypotheses (chapter 2.3). The hypotheses are analysed with two cases (chapter 3). After the two case analyses, the ABC part is extended to cover alsoother modern cost accounting methods, e.g. process costing and feature costing (chapter 4.1). The ideas from this second theoretical part are operationalized with the third case (chapter 4.2). The knowledge from the theory and three cases is summarized in the created framework (chapter 4.3). With the created frameworkit is possible to analyse ABC and its modifications in the engineering design context. The framework collects the factors that guide the choice of the costing method to be used in engineering design. It also illuminates the contents of various ABC-related costing methods. However, the framework needs to be further tested. On the basis of the three cases it can be said that ABC should be used cautiously when formulating cost information for engineering design. It is suitable when the manufacturing can be considered simple, or when the design engineers are not cost conscious, and in the beginning of the design process when doing adaptive or variant design. If the design engineers need cost information for the embodiment or detailed design, or if manufacturing can be considered complex, or when design engineers are cost conscious, the ABC has to be always evaluated critically.

Permanent magnet synchronous motor for industrial inverter applications - analysis and design

During the latest few years the need for new motor types has grown, since both high efficiency and an accurate dynamic performance are demanded in industrial applications. For this reason, new effective control systems such as direct torque control (DTC) have been developed. Permanent magnet synchronous motors (PMSM) are well suitable for new adjustable speed AC inverter drives, because their efficiency and power factor are not depending on the pole pair number and speed to the same extent as it is the case in induction motors. Therefore, an induction motor (IM) with a mechanical gearbox can often be replaced with a direct PM motor drive. Space as well as costs will be saved, because the efficiency increases and the cost of maintenance decreases as well. This thesis deals with design criterion, analytical calculation and analysis of the permanent magnet synchronous motor for both sinusoidal air-gap flux density and rectangular air-gapflux density. It is examined how the air-gap flux, flux densities, inductances and torque can be estimated analytically for salient pole and non-salient pole motors. It has been sought by means of analytical calculations for the ultimate construction for machines rotating at relative low 300 rpm to 600 rpm speeds, which are suitable speeds e.g. in Pulp&Paper industry. The calculations are verified by using Finite Element calculations and by measuring of prototype motor. The prototype motor is a 45 kW, 600 rpm PMSM with buried V-magnets, which is a very appropriate construction for high torque motors with a high performance. With the purposebuilt prototype machine it is possible not only to verify the analytical calculations but also to show whether the 600 rpm PMSM can replace the 1500 rpm IM with a gear. It can also be tested if the outer dimensions of the PMSM may be the same as for the IM and if the PMSM in this case can produce a 2.5 fold torque, in consequence of which it may be possible to achieve the same power. The thesis also considers the question how to design a permanent magnet synchronous motor for relatively low speed applications that require a high motor torqueand efficiency as well as bearable costs of permanent magnet materials. It is shown how a selection of different parameters affects the motor properties. Key words: Permanent magnet synchronous motor, PMSM, surface magnets, buried magnets

Design of axial-flux permanent-magnet low-speed machines and performance comparison between radial-flux and axial-flux machines

This thesis presents an alternative approach to the analytical design of surface-mounted axialflux permanent-magnet machines. Emphasis has been placed on the design of axial-flux machines with a one-rotor-two-stators configuration. The design model developed in this study incorporates facilities to include both the electromagnetic design and thermal design of the machine as well as to take into consideration the complexity of the permanent-magnet shapes, which is a typical requirement for the design of high-performance permanent-magnet motors. A prototype machine with rated 5 kW output power at 300 min-1 rotation speed has been designed and constructed for the purposesof ascertaining the results obtained from the analytical design model. A comparative study of low-speed axial-flux and low-speed radial-flux permanent-magnet machines is presented. The comparative study concentrates on 55 kW machines with rotation speeds 150 min-1, 300 min-1 and 600 min-1 and is based on calculated designs. A novel comparison method is introduced. The method takes into account the mechanical constraints of the machine and enables comparison of the designed machines, with respect to the volume, efficiency and cost aspects of each machine. It is shown that an axial-flux permanent-magnet machine with one-rotor-two-stators configuration has generally a weaker efficiency than a radial-flux permanent-magnet machine if for all designs the same electric loading, air-gap flux density and current density have been applied. On the other hand, axial-flux machines are usually smaller in volume, especially when compared to radial-flux machines for which the length ratio (axial length of stator stack vs. air-gap diameter)is below 0.5. The comparison results show also that radial-flux machines with alow number of pole pairs, p < 4, outperform the corresponding axial-flux machines.

Welding time models for cost calculations in the early stages of the design process

It is generally accepted that between 70 and 80% of manufacturing costs can be attributed to design. Nevertheless, it is difficult for the designer to estimate manufacturing costs accurately, especially when alternative constructions are compared at the conceptual design phase, because of the lack of cost information and appropriate tools. In general, previous reports concerning optimisation of a welded structure have used the mass of the product as the basis for the cost comparison. However, it can easily be shown using a simple example that the use of product mass as the sole manufacturing cost estimator is unsatisfactory. This study describes a method of formulating welding time models for cost calculation, and presents the results of the models for particular sections, based on typical costs in Finland. This was achieved by collecting information concerning welded products from different companies. The data included 71 different welded assemblies taken from the mechanical engineering and construction industries. The welded assemblies contained in total 1 589 welded parts, 4 257 separate welds, and a total welded length of 3 188 metres. The data were modelled for statistical calculations, and models of welding time were derived by using linear regression analysis. Themodels were tested by using appropriate statistical methods, and were found to be accurate. General welding time models have been developed, valid for welding in Finland, as well as specific, more accurate models for particular companies. The models are presented in such a form that they can be used easily by a designer, enabling the cost calculation to be automated.

Tuning the design procedures for laser processed microwave mechanics

This research has been focused at the development of a tuned systematic design methodology, which gives the best performance in a computer aided environment and utilises a cross-technological approach, specially tested with and for laser processed microwave mechanics. A tuned design process scheme is also presented. Because of the currently large production volumes of microwave and radio frequency mechanics even slight improvements of design methodologies or manufacturing technologies would give reasonable possibilities for cost reduction. The typical number of required iteration cycles could be reduced to one fifth of normal. The research area dealing with the methodologies is divided firstly into a function-oriented, a performance-oriented or a manufacturability-oriented product design. Alternatively various approaches can be developed for a customer-oriented, a quality-oriented, a cost-oriented or an organisation-oriented design. However, the real need for improvements is between these two extremes. This means that the effective methodology for the designers should not be too limited (like in the performance-oriented design) or too general (like in the organisation-oriented design), but it should, include the context of the design environment. This is the area where the current research is focused. To test the developed tuned design methodology for laser processing (TDMLP) and the tuned optimising algorithm for laser processing (TOLP), seven different industrial product applications for microwave mechanics have been designed, CAD-modelled and manufactured by using laser in small production series. To verify that the performance of these products meets the required level and to ensure the objectiveness ofthe results extensive laboratory tests were used for all designed prototypes. As an example a Ku-band horn antenna can be laser processed from steel in 2 minutes at the same time obtaining a comparable electrical performance of classical aluminium units or the residual resistance of a laser joint in steel could be limited to 72 milliohmia.

Careers of Managers, Comparison between ICT and Paper Business Sectors

The purpose of this study is to increase understanding of how the managers build their early career in information and communication technology industry (ICT business sector) and pulp- and paper industry (paper business sector). The focus of the study is to explore the importance differing a business sectors have in influencing managerial careers. Business sectors can affect careers in several ways.Sectors have different history and traditions. Also the age structure of ICT personnel differs from the age structure of personnel in the paper industry. Managers in the ICT and paper sector are technically educated but in different disciplines. Differences exist also in ways of recruiting and developing commitment inpersonnel. The target group of this research, middle management engineering personnel, work in Finnish ICT and paper companies. Research data were gathered in April-December 2002 in South-Karelia by interviewing 30 managers and six directors working in three Finnish ICT companies and in three paper companies. The research issue is approached on two levels: the individual level and the organizational level. The managers related their career stories in focused interviews. Directors, representing the organizations, described the generalities of the business sector and gave background information on company policies, human relationshippractices, as well as career and human resource development. Results of the study contribute to research discussions of career, life-span reasoning, socialization and commitment. Career is conceived as a series of positions including everykind of hierarchical mobility and all kinds of positions in work. A manager's career develops in interaction with the organization and it can be seen as involving a socializing process in an organization as a consequence of experiences andchanges in positions. This research contributes to the understanding of the nature of career in the context of two business sectors. Universal career theories,for the most part, do not perceive the importance of business sector in determining career experience. This study concentrates on describing and understanding early careers in two different business areas, elements committing managers to particular business sectors and the actions of companies in that particular sector. While career research began in the middle of 1950s, the theoretical basis of career research seems to be quite fragmented still. However, a dichotomy is consistently presented between traditional, hierarchical career research and boundaryless career thinking. In this research we examine how these old and new career concepts are evidence in the ICT and paper sectors. Careers are changing from formal, hierarchy-based structures to more fluid arrangements. The new boundaryless career concept captures territory from old career thinking. Mobility between employers, networks, and changing hierarchical structures in organizations, as well as personal and family reasons are theorized to bring changes to careers patterns in the future. However, the pace of this change in careers will vary between the ICT and paper business sectors. Findings of this research indicate that business sector has an effect on how managerial careers develop. The environment where career is developed differs between ICT and paper sectors. Careers begin differently in the two environments and the speed of career progression is distinct. ICT careers are built within the business sector whereas paper careers are made inside one company. Also recruiting and socialization practices differ from one sector to the other.

Design and implementation of FPGA-based LQ control of active magnetic bearings

The need for high performance, high precision, and energy saving in rotating machinery demands an alternative solution to traditional bearings. Because of the contactless operation principle, the rotating machines employing active magnetic bearings (AMBs) provide many advantages over the traditional ones. The advantages such as contamination-free operation, low maintenance costs, high rotational speeds, low parasitic losses, programmable stiffness and damping, and vibration insulation come at expense of high cost, and complex technical solution. All these properties make the use of AMBs appropriate primarily for specific and highly demanding applications. High performance and high precision control requires model-based control methods and accurate models of the flexible rotor. In turn, complex models lead to high-order controllers and feature considerable computational burden. Fortunately, in the last few years the advancements in signal processing devices provide new perspective on the real-time control of AMBs. The design and the real-time digital implementation of the high-order LQ controllers, which focus on fast execution times, are the subjects of this work. In particular, the control design and implementation in the field programmable gate array (FPGA) circuits are investigated. The optimal design is guided by the physical constraints of the system for selecting the optimal weighting matrices. The plant model is complemented by augmenting appropriate disturbance models. The compensation of the force-field nonlinearities is proposed for decreasing the uncertainty of the actuator. A disturbance-observer-based unbalance compensation for canceling the magnetic force vibrations or vibrations in the measured positions is presented. The theoretical studies are verified by the practical experiments utilizing a custom-built laboratory test rig. The test rig uses a prototyping control platform developed in the scope of this work. To sum up, the work makes a step in the direction of an embedded single-chip FPGA-based controller of AMBs.

Design,implementation and use of an Internet kiosk as an an information system for CNC machinists

Tätä diplomityötä sponsoroi suuri Isobritannialainen lentokoneteollisuudessa toimiva yritys, joka huomasi että globaalin tuotantostrategian ollessa painopisteenä ja tietoteknisten järjestelmien kuten CAD/CAM ollessa merkittävänä osana tuotantoa, on löydettävä ymmärrys siitä, mitkä ovat tuotannon tietojärjestelmien tarpeet ja onko niiden kehittämisestä hyötyä yritykselle.Diplomityössä selitetään Internet teknologiaan perustuvan kioskin kehittämisestä tietotukijärjestelmäksi tuotanto-osastolle, jossa valmistetaan moottorin osia CNC-koneilla. Kioskeissa on piirteitä, jotka voisivat osoittautua hyödyllisiksi myös tuotantoympäristöissä ja siksi tässä työssä tutkitaan kioskiin perustuvaa lähestymistapaa tuotantoympäristöön sovellettuna.Diplomityö kuvaa informaatiokioskin kehittämistä alkaen alkuvaatimusten keruusta tietojärjestelmää varten, tietojärjestelmän suunnittelu- ja kehitysvaiheen sekä lopuksi analysoi kioskin onnistuneisuutta tuotantoympäristössä käytettävyystutkimuksen avulla, joka suoritettiin sen jälkeen kun kioski oli implementoitu tehtaassa.Johtopäätökset osoittavat, että kioski on hyvin implementoitavissa tuotantoympäristöön ja todistaa, että tuotantoinformaation jakelu sähköisessä muodossa on huomattavasti tehokkaampaa kuin paperilla. Käyttäjien kommentit osoittavat että kioski on sopiva heidän tietotarpeisiinsa ja siitä on hyötyä heidän työlleen. Kioski tarjoaa hyötyjä tuotantotason lisäksi myös johtotasolle.

Comparison of Compound Lean Nozzles and Controlled Flow Nozzles at Off-Design

Turbokoneet ja etenkin höyryturbiinit ovat usein suunniteltu ja optimoitu toimimaan tietyssä toimintapisteessä jossa häviöt on minimoitu ja hyötysuhde maksimoitu. Joissakin tapauksissa on kuitenkin tarpeellista käyttää turbiinia toimintapisteen ulkopuolella. Tällöin turbiinin läpi virtaava massavirta muuttuu ja yleensä heikentää hyötysuhdetta. Turbokoneiden suorituskykyä voidaan parantaa käyttämällä kolmidimensionaalisesti muotoiltuja siipiä. Työssä on vertailtu laskennallisesti kahta kohtuullisesti muotoiltua suutinta (Compound lean ja Controlled flow) niiden suunnitellun toimintapisteen ulkopuolella. Kolmas suutin, ilman kolmidimensionaalista muotoilua on mukana vertailukohteena. Suutinten suorituskykyä tutkitaan laskennallisen virtausmekaniikan avulla olosuhteissa, jotka ovat toimintapisteen ulkopuolella. Virtauksen muutoksia tutkitaan kokonaispainehäviön, isentrooppisen hyötysuhteen ja virtauspinnan yhdenmukaisuuden avulla. Virtauspintoja verrataan ulosvirtauskulman, massavirran ja toisiovirtausvektoreiden jakauman avulla. Erot suutinten suorituskykyvyssä korostavat ylikuormalla. Kun massavirran arvoa on kohotettu eniten, Compound lean suuttimilla hyötysuhde laskee Controlled flow suuttimeen verrattuna vähemmän. Alikuormalla, kun massavirran arvoa lasketaan, erot suuttimien suorituskyvyssä pienenevät ja tutkittujen suuttimien ulosvirtaus on samankaltainen.

Code Generator for Key Management Protocols - Design and Implementation

Key management has a fundamental role in secure communications. Designing and testing of key management protocols is tricky. These protocols must work flawlessly despite of any abuse. The main objective of this work was to design and implement a tool that helps to specify the protocol and makes it possible to test the protocol while it is still under development. This tool generates compile-ready java code from a key management protocol model. A modelling method for these protocols, which uses Unified Modeling Language (UML) was also developed. The protocol is modelled, exported as an XMI and read by the code generator tool. The code generator generates java code that is immediately executable with a test software after compilation.

The design and implementation of a standards-based mobile messaging platform - case WAP Push Proxy Gateway

Tässä diplomityössä perehdytään WAP:in Push -viitekehykseen. WAP-standardit määrittelevät kuinka Internet-tyyppisiä palveluita, joita voidaan käyttää erilaisia mobiileja päätelaiteitteita käyttäen, toteutetaan tehokkaalla ja verkkoteknologiasta riippumattomalla tavalla. WAP pohjautuu Internet:iin, mutta huomioi pienten päätelaitteiden ja mobiiliverkkojen rajoitukset ja erikoisominaisuudet. WAP Push viitekehys määrittelee verkon aloittaman palvelusisällön toimittamisen. Työn teoriaosassa käydään läpi yleinen WAP-arkkitehtuuri ja WAP-protokollapino käyttäen vertailukohtina lanka-Internetin arkkitehtuuria ja protokollapinoa. Edellistä perustana käyttäen tutustaan WAP Push -viitekehykseen. Käytännönosassa kuvataan WAP Push -välityspalvelimen suunnittelu ja kehitystyö. WAP Push -välityspalvelin on keskeinen verkkoelementti WAP Push -viitekehyksessä. WAP Push -välityspalvelin yhdistää Internetin ja mobiiliverkon tavalla, joka piilottaa teknologiaeroavaisuudet Internetissä olevalta palveluntuottajalta.

Network Device Driver Design and Implementation for Symbian Operating System

Tämä diplomityö esittää Symbianin käyttöjärjestelmän verkkoarkkitehtuuriin perustuvan paikallisverkkokortin (LAN) käyttöönottoa. Pääajatus oli keskitetty langattoman LAN— kortin (WLAN) ajureiden käyttöönottoon. Jokainen Symbianin käyttöjärjestelmän verkkoarkkitehtuurin komponentti oli huolellisesti tutkittu, painottaen mahdollista langattoman yhteyden uudelleenkäyttöä. Myös olemassaolevan Ethernetkortin ajureiden uudelleenkäyttö oli huolellisesti otettu huomioon. Diplomityöprojektin aikana esimerkki WLAN-kortin ajurin lähdekoodista oli esitetty. Tämä ajuri on kirjoitettu NOKIA DTN-20 WLAN-korttia varten. Havaittiin myös, että suurin osa Symbianin käyttöjärjestelmän verkkoarkkitehtuurista voidaan käyttää myös WLAN-pohjaisessa yhteydessä ilman muutoksia.. Esitetty ajuri käyttää myös tiettyjä olemassaolevan Ethernetkortin ajureita, esim. Logical Device Driver (LDD):tä.

THE IMPACT OF ARCHITECTURAL DESIGN ON SOFTWARE DEVELOPMENT

Tässä työssä tutkitaan ohjelmistoarkkitehtuurisuunnitteluominaisuuksien vaikutusta erään client-server –arkkitehtuuriin perustuvan mobiilipalvelusovelluksen suunnittelu- ja toteutusaikaan. Kyseinen tutkimus perustuu reaalielämän projektiin, jonka kvalitatiivinen analyysi paljasti arkkitehtuurikompponenttien välisten kytkentöjen merkittävästi vaikuttavan projektin työmäärään. Työn päätavoite oli kvantitatiivisesti tutkia yllä mainitun havainnon oikeellisuus. Tavoitteen saavuttamiseksi suunniteltiin ohjelmistoarkkitehtuurisuunnittelun mittaristo kuvaamaan kyseisen järjestelmän alijärjestelmien arkkitehtuuria ja luotiin kaksi suunniteltua mittaristoa käyttävää, työmäärää (komponentin suunnittelu-, toteutus- ja testausaikojen summa) arvioivaa mallia, joista toinen on lineaarinen ja toinen epälineaarinen. Näiden mallien kertoimet sovitettiin optimoimalla niiden arvot epälineaarista gloobaalioptimointimenetelmää, differentiaalievoluutioalgoritmia, käyttäen, niin että mallien antamat arvot vastasivat parhaiten mitattua työmäärää sekä kaikilla ominaisuuksilla eli attribuuteilla että vain osalla niistä (yksi jätettiin vuorotellen pois). Kun arkkitehtuurikompenttien väliset kytkennät jätettiin malleista pois, mitattujen ja arvoitujen työmäärien välinen ero (ilmaistuna virheenä) kasvoi eräässä tapauksessa 367 % entisestä tarkoittaen sitä, että näin muodostettu malli vastasi toteutusaikoja huonosti annetulla ainestolla. Tämä oli suurin havaitu virhe kaikkien poisjätettyjen ominaisuuksien kesken. Saadun tuloksen perusteella päätettiin, että kyseisen järjestelmän toteutusajat ovat vahvasti riippuvaisia kytkentöjen määrästä, ja näin ollen kytkentöjen määrä oli mitä todennäköisemmin kaikista tärkein työmäärään vaikuttava tekijä tutkitun järjestelmän arkkitehtuurisuunnittelussa.