Tertiary treatment of pulp and paper mill effluents

Työn tavoitteena oli selvittää mitä käsittelyvaihtoehtoja on olemassa jäteveden puhdistamon tertiäärikäsittelyyn ja miten suuri tarve paperi- ja selluteollisuuden prosessivesien puhdistukseen on. Tarkoituksena oli saada käsitys koko tertiäärikäsittelystä eri näkökulmista. Lopuksi läpikäytiin tertiäärikäsittelymenetelmiä ja etsittiin mahdollisia uusia menetelmiä, joita voitaisiin käyttää jäteveden tertiääripuhdistukseen. Ensimmäisenä työssä on perehdytty jäteveden koostumukseen paperi- ja selluteollisuudessa ja puhdistukseen ilmastetulla aktiivilietemenetelmällä, jotta tertiäärikäsittely ymmärrettäisiin konseptina paremmin. Lisäksi työssä selvitettiin tertiäärikäsittelyn tarvetta ja vaihtoehtoja sen käyttämättä jättämiselle teollisuuden ja muun ympäristöä vahingoittavan toiminnan ympäristönäkökohdat huomioonottaen. Lyhyiden menetelmäesitysten jälkeen kiteytetään tertiäärikäsittelyn ympäristönäkökohdatja vaihtoehdot sen käytölle yhteenvetona, jossa otetaan huomioon myös viranomaisten, yrityksen ja BAT referenssien sisältämä tieto tertiäärikäsittelystä. Työn kokeellinen osa sisältää erään tertiäärikäsittelysovelluksenrakentamisen, koekäytön ja laboratorioanalyysien yhteenvedon. Lisäksi menetelmää verrataan kustannus-tehokkuudeltaan vastaavien menetelmien kanssa. Tarkoituksena oli löytää jäteveden tertiäärikäsittelyyn sopiva laitteisto, jonka toimintaanei sisältyisi kemikaalien annostelua ja sitä käytettäisiin lähinnä jätevedenpuhdistamon ongelmatilanteiden väliaikaiseksi ratkaisuksi. Mahdollisesti se voisi toimia myös jatkuvatoimisesti veden kirkastuksessa. Diplomityössä rakennettu laitteisto, jota käytettiin myös pilot koeajoissa, ei ollut paras mahdollinen laitteisto tertiäärikäsittelyn toteuttamiseksi paperi- ja selluteollisuudessa, mutta kilpailukykyinen muiden laitteistojen kanssa. Laitteiston toimintaperiaate on kuitenkin käyttökelpoinen tietyin varauksin ja sitä voidaan käyttää vedenpuhdistamiseen.

Regenerated cellulose ultrafiltration membranes in the treatment of pulp and paper mill process waters

Ultrafiltration (UF) is widely applied in different separation processes in the pulp and paper industry. The growing need to protect the environment, a lack of pure water and an interest in producing high-value chemicals from compounds present in process waters will probably lead to an increase in the use of UF in the pulp and paper industry. The efficiency and cost-effectiveness of a UF process depends on the applied membrane. The membrane should have a high and stable filtration capacity, a particular selectivity and a long operational lifetime. To meet these requirements a membrane should have a low fouling tendency. In addition, it should withstand the prevailing operational and chemical conditions. This thesis evaluates the performance and applicability of the regenerated cellulose (RC) membranes 00030T and C2 in the treatment of pulp and paper mill process waters based on the requirements above. The results demonstrated that both the tested RC membranes fulfilled well the requirement of high filtration capacity. In addition, in the filtration of a paper mill clear filtrate (CF) the RC membranes were not as greatly affected by variations in the CF quality as a polysulphone membrane. Furthermore, due to their extreme hydrophilicity and weak charge the fouling tendency of the membranes can be expected to be low in pulp and paper mill filtration applications. It is, however, known that fouling cannot be totally avoided even when the membrane is chosen very carefully. This study indicated that carbohydrates influenced negatively on permeability and caused fouling in the filtration of groundwood mill circulation water. Thus, a pre-treatment effectively reducing the amount of carbohydrates might help to maintain a stable capacity. However, the results of the thesis also showed that the removal of some of the possible foulants might just increase the harmful effect of others. Multivariate examination was useful in the understanding of the complicated factors causing the unstable capacity. The thesis also revealed that the 00030T and C2 membranes can be used at high pressure (max. tested pressure 12 bar). The C2 membrane, having a sponge-like substructure, was more pressure resistant, and its performance was more stable at high pressure compared to the UCO30T membrane containing macrovoids in its substructure. Both tested membranes can, according to the results, also be used at temperatures as high as 70°C in acidic, neutral and alkaline conditions. However, the use at extreme conditions might cause faster ageing of the membranes compared to ageing in neutral conditions. The thesis proved that both the tested RC membranes are very suitable for pulp and paper mill applications and that the membranes can be utilised in processes operating in challenging conditions. Thus, they could be used in more demanding applications than supposed earlier.

Effects of pulp electrochemistry on PGE flotation in sulphide poor ores

This work gives a reader basic knowledge about mineralogy and mineral processing. Main focus of this work was on flotation process and pulp electrochemistry on flotation. Three different sulphide poor ores are examined on experimental part. Platinum and palladium were the noble metals, which were contained into studied ores. Electrochemistry of flotation of PGE minerals on sulphide poor ores has been examined only slightly. Bench scale flotation test was used in this study. Chalcopyrite, nickel-pentlandite, pyrite, platinum and pH electrodes were used to investigation of pulp electrochemistry during flotation tests. Effects of grinding media, carbon dioxide atmosphere in grinding and mixture of carbon dioxide and air as flotation gas to PGE flotation and electrochemistry of flotation were studied. Stainless steel grinding media created more oxidising pulp environment to flotation than mild steel grinding media. Concentrate quality improved also with stainless steel grinding media, but the recovery was remarkably poorer, than with mild steel grinding media. Carbon dioxide atmosphere in grinding created very reducing pulp environment, which caused very good concentrate quality. But the recovery was again poorer than with normal mild steel grinding media. Mixture of carbon dioxide and air as flotation gas improved PGE recovery with some ores, but not always. Effect of carbon dioxide to pulp electrochemistry was detected mainly via pH-value.

The effect of pulp washing on bleaching efficiency

The main aim of this study was to inspect the influence of the ultrafiltration implementation on the washing and on bleaching efficiency. Four cases corresponding to four washing stages were observed: two with hardwood pulp and two with softwood pulp; each case had a reference and a trial experiment. The experiments with hardwood pulp were arranged in a manner to explore predominantly the possibility of bleaching performance improvement by applying for washing instead of untreated filtrate (reference case) the same treated one (trial case). Despite that the ultrafiltration reduced the COD of the wash filtrates allowing the decreasing of COD carry-over to the bleaching stage it didn’t affect the bleaching performance. Another set was used in the experiments with softwood pulp. It implied the ultrafiltration and recirculation of the filtrate to the same washing stage with the purpose to reduce the volumes and pollution of the bleaching effluents. In one case the negative result was obtained which was expressed by worse parameters of the pulp after bleaching. Another case showed the opportunity to replace hot water with the filtrate and reduce the fresh water consumption.

Protestant Churches and the making of the Universal Declaration of Human Rights

Kirjallisuusarvostelu

The oxygenation in biological wastewater treatment of pulp and paper industry

The UPM-Kymmene Oyj Pietarsaari pulp and paper Mill biological wastewater treatment plant was built in the 1980's and the plant has been in use ever since. During the past years there have been problems with deviations. The wastewater treatment plant needs update, especially the aeration basin, where the old surface aerators cannot produce enough mixing and indroduce oxygen enough to the wastewater. In this thesis how extra aeration with oxygen affects the wastewater treatment plant effluent was studied. In the literature part the main focus is in aeration devices, which can be used in biological wastewater treatment. The target is to compare different kind of aerators, which are suitable for pulp and paper wastewater treatment. Studies show, that EDI-aerators are commonly used and also most suitable. In the experimental part, the focus is on the Pietarsaari Mills wastewater treatment plant and oxygen aeration during autumn 2008. This thesis presents the results of the trial run. Studies show, that extra oxygen devices can produce lot a of mixing and the oxygenation capacity was more than what the micro-organisms needed. The effect on sludge quality could not been seen during the trial runs.

Soldiering and the making of Finnish manhood : conscription and masculinity in interwar Finland, 1918–1939

Military conscription and peacetime military service were the subjects of heated political, social and cultural controversies during the early years of national independence in Finland. Both the critics and the supporters of the existing military system described it as strongly formative of young men’s physical and moral development into adult men and male citizens. The conflicts over conscription prompted the contemporaries to express their notions about what Finnish men were like, at their best and at their worst, and what should and could be done about it. This thesis studies military conscription as an arena for the “making of manhood” in peacetime Finnish society, 1918–1939. It examines a range of public images of conscripted soldiering, asking how soldiering was depicted and given gendered meanings in parliamentary debates, war hero myths, texts concerned with the military and civic education of conscripts, as well as in works of fiction and reminiscences about military training as a personal experience. Studying conscription with a focus on masculinity, the thesis explores the different cultural images of manliness, soldiering and male citizenship on offer in Finnish society. It investigates how political parties, officers, educators, journalists, writers and “ordinary” conscripts used and developed, embraced or rejected these notions, according to their political purposes or personal needs. The period between the two world wars can be described as a fast-forward into military modernity in Finland. In the process, European middle class gender ideologies clashed with Finnish agrarian masculinities. Nationalistic agendas for the militarisation of Finnish manhood stumbled against intense class conflicts and ideological resistance. Military propaganda used images of military heroism, civic virtue and individual success to persuade the conscripts into ways of thinking and acting that were shaped by bourgeois mentality, nationalistic ideology and religious morality. These images are further analysed as expressive of the personal experiences and emotions of their middle-aged, male authors. The efforts of these military educators were, however, actively resisted on many fronts, ranging from rural working class masculinities among the conscripted young men to ideological critiques of the standing army system in parliament. In narratives about military training, masculinity was depicted as both strengthened and contradicted by the harsh and even brutal practices of interwar Finnish military training. The study represents a combination of new military history and the historical study of men and masculinities. It approaches masculinity as a contested and highly political form of social and cultural knowledge that is actively and selectively used by historic actors. Instead of trying to identify a dominant or “hegemonic” form of masculinity within a pre-determined theoretical structure, this study examines how the meanings ascribed to manhood varied according to class, age, political ideology and social situation. The interwar period in Finland can be understood as a period of contest between different notions of militarised masculinity, yet to judge by the materials studied, there was no clear winning party in that contest. A gradual movement from an atmosphere of conflict surrounding conscription towards political and cultural compromises can be discerned, yet this convergence was incomplete and many division lines remained.

Identification of extractives and polysaccharides as foulants in membrane filtration of pulp and paper mill effluents

The search for new renewable materials has intensified in recent years. Pulp and paper mill process streams contain a number of potential compounds which could be used in biofuel production and as raw materials in the chemical, food and pharmaceutical industries. Prior to utilization, these compounds require separation from other compounds present in the process stream. One feasible separation technique is membrane filtration but to some extent, fouling still limits its implementation in pulp and paper mill applications. To mitigate fouling and its effects, foulants and their fouling mechanisms need to be well understood. This thesis evaluates fouling in filtration of pulp and paper mill process streams by means of polysaccharide model substance filtrations and by development of a procedure to analyze and identify potential foulants, i.e. wood extractives and carbohydrates, from fouled membranes. The model solution filtration results demonstrate that each polysaccharide has its own fouling mechanism, which also depends on the membrane characteristics. Polysaccharides may foul the membranes by adsorption and/or by gel/cake layer formation on the membrane surface. Moreover, the polysaccharides interact, which makes fouling evaluation of certain compound groups very challenging. Novel methods to identify wood extractive and polysaccharide foulants are developed in this thesis. The results show that it is possible to extract and identify wood extractives from membranes fouled in filtration of pulp and paper millstreams. The most effective solvent was found to be acetone:water (9:1 v/v) because it extracted both lipophilic extractives and lignans at high amounts from the fouled membranes and it was also non-destructive for the membrane materials. One hour of extraction was enough to extract wood extractives at high amounts for membrane samples with an area of 0.008 m2. If only qualitative knowledge of wood extractives is needed a simplified extraction procedure can be used. Adsorption was the main fouling mechanism in extractives-induced fouling and dissolved fatty and resin acids were mostly the reason for the fouling; colloidal fouling was negligible. Both process water and membrane characteristics affected extractives-induced fouling. In general, the more hydrophilic regenerated cellulose (RC) membrane fouled less that the more hydrophobic polyethersulfone (PES) and polyamide (PA) membranes independent of the process water used. Monosaccharide and uronic acid units could also be identified from the fouled synthetic polymeric membranes. It was impossible to analyze all monosaccharide units from the RC membrane because the analysis result obtained contained degraded membrane material. One of the fouling mechanisms of carbohydrates was adsorption. Carbohydrates were not potential adsorptive foulants to the sameextent as wood extractives because their amount in the fouled membranes was found to be significantly lower than the amount of wood extractives.

Ultrafiltration of pulp mill bleaching effluents

Main objective of this research was to find suitable polymeric ultrafiltration membranes with high retentions, good capacities and low fouling tendencies for the E2- and EP-effluent ultrafiltration. Purpose was to treat alkaline bleaching effluents with ultrafiltration in a way that permeates of the filtrations could be recycled back to process and the consumption of fresh water in the pulp mill could be reduced significantly. In the theoretical part of this work the challenges set by the pulp and paper indus-try processes for membranes were examined. An overview of the membrane tech-nology in the pulp industry was also provided. In addition process conditions in the chemical pulp bleaching and properties of bleaching effluents were discussed in literature study. In experimental part the E2- and EP-stage bleaching effluents from Stora Enso Imatra kraft pulp mill were ultrafiltered with CR250- and CR200-filters. Suitable membranes for ultrafiltration were chosen after screening experiments. Concentra-tion experiment was made for the E2-effluent in order to estimate water saving potential. The E2-effluent was finally ultrafiltered in the pulp mill in order to test the feasibility of ultrafiltration in a real industrial environment. Good membrane for the EP-effluent ultrafiltration based on the EP-screening ex-periments was polyethersulfone membrane UP020 with cut-off value of 20 000 Da. Polysulfone membrane UFX05 with cut-off value of 5 000 Da was promising membrane for the ultrafiltration of the E2-effluent. Based on the concentration filtration of the E2-effluent with UFX05 membrane the water saving potential could be 2.2 m3/Adt for the industrial scale ultrafiltration process. Retention re-sults, such as average COD retention of 60 %, from the trial filtration at the pulp mill with UFX05 membrane were modest compared to the screening experiments, where average COD retention was 75 %. Therefore tighter ultrafiltration mem-branes should be tested for the ultrafiltration of the E2-effluent. The UP020 mem-brane seemed to be suitable for the ultrafiltration of the EP-effluent however con-centration and pilot scale ultrafiltration experiments are needed to verify this.

Electro-Oxidation Treatment of Pulp and Paper Mill Circulating Waters and Wastewaters

Interest in water treatment by electrochemical methods has grown in recent years. Electrochemical oxidation has been applied particularly successfully to degrade different organic pollutants and disinfect drinking water. This study summarizes the effectiveness of the electrochemical oxidation technique in inactivating different primary biofilm forming paper mill bacteria as well as sulphide and organic material in pulp and paper mill wastewater in laboratory scale batch experiments. Three different electrodes, borondoped diamond (BDD), mixed metal oxide (MMO) and PbO2, were employed as anodes. The impact on inactivation efficiency of parameters such as current density and initial pH or chloride concentration of synthetic paper machine water was studied. The electrochemical behaviour of the electrodes was investigated by cyclic voltammetry with MMO, BDD and PbO2 electrodes in synthetic paper mill water as also with MMO and stainless steel electrodes with biocides. Some suggestions on the formation of different oxidants and oxidation mechanisms were also presented during the treatment. Aerobic paper mill bacteria species (Deinococcus geothermalis, Pseudoxanthomonas taiwanensis and Meiothermus silvanus) were inactivated effectively (>2 log) at MMO electrodes by current density of 50 mA/cm2 and the time taken three minutes. Increasing current density and initial chloride concentration of paper mill water increased the inactivation rate of Deinococcus geothermalis. The inactivation order of different bacteria species was Meiothermus silvanus > Pseudoxanthomonas taiwanensis > Deinococcus geothermalis. It was observed that inactivation was mainly due to the electrochemically generated chlorine/hypochlorite from chloride present in the water and also residual disinfection by chlorine/hypochlorite occurred. In real paper mill effluent treatment sulphide oxidation was effective with all the different initial concentrations (almost 100% reduction, current density 42.9 mA/cm2) and also anaerobic bacteria inactivation was observed (almost 90% reduction by chloride concentration of 164 mg/L and current density of 42.9 mA/cm2 in five minutes). Organic material removal was not as effective when comparing with other tested techniques, probably due to the relatively low treatment times. Cyclic voltammograms in synthetic paper mill water with stainless steel electrode showed that H2O2 could be degraded to radicals during the cathodic runs. This emphasises strong potential of combined electrochemical treatment with this biocide in bacteria inactivation in paper mill environments.

e-Business and collaboration: A case study of pulp supply chain

This thesis studies how the case company could digitalize its supply chain and what kind of advantages this would create in the light of supply chain efficiency. The case company manufactures several pulp products that are used for paper, fabrics and packaging products by customers worldwide. The paper and pulp industry has been paying more and more attention to increasing supply chain efficiency with new operating and service models made possible by today’s information technology. The main focus of this study is on the supply chain between the case company and its key customers and the goal is to find ways to make the operations between them as efficient as possible. The study relays heavily on collaboration techniques and digitalization technologies. In addition to a theoretical framework, the study includes several empirical studies that offer real-life examples of how these theories and technologies are applied in operating environments similar to the case company. A plan with strategic and operational levels is created according to the findings of the previous sections to support the case company’s future operations. The plan is based on an RFID-supported collaboration model that aims to advance information sharing between the supply chain partners. The time for an RFID-investment is sought to be very optimal and the benefits of such system to be noteworthy, but challenging to measure in monetary terms.

Sellulinjojen rejektinkäsittelyn tehokkuuden arviointi

Työssä kartoitettiin sellulinjojen rejektinkäsittelyn toimintaa ja arvioitiin rejektinkäsittelyssä liikkuvan rejektin laatua. Tavoitteena oli arvioida rejektinkäsittelyn toiminnan hyvyyttä ja löytää mahdollisia ongelmakohtia. Toiminnan hyvyyttä arvioitiin rejektinkäsittelyn ajettavuuden, hallinnan ja käytettävyyden sekä rejektin laadun perusteella. Työn kirjallisuusosassa käsitellään yleisesti sellulinjoilla esiintyviä epäpuhtauksia ja kemiallisen massan lajittelua. Kirjallisuusosan pääpaino on sellulinjan ruskean massan lajittelun ja erityisesti lajittamon rejektinkäsittelyn esittelyssä. Rejektinkäsittelyosuus käsittelee nykyaikaiseen rejektinkäsittelyyn kuuluvia laitteita ja toimintoja sekä esittelee erilaisia rejektinkäsittelyjärjestelmiä ja –vaihtoehtoja. Työn kokeellisessa osassa arvioitiin kolmen sellutehtaan kuitulinjan rejektinkäsittelyn toiminnan hyvyyttä. Arvioitavat tehdaskohteet olivat Stora Enson Kaukopään sellutehdas, Botnian Joutsenon sellutehdas sekä UPM-Kymmenen Kaukaan sellutehdas. Tavoitteena oli selvittää ruskean massan lajittelun rejektinkäsittelyssä liikkuvan rejektin laatua, jonka perusteella toiminnan hyvyyttä voitiin arvioida. Tutkimus tehtiin siten, että tehdaskäyntien aikana otettiin arviointiin tarvittavat tehdasnäytteet sekä kerättin muu arviointiin tarvittava tieto. Tehdyn tutkimuksen perusteella saatiin kokonaiskuva kolmen nykyaikaisen sellutehtaan rejektinkäsittelyn toiminnasta. Työssä saatiin runsaasti tietoa rejektinkäsittelyyn ajettavan rejektin laadusta ja määristä sekä rejektinkäsittelylaitteiden toimivuudesta. Prosessista poistettavan rejektin määrän ja laadun selvittäminen oli tehtaille erityisen tärkeä asia selvittää. Kuitutappioiden muodossa prosessista poistettavan rejektin laadulla on myös jonkinlainen taloudellinen merkitys. Arvokasta tietoa saatiin myös prosessissa liikkuvista ja poistettavista hiekkamääristä. Yleisenä havaintona oli, että työhön kuuluneilla sellutehtailla rejektinkäsittely oli hyvin hallinnassa eikä suuria ongelmakohtia löytynyt.

Pressforming of a tray from a pulp sheet

The aim of this thesis work was to verify the possibility to produce tray packages directly from pulp sheets using press forming techniques. The different existing raw materials of pulp, various sources of molded pulp and different methods of production of molded pulp were studied. Nine different raw materials which were used for experimental work were provided by Stora Enso mills, and Stora Enso Research Centre, Imatra, Finland. The laboratory tests were carried out using LUT Adjustable packaging line at Lappeenranta University of Technology. The results prove that long virgin fibres of pine pulp seems to have better formability with high moisture content compared to others. No significant improvements were noticed with conditioned samples, never the less far studies has to be done to find optimal conditions for production. The results indicated the possibility for making pressformed tray from two different pulp qualities (Sunila pulp and Enopine). The method could prove to be beneficiary as the production line could be shortened and investment in board machines could be avoided if the trays were pressed directly from pulp sheets. Also the labour costs would be reduced. However, there is much work to be done before the quality of a tray produced out of a pulp sheet is comparable to a tray produced out of tray board.

Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Aspects on Process Engineering in the Finnish Pulp and Paper Industry : Thesis for the Degree of Licentiate in Science of Technology

Process development will be largely driven by the main equipment suppliers. The reason for this development is their ambition to supply complete plants or process systems instead of single pieces of equipment. The pulp and paper companies' interest lies in product development, as their main goal is to create winning brands and effective brand management. Design engineering companies will find their niche in detail engineering based on approved process solutions. Their development work will focus on increasing the efficiency of engineering work. Process design is a content-producing profession, which requires certain special characteristics: creativity, carefulness, the ability to work as a member of a design team according to time schedules and fluency in oral as well as written presentation. In the future, process engineers will increasingly need knowledge of chemistry as well as information and automation technology. Process engineering tools are developing rapidly. At the moment, these tools are good enough for static sizing and balancing, but dynamic simulation tools are not yet good enough for the complicated chemical reactions of pulp and paper chemistry. Dynamic simulation and virtual mill models are used as tools for training the operators. Computational fluid dynamics will certainlygain ground in process design.