Characterisation of Laser Beam and Paper Material Interaction

It is known already from 1970´s that laser beam is suitable for processing paper materials. In this thesis, term paper materials mean all wood-fibre based materials, like dried pulp, copy paper, newspaper, cardboard, corrugated board, tissue paper etc. Accordingly, laser processing in this thesis means all laser treatments resulting material removal, like cutting, partial cutting, marking, creasing, perforation etc. that can be used to process paper materials. Laser technology provides many advantages for processing of paper materials: non-contact method, freedom of processing geometry, reliable technology for non-stop production etc. Especially packaging industry is very promising area for laser processing applications. However, there are only few industrial laser processing applications worldwide even in beginning of 2010´s. One reason for small-scale use of lasers in paper material manufacturing is that there is a shortage of published research and scientific articles. Another problem, restraining the use of laser for processing of paper materials, is colouration of paper material i.e. the yellowish and/or greyish colour of cut edge appearing during cutting or after cutting. These are the main reasons for selecting the topic of this thesis to concern characterization of interaction of laser beam and paper materials. This study was carried out in Laboratory of Laser Processing at Lappeenranta University of Technology (Finland). Laser equipment used in this study was TRUMPF TLF 2700 carbon dioxide laser that produces a beam with wavelength of 10.6 μm with power range of 190-2500 W (laser power on work piece). Study of laser beam and paper material interaction was carried out by treating dried kraft pulp (grammage of 67 g m-2) with different laser power levels, focal plane postion settings and interaction times. Interaction between laser beam and dried kraft pulp was detected with different monitoring devices, i.e. spectrometer, pyrometer and active illumination imaging system. This way it was possible to create an input and output parameter diagram and to study the effects of input and output parameters in this thesis. When interaction phenomena are understood also process development can be carried out and even new innovations developed. Fulfilling the lack of information on interaction phenomena can assist in the way of lasers for wider use of technology in paper making and converting industry. It was concluded in this thesis that interaction of laser beam and paper material has two mechanisms that are dependent on focal plane position range. Assumed interaction mechanism B appears in range of average focal plane position of 3.4 mm and 2.4 mm and assumed interaction mechanism A in range of average focal plane position of 0.4 mm and -0.6 mm both in used experimental set up. Focal plane position 1.4 mm represents midzone of these two mechanisms. Holes during laser beam and paper material interaction are formed gradually: first small hole is formed to interaction area in the centre of laser beam cross-section and after that, as function of interaction time, hole expands, until interaction between laser beam and dried kraft pulp is ended. By the image analysis it can be seen that in beginning of laser beam and dried kraft pulp material interaction small holes off very good quality are formed. It is obvious that black colour and heat affected zone appear as function of interaction time. This reveals that there still are different interaction phases within interaction mechanisms A and B. These interaction phases appear as function of time and also as function of peak intensity of laser beam. Limit peak intensity is the value that divides interaction mechanism A and B from one-phase interaction into dual-phase interaction. So all peak intensity values under limit peak intensity belong to MAOM (interaction mechanism A one-phase mode) or to MBOM (interaction mechanism B onephase mode) and values over that belong to MADM (interaction mechanism A dual-phase mode) or to MBDM (interaction mechanism B dual-phase mode). Decomposition process of cellulose is evolution of hydrocarbons when temperature is between 380- 500°C. This means that long cellulose molecule is split into smaller volatile hydrocarbons in this temperature range. As temperature increases, decomposition process of cellulose molecule changes. In range of 700-900°C, cellulose molecule is mainly decomposed into H2 gas; this is why this range is called evolution of hydrogen. Interaction in this range starts (as in range of MAOM and MBOM), when a small good quality hole is formed. This is due to “direct evaporation” of pulp via decomposition process of evolution of hydrogen. And this can be seen can be seen in spectrometer as high intensity peak of yellow light (in range of 588-589 nm) which refers to temperature of ~1750ºC. Pyrometer does not detect this high intensity peak since it is not able to detect physical phase change from solid kraft pulp to gaseous compounds. As interaction time between laser beam and dried kraft pulp continues, hypothesis is that three auto ignition processes occurs. Auto ignition of substance is the lowest temperature in which it will spontaneously ignite in a normal atmosphere without an external source of ignition, such as a flame or spark. Three auto ignition processes appears in range of MADM and MBDM, namely: 1. temperature of auto ignition of hydrogen atom (H2) is 500ºC, 2. temperature of auto ignition of carbon monoxide molecule (CO) is 609ºC and 3. temperature of auto ignition of carbon atom (C) is 700ºC. These three auto ignition processes leads to formation of plasma plume which has strong emission of radiation in range of visible light. Formation of this plasma plume can be seen as increase of intensity in wavelength range of ~475-652 nm. Pyrometer shows maximum temperature just after this ignition. This plasma plume is assumed to scatter laser beam so that it interacts with larger area of dried kraft pulp than what is actual area of beam cross-section. This assumed scattering reduces also peak intensity. So result shows that assumably scattered light with low peak intensity is interacting with large area of hole edges and due to low peak intensity this interaction happens in low temperature. So interaction between laser beam and dried kraft pulp turns from evolution of hydrogen to evolution of hydrocarbons. This leads to black colour of hole edges.

The Influence of Certain Processing Factors on the Durability of Yttrium Stabilized Zirconia Used As Dental Biomaterial

In dentistry, yttrium partially stabilized zirconia (ZrO2) has become one of the most attractive ceramic materials for prosthetic applications. The aim of this series of studies was to evaluate whether certain treatments used in the manufacturing process, such as sintering time, color shading or heat treatment of zirconia affect the material properties. Another aim was to evaluate the load-bearing capacity and marginal fit of manually copy-milled custom-made versus prefabricated commercially available zirconia implant abutments. Mechanical properties such as flexural strength and surface microhardness were determined for green-stage milled and sintered yttrium partially stabilized zirconia after different sintering time, coloring process and heat treatments. Scanning electron microscope (SEM) was used for analyzing the possible changes in surface structure of zirconia material after reduced sintering time, coloring and heat treatments. Possible phase change from the tetragonal to the monoclinic phase was evaluated by X-ray diffraction analysis (XRD). The load-bearing capacity of different implant abutments was measured and the fit between abutment and implant replica was examined with SEM. The results of these studies showed that the shorter sintering time or the thermocycling did not affect the strength or surface microhardness of zirconia. Coloring of zirconia decreased strength compared to un-colored control zirconia, and some of the colored zirconia specimens also showed a decrease in surface microhardness. Coloring also affected the dimensions of zirconia. Significantly decreased shrinkage was found for colored zirconia specimens during sintering. Heat treatment of zirconia did not seem to affect materials’ mechanical properties but when a thin coating of wash and glaze porcelain was fired on the tensile side of the disc the flexural strength decreased significantly. Furthermore, it was found that thermocycling increased the monoclinic phase on the surface of the zirconia. Color shading or heat treatment did not seem to affect phase transformation but small monoclinic peaks were detected on the surface of the heat treated specimens with a thin coating of wash and glaze porcelain on the opposite side. Custom-made zirconia abutments showed comparable load-bearing capacity to the prefabricated commercially available zirconia abutments. However, the fit of the custom-made abutments was less satisfactory than that of the commercially available abutments. These studies suggest that zirconia is a durable material and other treatments than color shading used in the manufacturing process of zirconia bulk material does not affect the material’s strength. The decrease in strength and dimensional changes after color shading needs to be taken into account when fabricating zirconia substructures for fixed dental prostheses. Manually copy-milled custom-made abutments have acceptable load-bearing capacity but the marginal accuracy has to be evaluated carefully.

CFD Modelling of Direct Contact Condensation in Suppression Pools by Applying Condensation Models of Separated Flow

The condensation rate has to be high in the safety pressure suppression pool systems of Boiling Water Reactors (BWR) in order to fulfill their safety function. The phenomena due to such a high direct contact condensation (DCC) rate turn out to be very challenging to be analysed either with experiments or numerical simulations. In this thesis, the suppression pool experiments carried out in the POOLEX facility of Lappeenranta University of Technology were simulated. Two different condensation modes were modelled by using the 2-phase CFD codes NEPTUNE CFD and TransAT. The DCC models applied were the typical ones to be used for separated flows in channels, and their applicability to the rapidly condensing flow in the condensation pool context had not been tested earlier. A low Reynolds number case was the first to be simulated. The POOLEX experiment STB-31 was operated near the conditions between the ’quasi-steady oscillatory interface condensation’ mode and the ’condensation within the blowdown pipe’ mode. The condensation models of Lakehal et al. and Coste & Lavi´eville predicted the condensation rate quite accurately, while the other tested ones overestimated it. It was possible to get the direct phase change solution to settle near to the measured values, but a very high resolution of calculation grid was needed. Secondly, a high Reynolds number case corresponding to the ’chugging’ mode was simulated. The POOLEX experiment STB-28 was chosen, because various standard and highspeed video samples of bubbles were recorded during it. In order to extract numerical information from the video material, a pattern recognition procedure was programmed. The bubble size distributions and the frequencies of chugging were calculated with this procedure. With the statistical data of the bubble sizes and temporal data of the bubble/jet appearance, it was possible to compare the condensation rates between the experiment and the CFD simulations. In the chugging simulations, a spherically curvilinear calculation grid at the blowdown pipe exit improved the convergence and decreased the required cell count. The compressible flow solver with complete steam-tables was beneficial for the numerical success of the simulations. The Hughes-Duffey model and, to some extent, the Coste & Lavi´eville model produced realistic chugging behavior. The initial level of the steam/water interface was an important factor to determine the initiation of the chugging. If the interface was initialized with a water level high enough inside the blowdown pipe, the vigorous penetration of a water plug into the pool created a turbulent wake which invoked the chugging that was self-sustaining. A 3D simulation with a suitable DCC model produced qualitatively very realistic shapes of the chugging bubbles and jets. The comparative FFT analysis of the bubble size data and the pool bottom pressure data gave useful information to distinguish the eigenmodes of chugging, bubbling, and pool structure oscillations.

Ammoniakin talteenottoprosessin kehitys

Diplomityössä kehitettiin ioninvaihtoon perustuva ammoniakin talteenottoprosessi NSSC (Neutral Sulphite Semi Chemical) -prosessin haihduttamon lauhteille. Tarkoituksena oli saada aallotuskartonkitehtaan kemi-kaalikiertoa suljettua ja sitä kautta ammoniakkipäästöjä vähennettyä. Ammoniakki tuli ottaa hyötymuodossa (ammoniakkihöyry tai ammoniumsulfiitti) talteen. Ammoniumsulfiittiliuosta käytetään NSSC-prosessissa keittonesteenä. Kirjallisuusosassa selvitetään strippaukseen perustuvia ammoniakin talteenottomahdollisuuksia. Tutkitaan ioninvaihdon teoriaa ja ammoniumin talteenottoon sopivien ioninvaihtomateriaalien ominaisuuksia ioninvaihtajina. Lisäksi esitetään ioninvaihtoprosesseihin liittyviä laitteistoratkaisuja ja prosessiolosuhteita. Työn kokeellisessa osassa on yleiskuvaus Powerflute Oy Savon Sellun prosesseista ja selvitetään ammoniakin merkitystä tehtaalle. Laboratoriokokein tutkittiin orgaanisten kationihartsien sekä epäorgaanisen luonnon zeoliitin soveltuvuutta ammoniumionien vaihtoon esihaihduttamon lauhteesta. Ammoniakin talteenottoprosessin toimivuutta teollisessa mittakaavassa selvitettiin rakennetulla pilotlaitteistolla suoritettujen kokeiden avulla. Lopuksi tehtiin ammoniakin talteenottoprosessin scale-up: laskettiin prosessin talteenottokapasiteetti, arvioitiin kustannuksia sekä annettiin lausunto prosessin toteutettavuudesta. Laboratoriokokeiden perusteella luonnon zeoliitti ja heikosti hapan ioninvaihtohartsi eivät sovellu ammoniumionien vaihtoon NSSC haihduttamon lauhteista. Vahvasti hapan kationihartsi toimi ammoniumin talteenotossa parhaiten, joten se valittiin pilotkokeiden ioninvaihtomateriaaliksi. Pilotkokeissa ioninvaihtomateriaaliin saatiin sidottua ammoniumia noin 30 g NH4+ / dm3 hartsia, kun materiaalin teoreettinen ioninvaihtokapasiteetti oli 32 g NH4+ / dm3 hartsia. Ammoniumin läpäisykäyrien muotoon vaikutti suuresti syöttölauhteen virtausnopeus ja ammoniumpitoisuus. Ioninvaihtomateriaalipedin syvyydellä ei ollut niinkään merkitystä. Pilotkokeiden regenerointitavoista tehokkaimmaksi osoittautui höyrystrippaus, jossa saavutettiin noin 90 %:n talteenottotehokkuus. Rikkihapokekäsittelyllä talteenottotehokkuus jäi 50 %:iin. Teollisen mittakaavan laitoksella voidaan vuosittain regenerointitavasta riippuen ottaa talteen esihaihdut-tamon lauhteesta noin 100-150 tonnia ammoniakkia. Prosessin käyttökustannukset ovat talteenotetusta ammoniakista saataviin säästöihin verrattuna suuret ja niihin vaikuttaa merkittävästi ioninvaihtohartsin käyttöikä sekä regenerointikemikaalien kulutus. Osittaisella kemikaalikierron sulkemisella saavutetaan NSSC-prosessissa sekundäärietuja, joiden vaikutuksen merkittävyys pitäisi tarkentaa lisätutkimuksilla.

Statistical Analysis and Numerics of Heat Exchanger Models

The identifiability of the parameters of a heat exchanger model without phase change was studied in this Master’s thesis using synthetically made data. A fast, two-step Markov chain Monte Carlo method (MCMC) was tested with a couple of case studies and a heat exchanger model. The two-step MCMC-method worked well and decreased the computation time compared to the traditional MCMC-method. The effect of measurement accuracy of certain control variables to the identifiability of parameters was also studied. The accuracy used did not seem to have a remarkable effect to the identifiability of parameters. The use of the posterior distribution of parameters in different heat exchanger geometries was studied. It would be computationally most efficient to use the same posterior distribution among different geometries in the optimisation of heat exchanger networks. According to the results, this was possible in the case when the frontal surface areas were the same among different geometries. In the other cases the same posterior distribution can be used for optimisation too, but that will give a wider predictive distribution as a result. For condensing surface heat exchangers the numerical stability of the simulation model was studied. As a result, a stable algorithm was developed.

Uraohjaus ja urasuunnittelu ammattikorkeakoulussa

Tutkimuksen tarkoituksena oli selvittää, millaista uraohjausta ammattikorkeakoulun tuutoriopettajat antavat ja millaista uraohjausta opiskelijat haluavat. Lisäksi tavoitteena oli selvittää, löytyykö opiskelijoiden koulutusalavalinnan perusteista yhteyttä uran suunnittelutaitoihin ja ohjauksen tarpeeseen, ja tunnistavatko tuutoriopettajat opiskelijoiden erilaiset uraohjauksen tarpeet. Tutkimuksen teoreettisissa rakenteissa hyödynnettiin kolmea postmodernia urateoriaa, jotka olivat Hodkinsonin ja Sparkesin (1997) uranvalinnan päätöksentekoteoria, Mitchellin, Lewinin ja Krumbolzin (1999) suunnitellun sattuman teoria ja Savickasin (2005) uran rakentamisteoria. Tutkimusympäristönä oli Satakunnan ammattikorkeakoulu. Tutkimus oli kaksivaiheinen. Ensimmäisessä vaiheessa kerättiin harkinnanvaraisesti valituilta tuutoriopettajilta (n=14) ja opintojensa eri vaiheissa olevilta opiskelijoilta (n=65) kirjoitettu aineisto. Kvalitatiivinen aineisto analysoitiin sisällönanalyysillä. Aineiston perusteella löydettiin kolmenlaisia urasuunnittelijoita: epävarmat, uteliaat ja tietoiset. Aineiston perusteella laadittiin kyselylomake tutkimuksen toisen vaiheen tiedonkeruuta varten. Tutkimuksen toisessa vaiheessa kerättiin opintojen eri vaiheissa olevilta opiskelijoilta kyselylomakekyselynä kvantitatiivinen aineisto (n=903), joka analysoitiin tilastollisin menetelmin. Koulutusalavalinnan perusteista elämäntilanne, alan mahdollisuudet, oma toive, kutsumus, aktiivinen tiedonhaku ja halu opiskella ammattikorkeakoulussa olivat yhteydessä opiskelijan hyvään urasuunnittelukykyyn. Näillä perusteilla koulutusalansa valinneita tietoisiksi luokiteltuja urasuunnittelijoita oli 72 % vastanneista. Alavalinnan perusteista sattuman, kavereiden, sukulaisten, lukion opinto-ohjauksen ja paikkakunnan perusteella koulutusalansa valinneet luokiteltiin epävarmoiksi urasuunnittelijoiksi, ja heitä oli 28 % vastanneista. Tulokset antavat ohjaajille tukea epävarman ja muita enemmän uraohjausta tarvitsevan opiskelijan tunnistamiseen ja heidän hops-prosessinsa tehostamiseen opintojen alusta asti. Lisäksi tulosten perusteella esitetään seuraavia suosituksia: tuutoriopettajille tulisi asettaa pätevyysvaatimukseksi ohjausalan opintojen suorittaminen; opiskelijoita tulisi ohjata tunnistamaan erilaisia satunnaisesti avautuvia mahdollisuuksia ja tietoisesti hyödyntämään niitä elämässään; uraohjaukseen tulisi kytkeä mukaan työelämäyhteistyö; ohjaajien tulisi tiivistää yhteistyötä toisen asteen ohjaajien kanssa, jotta opiskelijoiden koulutusalavalinnat onnistuisivat paremmin; uraohjausta tulisi antaa tulevaisuuden kvalifikaatioiden ennakoinnin ja elinikäisten oppimisvalmiuksien näkökulmasta.

A recent change in size distribution of blue mussels (Mytilus edulis) in the western part of the Gulf of Finland

Markus Öst & Mikael Kilpi

GIS analysis of change in an agricultural landscape in Central Finland

Selostus: Keskisuomalaisen maatalousmaiseman muutosten GIS-analyysi