Pneumatic Conveying of Granular Materials in a Pilot Scale Downer-Riser System

Studies regarding the field of this work aim to substitute industrial mechanical conveyors with pneumatic conveyors to overcome the disadvantages in solids flow regulation and risks posed to production and health. The experimental part of this work examines how the granular material properties, fluidizing airflow rate, equipment geometry, and pressures along the pipes affect the mass flow rate through the system. The results are compared with those obtained from previous experiments conducted with alumina. Experiments were carried out with a pilot scale downer-riser system at Outotec Research Center Frankfurt. Granular materi-als used in this work are named as sand, ilmenite, iron ore 1 and iron ore 2.

Trigger and data link system for CMS Resistive Plate Chambers at the LHC accelerator

The purpose of the work was to realize a high-speed digital data transfer system for RPC muon chambers in the CMS experiment on CERN’s new LHC accelerator. This large scale system took many years and many stages of prototyping to develop, and required the participation of tens of people. The system interfaces to Frontend Boards (FEB) at the 200,000-channel detector and to the trigger and readout electronics in the control room of the experiment. The distance between these two is about 80 metres and the speed required for the optic links was pushing the limits of available technology when the project was started. Here, as in many other aspects of the design, it was assumed that the features of readily available commercial components would develop in the course of the design work, just as they did. By choosing a high speed it was possible to multiplex the data from some the chambers into the same fibres to reduce the number of links needed. Further reduction was achieved by employing zero suppression and data compression, and a total of only 660 optical links were needed. Another requirement, which conflicted somewhat with choosing the components a late as possible was that the design needed to be radiation tolerant to an ionizing dose of 100 Gy and to a have a moderate tolerance to Single Event Effects (SEEs). This required some radiation test campaigns, and eventually led to ASICs being chosen for some of the critical parts. The system was made to be as reconfigurable as possible. The reconfiguration needs to be done from a distance as the electronics is not accessible except for some short and rare service breaks once the accelerator starts running. Therefore reconfigurable logic is extensively used, and the firmware development for the FPGAs constituted a sizable part of the work. Some special techniques needed to be used there too, to achieve the required radiation tolerance. The system has been demonstrated to work in several laboratory and beam tests, and now we are waiting to see it in action when the LHC will start running in the autumn 2008.

A Business Incubator, Accelerator, or Coworking Space? Case Health Innovation Village at GE

Health Innovation Village at GE is one of the new communities targeted for startup and growth-oriented companies. It has been established at the premises of a multinational conglomerate that will promote networking and growth of startup companies. The concept combines features from traditional business incubators, accelerators, and coworking spaces. This research compares Health Innovation Village to these concepts regarding its goals, target clients, source of income, organization, facilities, management, and success factors. In addition, a new incubator classification model is introduced. On the other hand, Health Innovation Village is examined from its tenants’ perspective and improvements are suggested. The work was implemented as a qualitative case study by interviewing GE staff with connections to Health Innovation Village as well as startup entrepreneurs and employees’ working there. The most evident features of Health Innovation Village correspond to those of business incubators although it is atypical as a non-profit corporate business incubator. Strong network orientation and connections to venture capitalists are common characteristics of these new types of accelerators. The design of the premises conforms to the principles of coworking spaces, but the services provided to the startup companies are considerably more versatile than the services offered by coworking spaces. The advantages of Health Innovation Village are that there are first-class premises and exceptionally good networking possibilities that other types of incubators or accelerators are not able to offer. A conglomerate can also provide multifaceted special knowledge for young firms. In addition, both GE and the startups gained considerable publicity through their cooperation, indeed a characteristic that benefits both parties. Most of the expectations of the entrepreneurs were exceeded. However, communication and the scope of cooperation remain challenges. Micro companies spend their time developing and marketing their products and acquiring financing. Therefore, communication should be as clear as possible and accessible everywhere. The startups would prefer to cooperate significantly more, but few have the time available to assume the responsibility of leadership. The entrepreneurs also expected to have more possibilities for cooperation with GE. Wider collaboration might be accomplished by curation in the same way as it is used in the well-functioning coworking spaces where curators take care of practicalities and promote cooperation. Communication issues could be alleviated if the community had its own Intranet pages where all information could be concentrated. In particular, a common calendar and a room reservation system could be useful. In addition, it could be beneficial to have a section of the Intranet open for both the GE staff and the startups so that those willing to share their knowledge and those having project offers could use it for advertising.

Tuotannollisen testerin suunnittelu tiedonsiirtolinkkikortille

Työssä suunniteltiin ja toteutettiin linkkikorttien tuotannollinen testeri. Linkkikortti on osa CERN:iin rakennettavan hiukkaskiihdyttimen Large Hadron Colliderin koeasema Compact Muon Solenoidin luentajärjestelmää. Linkkikortin tehtävänä on muuttaa rinnakkaismuotoinen LVDS-signaali sarjamuotoiseksi optiseksi signaaliksi. Testattaessa testeri ja linkkikortti sijoitetaan kehikkoon, joten testerin liittimien pitää olla linkkikortin liittimien kanssa identtisiä. Testerin lähdöt ovat linkkikortin tuloja ja toisinpäin. Tällöin testattaessa voidaan ohjelmoitavien FPGA-piirien avulla lähettää signaalia kortilta toiselle. Vastaanottavan kortin FPGA-piirin avulla voidaan tarkistaa, onko data tullut perille muuttumattomana. Testin ohjaus tapahtuu tietokoneella, jolla käyttäjä antaa käskyn testin aloittamisesta ja jonne lopulta myös raportoidaan testin tulokset. Testien tulokset näytetään myös testerin ledeillä. Työssä ei pystytä linkkikorttien puuttumisen takia testaamaan testeriä loppukäytössään. Kuitenkin testerin toimivuus pystyttiin suurilta osin testaamaan, jolloin saatiin odotettuja tuloksia.

The Role of an Enterprise Portal in Knowledge Management Strategy, Case: Private Equity Investor

Työ tutkii yritysportaalin roolia organisaation tietojohtamisessa. Tutkimusongelman ratkaisemiseksi luodaan viitekehys, jossa yritysportaalin ja tietojohtamisen teoriat linkittyvät. Työn empiirisessä osassa viitekehys on pohjana case-yritykselle rakennettavalle yritysportaalille. Laadullinen tutkimus käsittää teoriaosuuden sekä osallistuvaan case-tutkimukseen perustuvan empiriaosuuden. Työn runko muodostuu kahden vastakkaisen tietojohtamisajattelun vuoropuhelusta, jotka ovat informaatioteknologiaan- ja strategiseen johtamiseen perustuvat näkökulmat. Toimivan tietojohtamismallin täytyy sisältää molemmat aspektit. Jokainen organisaatio tarvitsee informaation hallintaan liittyviä toiminnallisuuksia ja täten eksplisiittisen tiedon hallinta tietojärjestelmien avulla on onnistuneen tietojohtamisen kulmakiviä. Tätä perusinfrastruktuuria on mahdollista laajentaa hiljaisen tiedon hallintaan perustuvilla tietojohtamismenetelmillä. Työn ratkaisu näiden kahden näkemyksen, 'kovan' informaatioteknogiaan painottuvan sekä 'pehmeän' ihmisnäkökulman integrointiin, on yritysportaali. Työssä käytettävä yritysportaalin viitekehys rakentuu kolmeen päätoiminnallisuuteen; sisällönhallintaan, yhteistyöominaisuuksiin ja liiketoimintatiedon hallintaan. Työ todistaa yhteyden viitekehyksen sekä tietojohtamisen perusmallien, kuten tietojohtamisen prosessimallin sekä tietoympäristöjen välillä. Yritysportaali voi täten toimia, ei ainoastaan yksittäisten tietojohtamistyökalujen implementoinnissa, vaan tietojohtamisstrategian luomisen apuna tarjoten alustan tai 'katalyytin' kokonaisvaltaiselle tietojohtamiselle.

Fabrication and characterization of silicon position sensitive particle detectors

Position sensitive particle detectors are needed in high energy physics research. This thesis describes the development of fabrication processes and characterization techniques of silicon microstrip detectors used in the work for searching elementary particles in the European center for nuclear research, CERN. The detectors give an electrical signal along the particles trajectory after a collision in the particle accelerator. The trajectories give information about the nature of the particle in the struggle to reveal the structure of the matter and the universe. Detectors made of semiconductors have a better position resolution than conventional wire chamber detectors. Silicon semiconductor is overwhelmingly used as a detector material because of its cheapness and standard usage in integrated circuit industry. After a short spread sheet analysis of the basic building block of radiation detectors, the pn junction, the operation of a silicon radiation detector is discussed in general. The microstrip detector is then introduced and the detailed structure of a double-sided ac-coupled strip detector revealed. The fabrication aspects of strip detectors are discussedstarting from the process development and general principles ending up to the description of the double-sided ac-coupled strip detector process. Recombination and generation lifetime measurements in radiation detectors are discussed shortly. The results of electrical tests, ie. measuring the leakage currents and bias resistors, are displayed. The beam test setups and the results, the signal to noise ratio and the position accuracy, are then described. It was found out in earlier research that a heavy irradiation changes the properties of radiation detectors dramatically. A scanning electron microscope method was developed to measure the electric potential and field inside irradiated detectorsto see how a high radiation fluence changes them. The method and the most important results are discussed shortly.

Jauhatuspiirin ilmakierron optimointi

Luokittuminen erilaisine mekanismeineen aiheuttaa yleisesti ongelmia, kun on kysymyksessä kiintoaineen väliaikainenkin varastointi siilossa. Sitä voidaan vähentää kiintoaineiden, prosessin ja laitesuunnittelun muutoksilla. Tässä työssä tutkittiin mahdollisuuksia vähentää ilmeniitin luokittumista sen jauhatuspiirin ilmakiertoa optimoimalla. Suljetun kuivajauhatuspiirin keskeisimmäksi laitteeksi voitaisiin ajatella siinä oleva luokitin, joka voi olla esim. sykloni. Tässä piirissä tapahtuva kiintoaineen liikkuminen voidaan saada aikaiseksi esim. pneumaattisella kuljetuksella. Ilmeniitin jauhatus tapahtuu suljetussa kuivajauhatuspiirissä, jonka ajavana voimana on siinä oleva ilmakierto. Piirin oleellisia laitteita ovat kuulamylly, luokitin, erotussykloni ja pölykaappi sekä kiertoilma- ja poistoilmapuhaltimet. Ilmakierron optimointia varten suoritettiin kahden vastaavan jauhatuspiirin ainetasemääritykset. Lisäksi määritettiin yhden isomman piirin perustila. Jauhatuspiirien ainetasemäärityksissä määritettiin niiden massa- ja ilmavirrat sekä kiertokuorma ja luokittimen erotusterävyys, kuten myös ilmeniitin hiukkaskokojakaumat. Perustilamittauksissa määritettiin ainoastaan piirin ilmavirrat ja ilmeniitin hiukkaskokojakaumat. Optimointimittauksissa pienennettiin pikkumyllypiirin ilmamäärät vastaamaan kutakuinkin vastaavan toisen piirin määriä. Tällä yritettiin selvittää näiden toisiaan vastaavien piirien ilmamäärien ja varsinkin kiertokuormien eroavuutta. Tämä ilmamäärien pienentäminen ei tuottanut mainittavampaa muutosta piirin ainetaseisiin, joten voitaneen todeta, että piirin ilmamääriä pienentämällä saadaan aikaiseksi säästöjä, lähinnä kiertoilmapuhaltimen tehon alennuksen kautta.

Particle detector link system modifications in RE1/1 sector

The large hadron collider constructed at the European organization for nuclear research, CERN, is the world’s largest single measuring instrument ever built, and also currently the most powerful particle accelerator that exists. The large hadron collider includes six different experiment stations, one of which is called the compact muon solenoid, or the CMS. The main purpose of the CMS is to track and study residue particles from proton-proton collisions. The primary detectors utilized in the CMS are resistive plate chambers (RPCs). To obtain data from these detectors, a link system has been designed. The main idea of the link system is to receive data from the detector front-end electronics in parallel form, and to transmit it onwards in serial form, via an optical fiber. The system is mostly ready and in place. However, a problem has occurred with innermost RPC detectors, located in sector labeled RE1/1; transmission lines for parallel data suffer from signal integrity issues over long distances. As a solution to this, a new version of the link system has been devised, a one that fits in smaller space and can be located within the CMS, closer to the detectors. This RE1/1 link system has been so far completed only partially, with just the mechanical design and casing being done. In this thesis, link system electronics for RE1/1 sector has been designed, by modifying the existing link system concept to better meet the requirements of the RE1/1 sector. In addition to completion of the prototype of the RE1/1 link system electronics, some testing for the system has also been done, to ensure functionality of the design.

Simulations of 3D Stripixel Detectors

Large Hadron Collider (LHC) is the main particle accelerator at CERN. LHC is created with main goal to search elementary particles and help science investigate our universe. Radiation in LHC is caused by charged particles circular acceleration, therefore detectors tracing particles in existed severe conditions during the experiments must be radiation tolerant. Moreover, further upgrade of luminosity (up to 1035 cm-2s-1) requires development of particle detector’s structure. This work is dedicated to show the new type 3D stripixel detector with serious structural improvement. The new type of radiation-hard detector has a three-dimensional (3D) array of the p+ and n+ electrodes that penetrate into the detector bulk. The electrons and holes are then collected at oppositely biased electrodes. Proposed 3D stripixel detector demonstrates that full depletion voltage is lower that that for planar detectors. Low depletion voltage is one of the main advantages because only depleted part of the device is active are. Because of small spacing between electrodes, charge collection distances are smaller which results in high speed of the detector’s response. In this work is also briefly discussed dual-column type detectors, meaning consisting both n+ and p+ type columnar electrodes in its structure, and was declared that dual-column detectors show better electric filed distribution then single sided radiation detectors. The dead space or in other words low electric field region in significantly suppressed. Simulations were carried out by using Atlas device simulation software. As a simulation results in this work are represented the electric field distribution under different bias voltages.

Wide Area Network Acceleration in Corporate Networks

There are several factors affecting network performance. Some of these can be controlled whereas the others are more fixed. These factors are studied in this thesis from the wide area network (WAN) perspective and the focus is on corporate networks. Another area of interest is the behavior of application protocols when used through WAN. The aim is to study the performance of commonly used application protocols in corporate networks. After identifying the performance problems in corporate WANs the thesis concentrates on methods for improving WAN performance. WAN acceleration is presented as a possible solution. The different acceleration methods are discussed in order to give the reader a theoretical view on how the accelerators can improve WAN performance. Guidelines on the installation of accelerators into a network are also discussed. After a general overview on accelerators is given, one accelerator vendor currently on market is selected for a further analysis. The work is also a case study where two accelerators are installed into a target company network for testing purposes. The tests are performed with three different application protocols that have been identified as critical applications for the target corporation. The aim of the tests is to serve as a proof of concept for WAN acceleration in the target network.

Multi-Eruption Solar Energetic Particle Events Observed by SOHO/ERNE

In the last two decades of studying the Solar Energetic Particle (SEP) phenomenon, intensive emphasis has been put on how and when and where these SEPs are injected into interplanetary space. It is well known that SEPs are related to solar flares and CMEs. However, the role of each in the acceleration of SEPs has been under debate since the major role was taken from flares ascribed to CMEs step by step after the skylab mission, which started the era of CME spaceborn observations. Since then, the shock wave generated by powerful CMEs in between 2-5 solar radii is considered the major accelerator. The current paradigm interprets the prolonged proton intensity-time profile in gradual SEP events as a direct effect of accelerated SEPs by shock wave propagating in the interplanetary medium. Thus the powerful CME is thought of as a starter for the acceleration and its shock wave as a continuing accelerator to result in such an intensity-time profile. Generally it is believed that a single powerful CME which might or might not be associated with a flare is always the reason behind such gradual events.

In this work we use the Energetic and Relativistic Nucleus and Electrons ERNE instrument on board Solar and Heliospheric Observatory SOHO to present an empirical study to show the possibility of multiple accelerations in SEP events. In the beginning we found 18 double-peaked SEP events by examining 88 SEP events. The peaks in the intensity-time profile were separated by 3-24 hours. We divided the SEP events according to possible multiple acceleration into four groups and in one of these groups we find evidence for multiple acceleration in velocity dispersion and change in the abundance ratio associated at transition to the second peak. Then we explored the intensity-time profiles of all SEP events during solar cycle 23 and found that most of the SEP events are associated with multiple eruptions at the Sun and we call those events as Multi-Eruption Solar Energetic Particles (MESEP) events. We use the data available by Large Angle and Spectrometric Coronograph LASCO on board SOHO to determine the CME associated with such events and YOHKOH and GOES satellites data to determine the flare associated with such events. We found four types of MESEP according to the appearance of the peaks in the intensity-time profile in large variation of energy levels. We found that it is not possible to determine whether the peaks are related to an eruption at the Sun or not, only by examining the anisotropy flux, He/p ratio and velocity dispersion. Then we chose a rare event in which there is evidence of SEP acceleration from behind previous CME. This work resulted in a conclusion which is inconsistent with the current SEP paradigm. Then we discovered through examining another MESEP event, that energetic particles accelerated by a second CME can penetrate a previous CME-driven decelerating shock. Finally, we report the previous two MESEP events with new two events and find a common basis for second CME SEPs penetrating previous decelerating shocks. This phenomenon is reported for the first time and expected to have significant impact on modification of the current paradigm of the solar energetic particle events.

Ruokohelven käytön lisääminen Joensuun voimalaitoksen kattilassa – käytettävyys, hyötysuhde ja taloudellisuus

Ruokohelpi soveltuu ympäristöystävällisyyden ja korkean lämpöarvon vuoksi hyvin energiantuotantoon. Fortumin Joensuun voimalaitoksella ruokohelpi on syötetty kattilaan tähän asti pääasiassa pääpolttoaineisiin, turpeeseen tai hakkeeseen seostettuna pieninä energiaosuuksina. Pääpolttoaineisiin verrattuna ruokohelvellä on alhaisempi irto- ja energiatiheys, korkeampi klooripitoisuus ja kattilaa likaavampi tuhka, mikä asettaa rajoitteita sen käytön lisäämiselle voimalaitoksella. Alhaisesta irto- ja energiatiheydestä johtuvan holvautumisen sekä tukoksien lisääntymisen ja Joensuun voimalaitoksen nykyisten kuljettimien kapasiteettiongelmien vuoksi ruokohelven osuuden lisääminen suuremmaksi kuin 5 % polttoaine-energiasisällöstä on riskialtista ja edellyttää täten investointia erilliseen ruokohelven käsittely- ja syöttöjärjestelmään. Yksi vaihtoehto on murskata ruokohelpipaalit joko sähkökäyttöisellä, puolikiinteällä ja nopeakäyntisellä Haybuster H1130 tilt -murskaimella tai kiinteällä ja hidaskäyntisellä Raumaster-murskaimella ja ohjata ruokohelpisilppu joko pitkän mekaanisen kuljettimen ja sen perässä olevien lyhyiden pneumalinjojen tai pelkkien pitkien pneumalinjojen kautta suoraan kattilapesään. Työssä tutkitut investoinnit ovat taloudellisesti sitä kannattavampia mitä enemmän ruokohelpeä voidaan vuositasolla polttaa voimalaitoksella. Ruokohelven käyttömäärää voimalaitoksella kannattanee lisätä kuljetusmatkaa pidentämällä. Investointien valinta ei ole itsestäänselvyys. Nopeakäyntinen murskain on hidaskäyntistä murskainta edullisempi investointi, tosin hidaskäyntisen murskaimen käyttövarmuus on parempi kuin nopeakäyntisen murskaimen. Kattilan käytettävyyden kannalta ruokohelven käytön lisääminen edellyttää kattilan palamistekniikan analysointia laskennallisesti virtausmallinnuksella ennen kuin lopullisia päätöksiä investointien suhteen voidaan tehdä.

Design and analysis of a transversal-flux switched-reluctance-linear-machine pole-pair

The Switched Reluctance technology is probably best suited for industrial low-speed or zerospeed applications where the power can be small but the torque or the force in linear movement cases might be relatively high. Because of its simple structure the SR-motor is an interesting alternative for low power applications where pneumatic or hydraulic linear drives are to be avoided. This study analyses the basic parts of an LSR-motor which are the two mover poles and one stator pole and which form the “basic pole pair” in linear-movement transversal-flux switchedreluctance motors. The static properties of the basic pole pair are modelled and the basic design rules are derived. The models developed are validated with experiments. A one-sided one-polepair transversal-flux switched-reluctance-linear-motor prototype is demonstrated and its static properties are measured. The modelling of the static properties is performed with FEM-calculations. Two-dimensional models are accurate enough to model the static key features for the basic dimensioning of LSRmotors. Three-dimensional models must be used in order to get the most accurate calculation results of the static traction force production. The developed dimensioning and modelling methods, which could be systematically validated by laboratory measurements, are the most significant contributions of this thesis.

Leptogenesis as the origin of matter-antimatter asymmetry in extra dimensional and supersymmetric models

The Standard Model of particle physics is currently the best description of fundamental particles and their interactions. All particles save the Higgs boson have been observed in particle accelerator experiments over the years. Despite the predictive power the Standard Model there are many phenomena that the scenario does not predict or explain. Among the most prominent dilemmas is matter-antimatter asymmetry, and much effort has been made in formulating scenarios that accurately predict the correct amount of matter-antimatter asymmetry in the universe. One of the most appealing explanations is baryogenesis via leptogenesis which not only serves as a mechanism of producing excess matter over antimatter but can also explain why neutrinos have very small non-zero masses. Interesting leptogenesis scenarios arise when other possible candidates of theories beyond the Standard Model are brought into the picture. In this thesis, we have studied leptogenesis in an extra dimensional framework and in a modified version of supersymmetric Standard Model. The first chapters of this thesis introduce the standard cosmological model, observations made on the photon to baryon ratio and necessary preconditions for successful baryogenesis. Baryogenesis via leptogenesis is then introduced and its connection to neutrino physics is illuminated. The final chapters concentrate on extra dimensional theories and supersymmetric models and their ability to accommodate leptogenesis. There, the results of our research are also presented.