VVER-440 Thermal Hydraulics as a Computer Code Validation Challenge

This thesis concentrates on the validation of a generic thermal hydraulic computer code TRACE under the challenges of the VVER-440 reactor type. The code capability to model the VVER-440 geometry and thermal hydraulic phenomena specific to this reactor design has been examined and demonstrated acceptable. The main challenge in VVER-440 thermal hydraulics appeared in the modelling of the horizontal steam generator. The major challenge here is not in the code physics or numerics but in the formulation of a representative nodalization structure. Another VVER-440 specialty, the hot leg loop seals, challenges the system codes functionally in general, but proved readily representable. Computer code models have to be validated against experiments to achieve confidence in code models. When new computer code is to be used for nuclear power plant safety analysis, it must first be validated against a large variety of different experiments. The validation process has to cover both the code itself and the code input. Uncertainties of different nature are identified in the different phases of the validation procedure and can even be quantified. This thesis presents a novel approach to the input model validation and uncertainty evaluation in the different stages of the computer code validation procedure. This thesis also demonstrates that in the safety analysis, there are inevitably significant uncertainties that are not statistically quantifiable; they need to be and can be addressed by other, less simplistic means, ultimately relying on the competence of the analysts and the capability of the community to support the experimental verification of analytical assumptions. This method completes essentially the commonly used uncertainty assessment methods, which are usually conducted using only statistical methods.

Thermal reactions of the major hydrocarbon components of biomass gasification gas

Gasification of biomass is an efficient method process to produce liquid fuels, heat and electricity. It is interesting especially for the Nordic countries, where raw material for the processes is readily available. The thermal reactions of light hydrocarbons are a major challenge for industrial applications. At elevated temperatures, light hydrocarbons react spontaneously to form higher molecular weight compounds. In this thesis, this phenomenon was studied by literature survey, experimental work and modeling effort. The literature survey revealed that the change in tar composition is likely caused by the kinetic entropy. The role of the surface material is deemed to be an important factor in the reactivity of the system. The experimental results were in accordance with previous publications on the subject. The novelty of the experimental work lies in the used time interval for measurements combined with an industrially relevant temperature interval. The aspects which are covered in the modeling include screening of possible numerical approaches, testing of optimization methods and kinetic modelling. No significant numerical issues were observed, so the used calculation routines are adequate for the task. Evolutionary algorithms gave a better performance combined with better fit than the conventional iterative methods such as Simplex and Levenberg-Marquardt methods. Three models were fitted on experimental data. The LLNL model was used as a reference model to which two other models were compared. A compact model which included all the observed species was developed. The parameter estimation performed on that model gave slightly impaired fit to experimental data than LLNL model, but the difference was barely significant. The third tested model concentrated on the decomposition of hydrocarbons and included a theoretical description of the formation of carbon layer on the reactor walls. The fit to experimental data was extremely good. Based on the simulation results and literature findings, it is likely that the surface coverage of carbonaceous deposits is a major factor in thermal reactions.

Sustainability - a challenge to animal production and breeding

Selostus: Kestävän kehityksen vaatimukset kotieläintuotannossa ja -jalostuksessa

Changes in the thermal growing season in Nordic countries during the past century and prospects for the future

Selostus: Termisen kasvukauden muutokset Pohjoismaissa viimeisen vuosisadan aikana ja tulevaisuudessa

Thermal conductivity of low-decomposed Sphagnum peat used as growth medium

Kasvualustana käytetyn heikosti maatuneen rahkaturpeen lämmönjohtavuus

Experimental thermal hydraulic studies on the enhancement of safety of LWRs

The safe use of nuclear power plants (NPPs) requires a deep understanding of the functioning of physical processes and systems involved. Studies on thermal hydraulics have been carried out in various separate effects and integral test facilities at Lappeenranta University of Technology (LUT) either to ensure the functioning of safety systems of light water reactors (LWR) or to produce validation data for the computer codes used in safety analyses of NPPs. Several examples of safety studies on thermal hydraulics of the nuclear power plants are discussed. Studies are related to the physical phenomena existing in different processes in NPPs, such as rewetting of the fuel rods, emergency core cooling (ECC), natural circulation, small break loss-of-coolant accidents (SBLOCA), non-condensable gas release and transport, and passive safety systems. Studies on both VVER and advanced light water reactor (ALWR) systems are included. The set of cases include separate effects tests for understanding and modeling a single physical phenomenon, separate effects tests to study the behavior of a NPP component or a single system, and integral tests to study the behavior of the whole system. In the studies following steps can be found, not necessarily in the same study. Experimental studies as such have provided solutions to existing design problems. Experimental data have been created to validate a single model in a computer code. Validated models are used in various transient analyses of scaled facilities or NPPs. Integral test data are used to validate the computer codes as whole, to see how the implemented models work together in a code. In the final stage test results from the facilities are transferred to the NPP scale using computer codes. Some of the experiments have confirmed the expected behavior of the system or procedure to be studied; in some experiments there have been certain unexpected phenomena that have caused changes to the original design to avoid the recognized problems. This is the main motivation for experimental studies on thermal hydraulics of the NPP safety systems. Naturally the behavior of the new system designs have to be checked with experiments, but also the existing designs, if they are applied in the conditions that differ from what they were originally designed for. New procedures for existing reactors and new safety related systems have been developed for new nuclear power plant concepts. New experiments have been continuously needed.

Modeling of Pressurizer Using APROS and TRACE Thermal Hydraulic Codes

Diplomityön tavoitteena on paineistimen yksityiskohtainen mallintaminen APROS- ja TRACE- termohydrauliikkaohjelmistoja käyttäen. Rakennetut paineistinmallit testattiin vertaamalla laskentatuloksia paineistimen täyttymistä, tyhjentymistä ja ruiskutusta käsittelevistä erilliskokeista saatuun mittausdataan. Tutkimuksen päätavoitteena on APROSin paineistinmallin validoiminen käyttäen vertailuaineistona PACTEL ATWS-koesarjan sopivia paineistinkokeita sekä MIT Pressurizer- ja Neptunus- erilliskokeita. Lisäksi rakennettiin malli Loviisan ydinvoimalaitoksen paineistimesta, jota käytettiin turbiinitrippitransientin simulointiin tarkoituksena selvittää mahdolliset voimalaitoksen ja koelaitteistojen mittakaavaerosta johtuvat vaikutukset APROSin paineistinlaskentaan. Kokeiden simuloinnissa testattiin erilaisia noodituksia ja mallinnusvaihtoehtoja, kuten entalpian ensimmäisen ja toisen kertaluvun diskretisointia, ja APROSin sekä TRACEn antamia tuloksia vertailtiin kattavasti toisiinsa. APROSin paineistinmallin lämmönsiirtokorrelaatioissa havaittiin merkittävä puute ja laskentatuloksiin saatiin huomattava parannus ottamalla käyttöön uusi seinämälauhtumismalli. Työssä tehdyt TRACE-simulaatiot ovat osa United States Nuclear Regulatory Commissionin kansainvälistä CAMP-koodinkehitys-ja validointiohjelmaa.

Kaatopaikkakaasun hyötykäyttömahdollisuudet Anjalankosken Ekoparkissa

Kaatopaikalle sijoitetut biohajoavat orgaaniset jätteet muodostavat jätetäytön hapettomissa olosuhteissa kaatopaikkakaasua, joka koostuu pääasiassa metaanista ja hiilidioksidista. Kaatopaikkakaasun sisältämän metaanin takia, kaasusisältää merkittävästi energiaa, joka on hyödynnettävissä eri tavoin. Tämän diplomityön tavoitteena oli tarkastella vaihtoehtoja Anjalankosken Keltakankaan kaatopaikoilla muodostuvan kaatopaikkakaasun hyödyntämiseksi. Tarkastellut vaihtoehdot tarjoavat ympäristöllisten hyötyjen lisäksi liiketoiminnallista hyötyä Ekoparkissa toimiville yrityksille. Tutkimuksessa tehdyt laskelmatosoittivat, että työssä tarkastellut kaatopaikkakaasun hyötykäyttövaihtoehdot ovat sekä taloudellisesti että kaasun riittävyyden kannalta hyödynnettävissä. Esimerkiksi kaatopaikkakaasun hyödyntämisellä kaukolämmön tuotannossa voidaan kattaa noin kolmannes Anjalankosken vuotuisesta kaukolämmön tarpeesta. Kaatopaikkakaasun lietteen kuivauskapasiteetti kattaa Pohjois-Kymenlaaksossa muodostuvan jätevesilietteen käsittelytarpeen. Biopolttoaineen kuivauskapasiteetti on riittävä olemassa oleviin valmistuslaitosten tuotantokapasiteetteihin verrattuna. Myös perinteisillä sähkön- ja lämmöntuotantotekniikoilla voidaan kattaa Ekoparkin oma sähkön- ja lämmöntarve. Kaatopaikkavesien haihdutus ei tulosten perusteella ole sekä taloudellisesti että kaasun riittävyyden kannalta hyödynnettävissä. Tuhkan vitrifioinnissa haasteen muodostaa investointikustannuksen suuruus. Anjalankosken Ekoparkin yritykset voivat hyödyntää työn tuloksia uuden liiketoiminnan kehittämiseen. Lisäksi tuloksia voidaan hyödyntää soveltaen eri kokoluokan kaatopaikkojen kaatopaikkakaasujen hyötykäyttöä suunniteltaessa.

Validation Studies of Thermal-hydraulic Code for Safety Analysis of Nuclear Power Plants

This thesis gives an overview of the validation process for thermal hydraulic system codes and it presents in more detail the assessment and validation of the French code CATHARE for VVER calculations. Three assessment cases are presented: loop seal clearing, core reflooding and flow in a horizontal steam generator. The experience gained during these assessment and validation calculations has been used to analyze the behavior of the horizontal steam generator and the natural circulation in the geometry of the Loviisa nuclear power plant. The cases presented are not exhaustive, but they give a good overview of the work performed by the personnel of Lappeenranta University of Technology (LUT). Large part of the work has been performed in co-operation with the CATHARE-team in Grenoble, France. The design of a Russian type pressurized water reactor, VVER, differs from that of a Western-type PWR. Most of thermal-hydraulic system codes are validated only for the Western-type PWRs. Thus, the codes should be assessed and validated also for VVER design in order to establish any weaknesses in the models. This information is needed before codes can be used for the safety analysis. Theresults of the assessment and validation calculations presented here show that the CATHARE code can be used also for the thermal-hydraulic safety studies for VVER type plants. However, some areas have been indicated which need to be reassessed after further experimental data become available. These areas are mostly connected to the horizontal stem generators, like condensation and phase separation in primary side tubes. The work presented in this thesis covers a large numberof the phenomena included in the CSNI code validation matrices for small and intermediate leaks and for transients. Also some of the phenomena included in the matrix for large break LOCAs are covered. The matrices for code validation for VVER applications should be used when future experimental programs are planned for code validation.

Development of rotating drum under mechanical and thermal load

A variable temperature field sets exacting demands to the structure under mechanical load. Most of all the lifetime of the rotating drum structure depends on temperature differences between parts inside the drum. The temperature difference was known because of the measurements made before. The list of demands was created based on customers’ needs. The limits of this paper were set to the inner structure of the drum. Creation of ideas for the inner structure was started open minded. The main principle in the creation process was to create new ideas for the function of the product with the help of sub-functions. The sub-functions were created as independent as possible. The best sub-functions were combined together and the new working principles were created based on them. Every working principle was calculated separately and criticized at the end of the calculation process. The main objective was to create the new kind of structure, which is not based too much to the old, inoperative structure. The affect of own weight of the inner structure to the stress values was quite small but it was also taken into consideration when calculating the maximum stress value of the structure. Because of very complex structures all of the calculations were made with the help of the ProE – Mechanica software. The fatigue analyze was made also for the best structure solution.

Pyrolyysiöljyn tuottaminen kiertoleijukattilaan liitetyllä prosessilla

Pyrolyysiöljy on biomassasta nopealla hapettomalla lämpökäsittelyprosessilla saatavaa nestemäistä polttoainetta. Kasvavien uusiutuvan energian käyttötavoitteiden myötä pyrolyysiöljystä on tullut kiinnostava vaihtoehto fossiilisille polttoöljyille. Suurimmat käytön haasteet ovat alhainen lämpöarvo, korkeat kiintoainepitoisuudet ja happamuus fossiilisiin polttoöljyihin verrattuna sekä eri raaka-aineista syntyvät ominaisuuksiltaan erilaiset pyrolyysiöljyt. Pyrolyysiöljyn kaupallinen tuotanto on vasta käynnistymässä eikä sen laadulle ole olemassa standardeja, joten eri valmistajien tuotteet voivat poiketa toisistaan huomattavastikin. Suomessa on Valtion teknillisen tutkimuskeskuksen (VTT) toimesta kehitetty Integrated Thermal Process (ITP)-konsepti, jossa pyrolyysiöljyn tuotantoprosessi on liitetty kiertoleijukattilaprosessiin. Prosessien yhdistämisellä voidaan parantaa kokonaishyötysuhdetta sekä hyödyntää laitosten yhteistä käyttöä ja polttoaineen hankintaa. Pyrolyysiprosessin tarvitsema lämpöenergia otetaan petihiekan välityksellä kattilasta, jossa poltetaan myös prosessissa syntyvät oheistuotteet. Tässä diplomityössä tutkittiin pyrolyysiprosessin vaikutusta voimalaitoksen toimintaan ja luotiin malli voimalaitoksen energiataseessa tapahtuvien muutosten arviointiin. Malli laskee sekä pyrolysaattorin että raaka-aineen käsittelyn vaikutukset voimalaitoksen sähkön- ja lämmöntuotantoon. Lisäksi mallin avulla voidaan arvioida pyrolysaattorin aiheuttama raaka-aineen tarve sekä voimalaitoksen lisäpolttoaineen tarve. Työssä tarkasteltiin myös pyrolyysiöljyn ominaisuuksia ja käyttökohteita, sekä tarvittavia muutoksia olemassa olevaan voimalaitokseen. Lisäksi arvioitiin tuotannon kannattavuutta. Mallia sovellettiin esimerkkivoimalaitokseen, jossa on harkittu pyrolyysiöljyn tuotannon aloittamista. Laskelmien perusteella pyrolyysiöljyn tuotannolla on sähkön- ja lämmöntuotantoa alentava sekä polttoaineen tarvetta korottava vaikutus. Pyrolyysiprosessin lisääminen nostaa voimalaitoksen kokonaishyötysuhdetta. Suotuisissa olosuhteissa öljytuotanto ITP-konseptilla näyttäisi olevan taloudellisesti kannattavaa.

Supplier Energy Audits in Thermal Power Plants

This master’s thesis handles an operating model for an electric equipment supplier conducted sale oriented energy audit for pumping, fan and other motor applications at power plants. The study goes through the largest factors affecting internal electricity use at a power plant, finds an energy audit –like approach for the basis of information gathering and presents the information needed for conducting the analysis. The model is tested in practice at a kraft recovery boiler of a chemical pulping mill. Targets chosen represent some of the largest electric motor applications in the boiler itself and in its fuel handling. The energy saving potential of the chosen targets is calculated by simulating the energy consumption of the alternatives for controlling the targets, and thereafter combining the information with the volume flow duration curve. Results of the research are somewhat divaricated, as all the information needed is not available in the automation system. Some of the targets could be simulated and their energy saving potential calculated quite easily. At some of the targets chosen the monitoring was not sufficient enough for this and additional measurements would have been needed to base the calculations on. In traditional energy audits, energy efficiency of pump and fan applications is not necessarily examined. This means that there are good possibilities for developing the now presented targeted energy audit procedure basis further.

The evaluation of hazardous gas components caused by the thermal degradation of plant oils and animal fats

Neste Oil has introduced plant oils and animal fats for the production of NExBTL renewable diesel, and these raw materials differ from the conventional mineral based oils. One subject of new raw materials study is thermal degradation, or in another name pyrolysis, of these organic oils and fats. The aim of this master’s thesis is to increase knowledge on thermal degradation of these new raw materials, and to identify possible gaseous harmful thermal degradation compounds. Another aim is to de-termine the health and environmental hazards of identified compounds. One objective is also to examine the formation possibilities of hazardous compounds in the produc-tion of NExBTL-diesel. Plant oils and animal fats consist mostly of triglycerides. Pyrolysis of triglycerides is a complex phenomenon, and many degradation products can be formed. Based on the literature studies, 13 hazardous degradation products were identified, one of which was acrolein. This compound is very toxic and dangerous to the environment. Own pyrolysis experiments were carried out with rapeseed and palm oils, and with a mix-ture of palm oil and animal fat. At least 12 hazardous compounds, including acrolein, were analysed from the gas phase. According to the experiments, the factors which influence on acrolein formation are the time of the experiment, the sphere (air/hydrogen) in which the experiment is carried out, and the characteristics of the used oil. The production of NExBTL-diesel is not based on pyrolysis. This is why thermal degradation is possible only when abnormal process conditions prevail.