The Role of Surfactant Properties of Extractants in Hydrometallurgical LiquidLiquid Extraction Processes

The amphiphilic nature of metal extractants causes the formation of micelles and other microscopic aggregates when in contact with water and an organic diluent. These phenomena and their effects on metal extraction were studied using carboxylic acid (Versatic 10) and organophosphorus acid (Cyanex 272) based extractants. Special emphasis was laid on the study of phase behaviour in a pre neutralisation stage when the extractant is transformed to a sodium or ammonium salt form. The pre neutralised extractants were used to extract nickel and to separate cobalt and nickel. Phase diagrams corresponding to the pre neutralisation stage in a metal extraction process were determined. The maximal solubilisation of the components in the system water(NH3)/extractant/isooctane takes place when the molar ratio between the ammonia salt form and the free form of the extractant is 0.5 for the carboxylic acid and 1 for the organophosphorus acid extractant. These values correspond to the complex stoichiometry of NH4A•HA and NIi4A, respectively. When such a solution is contacted with water a microemulsion is formed. If the aqueous phase contains also metal ions (e.g. Ni²+), complexation will take place on the microscopic interface of the micellar aggregates. Experimental evidence showing that the initial stage of nickel extraction with pre neutralised Versatic 10 is a fast pseudohomogeneous reaction was obtained. About 90% of the metal were extracted in the first 15 s after the initial contact. For nickel extraction with pre neutralised Versatic 10 it was found that the highest metal loading and the lowest residual ammonia and water contents in the organic phase are achieved when the feeds are balanced so that the stoichiometry is 2NH4+(org) = Nit2+(aq). In the case of Co/Ni separation using pre neutralised Cyanex 272 the highest separation is achieved when the Co/extractant molar ratio in the feeds is 1 : 4 and at the same time the optimal degree of neutralisation of the Cyanex 272 is about 50%. The adsorption of the extractants on solid surfaces may cause accumulation of solid fine particles at the interface between the aqueous and organic phases in metal extraction processes. Copper extraction processes are known to suffer of this problem. Experiments were carried out using model silica and mica particles. It was found that high copper loading, aromacity of the diluent, modification agents and the presence of aqueous phase decrease the adsorption of the hydroxyoxime on silica surfaces.

Structural studies on enzymes of biotechnological and biomedical interest

Structural studies of proteins aim at elucidating the atomic details of molecular interactions in biological processes of living organisms. These studies are particularly important in understanding structure, function and evolution of proteins and in defining their roles in complex biological settings. Furthermore, structural studies can be used for the development of novel properties in biomolecules of environmental, industrial and medical importance. X-ray crystallography is an invaluable tool to obtain accurate and precise information about the structure of proteins at the atomic level. Glutathione transferases (GSTs) are amongst the most versatile enzymes in nature. They are able to catalyze a wide variety of conjugation reactions between glutathione (GSH) and non-polar components containing an electrophilic carbon, nitrogen or sulphur atom. Plant GSTs from the Tau class (a poorly characterized class) play an important role in the detoxification of xenobiotics and stress tolerance. Structural studies were performed on a Tau class fluorodifen-inducible glutathione transferase from Glycine max (GmGSTU4-4) complexed with GSH (2.7 Å) and a product analogue Nb-GSH (1.7 Å). The three-dimensional structure of the GmGSTU4-4-GSH complex revealed that GSH binds in different conformations in the two subunits of the dimer: in an ionized form in one subunit and a non-ionized form in the second subunit. Only the ionized form of the substrate may lead to the formation of a catalytically competent complex. Structural comparison between the GSH and Nb-GSH bound complexes revealed significant differences with respect to the hydrogen-bonding, electrostatic interaction pattern, the upper part of -helix H4 and the C-terminus of the enzyme. These differences indicate an intrasubunit modulation between the G-and Hsites suggesting an induced-fit mechanism of xenobiotic substrate binding. A novel binding site on the surface of the enzyme was also revealed. Bacterial type-II L-asparaginases are used in the treatment of haematopoietic diseases such as acute lymphoblastic leukaemia (ALL) and lymphomas due to their ability to catalyze the conversion of L-asparagine to L-aspartate and ammonia. Escherichia coli and Erwinia chrysanthemi asparaginases are employed for the treatment of ALL for over 30 years. However, serious side-effects affecting the liver and pancreas have been observed due to the intrinsic glutaminase activity of the administered enzymes. Structural studies on Helicobacter pylori L-asparaginase (HpA) were carried out in an effort to discover novel L-asparaginases with potential chemotherapeutic utility in ALL treatment. Detailed analysis of the active site geometry revealed structurally significant differences between HpA and other Lasparaginases that may be important for the biological activities of the enzyme and could be further exploited in protein engineering efforts.

The Sottunga-Jurmo shear zone : structure and deformation history of a crustal-scale ductile shear zone in SW Finland

The aim of this study is to gain a better understanding of the structure and the deformation history of a NW-SE trending regional, crustal-scale shear structure in the Åland archipelago, SW Finland, called the Sottunga-Jurmo shear zone (SJSZ). Approaches involving e.g. structural geology, geochronology, geochemistry and metamorphic petrology were utilised in order to reconstruct the overall deformation history of the study area. The study therefore describes several features of the shear zone including structures, kinematics and lithologies within the study area, the ages of the different deformation phases (ductile to brittle) within the shear zone, as well as some geothermobarometric results. The results indicate that the SJSZ outlines a major crustal discontinuity between the extensively migmatized rocks NE of the shear zone and the unmigmatised, amphibolite facies rocks SW of the zone. The main SJSZ shows overall dextral lateral kinematics with a SW-side up vertical component and deformation partitioning into pure shear and simple shear dominated deformation styles that was intensified toward later stages of the deformation history. The deformation partitioning resulted in complex folding and refolding against the SW margin of the SJSZ, including conical and sheath folds, and in a formation of several minor strike-slip shear zones both parallel and conjugate to the main SJSZ in order to accommodate the regional transpressive stresses. Different deformation phases within the study area were dated by SIMS (zircon U-Pb), ID-TIMS (titanite U-Pb) and 40Ar/39Ar (pseudotachylyte wholerock) methods. The first deformation phase within the ca. 1.88 Ga rocks of the study area is dated at ca. 1.85 Ga, and the shear zone was reactivated twice within the ductile regime (at ca. 1.83 Ga and 1.79 Ga), during which the strain was successively increasingly partitioned into the main SJSZ and the minor shear zones. The age determinations suggest that the orogenic processes within the study area did not occur in a temporal continuum; instead, the metamorphic zircon rims and titanites show distinct, 10-20 Ma long breaks in deformation between phases of active deformation. The results of this study further imply slow cooling of the rocks through 600-700ºC so that at 1.79 Ga, 2 the temperature was still at least 600ºC. The highest recorded metamorphic pressures are 6.4-7.1 kbar. At the late stages or soon after the last ductile phase (ca. 1.79 Ga), relatively high-T mylonites and ultramylonites were formed, witnessing extreme deformation partitioning and high strain rates. After the rocks reached lower amphibolite facies to amphibolite-greenschist facies transitional conditions (ca. 500-550ºC), they cooled rapidly, probably due to crustal uplift and exhumation. The shear zone was reactivated at least once within the semi-brittle to brittle regime between ca. 1.79 Ga and 1.58 Ga, as evidenced by cataclasites and pseudotachylytes. In summary, the results of this study suggest that the Sottunga-Jurmo shear zone (and the South Finland shear zone) defines a major crustal discontinuity, and played a central role in accommodating the regional stresses during and after the Svecofennian orogeny.

Enhancing performance of paper coatings by tailor-made plastic pigments

The paper industry is constantly looking for new ideas for improving paper products while competition and raw material prices are increasing. Many paper products are pigment coated. Coating layer is the top layer of paper, thus by modifying coating pigment also the paper itself can be altered and value added to the final product. In this thesis, synthesis of new plastic and hybrid pigments and their performance in paper and paperboard coating is reported. Two types of plastic pigments were studied: core-shell latexes and solid beads of maleimide copolymers. Core-shell latexes with partially crosslinked hydrophilic polymer core of poly(n-butyl acrylate-co-methacrylic acid) and a hard hydrophobic polystyrene shell were prepared to improve the optical properties of coated paper. In addition, the effect of different crosslinkers was analyzed and the best overall performance was achieved by the use of ethylene glycol dimethacrylate (EGDMA). Furthermore, the possibility to modify core-shell latex was investigated by introducing a new polymerizable optical brightening agent, 1-[(4-vinylphenoxy)methyl]-4-(2-henylethylenyl)benzene which gave promising results. The prepared core-shell latex pigments performed smoothly also in pilot coating and printing trials. The results demonstrated that by optimizing polymer composition, the optical and surface properties of coated paper can be significantly enhanced. The optimal reaction conditions were established for thermal imidization of poly(styrene-co-maleimide) (SMI) and poly(octadecene-co-maleimide) (OMI) from respective maleic anhydride copolymer precursors and ammonia in a solvent free process. The obtained aqueous dispersions of nanoparticle copolymers exhibited glass transition temperatures (Tg) between 140-170ºC and particle sizes from 50-230 nm. Furthermore, the maleimide copolymers were evaluated in paperboard coating as additional pigments. The maleimide copolymer nanoparticles were partly imbedded into the porous coating structure and therefore the full potential of optical property enhancement for paperboard was not achieved by this method. The possibility to modify maleimide copolymers was also studied. Modifications were carried out via N-substitution by replacing part of the ammonia in the imidization reaction with amines, such as triacetonediamine (TAD), aspartic acid (ASP) and fluorinated amines (2,2,2- trifluoroethylamine, TFEA and 2,2,3,3,4,4,4-heptafluorobuthylamine, HFBA). The obtained functional nanoparticles varied in size between 50-217 nm and their Tg from 150-180ºC. During the coating process the produced plastic pigments exhibited good runnability. No significant improvements were achieved in light stability with TAD modified copolymers whereas nanoparticles modified with aspartic acid and those containing fluorinated groups showed the desired changes in surface properties of the coated paperboard. Finally, reports on preliminary studies with organic-inorganic hybrids are presented. The hybrids prepared by an in situ polymerization reaction consisted of 30 wt% poly(styrene- co-maleimide) (SMI) and high levels of 70 wt% inorganic components of kaolin and/or alumina trihydrate. Scanning Electron Microscopy (SEM) images and characterization by Fourier Transform Infrared Spcetroscopy (FTIR) and X-Ray Diffraction (XRD) revealed that the hybrids had conventional composite structure and inorganic components were covered with precipitated SMI nanoparticles attached to the surface via hydrogen bonding. In paper coating, the hybrids had a beneficial effect on increasing gloss levels.

Jätteenpolton typenoksidipäästöjen vähentäminen

Työn tavoitteena oli selvittää jätteenpolton typenoksidipäästöjen puhdistusmahdollisuuksia. Työssä käydään läpi typen oksidien muodostuminen poltossa ja typen oksidien poistomenetelmät. Poistomenetelmiä käsiteltäessä painotus on arinapoltossa ja erityisesti selektiivisessä ei-katalyyttimenetelmässä (SNCR). Työn kokeellinen osa tehtiin Ekokem Oy Ab:n jätevoimalassa Riihimäellä. Kokeellisessa osassa selvitettiin ensin ammoniakkiveden massavirran, SNCR-laitteiston veden massavirran ja räjähdysnuohouksen vaikutusta typenoksidipitoisuuteen. Samalla selvitettiin muita typenoksidipitoisuuteen vaikuttavia tekijöitä sekä SNCR-laitteiston puhdistustehokkuus. Sen jälkeen selvitettiin parhaita toiminta-arvoja öljyisen veden massavirralle, SNCR-laitteiston massavirralle ja primääri- ja sekundääri-ilman suhteelle typenoksidipitoisuuden, ammoniakki-slip:n, ilokaasupitoisuuden, ammoniakkiveden kulutuksen ja höyryn tuotannon kannalta. Tulokseksi saatiin, että ammoniakkiveden massavirran lisääminen pienentää typenoksidipitoisuutta, mutta voi aiheuttaa ammoniakkipäästön. Paras SNCR-laitteiston veden massavirta on suurin tutkittu, 800 kg/h, jolloin typenoksidipitoisuus sekä typenoksidipitoisuuden hetkittäinen vaihtelu, ammoniakkiveden kulutus ja ammoniakkipäästö ovat pienimmät. Samalla tosin höyryn virtaama pienenee. SNCR-laitteiston puhdistustehokkuudeksi saatiin 60 %. Räjähdysnuohouksella ei ole havaittavaa, eikä öljyisen veden massavirralla merkittävää vaikutusta typenoksidipitoisuuteen. Ammoniakkiveden kulutuksen kannalta paras öljyisen veden määrä on 600 kg/h, kun taas ammoniakki-slip:n kannalta paras öljyisen veden määrä on 950 kg/h. Primääri-ilman osuuden pienentäminen pienentää ammoniakki-slip:iä ja ammoniakkiveden kulutusta.

Ammoniumkloridi Porvoon ja Naantalin jalostamoiden vetyverkoissa

Tässä työssä on käsitelty ammoniumkloridia Porvoon ja Naantalin jalostamoiden vetyverkoissa. Tietoa ammoniumkloridin aiheuttamista ongelmista ja niihin vaikuttavista tekijöistä on kerätty ja niiden pohjalta on pyritty löytämään keinoja, joilla ongelmaa voidaan vähentää tai poistaa. Kirjallisuusosassa on käsitelty ammoniumkloridia, sen aiheuttamaa korroosiota ja materiaalien ammoniumkloridikestävyyttä. Lisäksi kirjallisuusosassa on käsitelty ammoniumkloridin muodostumiseen tarvittavan vetykloridin määritysmenetelmiä sekä ammonium- ja kloridi-ionien määritysmenetelmiä. Työn soveltavassa osassa kerättiin tietoa ammoniumkloridin aiheuttamista ongelmista ja ammoniumkloridin muodostumiseen vaikuttavista tekijöistä. Lisäksi Porvoon jalostamolla suoritettiin mittauksia, joilla määritettiin ammoniakki- ja vetykloridipitoisuuksia vetyvirroista. Tulosten perusteella saatiin käsitys jalostamon ammoniumkloridiongelman nykytilanteesta ja tutkittiin ammoniumkloridia muodostavien ammoniakin ja vetykloridin lähteitä. Lisäksi keinoja vähentää ammoniumkloridin muodostumista tunnistettiin.

Lämpöpumppujärjestelmät integroidussa kylmä- ja lämpötehon tuotossa

Tässä työssä tutkittiin lämpöpumppujärjestelmiä, joilla tuotetaan samaan aikaan kylmä- ja lämpötehoa. Höyryn puristus lämpöpumppu on yleisimmin käytetty lämpöpumpputyyppi ja sen pääkomponentit ovat kompressori, lauhdutin, paisuntaventtiili ja höyrystin. Lämpöpumppu tuottaa samaan aikaan kylmätehoa höyrystimellä ja lämpötehoa lauhduttimella. Lämpöpumpun toiminta-arvoihin vaikuttaa valittujen lämpötilatasojen lisäksi voimakkaasti valitun kiertoaineen termodynaamiset ominaisuudet sekä kompressorin painesuhteeseen verrannollinen isentrooppihyötysuhde. Uusissa lämpöpumpuissa käytetään HFC yhdisteitä sekä sekoituksia kiertoaineina, mutta myös luonnolliset aineet, kuten ammoniakki, ovat lupaavia korvikkeita CFC yhdisteille. Sopivia sovelluskohteita kylmä- ja lämpötehon yhteistuotannolle ovat kauppa- ja asuinrakennukset, hotellit, toimistot, elintarviketeollisuus ja -myymälät sekä vierekkäiset jää- ja uimahallit ja hiihtoputket. Kylmä- ja lämpötehon yhteistuotannolla voitaisiin saavuttaa merkittäviä säästöjä ja päästövähennyksiä. Esimerkiksi jäähallien kylmäkoneiden lauhdelämmön hyödyntämisessä olisi Suomessa potentiaalia 6-10 miljoonan euron vuotuisiin säästöihin. Kylmä- ja lämpötehon yhteistuotanto voidaan toteuttaa hyödyntämällä kylmäkoneen lauhdelämpöä toisella lämpöpumpulla. Toinen vaihtoehto on käyttää eri tilojen samanaikaiseen lämmittämiseen ja jäähdyttämiseen HPS lämpöpumppua tai moniyksikköistä lämpöpumppua.

Lannoitetehtaan prosessivesien käsittelyvaihtoehtojen soveltuvuuden arviointi

Phosphorus and nitrogen cause eutrophication of water bodies, causing severe damage to the ecosystem. Eutrophication of the waters causes oxygen depletion, which in turn increases fish mortality, releasing toxins in waters. The released toxins can cause damage to animals and humans, which is the reason in many countries to set emission limits for waste water. Nutrients exist naturally, but due to human activities there is high nutrient leaching to water bodies. Human activity is one of the main reasons to the eutrophication. The aim of this thesis was to estimate the suitability of different water treatment options for Yara Finland’s fertilizer plant’s process waters in Siilinjärvi. The fertilizer plant process waters are high concentrate and especially nitrogen concentrations are high, which bring challenge to the treatment. At the theoretical part was investigated conventional and as well advanced wastewater treatment methods like reverse osmosis, adsorption and ion exchange. Beside different treatment methods corporate environmental requirements, responsibility and strategies were researched. At the empirical part of the thesis the goal was to find out possibil-ities to intensify the efficiency of purification at lamella clarifier with chemical precipitation. In addition possibility to use already existing chemical purifying plant for process waters was estimated. As a result of the research Yara has a possibility to intensify lamella clarifier’s action by addi-tion of calcium hydroxide and thus to obtain the phosphorus and fluorine to precipitate out of the water. But in practice this would be too expensive. It is possible to eliminate nitrogen compounds by adsorption or ammonia stripping, both methods requires additional testing. It is possible to process waters in chemical purifying plant, if ammonium nitrogen has been reduced before. Reverse osmosis is possible to exploit for the phosphoric acid plant’s waters.

Survey of transportation of liquid bulk chemicals in the Baltic Sea

This study is made as a part of the Chembaltic (Risks of Maritime Transportation of Chemicals in Baltic Sea) project which gathers information on the chemicals transported in the Baltic Sea. The purpose of this study is to provide an overview of handling volumes of liquid bulk chemicals (including liquefied gases) in the Baltic Sea ports and to find out what the most transported liquid bulk chemicals in the Baltic Sea are. Oil and oil products are also viewed in this study but only in a general level. Oils and oil products may also include chemical-related substances (e.g. certain bio-fuels which belong to MARPOL annex II category) in some cargo statistics. Chemicals in packaged form are excluded from the study. Most of the facts about the transport volumes of chemicals presented in this study are based on secondary written sources of Scandinavian, Russian, Baltic and international origin. Furthermore, statistical sources, academic journals, periodicals, newspapers and in later years also different homepages on the Internet have been used as sources of information. Chemical handling volumes in Finnish ports were examined in more detail by using a nationwide vessel traffic system called PortNet. Many previous studies have shown that the Baltic Sea ports are annually handling more than 11 million tonnes of liquid chemicals transported in bulk. Based on this study, it appears that the number may be even higher. The liquid bulk chemicals account for approximately 4 % of the total amount of liquid bulk cargoes handled in the Baltic Sea ports. Most of the liquid bulk chemicals are handled in Finnish and Swedish ports and their proportion of all liquid chemicals handled in the Baltic Sea is altogether over 50 %. The most handled chemicals in the Baltic Sea ports are methanol, sodium hydroxide solution, ammonia, sulphuric and phosphoric acid, pentanes, aromatic free solvents, xylenes, methyl tert-butyl ether (MTBE) and ethanol and ethanol solutions. All of these chemicals are handled at least hundred thousand tonnes or some of them even over 1 million tonnes per year, but since chemical-specific data from all the Baltic Sea countries is not available, the exact tonnages could not be calculated in this study. In addition to these above-mentioned chemicals, there are also other high volume chemicals handled in the Baltic Sea ports (e.g. ethylene, propane and butane) but exact tonnes are missing. Furthermore, high amounts of liquid fertilisers, such as solution of urea and ammonium nitrate in water, are transported in the Baltic Sea. The results of the study can be considered indicative. Updated information about transported chemicals in the Baltic Sea is the first step in the risk assessment of the chemicals. The chemical-specific transportation data help to target hazard or e.g. grounding/collision risk evaluations to chemicals that are handled most or have significant environmental hazard potential. Data gathered in this study will be used as background information in later stages of the Chembaltic project when the risks of the chemicals transported in the Baltic Sea are assessed to highlight the chemicals that require special attention from an environmental point of view in potential marine accident situations in the Baltic Sea area.

Talviaikainen happitilanne eräissä Pohjois-Savon järvissä vuosina 1997-2008

Pohjois-Savossa seurattiin talviaikaista happitilannetta vuosina 1997-2008. Seurannan kohteena oli neljä pienehköä järveä (Iso-Valkeinen, Kevätön, Kolmisoppi ja Vehmasjärvi), jotka ovat erityyppisiä syvyydeltään, rehevyystasoltaan ja humuspitoisuudeltaan. Näiden esimerkkijärvien oli tarkoitus antaa yleisemminkin viitteitä happitilanteen kehityksestä talven aikana. Alkutalven tulosten perusteella annettiin vuosittain tiedote, jossa arvioitiin happikatojen mahdollisuutta kevättalven kuluessa. Yleisöllä oli myös mahdollisuus seurata happi- ja lämpötilatuloksia Pohjois-Savon ympäristökeskuksen verkkopalvelun kautta. Hapenkulutusnopeus oli rehevimmässä seurantajärvessä kaksinkertainen verrattuna karumpiin ja syvyyden myötä ero vain korostui. Pohjanläheisessä vesikerroksessa 1 mg/l:n happipitoisuus kului karuissa järvissä noin kahdessa viikossa ja rehevässä noin kolmessa päivässä. Vuosien välinen vaihtelu oli kuitenkin hyvin suurta. Vaihtelu oli suurta myös karuissa järvissä. Veden jäätymisajankohdalla ja veden lämpötilalla on merkittävä vaikutus siihen, millainen kevättalven happitilanteesta muodostui. Seurantajärvien aineiston perusteella voidaan karkeasti arvioida, että kuukauden viivästyminen jäätymisessä tai vesipatsaan viilentyminen ennen jäätymistä asteen verran kylmemmäksi merkitsevät noin kolmanneksen korkeampaa happipitoisuutta kevättalvella. Vesipatsaan happitilanteen heikentymisen sekä ravinne- ja rautapitoisuuksien välillä todettiin vahvat yhteydet. Kaikkien järvien aineistossa happitilanteen heikkeneminen johti voimakkaimmin alusveden ammoniumtyppi-, kokonaisfosfori- ja rautapitoisuuksien kasvuun. Pitoisuusmuutokset olivat talven aikana suurimmat rehevimmässä kohdejärvessä, Kevättömässä, jossa kokonaisfosforipitoisuudet keskimäärin kymmenkertaistuivat, fosfaattifosforipitoisuudet kasvoivat keskimäärin 20-kertaisiksi ja rautapitoisuudet yli seitsenkertaisiksi.

Production of Mg(OH)2 from Mg-silicate rock for CO2 mineral sequestration

Sequestration of carbon dioxide in mineral rocks, also known as CO2 Capture and Mineralization (CCM), is considered to have a huge potential in stabilizing anthropogenic CO2 emissions. One of the CCM routes is the ex situ indirect gas/sold carbonation of reactive materials, such as Mg(OH)2, produced from abundantly available Mg-silicate rocks. The gas/solid carbonation method is intensively researched at Åbo Akademi University (ÅAU ), Finland because it is energetically attractive and utilizes the exothermic chemistry of Mg(OH)2 carbonation. In this thesis, a method for producing Mg(OH)2 from Mg-silicate rocks for CCM was investigated, and the process efficiency, energy and environmental impact assessed. The Mg(OH)2 process studied here was first proposed in 2008 in a Master’s Thesis by the author. At that time the process was applied to only one Mg-silicate rock (Finnish serpentinite from the Hitura nickel mine site of Finn Nickel) and the optimum process conversions, energy and environmental performance were not known. Producing Mg(OH)2 from Mg-silicate rocks involves a two-staged process of Mg extraction and Mg(OH)2 precipitation. The first stage extracts Mg and other cations by reacting pulverized serpentinite or olivine rocks with ammonium sulfate (AS) salt at 400 - 550 oC (preferably < 450 oC). In the second stage, ammonia solution reacts with the cations (extracted from the first stage after they are leached in water) to form mainly FeOOH, high purity Mg(OH)2 and aqueous (dissolved) AS. The Mg(OH)2 process described here is closed loop in nature; gaseous ammonia and water vapour are produced from the extraction stage, recovered and used as reagent for the precipitation stage. The AS reagent is thereafter recovered after the precipitation stage. The Mg extraction stage, being the conversion-determining and the most energy-intensive step of the entire CCM process chain, received a prominent attention in this study. The extraction behavior and reactivity of different rocks types (serpentinite and olivine rocks) from different locations worldwide (Australia, Finland, Lithuania, Norway and Portugal) was tested. Also, parametric evaluation was carried out to determine the optimal reaction temperature, time and chemical reagent (AS). Effects of reactor types and configuration, mixing and scale-up possibilities were also studied. The Mg(OH)2 produced can be used to convert CO2 to thermodynamically stable and environmentally benign magnesium carbonate. Therefore, the process energy and life cycle environmental performance of the ÅAU CCM technique that first produces Mg(OH)2 and the carbonates in a pressurized fluidized bed (FB) were assessed. The life cycle energy and environmental assessment approach applied in this thesis is motivated by the fact that the CCM technology should in itself offer a solution to what is both an energy and environmental problem. Results obtained in this study show that different Mg-silicate rocks react differently; olivine rocks being far less reactive than serpentinite rocks. In summary, the reactivity of Mg-silicate rocks is a function of both the chemical and physical properties of rocks. Reaction temperature and time remain important parameters to consider in process design and operation. Heat transfer properties of the reactor determine the temperature at which maximum Mg extraction is obtained. Also, an increase in reaction temperature leads to an increase in the extent of extraction, reaching a maximum yield at different temperatures depending on the reaction time. Process energy requirement for producing Mg(OH)2 from a hypothetical case of an iron-free serpentine rock is 3.62 GJ/t-CO2. This value can increase by 16 - 68% depending on the type of iron compound (FeO, Fe2O3 or Fe3O4) in the mineral. This suggests that the benefit from the potential use of FeOOH as an iron ore feedstock in iron and steelmaking should be determined by considering the energy, cost and emissions associated with the FeOOH by-product. AS recovery through crystallization is the second most energy intensive unit operation after the extraction reaction. However, the choice of mechanical vapor recompression (MVR) over the “simple evaporation” crystallization method has a potential energy savings of 15.2 GJ/t-CO2 (84 % savings). Integrating the Mg(OH)2 production method and the gas/solid carbonation process could provide up to an 25% energy offset to the CCM process energy requirements. Life cycle inventory assessment (LCIA) results show that for every ton of CO2 mineralized, the ÅAU CCM process avoids 430 - 480 kg CO2. The Mg(OH)2 process studied in this thesis has many promising features. Even at the current high energy and environmental burden, producing Mg(OH)2 from Mg-silicates can play a significant role in advancing CCM processes. However, dedicated future research and development (R&D) have potential to significantly improve the Mg(OH)2 process performance.

Potential utilization ways of recovered chemical products from digestate

The study evaluates the potential application of chemical substances, obtained from biogas plants` by-products. Through the anaerobic digestion process with biogas the large amount of digestate is produced. This digestate mainly consists on the organic matter with the high concentration of nutrients such as nitrogen and phosphorus. During ammonia stripping and phosphorus precipitation the products- ammonia water, ammonium sulfate, ammonium nitrate, ferrous phosphate, aluminum phosphate, calcium phosphate and struvite can be recovered. These chemicals have potential application in different industrial sectors. According to Finnish market and chemicals properties, the most perspective industrial applications were determined. Based on the data, obtained through the literature review and market study, the ammonia water was recognized as a most perspective recovered substances. According to interview provided among Finnish companies, ammonia water is used for flue gas treatment in SNCR technology. This application has a large scale in the framework of Finnish industrial sectors. As well nitrogen with phosphorous can be used as a source of nutrients in the biological wastewater treatment plants of paper mills.

Utilization of steelmaking waste materials for production of calcium carbonate (CaCO3)

The steel industry produces, besides steel, also solid mineral by-products or slags, while it emits large quantities of carbon dioxide (CO2). Slags consist of various silicates and oxides which are formed in chemical reactions between the iron ore and the fluxing agents during the high temperature processing at the steel plant. Currently, these materials are recycled in the ironmaking processes, used as aggregates in construction, or landfilled as waste. The utilization rate of the steel slags can be increased by selectively extracting components from the mineral matrix. As an example, aqueous solutions of ammonium salts such as ammonium acetate, chloride and nitrate extract calcium quite selectively already at ambient temperature and pressure conditions. After the residual solids have been separated from the solution, calcium carbonate can be precipitated by feeding a CO2 flow through the solution. Precipitated calcium carbonate (PCC) is used in different applications as a filler material. Its largest consumer is the papermaking industry, which utilizes PCC because it enhances the optical properties of paper at a relatively low cost. Traditionally, PCC is manufactured from limestone, which is first calcined to calcium oxide, then slaked with water to calcium hydroxide and finally carbonated to PCC. This process emits large amounts of CO2, mainly because of the energy-intensive calcination step. This thesis presents research work on the scale-up of the above-mentioned ammonium salt based calcium extraction and carbonation method, named Slag2PCC. Extending the scope of the earlier studies, it is now shown that the parameters which mainly affect the calcium utilization efficiency are the solid-to-liquid ratio of steel slag and the ammonium salt solvent solution during extraction, the mean diameter of the slag particles, and the slag composition, especially the fractions of total calcium, silicon, vanadium and iron as well as the fraction of free calcium oxide. Regarding extraction kinetics, slag particle size, solid-to-liquid ratio and molar concentration of the solvent solution have the largest effect on the reaction rate. Solvent solution concentrations above 1 mol/L NH4Cl cause leaching of other elements besides calcium. Some of these such as iron and manganese result in solution coloring, which can be disadvantageous for the quality of the PCC product. Based on chemical composition analysis of the produced PCC samples, however, the product quality is mainly similar as in commercial products. Increasing the novelty of the work, other important parameters related to assessment of the PCC quality, such as particle size distribution and crystal morphology are studied as well. As in traditional PCC precipitation process, the ratio of calcium and carbonate ions controls the particle shape; a higher value for [Ca2+]/[CO32-] prefers precipitation of calcite polymorph, while vaterite forms when carbon species are present in excess. The third main polymorph, aragonite, is only formed at elevated temperatures, above 40-50 °C. In general, longer precipitation times cause transformation of vaterite to calcite or aragonite, but also result in particle agglomeration. The chemical equilibrium of ammonium and calcium ions and dissolved ammonia controlling the solution pH affects the particle sizes, too. Initial pH of 12-13 during the carbonation favors nonagglomerated particles with a diameter of 1 μm and smaller, while pH values of 9-10 generate more agglomerates of 10-20 μm. As a part of the research work, these findings are implemented in demonstrationscale experimental process setups. For the first time, the Slag2PCC technology is tested in scale of ~70 liters instead of laboratory scale only. Additionally, design of a setup of several hundreds of liters is discussed. For these purposes various process units such as inclined settlers and filters for solids separation, pumps and stirrers for material transfer and mixing as well as gas feeding equipment are dimensioned and developed. Overall emissions reduction of the current industrial processes and good product quality as the main targets, based on the performed partial life cycle assessment (LCA), it is most beneficial to utilize low concentration ammonium salt solutions for the Slag2PCC process. In this manner the post-treatment of the products does not require extensive use of washing and drying equipment, otherwise increasing the CO2 emissions of the process. The low solvent concentration Slag2PCC process causes negative CO2 emissions; thus, it can be seen as a carbon capture and utilization (CCU) method, which actually reduces the anthropogenic CO2 emissions compared to the alternative of not using the technology. Even if the amount of steel slag is too small for any substantial mitigation of global warming, the process can have both financial and environmental significance for individual steel manufacturers as a means to reduce the amounts of emitted CO2 and landfilled steel slag. Alternatively, it is possible to introduce the carbon dioxide directly into the mixture of steel slag and ammonium salt solution. The process would generate a 60-75% pure calcium carbonate mixture, the remaining 25-40% consisting of the residual steel slag. This calcium-rich material could be re-used in ironmaking as a fluxing agent instead of natural limestone. Even though this process option would require less process equipment compared to the Slag2PCC process, it still needs further studies regarding the practical usefulness of the products. Nevertheless, compared to several other CO2 emission reduction methods studied around the world, the within this thesis developed and studied processes have the advantage of existing markets for the produced materials, thus giving also a financial incentive for applying the technology in practice.

Sustainable Gold Mining- Life Cycle Assessment of Cyanidation and Thiosulphate Leaching

With the increasing concern of the sustainable approach of gold mining, thiosulphate has been researched as an alternative lixiviant to cyanide since cyanide is toxic to the environment. In order to investigate the possibility of thiosulphate leaching application in the coming future, life cycle assessment, is conducted to compare the environmental footprint of cyanidation and thiosulphate leaching. The result showed the most significant environmental impact of cyanidation is toxicity to human, while the ammonia of thiosulphate leaching is also a major concern of acidification. In addition, an ecosystem evaluation is also performed to indicate the potential damages caused by an example of cyanide spill at Kittilä mine, resulting in significant environmental risk cost that has to be taken into account for decision making. From the opinion collected from an online LinkedIn discussion forum, the anxiety of sustainability alone would not be enough to contribute a significant change of conventional cyanidation, until the tighten policy of cyanide use. International Cyanide Code, therefore, is crucial for safe gold production. Nevertheless, it is still thoughtful to consider the values of healthy ecosystem and the gold for long-term benefit.