Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Development of laboratory exercises for basic nuclear thermal hydraulics measurements

The thesis focuses on light water reactors (pressurized water reactors, boiling water reactors) and measurement techniques for basic thermal hydraulics parameters that are used in a nuclear power plant. The goal of this work is a development of laboratory exercises for basic nuclear thermal hydraulics measurements.

Implementation of educational change in Finland: The case of the undivided basic education reform

For the past decades, educational large-scale reforms have been elaborated and implemented in many countries and often resulted in partial or complete failure. These results brought researchers to study policy processes in order to address this particular challenge. Studies on implementation processes brought to light an existing causal relationship between the implementation process and the effectiveness of a reform. This study aims to describe the implementation process of educational change in Finland, who produced efficient educational reforms over the last 50 years. The case study used for the purpose of this study is the national reform of undivided basic education (yhtenäinen peruskoulu) implemented in the end of the 1990s. Therefore, this research aims to describe how the Finnish undivided basic education reform was implemented. This research was carried out using a pluralist and structuralist approach of policy process and was analyzed according to the hybrid model of implementation process. The data were collected using a triangulation of methods, i.e. documentary research, interviews and questionnaires. The data were qualitative and were analyzed using content analysis methods. This study concludes that the undivided basic education reform was applied in a very decentralized manner, which is a reflection of the decentralized system present in Finland. Central authorities provided a clear vision of the purpose of the reform, but did not control the implementation process. They rather provided extensive support in the form of transmission of information and development of collaborative networks. Local authorities had complete autonomy in terms of decision-making and implementation process. Discussions, debates and decisions regarding implementation processes took place at the local level and included the participation of all actors present on the field. Implementation methods differ from a region to another, with is the consequence of the variation of the level of commitment of local actors but also the diversity of local realities. The reform was implemented according to existing structures and values, which means that it was in cohesion with the context in which it was implemented. These results cannot be generalized to all implementation processes of educational change in Finland but give a great insight of what could be the model used in Finland. Future studies could intent to confirm the model described here by studying other reforms that took place in Finland.

Implementation of educational change in Finland: The case of the undivided basic education reform

For the past decades, educational large-scale reforms have been elaborated and implemented in many countries and often resulted in partial or complete failure. These results brought researchers to study policy processes in order to address this particular challenge. Studies on implementation processes brought to light an existing causal relationship between the implementation process and the effectiveness of a reform. This study aims to describe the implementation process of educational change in Finland, who produced efficient educational reforms over the last 50 years. The case study used for the purpose of this study is the national reform of undivided basic education (yhtenäinen peruskoulu) implemented in the end of the 1990s. Therefore, this research aims to describe how the Finnish undivided basic education reform was implemented. This research was carried out using a pluralist and structuralist approach of policy process and was analyzed according to the hybrid model of implementation process. The data were collected using a triangulation of methods, i.e. documentary research, interviews and questionnaires. The data were qualitative and were analyzed using content analysis methods. This study concludes that the undivided basic education reform was applied in a very decentralized manner, which is a reflection of the decentralized system present in Finland. Central authorities provided a clear vision of the purpose of the reform, but did not control the implementation process. They rather provided extensive support in the form of transmission of information and development of collaborative networks. Local authorities had complete autonomy in terms of decision-making and implementation process. Discussions, debates and decisions regarding implementation processes took place at the local level and included the participation of all actors present on the field. Implementation methods differ from a region to another, with is the consequence of the variation of the level of commitment of local actors but also the diversity of local realities. The reform was implemented according to existing structures and values, which means that it was in cohesion with the context in which it was implemented. These results cannot be generalized to all implementation processes of educational change in Finland but give a great insight of what could be the model used in Finland. Future studies could intent to confirm the model described here by studying other reforms that took place in Finland.