Intensification of hemicellulose hot-water extraction from spruce wood by parameter tuning

The growing population on earth along with diminishing fossil deposits and the climate change debate calls out for a better utilization of renewable, bio-based materials. In a biorefinery perspective, the renewable biomass is converted into many different products such as fuels, chemicals, and materials, quite similar to the petroleum refinery industry. Since forests cover about one third of the land surface on earth, ligno-cellulosic biomass is the most abundant renewable resource available. The natural first step in a biorefinery is separation and isolation of the different compounds the biomass is comprised of. The major components in wood are cellulose, hemicellulose, and lignin, all of which can be made into various end-products. Today, focus normally lies on utilizing only one component, e.g., the cellulose in the Kraft pulping process. It would be highly desirable to utilize all the different compounds, both from an economical and environmental point of view. The separation process should therefore be optimized. Hemicelluloses can partly be extracted with hot-water prior to pulping. Depending in the severity of the extraction, the hemicelluloses are degraded to various degrees. In order to be able to choose from a variety of different end-products, the hemicelluloses should be as intact as possible after the extraction. The main focus of this work has been on preserving the hemicellulose molar mass throughout the extraction at a high yield by actively controlling the extraction pH at the high temperatures used. Since it has not been possible to measure pH during an extraction due to the high temperatures, the extraction pH has remained a “black box”. Therefore, a high-temperature in-line pH measuring system was developed, validated, and tested for hot-water wood extractions. One crucial step in the measurements is calibration, therefore extensive efforts was put on developing a reliable calibration procedure. Initial extractions with wood showed that the actual extraction pH was ~0.35 pH units higher than previously believed. The measuring system was also equipped with a controller connected to a pump. With this addition it was possible to control the extraction to any desired pH set point. When the pH dropped below the set point, the controller started pumping in alkali and by that the desired set point was maintained very accurately. Analyses of the extracted hemicelluloses showed that less hemicelluloses were extracted at higher pH but with a higher molar-mass. Monomer formation could, at a certain pH level, be completely inhibited. Increasing the temperature, but maintaining a specific pH set point, would speed up the extraction without degrading the molar-mass of the hemicelluloses and thereby intensifying the extraction. The diffusion of the dissolved hemicelluloses from the wood particle is a major part of the extraction process. Therefore, a particle size study ranging from 0.5 mm wood particles to industrial size wood chips was conducted to investigate the internal mass transfer of the hemicelluloses. Unsurprisingly, it showed that hemicelluloses were extracted faster from smaller wood particles than larger although it did not seem to have a substantial effect on the average molar mass of the extracted hemicelluloses. However, smaller particle sizes require more energy to manufacture and thus increases the economic cost. Since bark comprises 10 – 15 % of a tree, it is important to also consider it in a biorefinery concept. Spruce inner and outer bark was hot-water extracted separately to investigate the possibility to isolate the bark hemicelluloses. It was showed that the bark hemicelluloses comprised mostly of pectic material and differed considerably from the wood hemicelluloses. The bark hemicelluloses, or pectins, could be extracted at lower temperatures than the wood hemicelluloses. A chemical characterization, done separately on inner and outer bark, showed that inner bark contained over 10 % stilbene glucosides that could be extracted already at 100 °C with aqueous acetone.

Wood biochemicals for the protection of health. Focus on hemicellulose, stilbenoids and lignans

Trees produce an enormous amount of compounds that are still scantly utilized.However, the results obtained from structurally similar biochemicals suggest that wood-derived compounds could be used for the protection of health in various applications. Polyphenols, for instance, could be extracted from wood in high quantities. Similar polyphenols to those in wood include resveratrol, found in grapes, and secoisolariciresinol, present in flaxseeds. Their consumption has been inversely associated with the incidence of various diseases, especially certain cancers and obesity-related disorders. The aim of this study was to determine the health-promoting effects of woodderived biochemicals. The effect of spruce hemicellulose on the growth of probiotic intestinal bacteria was studied. The results suggest that the bifidobacteria and lactobacilli can utilize hemicellulose and thus it has potential as a prebiotic compound. In particular, the efficacy of pine polyphenols to inhibit the growth of prostate cancer was our main interest. It was found that stilbenoids and lignans inhibited the proliferation of various cancer cells, and reduced the growth of prostate cancer xenografts in mice. The polyphenol rich pine knot extract was well tolerated in diet and extract-derived polyphenols were rapidly absorbed after intake. Furthermore, we determined the effect of the dietary pine knot extract on the weight gain and the expression of aromatase gene in reporter mouse expressing the promoter region of a human aromatase gene. It was found that dietary pine knot extract alleviated the obesity-induced inflammation in adipose tissue and downregulated the expression of a human aromatase gene. Taken together, several components of spruce and pine may have a future role as health-promoting compounds.

Feasibility of the use of recycled nutrients in fast growing pulpwood production

The application of pulp and paper mill (PPM) sludge in agriculture and forestry has been acknowledged as soil amendments and a plant nutrient source. The main objectives of this study were to evaluate the total cost of the use of recycled nutrients from PPM sludge in fast growing pulpwood production, and the financial profitability of fast growing pulpwood production with the use of these recycled nutrients. The investment and production costs of fast growing pulpwood plantation were directly acquired from a previous research, while the other data was compiled through different studies. The total cost of the use of PPM sludge was evaluated based on assumed factors. Discounted cash flow method was used to evaluate the financial profitability, using NPV and IRR as indicators. The results of estimated sludge nutrient contents were 16.2 g N, 2.9 g P, and 2.4 g K kg-1 of dry sludge. The sludge application rate was estimated at 1.36 Mg/ha in the first year. The total cost of the use of PPM sludge involved transport and spreading cost of US$49.15/dry ton. The fertilization cost applied in the financial model was designed in 3 different options and their results were as follows: option (1) was taken directly from the reference research (US$97/ha); option (2) was the use of sludge alone (US$66.75/ha); and option (3) was the use of sludge and TSP fertilizer (US$83.80/ha). The average NPV without discounting was US$248,180 while the IRRs ranged between approximately 3-4% with an average of 3.63%. Although option (2) and (3) contributed to higher IRRs compared to option (1), this increase was still not significant as the IRR was not sensitive to the total fertilization cost. The advantages are that this practice can be performed at a lower cost and the application rate can be still increased if necessary. It is better for forest plantations compared to agriculture and consequently supports reforestation program. In addition, it can be similarly applied in wood biomass production. A disadvantage is that the IRRs were not very favorable compared to the criterion of 11%. The sludge high in C:N ratio can cause nitrogen immobilization, and regulatory concerns may restrict and complicate the use of sludge landspreading and contribute to additional costs and processes.

Rankapuun ja -hakkeen laadun vaihtelu terminaalivarastoinnissa

Työssä tutkittiin polttoaineterminaalissa varastoitavan puupolttoaineen laadunmuutoksia. Tutkimuksessa tarkasteltiin hakettamattomien rankapuiden ja rankapuuhakkeen kosteuden ja lämpöarvon muutosta. Myös kuiva-ainetappiota tutkittiin aikaisempien tutkimusten perusteella. Tutkimusaineisto kerättiin Etelä-Savon Energian polttoaineterminaaleista. Kosteus-pitoisuuksia mitattiin Hydromette M2050 -pikakosteusmittarilla ja uunikuivaus-menetelmällä standardin SFS-EN 14774 mukaisesti. Tutkimuksessa huomattiin pikakosteusmittarin toimivan riittävän luotettavalla tasolla rankapuiden mittauksissa, mutta hakkeen mittauksissa mittari osoittautui toimimattomaksi. Varastointiaika ei vaikuttanut polttoaineiden lämpöarvoihin, mutta kosteuspitoisuus vaihteli suuresti. Tutkimustuloksista pääteltiin rangan kuivuvan terminaalivarastossa ja hakkeen kosteuden pysyvän vakiona. Energiasisällön puolesta rankapuuta voidaan varastoida yli 2 vuotta, mutta hakkeen varastointiaika tulisi pitää mahdollisimman lyhyenä.

Uniformity of dry bacteriorhodopsin films

Bacteriorhodopsin (BR) is a light-sensitive protein, which is a promising material for various technical applications, such as photosensors. The quality of dry thick BR photosensors depends on few performance characteristics. Uniformity of parameters, which have the impact on such characteristics, should be maintained during the preparation or otherwise compensated afterwards. In this thesis, uniformity examination techniques were studied. Experimental setups, which operate, based on studied techniques, were designed. Experiments, which were conducted on constructed setups, revealed a list of dependencies between BR properties and allowed to evaluate properties of sensors.

Improving the fire retardancy of extruded/coextruded wood-plastic composites

The main objective of this thesis is to study the impact of different mineral fillers and fire retardants on the reaction-to-fire properties of extruded/coextruded wood-plastic composites (WPCs). The impact of additives on the flammability properties of WPCs is studied by cone calorimetry. The studied properties are ignition time, peak heat release rate, total heat release, total smoke production, and mass loss rate. The effects of mineral fillers and fire retardants were found to vary with the type of additive, the type of additive combinations, the amount of additives, as well as the production method of the WPCs. The study shows that talc can be used to improve the properties of extruded WPCs. Especially ignition time, peak heat release rate and mass loss rate were found to be improved significantly by talc. The most significant improvement in the fire retardancy of coextruded WPCs was achieved in combinations of natural graphite and melamine. Ignition time, peak heat release rate and total smoke production were improved essentially. High increase in smoke production was found in samples where the amount of ammonium polyphosphate was 10% or higher. Coextrusion as a structural modification was found as a promising way to improve the flammability properties of composite materials in a cost-effective way.

Improving Cost-Efficiency and Reducing Environmental Impacts of Intermodal Transportation with Dry Port Concept – Major Rail Transport Corridor in Baltic Sea Region

Transportation plays a major role in the gross domestic product of various nations. There are, however, many obstacles hindering the transportation sector. Cost-efficiency along with proper delivery times, high frequency and reliability are not a straightforward task. Furthermore, environmental friendliness has increased the importance of the whole transportation sector. This development will change roles inside the transportation sector. Even now, but especially in the future, decisions regarding the transportation sector will be partly based on emission levels and other externalities originating from transportation in addition to pure transportation costs. There are different factors, which could have an impact on the transportation sector. IMO’s sulphur regulation is estimated to increase the costs of short sea shipping in the Baltic Sea. Price development of energy could change the roles of different transport modes. Higher awareness of the environmental impacts originating from transportation could also have an impact on the price level of more polluting transport modes. According to earlier research, increased inland transportation, modal shift and slowsteaming can be possible results of these changes in the transportation sector. Possible changes in the transportation sector and ways to settle potential obstacles are studied in this dissertation. Furthermore, means to improve cost-efficiency and to decrease environmental impacts originating from transportation are researched. Hypothetical Finnish dry port network and Rail Baltica transport corridor are studied in this dissertation. Benefits and disadvantages are studied with different methodologies. These include gravitational models, which were optimized with linear integer programming, discrete-event and system dynamics simulation, an interview study and a case study. Geographical focus is on the Baltic Sea Region, but the results can be adapted to other geographical locations with discretion. Results indicate that the dry port concept has benefits, but optimization regarding the location and the amount of dry ports plays an important role. In addition, the utilization of dry ports for freight transportation should be carefully operated, since only a certain amount of total freight volume can be cost-efficiently transported through dry ports. If dry ports are created and located without proper planning, they could actually increase transportation costs and delivery times of the whole transportation system. With an optimized dry port network, transportation costs can be lowered in Finland with three to five dry ports. Environmental impacts can be lowered with up to nine dry ports. If more dry ports are added to the system, the benefits become very minor, i.e. payback time of investments becomes extremely long. Furthermore, dry port network could support major transport corridors such as Rail Baltica. Based on an analysis of statistics and interview study, there could be enough freight volume available for Rail Baltica, especially, if North-West Russia is part of the Northern end of the corridor. Transit traffic to and from Russia (especially through the Baltic States) plays a large role. It could be possible to increase transit traffic through Finland by connecting the potential Finnish dry port network and the studied transport corridor. Additionally, sulphur emission regulation is assumed to increase the attractiveness of Rail Baltica in the year 2015. Part of the transit traffic could be rerouted along Rail Baltica instead of the Baltic Sea, since the price level of sea transport could increase due to the sulphur regulation. Both, the hypothetical Finnish dry port network and Rail Baltica transport corridor could benefit each other. The dry port network could gain more market share from Russia, but also from Central Europe, which is the other end of Rail Baltica. In addition, further Eastern countries could also be connected to achieve higher potential freight volume by rail.

Utilization of recycled mineral wool as filler in wood plastic composites

The impact of a recycled mineral wool filler on the various properties of wood plastic composites was studied and the critical factors affecting the formation of the properties were determined. An estimation of the volume of mineral wool fiber waste generated in the European Union between the years 2010-2020 was presented. Furthermore, the effect of fiber pre-treatment on the properties of the wood plastic composites were studied, and the environmental performance of a wood plastic composite containing recycled mineral fibers was assessed. The results showed that the volumes of construction and demolition waste and new mineral wool produced in the European Union are growing annually, and therefore also the volumes of recycled mineral wool waste generated are increasing. The study showed that the addition of recycled mineral wool into composites can enhance some of the mechanical properties and increase the moisture resistance properties of the composites notably. Recycled mineral wool as a filler in wood plastic composites can also improve the fire resistance properties of composites, but it does not protect the polymer matrix from pyrolysis. Fiber pre-treatment with silane solution improved some of the mechanical properties, but generally the use of maleated polypropylene as the coupling agent led to better mechanical and moisture resistance properties. The environmental performance of recycled mineral wool as the filler in wood plastic composites was superior compared to glass fibers. According to the findings, recycled mineral wool fibers can provide a technically and environmentally viable alternative to the traditional inorganic filler materials used in wood plastic composites.

Functionalisation of spruce O-acetyl-galactoglucomannans for barrier and composite applications

The increasing use of energy, food, and materials by the growing population in the world is leading to the situation where alternative solutions from renewable carbon resources are sought after. The growing use of plastics depends on the raw-oil production while oil refining are politically governed and required for the polymer manufacturing is not sustainable in terms of carbon footprint. The amount of packaging is also increasing. Packaging is not only utilising cardboard and paper, but also plastics. The synthetic petroleum-derived plastics and inner-coatings in food packaging can be substituted with polymeric material from the renewable resources. The trees in Finnish forests constitute a huge resource, which ought to be utilised more effectively than it is today. One underutilised component of the forests is the wood-derived hemicelluloses, although Spruce Oacetyl-galactoglucomannans (GGMs) have previously shown high potential for material applications and can be recovered in large scale. Hemicelluloses are hydrophilic in their native state, which restrains the use of them for food packaging as non-dry item. To cope with this challenge, we intended to make GGMs more hydrophobic or amphiphilic by chemical grafting and consequently with the focus of using them for barrier applications. Methods of esterification with anhydrides and cationic etherification with a trimethyl ammonium moiety were established. A method of controlled synthesis to obtain the desired properties by the means of altering temperature, reaction time, the quantity of the reagent, and even the solvent for purification of the products was developed. Numerous analytical tools, such as NMR, FTIR, SEC-MALLS/RI, MALDI-TOF-MS, RP-HPLC and polyelectrolyte titration were used to evaluate the products from different perspectives and to acquire parallel proofs of their chemical structure. Modified GGMs with different degree of substitution and the correlating level of hydrophobicity was applied as coatings on cartonboard and on nanofibrillated cellulose-GGM films to exhibit barrier functionality. The water dispersibility in processing was maintained with GGM esters with low DS. The use of chemically functionalised GGM was evaluated for the use as barriers against water, oxygen and grease for the food packaging purposes. The results show undoubtedly that GGM derivatives exhibit high potential to function as a barrier material in food packaging.

Enhancement of ultrafiltration process by pretreatment in recovery of hemicelluloses from wood extracts

Hemicelluloses are potential raw material for several items produced in future wood-based biorefineries. One possible method for recovering hemicelluloses from wood extracts is ultrafiltration (UF). However, low filtration capacities and severe fouling restrict the use of tight UF membranes in the treatment of wood extracts. The lack of suitable commercial membranes creates a need for pretreatment which would decrease fouling and increase the filtration capacity. This thesis focuses on the evaluation of the possibility to improve the filtration capacity and decrease fouling with the pretreatment of wood extracts. Methods which remove harmful compounds and methods which degrade them are studied, as well as combinations of the methods. The tested pretreatments have an influence on both the concentration of different compounds and the molecular mass distribution of the compounds in the extract. This study revealed that in addition to which kind of compounds were removed, also the change in molecular size distribution affected the filtration capacity significantly. It was shown that the most harmful compounds for the filtration capacity of the hydrophobic 5 kDa membrane were the ones capable of permeating the membrane and fouling also the inner membrane structure. Naturally, the size of the most harmful compounds depends on the used UF membrane and is thus case-specific. However, in the choice of the pretreatment method, the focus should be on the removal of harmful compound sizes rather than merely on the total amount of removed foulants. The results proved that filtration capacity can be increased with both adsorptive and oxidative pretreatments even by hundreds of per cents. For instance, the use of XAD7 and XAD16 adsorbents increased the average flux in the UF of a birch extract from nearly zero to 107 kg/(m2h) and 175 kg/(m2h), respectively. In the treatment of a spruce extract, oxidation by pulsed corona discharge (PCD) increased the flux in UF from 46 kg/(m2h) to 158 kg/(m2h). Moreover, when a birch extract batch was treated with laccase enzyme, the flux in UF increased from 15 kg/(m2h) to 36 kg/(m2h). However, fouling was decreased only by adsorptive pretreatment while oxidative methods had a negligible or even negative impact on it. This demonstrates that filtration capacity and fouling are affected by different compounds and mechanisms. The results of this thesis show that filtration capacity can be improved and fouling decreased through appropriate pretreatment. However, the choice of the best possible pretreatment is case-specific and depends on the wood extract and the membrane used. Finding the best option requires information on the extract content and membrane characteristics as well as on the filtration performance of the membrane in the prevailing conditions and a multivariate approach. On the basis of this study, it can be roughly concluded that adsorptive pretreatment improves the filtration capacity and decreases fouling rather reliably, but it may lead to significant hemicellulose losses. Oxidation reduces the loss of valuable hemicelluloses and could improve the filtration capacity, but fouling challenges may remain. Combining oxidation with adsorptive pretreatment was not a solution for avoiding hemicellulose losses in the tested cases.

Optical and photoelectric properties of dry bacteriorhodopsin sensors

In this thesis, bacteriorhodopsin (BR) photosensor’s optical and electrical properties were studied. The BR sensor consisted of a dry film with BR in polyvinyl alcohol and covered with transparent conductors. In the experiments the BR photocycle was started with two lasers. The characteristics of the BR sensor were measured in two ways. The first approach was theoretical and it required knowing the laser parameters. The second way required assembling a measurement setup for the optical response measurements. However, no measurable results were obtained due to low laser power. The photoelectric response was measured in the experiments with two laser systems and the amplifier was tested. In the experiment with a Cavitar laser, the photoelectric response was obtained. In the experiment with FemtoFiber Pro laser, the photoelectric response was not measured. The expected amplitude of the response was obtained. The experimental data was analyzed and possible solutions for reducing the interference were given.

Tuotannon- ja materiaalinsuunnittelu ja sen ennustaminen Metsä Wood:n Suolahden koivuvaneritehtaalla

Tässä diplomityössä tutkitaan Metsä Woodin Suolahden koivuvaneritehtaan toimitustarkkuuteen negatiivisesti vaikuttavia tekijöitä. Tarkoituksena on löytää ne ongelmakohdat, mitkä heijastuvat toimitusten myöhästymisenä sekä muutostekijät, mitkä vaikuttavat toimitusviikon myöntämiseen. Lisäksi työssä kartoitetaan kuinka hyvin tietoa ja informaatiota on tarjolla sitä tarvitseville henkilöstötahoille. Teoriaosuudessa tarkastellaan tuotannonsuunnitteluun liittyviä teorioita sekä tiedon liikkumista organisaation sisällä. Työssä kuvataan Suolahden koivuvaneritehtaan nykyinen vanerin valmistusprosessi ja tuotannonsuunnittelu. Varsinainen tutkimustyö suoritetaan laadullisia tutkimusmenetelmiä hyväksikäyttäen. Tulosten tarkastelussa käsitellään työn aikana tapahtuneita muutoksia ja ongelmakohtia sekä analysoidaan kyselytutkimuksen tuloksia ja tulosten luotettavuutta. Yhteenvedossa esitetään pääongelmakohdat ja niiden ratkaisut ja esitetään uusia mielenkiintoisia jatkotutkimusaiheita.

Wood species identification by visual characterization of fibers

Kandidaatintyö tehtiin osana PulpVision-tutkimusprojektia, jonka tarkoituksena on kehittää kuvapohjaisia laskenta- ja luokittelumetodeja sellun laaduntarkkailuun paperin valmistuksessa. Tämän tutkimusprojektin osana on aiemmin kehitetty metodi, jolla etsittiin kaarevia rakenteita kuvista, ja tätä metodia hyödynnettiin kuitujen etsintään kuvista. Tätä metodia käytettiin lähtökohtana kandidaatintyölle. Työn tarkoituksena oli tutkia, voidaanko erilaisista kuitukuvista laskettujen piirteiden avulla tunnistaa kuvassa olevien kuitujen laji. Näissä kuitukuvissa oli kuituja neljästä eri puulajista ja yhdestä kasvista. Nämä lajit olivat akasia, koivu, mänty, eukalyptus ja vehnä. Jokaisesta lajista valittiin 100 kuitukuvaa ja nämä kuvat jaettiin kahteen ryhmään, joista ensimmäistä käytettiin opetusryhmänä ja toista testausryhmänä. Opetusryhmän avulla jokaiselle kuitulajille laskettiin näitä kuvaavia piirteitä, joiden avulla pyrittiin tunnistamaan testausryhmän kuvissa olevat kuitulajit. Nämä kuvat oli tuottanut CEMIS-Oulu (Center for Measurement and Information Systems), joka on mittaustekniikkaan keskittynyt yksikkö Oulun yliopistossa. Yksittäiselle opetusryhmän kuitukuvalle laskettiin keskiarvot ja keskihajonnat kolmesta eri piirteestä, jotka olivat pituus, leveys ja kaarevuus. Lisäksi laskettiin, kuinka monta kuitua kuvasta löydettiin. Näiden piirteiden eri yhdistelmien avulla testattiin tunnistamisen tarkkuutta käyttämällä k:n lähimmän naapurin menetelmää ja Naiivi Bayes -luokitinta testausryhmän kuville. Testeistä saatiin lupaavia tuloksia muun muassa pituuden ja leveyden keskiarvoja käytettäessä saavutettiin jopa noin 98 %:n tarkkuus molemmilla algoritmeilla. Tunnistuksessa kuitujen keskimäärinen pituus vaikutti olevan kuitukuvia parhaiten kuvaava piirre. Käytettyjen algoritmien välillä ei ollut suurta vaihtelua tarkkuudessa. Testeissä saatujen tulosten perusteella voidaan todeta, että kuitukuvien tunnistaminen on mahdollista. Testien perusteella kuitukuvista tarvitsee laskea vain kaksi piirrettä, joilla kuidut voidaan tunnistaa tarkasti. Käytetyt lajittelualgoritmit olivat hyvin yksinkertaisia, mutta ne toimivat testeissä hyvin.